Personal Home Page

http://jet.yonsei.ac.kr/

Articles in Scholarly Journals [Incomplete List]

1. Application of mesoporous TiO2 as a thermal isolation layer for infrared sensors
   Thin Solid Films, vol. 516, no. 2-4, pp. 212–215, 2007
2. Effects of Bleed Flow on Heat/Mass Transfer in a Rotating Rib-Roughened Channel
   Journal of Turbomachinery, vol. 129, no. 3, p. 636, 2007
3. Detailed Heat/Mass Transfer Distributions in a Rotating Smooth Channel With Bleed Flow
   Journal of Heat Transfer, vol. 129, no. 11, p. 1538, 2007
4. Effects of Fin Shapes and Arrangements on Heat Transfer for Impingement/Effusion Cooling with Crossflow
   Journal of Heat Transfer, vol. 129, no. 12, p. 1697, 2007
5. Pleated double-foil O-18 water target
   Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, vol. 261, no. 1-2, pp. 813–815, 2007
6. Single-phase convection and boiling heat transfer: Confined single and array-circular impinging jets
   International Journal of Multiphase Flow, vol. 33, no. 12, pp. 1271–1283, 2007
7. Influence of duct aspect ratio on heat/mass transfer in coolant passages with rotation
   International Journal of Heat and Fluid Flow, vol. 28, no. 3, pp. 357–373, 2007
8. Rotational Effects on Pressure Drop in Smooth and Ribbed Two-Pass Ducts
   Journal of Thermophysics and Heat Transfer, vol. 21, no. 3, pp. 664–667, 2007
9. Heat/Mass Transfer with Circular Pin Fins in Impingement/Effusion Cooling System with Crossflow
   Journal of Thermophysics and Heat Transfer, vol. 20, no. 4, pp. 728–737, 2006
10. Experimental study on flow and local heat/mass transfer characteristics inside corrugated duct
    International Journal of Heat and Fluid Flow, vol. 27, no. 1, pp. 21–32, 2006
11. Local Heat/Mass Transfer Characteristics on a Rotating Blade With Flat Tip in Low-Speed Annular Cascade—Part I: Near-Tip Surface
    Journal of Turbomachinery, vol. 128, no. 1, p. 96, 2006
12. Local Heat/Mass Transfer Characteristics on a Rotating Blade With Flat Tip in a Low-Speed Annular Cascade—Part II: Tip and Shroud
    Journal of Turbomachinery, vol. 128, no. 1, p. 110, 2006
13. Detailed measurement of heat/mass transfer and pressure drop in a rotating two-pass duct with transverse ribs
    Heat and Mass Transfer, vol. 43, no. 8, pp. 801–815, 2006
14. Frequency-dependent heat transfer enhancement from rectangular heated block array in a pulsating channel flow
    International Journal of Heat and Mass Transfer, vol. 48, no. 23-24, pp. 4904–4913, 2005
15. Local Heat/Mass Transfer With Various Rib Arrangements in Impingement/Effusion Cooling System With Crossflow
    Journal of Turbomachinery, vol. 126, no. 4, p. 615, 2004
16. Heat/Mass transfer in a two-pass rotating rectangular duct with and without 70?-angled ribs
    Heat and Mass Transfer, vol. 40, no. 6-7, 2004
17. Local heat/mass transfer and flow characteristics of array impinging jets with effusion holes ejecting spent air
    International Journal of Heat and Mass Transfer, vol. 46, no. 6, pp. 1049–1061, 2003
18. The Effects of Gap Position in Discrete Ribs on Local Heat/Mass Transfer in a Square Duct
    Journal of Enhanced Heat Transfer, vol. 10, no. 3, pp. 287–300, 2003
19. Flow and Heat (Mass) Transfer Characteristics in an Impingement/Effusion Cooling System With Crossflow
    Journal of Turbomachinery, vol. 125, no. 1, p. 74, 2003
20. Effects of cross ribs on heat/mass transfer in a two-pass rotating duct
    Heat and Mass Transfer, vol. 40, no. 10, pp. 743–755, 2003
21. Local heat transfer characteristics in a single rotating disk and co-rotating disks
    Microsystem Technologies, vol. 9, no. 6-7, pp. 399–408, 2003
22. Effects of acoustic excitation positions on heat transfer and flow in axisymmetric impinging jet: main jet excitation and shear layer excitation
    International Journal of Heat and Fluid Flow, vol. 24, no. 2, pp. 199–209, 2003
23. Influence of Injection Type and Feed Arrangement on Flow and Heat Transfer in an Injection Slot
    Journal of Turbomachinery, vol. 124, no. 1, p. 132, 2002
24. Heat/Mass Transfer Measurement Within a Film Cooling Hole of Square and Rectangular Cross Section
    Journal of Turbomachinery, vol. 123, no. 4, p. 806, 2001
25. Local Heat/Mass Transfer Measurement on the Effusion Plate in Impingement/Effusion Cooling Systems
    Journal of Turbomachinery, vol. 123, no. 3, p. 601, 2001
26. Heat transfer and flow structures in axisymmetric impinging jet controlled by vortex pairing
    International Journal of Heat and Fluid Flow, vol. 22, no. 3, pp. 293–300, 2001
27. Enhancement of Film Cooling Performance Using a Shaped Film Cooling Hole with Compound Angle Injection.
    JSME International Journal Series B, vol. 44, no. 1, pp. 99–110, 2001
28. Local Heat/Mass Transfer Measurements in a Rectangular Duct With Discrete Ribs
    Journal of Turbomachinery, vol. 122, no. 3, p. 579, 2000
29. Experimental mass (heat) transfer in and near a circular hole in a flat plate
    International Journal of Heat and Mass Transfer, vol. 40, no. 10, pp. 2431–2443, 1997
30. A review of mass transfer measurements using naphthalene sublimation
    Experimental Thermal and Fluid Science, vol. 10, no. 4, pp. 416–434, 1995
31. An improved low-Reynolds-number ?—? turbulence model for recirculating flows
    International Journal of Heat and Mass Transfer, vol. 37, no. 10, pp. 1495–1508, 1994
32. Transition from transpiration to film cooling*1
    International Journal of Heat and Mass Transfer, vol. 37, pp. 3–8, 1994