- About this Journal
- Abstracting and Indexing
- Aims and Scope
- Article Processing Charges
- Articles in Press
- Author Guidelines
- Bibliographic Information
- Citations to this Journal
- Contact Information
- Editorial Board
- Editorial Workflow
- Free eTOC Alerts
- Publication Ethics
- Submit a Manuscript
- Table of Contents
ISRN Mechanical Engineering
Volume 2012 (2012), Article ID 873481, 9 pages
Numerical Modelling of Squeeze Film Performance between Rotating Transversely Rough Curved Circular Plates under the Presence of a Magnetic Fluid Lubricant
1Department of Mathematics, Faculty of Engineering, Marwadi Foundation Group of Institutions, Rajkot 360 003, Gujarat State, India
2Department of Mathematics, Sardar Patel University, V. V. Nagar-388120, Gujarat State, India
Received 13 May 2012; Accepted 8 August 2012
Academic Editors: S. Cartmell, J. Hu, and R. Nagaosa
Copyright © 2012 Nikhilkumar D. Abhangi and G. M. Deheri. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
An endeavour has been made to study and analyze the behaviour of a magnetic fluid-based squeeze film between curved transversely rough rotating circular plates when the curved upper plate lying along a surface determined by an exponential function approaches the curved lower plate along the surface governed by a secant function. A magnetic fluid is used as the lubricant in the presence of an external magnetic field oblique to the radial axis. The random roughness of the bearing surfaces is characterised by a stochastic random variable with nonzero mean, variance, and skewness. The associated nondimensional averaged Reynolds equation is solved with suitable boundary conditions in dimensionless form to obtain the pressure distribution, leading to the expression for the load carrying capacity. The results establish that the bearing system registers an enhanced performance as compared to that of the bearing system dealing with a conventional lubricant. This investigation proves that albeit the bearing suffers due to transverse surface roughness, there exist sufficient scopes for obtaining a relatively better performance in the case of negatively skewed roughness by properly choosing curvature parameters and the rotation ratio. It is appealing to note that the negative variance further enhances this positive effect.
Archibald  presented a study on the squeeze film behaviour between various geometrical configurations of flat surfaces. Hays  modified the analysis of Archibald  to discuss the squeeze film phenomena between curved plates considering the curvature of sine form and keeping minimum film thickness as constant. Murti  investigated the squeeze film performance in curved circular plates describing the film thickness by an exponential expression. Indeed, his analysis was based on the assumption that the central film thickness instead of minimum film thickness considered by Hays  was constant. It was established that the load carrying capacity rose sharply with the curvature in the case of concave pads. In the above investigation the lower plate was assumed to be flat. Ajwaliya  extended the analysis of Murti  by choosing the lower plate along a surface determined by an exponential function. Patel and Deheri  developed this approach to analyze the squeeze film behaviour between curved circular plates lying along the surfaces determined by hyperbolic function. The analysis of Murti  was simplified to a larger extent by Prakash and Vij  by incorporating the well-known Morgan-Cameron approximation when the porous facing thickness was considered small.
Wu  investigated the effect of rotation between squeeze film behaviour in porous annular disks and showed that rotation caused reduced load carrying capacity as well as response time. Bhat and Patel  modified the approach of Wu  to study the effect of axial current-induced pinch on the lubrication of rotating porous annular and circular disk. Subsequently, Vora and Bhat  analyzed the load carrying capacity of a squeeze film between curved porous rotating circular plates by extending the analysis of Prakash and Vij .
Conventional lubricants were used in all the above investigations. The application of magnetic fluid as a lubricant was investigated by Verma  and Agrawal . The magnetic fluid consisted of magnetic grains suspended in a magnetically passive solvent coated with a surfactant. Bhat and Deheri  presented the study of squeeze film behaviour between porous annular disks using a magnetic fluid lubricant with the external magnetic field oblique to the lower disk. Here in this investigation it was found that the application of magnetic fluid as a lubricant enhanced the performance of the squeeze film significantly. However, the plates were considered to be flat. But in actual practice the flatness of the plate does not endure due to elastic, thermal and uneven wear effects. Taking this point into account Bhat and Deheri  studied the effect of a magnetic fluid lubricant on the configuration of Ajwaliya  by considering the two plates along the surfaces described by exponential functions. Here also, it was established that the load carrying capacity rose sharply due to the magnetic fluid lubricant. Patel and Deheri  modified the approach of Bhat and Deheri  to analyze the behaviour of a magnetic fluid-based squeeze film between curved annular plates by taking the curvature governed by hyperbolic form. Patel and Deheri  observed the magnetic fluid-based squeeze film behaviour between curved circular plates lying along a surface determined by secant functions. All these investigations underlined the importance of the curvature parameter for improving the performance of bearing system. Squeeze film performances are used din skeletal joints, bio-lubrication, extending the frequency of sensor and ear.
It is a well-known fact that particularly after having some run-in and wear the bearing surfaces develop roughness. Even the contamination of the lubricant and chemical degradation of the surfaces result in roughness. It is also a well-established fact that the randomness of the roughness and the multiple roughness scales both contribute to the complexity of the geometrical structure of the surface. Invariably, it is this complexity which contributes to most of the problem in studying and analyzing friction and wear. The random character of the surface roughness was recognized by several investigators who resorted to a stochastic approach for modelling the roughness (Tzeng and Saibel, Christensen and Tonder [17–19], Tonder ). Tzeng and Seibel  made use of a beta probability density function for the random variable characterizing the roughness. This distribution appears to be symmetrical in nature with nonzero mean. Christensen and Tonder [17–19] further developed and extended this approach of Tzeng and Saibel to present a comprehensive general analysis both for transverse as well as longitudinal surface roughness. A good number of investigations (Tonder , Ting , Prakash and tiwari , Prajapati , Guha ) adopted this approach of Christensen and Tonder [17–19] to develop the frame work for analyzing the effect of surface roughness on the performance of squeeze film behaviour. Andharia, Gupta, and Deheri  discussed the effect of transverse surface roughness on the performance of a hydrodynamic squeeze film in a spherical bearing using the general stochastic analysis. It was observed that the effect of transverse surface roughness on the performance of the bearing system was relatively adverse.
Andharia dealt with the squeeze film behaviour between rotating porous circular plates with a concentric circular pocket and studied the combined effect of elastic deformation and surface roughness. Prajapati  discussed the effect of surface roughness and rotational inertia on the optimal stiffness of hydrostatic thrust bearing.Lin, and Chinang  considered the effect of rotation on the performance of a magnetic fluid-based circular step bearing considering the bearing surfaces to be transversely rough.
Here it has been proposed to investigate the behaviour of a magnetic fluid-based squeeze film in rotating curved rough circular plates where in the upper surface is determined by an exponential expression while the surface of the curved lower plate is governed by a secant function.
The geometrical configuration of the rotating bearing system is displayed in Figure 1.
The bearing surfaces are assumed to be transversely rough. Following Christensen and Tonder [17–19] the thickness of the lubricant film is considered as where is the mean film thickness while is the deviation from the mean film thickness characterizing the random roughness of the bearing surfaces. The deviation is assumed to be stochastic in nature and described by the probability density function where is the maximum deviation from the mean film thickness. The mean , the standard deviation and the parameter which is the measure of symmetry associated with random variable are defined by the relations while denotes the expected value given by the following: where It is assumed that rotating upper plate lying along the surface determined by the following: approaching with normal velocity , to the rotating lower plate lying along the surface where is central distance between the plates, B and are the curvature parameters of the corresponding plates. The central film thickness then, is defined by the following: The lower and upper plate rotate with angular velocities is and , respectively.
Axially symmetric flow of the magnetic fluid between the plates is taken into consideration under an oblique magnetic field whose magnitude vanishes at ; for instance where is a suitably chosen constant so as to have a magnetic field of required strength, which suits the dimensions. The direction of the magnetic field plays a significant role since has to satisfy the relations (Agrawal , Bhat and Deheri ) Therefore, arises out of a potential function and the inclination angle of the magnetic field with the lower plate is determined by the following: whose solution is determined from the equation where is a constant of integration.
The modified Reynolds equation governing the film pressure then can be obtained as (Bhat and Deheri , (Patel et al.  and Prajapati ) where Introducing the nondimensional quantities and solving the associated Reynolds equation with the concerned boundary conditions one gets the expression for nondimensional pressure distribution where
The dimensionless load carrying capacity then, is given by the following: where the load carrying capacity is obtained from the relation
3. Results and Discussions
It is clearly seen that the nondimensionless pressure distribution and load carrying capacity are determined from (18), (20), respectively. It is also clear that these performance characteristics depend on various parameters such as , , , B, C, S, and . These parameters, respectively, show the effect of magnetic fluid lubricant, roughness, curvature, and rotation, respectively. Taking the roughness parameters to be zero this study reduces to the corresponding magnetic fluid-based squeeze film performance in curved smooth rotating circular plates. Further, taking this discussion reduces to squeeze film performance in curved smooth rotating circular plates. Besides, in the absence of rotation this investigation gets reduced essentially to the performance of squeeze film between circular plates.
From (20) governing the distribution of load carrying capacity it is easily observed that the dimensionless load carrying capacity increases by as compared to that of conventional lubricants. The variation of nondimensional load carrying capacity with respect to the magnetization parameter is presented in Figures 2, 3, 4, 5, 6, 7, and 8 for various values of , , B, C, S, and . These figures tend to indicate that the load carrying capacity increases significantly with respect to the magnetization parameter. It is noticed that among the roughness parameters the combined effect of the magnetization and skewness is more pronounced. However, the effect of tends to be almost negligible at the initial stages (up to ). Furthermore, a symmetrical nature of the distribution of load carrying capacity is observed with respect to the lower plate’s curvature parameter. The effect of with respect to the lower plate’s curvature parameter is almost negligible upto the value of .
Figures 9, 10, 11, 12, 13, and 14 depict the effect of standard deviation associated with the roughness on the distribution of load carrying capacity. It can be easily seen from these figures that the effect of standard deviation is basically adverse in the sense that the load carrying capacity decreases considerably. In addition, this negative effect of is relatively less in the case of upper plate’s curvature parameter. Besides, the effect of rotational inertia with respect to the standard deviation is however negligible at the initial stage.
In Figures 15, 16, 17, 18, and 19 one can visualize the effect of variance on the distribution of load carrying capacity. These figures suggest that decreases the load carrying capacity while increases the load carrying capacity. Further, it is indicated that the combined effect of the upper plate’s curvature parameter and the negative variance is significantly positive.
The effect of skewness on the distribution of load carrying capacity is given in Figures 20, 21, 22, and 23. As in the case of variance here also positively skewed roughness decreases the load carrying capacity while the load carrying capacity increases due to the negatively skewed roughness. Furthermore, there is manifest a symmetric distribution of the load carrying capacity with respect to the lower plate curvature parameter.
The combined effect of the curvature parameters is presented in Figure 24. It is easily seen that the upper plate’s curvature parameter increases the load carrying capacity while effect of upper plate curvature parameter with respect to lower plate’s curvature parameter is almost negligible.
Finally, the effect of rotation is presented in Figures 25, 26, 27, 28, and 29. It is clear that the effect of rotation is quite sharp. One can observe that the effect of lower plate curvature parameter with respect to is almost negligible. It is established from these figures that the load carrying capacity decreases with respect to the rotation ratio upto the value and afterwards the load carrying capacity increases. The rate of increase in load carrying capacity due to rotation is comparatively more in the case of lower plate curvature parameter while the rate of decrease with respect to is more in the case of rotational inertia S.
Some of these figures indicate that the increased load carrying capacity due to upper plate’s curvature parameter gets further increased in the case of negatively skewed roughness and this further enhances when negative variance occurs. It is revealed that the negative effect induced by the transverse surface roughness can be compensated upto some extent by the magnetization parameter choosing a suitable combination of curvature parameter and rotation ratio parameter in the case of negatively skewed roughness.
A comparison of the results presented here and the discussion of Patel and Deheri  indicates that at least the load carrying capacity increases by 3% to 4% in spite of the fact that the roughness has an adverse effect on the performance of bearing system. Further, in view of the deliberations of Patel and Deheri  of our article are provided and additional degrees of freedom in terms of the ratio of the curvature parameter for improving the performance of the squeeze film.
This investigation makes it clear that the roughness merits a serious attention while designing this magnetic fluid based bearing system even if suitable values of curvature parameter and rotation ratio are chosen. This is all the more important from the bearings life period point of view. In addition, the bearing can support a load even in the absence of flow unlike the case of a conventional lubricant.
|Radius of the upper plate|
|:||Radius of the lower plate|
|:||Curvature parameter of the upper plate|
|:||Curvature parameter of the lower plate|
|:||Magnitude of the magnetic field|
|:||Load carrying capacity|
|:||Constant of integration|
|:||Nondimensional load carrying capacity|
|:||Free space permeability|
The constructive suggestions, critical remarks, and in-depth comments of referees leading to overall improvement on the presentation of the paper are gratefully acknowledged.
- F. R. Archibald, “Load capacity and time relations for squeeze films,” ASME, vol. 78, pp. A231–A245, 1956.
- D. F. Hays, “Squeeze films for rectangular plates,” ASME, vol. 58, pp. 243–248, 1963.
- Murti .PR.K., “Squeeze films in curved circular plates,” ASME Transactions, Journal of Lubrication Technology, vol. 97, no. 4, pp. 650–652, 1975.
- M. B. Ajwaliya, On certain theoretical studies in hydrodynamic and electro magnetohydrodynamic lubrication [Ph.D. thesis], S. P. University, V. V. Nagar, 1984.
- R. M. Patel and G. M. Deheri, “Analysis of the behaviour of the squeeze film between curved plates,” The Journal of the Indian Academy of Mathematics, vol. 24, no. 2, pp. 333–338, 2002.
- J. Prakash and S. K. Vij, “Load capacity and time-height relations for squeeze films between porous plates,” Wear, vol. 24, no. 3, pp. 309–322, 1973.
- H. Wu, “The squeeze film between rotating porous annular disks,” Wear, vol. 18, no. 6, pp. 461–470, 1971.
- M. V. Bhat and K. C. Patel, “The effect of axial-current-induced pinch on the lubrication of rotating porous annular and circular discs,” Wear, vol. 50, no. 1, pp. 39–46, 1978.
- K. H. Vora and M. V. Bhat, “The load capacity of a squeeze film between curved porous rotating circular plates,” Wear, vol. 65, no. 1, pp. 39–46, 1980.
- P. D. S. Verma, “Magnetic fluid-based squeeze film,” International Journal of Engineering Science, vol. 24, no. 3, pp. 395–401, 1986.
- V. K. Agrawal, “Magnetic-fluid-based porous inclined slider bearing,” Wear, vol. 107, no. 2, pp. 133–139, 1986.
- M. V. Bhat and G. M. Deheri, “Squeeze film behaviour in porous annular discs lubricated with magnetic fluid,” Wear, vol. 151, no. 1, pp. 123–128, 1991.
- M. V. Bhat and G. M. Deheri, “Magnetic fluid based squeeze film between two curved circular plates,” Bulletin of Calcutta Mathematical Society, vol. 85, pp. 521–524, 1993.
- R. M. Patel and G. M. Deheri, “behaviour of the squeeze film between annular plates,” The Journal of Engineering and Technology, vol. 16, pp. 50–53, 2003.
- R. M. Patel and G. M. Deheri, “Magnetic fluid based squeeze film between two curved plates lying along the surfaces determined by secant functions,” Indian Journal of Engineering and Materials Sciences, vol. 9, no. 1, pp. 43–48, 2002.
- S. T. Tzeng and E. Saibel, “Surface roughness effect on slider bearing lubrication, Transaction,” ASME Transactions, Journal of Lubrication Technology, vol. 10, pp. 334–338, 1967.
- H. Christensen and K. C. Tonder, “Tribology of rough surfaces: stochastic models of hydrodynamic lubrication,” SINTEF Report 10/69-18, 1969.
- H. Christensen and K. C. Tonder, “The hydrodynamic lubrication of rough bearing surfaces of finite width,” in ASME-ASLE Lubrication Conference, Cincinnati, Ohio, USA, 1970, paper no. 70-Lub-7.
- H. Christensen and K. C. Tonder, “Tribology of rough surfaces: parametric study and comparison of lubrication models,” SINTEF Report 22/69-18, 1969.
- K. C. Tonder, “Surface distributed waviness and roughness,” in First World Conference in Industrial Tribology, vol. 3, pp. 1–8, 1972.
- L. L. Ting, “Engagement behaviour of lubricated porous annular disks. Part1: squeeze film phase, surface roughness and elastic deformation effects,” Wear, vol. 34, pp. 159–182, 1975.
- J. Prakash and K. Tiwari, “Roughness effects in porous circular squeeze-plates with arbitrary wall thickness,” Journal of Lubrication Technology, vol. 105, no. 1, pp. 90–95, 1983.
- B. L. Prajapati, “Behavior of squeeze film between rotating porous circular plates: surface roughness and elastic deformation effects,” Pure and Applied Mathematika Sciences, vol. 33, no. 1-2, pp. 27–33, 1991.
- S. K. Guha, “Analysis of dynamic characteristics of hydrodynamic journal bearings with isotropic roughness effects,” Wear, vol. 167, no. 2, pp. 173–179, 1993.
- J. L. Gupta and G. M. Deheri, “Effect of roughness on the behavior of squeeze film in a spherical bearing,” Tribology Transactions, vol. 39, no. 1, pp. 99–102, 1996.
- P. I. Andharia, J. L. Gupta, and G. M. Deheri, “Effect of transverse surface roughness on the behavior of squeeze film in a spherical bearing,” Journal of Applied Mechanics and Engineering, vol. 4, pp. 19–24, 1999.
- B. L. Prajapati, “Squeeze film behaviour between rotating porous circular plates with a concentric circular pocket: surface roughness and elastic deformation effects,” Wear, vol. 152, no. 2, pp. 301–307, 1992.
- J. R. Lin and C. F. Chinang, “Effects of surface roughness and rotational inertia on the optimal stiffness of hydrostatic thrust bearings,” International Journal of Applied Mechanics and Engineering, vol. 7, no. 4, pp. 1247–1261, 2002.
- H. C. Patel, G. M. Deheri, and R. M. Patel, “Performance of Magnetic fluid based rotating rough circular step bearing,” International Journal of Applied Mechanics and Engineering, vol. 13, no. 2, pp. 441–455, 2008.