- About this Journal
- Abstracting and Indexing
- Aims and Scope
- Article Processing Charges
- Articles in Press
- Author Guidelines
- Bibliographic Information
- Citations to this Journal
- Contact Information
- Editorial Board
- Editorial Workflow
- Free eTOC Alerts
- Publication Ethics
- Submit a Manuscript
- Table of Contents
ISRN Organic Chemistry
Volume 2013 (2013), Article ID 417672, 27 pages
Chemical Modification of Polysaccharides
Private Practice, UK
Received 15 May 2013; Accepted 9 June 2013
Academic Editors: D. K. Chand and E. Lee-Ruff
Copyright © 2013 Ian Cumpstey. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
This review covers methods for modifying the structures of polysaccharides. The introduction of hydrophobic, acidic, basic, or other functionality into polysaccharide structures can alter the properties of materials based on these substances. The development of chemical methods to achieve this aim is an ongoing area of research that is expected to become more important as the emphasis on using renewable starting materials and sustainable processes increases in the future. The methods covered in this review include ester and ether formation using saccharide oxygen nucleophiles, including enzymatic reactions and aspects of regioselectivity; the introduction of heteroatomic nucleophiles into polysaccharide chains; the oxidation of polysaccharides, including oxidative glycol cleavage, chemical oxidation of primary alcohols to carboxylic acids, and enzymatic oxidation of primary alcohols to aldehydes; reactions of uronic-acid-based polysaccharides; nucleophilic reactions of the amines of chitosan; and the formation of unsaturated polysaccharide derivatives.
With increasing oil prices and forecasts of a future lack of availability, renewable non-petrochemical-based alternatives to materials synthesis could become more important. Polysaccharides are the products of a natural carbon-capture process, photosynthesis, followed by further biosynthetic modifications. Some are produced on a very large scale in nature, and some have industrial relevance with, for example, materials and food applications, either in their native or chemically modified forms. This review covers methods for the chemical modification of polysaccharides. The topic of general modification of polysaccharides has been reviewed previously , and several more specific reviews are referenced later. In this review, I have limited myself to discussing the synthesis of modifications whereby the polymeric chain remains intact—or at least while degradation may take place to some extent, the products are still polysaccharides. The conversion of polysaccharides into small molecules has been reviewed elsewhere [2, 3] and is not covered here.
Chemical modification can change the character of the polysaccharides, for example, rendering them hydrophobic . Some such processes, such as the formation of cellulose esters (including nitrocellulose, celluloid, cellulose acetate), are very well known and have been carried out at an industrial level for more than a hundred years. The object of this review is not to cover such well-known processes in detail but rather to describe published results of current research and the state-of-the-art in polysaccharide derivatisation. Neither have I gone into details about the possible applications of the products but have focussed on aspects related to reactivity and chemical structure. The modifications are presented classified by reaction type.
The structures of the natural (native) polysaccharides whose chemical modification is described in this review are shown in Figure 1. Structurally, the simplest molecules consist of a monosaccharide repeating unit with hydroxyl groups as the only functional groups. Examples of this type of structure include the very common polysaccharides, cellulose and amylose. Other related structures such as curdlan, a (β1–3)-linked glucan, and inulin, the only polysaccharide based on furanosides considered here, also have simple structures. Amylopectin has a structure similar to amylose (these to polysaccharides are the components of starch), but it is a branched structure, with many amylose-like chains linked together by (α1–6)-branching points. Dextran is basically an (α1–6)-linked glucan, but it may have a little or a lot of branching at the secondary hydroxyl groups. For example, in so-called regular comb dextran, every residue in the backbone is substituted by an (α1–3)-linked glucose unit. Xylans, a component of hemicelluloses, are made up of a (β1–4)-linked xylopyranose backbone, but it also may be branched, for example, by 4-O-methylglucuronic acid, or acetylated to a greater or lesser degree. Xylose is a pentose, so the pyranose units in xylan do not have a primary hydroxyl group. Guar gum and locust bean gum both consist of (β1–4)-linked mannan backbones substituted by Gal(α1–6) units to some extent. In guar gum, approximately every other mannose residue is substituted with galactose, whereas in locust bean gum, long unsubstituted regions alternate with regions of heavy galactose branching.
Pullulan, alternan, and lichenan are glucans with more than one type of glycosidic linkage in the polysaccharide backbone. Pullulan is an unbranched polysaccharide with three monosaccharides in the repeating unit, [Glc(α1–4)Glc(α1–4)Glc(α1–6)]. Alternan has two monosaccharides in its repeating unit, [Glc(α1–3)Glc(α1–6)], but it can also contain some Glc(α1–3) branching. Lichenan is an unbranched polysaccharide based on glucose with mixed (β1–3) and (β1–4) linkages.
Some polysaccharides have other functional groups as well as the simple hydroxyl groups. Alginates and pectins are based on uronic acids; their monosaccharide constituents are all oxidised at C-6 to the carboxylic acid level. Alginates consist of domains of (α1–4)-linked L-guluronic acid interspersed with domains of (β1–4)-linked mannuronic acid. Pectins are polysaccharides rich in galacturonic acid, although this acid commonly will be found as its methyl ester. A simple backbone of (α1–4)-linked galacturonic acid methyl ester may also be substituted by other monosaccharide branches.
A very common polysaccharide based on aminosugars is chitin/chitosan. The chitin/chitosan relationship can be regarded as a continuum, with polysaccharides containing more of the free base being called chitosan and those mostly N-acetylated being called chitin.
The extent of derivatisation reactions is given in terms of the degree of substitution (DS). The DS is defined as the number of substitutions made per monomer unit. The maximum DS will depend on the structure and reaction in question. For example, cellulose has three hydroxyl groups per monomer, so in an acetylation of cellulose, all three may be acetylated, and the maximum DS would be 3. But only one of the alcohols is primary, so in an oxidation reaction that only acted on primary alcohols, the maximum DS would be 1. The degree of polymerisation (DP) is another important factor, giving an average length (expressed in number of monomer units) of the polysaccharide. A loss in DP during a reaction indicates that degradation of the polysaccharide backbone has occurred. It has been pointed out that many reports use cellulose with low DP (which is more soluble) and also that many do not comment on whether there is any decrease in DP during derivatisation reactions . Order of magnitude values of the DP of cellulose samples could be ca 280 for Avicel and ca 2000 for cotton linters .
If uniform partial derivatisation is to be achieved, it can be important that the reaction is conducted in homogeneous solution. This is less important if the goal is complete derivatisation of a polysaccharide. Running a reaction under homogeneous conditions may also lead to a cleaner product, due to fewer side reactions, as less forcing conditions (lower reaction temperature and lower excesses of reagents) may be necessary than in heterogeneous reactions; hence, the choice of an appropriate solvent for a polysaccharide substrate is important. “Swelling” of solid material by a solvent will not dissolve the solid to give a homogeneous solution, but it will nevertheless increase the accessibility of the reactive groups of the polymer to reagents in solution.
Polysaccharides are often insoluble in water or organic solvents, so solvent mixtures can be used. Non-aqueous solvent mixtures that dissolve cellulose often consist of an organic liquid and an inorganic salt. Examples include DMA (dimethylacetamide)/LiCl; DMF/LiCl; DMI (1,3-dimethyl-2-imidazolinone)/LiCl; and DMSO/TBAF (tetrabutylammonium fluoride). The DMSO/Et3N/SO2 mixture is a salt-free solvent for cellulose. It will sometimes be necessary to heat to high temperature (150°C) before cellulose will dissolve in these solvents, but it will then remain in solution on cooling. Inorganic salts are often formed as by-products in derivatisation reactions (e.g., stoichiometric NaCl would be formed in a benzylation reaction using NaOH/BnCl), so when they are added at the start of a reaction to aid solubility, this is unlikely to cause problems in itself.
Similar solvents or solvent mixtures to those used for cellulose are often used for other neutral polysaccharides, but many are more soluble and some are water-soluble. Starch is generally more soluble than cellulose. Solvents for chitin include LiCl (5%)/DMA, LiCl/N-methyl-2-pyrrolidone, CaCl2/MeOH, and hexafluoroisopropyl alcohol.
Charged polysaccharides such as chitosan (which may be protonated on nitrogen) or polyuronates such as alginates (which can form carboxylate salts) will have very different solubility properties. Hence, chitosan is soluble in aqueous organic or mineral acids below pH 6.5 and also in DMSO.
Ionic liquids (room-temperature ionic liquids) are relatively new solvents that have found use in polysaccharide chemistry [7, 8]. They can dissolve polysaccharides, including cellulose, hemicellulose, and wood, allowing derivatisation reactions to take place under homogeneous conditions. Cellulose dissolves in ionic liquids, aided by conventional heating, microwave irradiation, or sonication, with up to 25% (w/w) being obtained in [bmim]Cl . Other ionic liquids gave 5–10% w/w solutions of cellulose. The properties of ionic liquids can be fine-tuned by structural modification of one or other of the two ionic components. Increasing the length of the alkyl chains in the cation component resulted in a less efficient dissolution of cellulose. Amylose was shown to have a very high solubility in ether-derived ionic liquids. Ionic liquids have been called “green” solvents due to their recyclability and low vapour pressures (low volatility), but a low vapour pressure can limit the recyclability of a solvent, as it can make its purification difficult after it has been used in chemical reactions. As a result, volatile and distillable ionic liquids have been designed for polysaccharide derivatisation .
2. Saccharide Oxygen as Nucleophile
This section covers the formation of ethers and esters, in which the saccharide oxygen acts as a nucleophile in the reaction and is retained in the product. Different degrees of reaction can be considered. As well as very low DS, where only a few hydroxyl groups per polysaccharide chain are derivatised, and maximum DS, where all the hydroxyl groups are derivatised, and points in between these extremes, we can consider regioselective reactions in which a single hydroxyl group on each monosaccharide residue reacts preferentially to (say) near completion. Regioselective reactions allow the synthesis of structurally well-defined products. But more than this, if a regioselective reaction goes to completion, reaching DS = 1, then it can be followed in principle by further derivatisations that do not have to be selective, but that can nevertheless introduce further functionality at specific positions in a polysaccharide structure.
There is a significant disadvantage of working with polysaccharides when it comes to matters of regioselectivity. In monomeric molecules, when a reaction gives incomplete regioselectivity (resulting in the formation of regioisomers, disubstituted or trisubstituted products, etc.) the desired product may be purified from the other components of the product mixture by crystallisation or chromatography. In polysaccharides, any such purification is impossible, as correctly modified monosaccharide residues of the polysaccharide will be covalently linked to incorrectly modified monosaccharide residues. This means that only the most regioselective modifying reactions may be used for polysaccharide modification if a homogeneous polysaccharide structure is required.
Typical alkylating agents include alkyl halides (chlorides, bromides, iodides) or, less commonly, alkyl sulfonates. Normally, a strong base will be used to deprotonate the alcohol to give the alkoxide. Alkylation reactions generally have a poor water-compatibility, as water can hydrolyse the alkylating agent.
2.1.1. Alkyl and Benzyl Ethers
The formation of cellulose ethers under homogeneous conditions in typical nonderivatising solvents is possible, but it is more problematic than ester formation (see below). The solvent of choice for cellulose etherification appears to be DMI (1,3-dimethyl-2-imidazolidinone)/LiCl . In this solvent, much lower excesses of reagent were required than with alternative solvents. First the cellulose was dissolved by briefly heating to 150°C. Treatment with NaOH and MeI for 5 h at 70°C gave 2,3,6-tri-O-methylcellulose with a DS of 3. It should be pointed out that when the NaOH was added, the cellulose crashed out of solution to some extent, and so the reaction was in fact not entirely homogeneous.
Complete etherification (i.e., tri-O-alkylation) of cellulose was also investigated in other solvents for etherification with various alkyl groups. Different solvents and bases were evaluated in the benzylation reaction, and the best conditions of those tested were found to be powdered NaOH and BnCl (both in an excess of 10 equiv./hydroxyl), in a solvent of DMSO/SO2/Et2NH, heating at ca 80°C for 3-4 h . DMSO/N2O4 and DMA/LiCl gave slightly worse results. Subsequent papers covered the formation of substituted benzyl ethers and allyl ethers  and of simple alkyl ethers  of cellulose, all under essentially the same reaction conditions. Purification was achieved by extraction into chloroform, precipitation after the addition of EtOH, and then washing with water, EtOH and hexane.
In DMA/LiCl, methyl, hydroxyethyl, and hydroxypropyl ethers of cellulose could be formed under homogeneous conditions, using iodomethane or the epoxides as alkylating agents . But high excesses of reagents were required, slow reactions were seen, and only products with low DS values (1.1–1.7) were accessible. A DMSO/LiCl solvent was used for the homogeneous etherification (methyl, ethyl, propyl, and butyl peretherification) of cellulose, using dimsyl sodium (from NaH and DMSO) as base .
Ionic liquids have been tested as solvents for the etherification of polysaccharides (cellulose and starch) under basic conditions but with little success to date, in contrast to esterification reactions (see below) .
Other polysaccharides have also been shown to undergo peretherification reactions under similar conditions. Xylan was benzylated using BnBr, NaOH, and 18-crown-6 in DMSO , and amylose was converted into its tri-O-benzyl derivative by treatment with NaOH and BnCl in DMSO . A detailed investigation into the benzylation of starch in water (NaOH, BnCl) was reported . As expected, widespread hydrolysis of the BnCl occurred under these conditions.
The benzylation of chitin was reported . β-Chitin was suspended in DMSO, and sodium hydride (5 equiv.) and benzyl chloride (10 equiv.) were added. After heating at 60°C for 24 h, the product (DS = 1.33) was obtained by precipitation from MeOH. When more NaH (7 equiv.) was used, a product with DS = 2 was obtained, but N-alkylation is likely to occur as well as O-alkylation under such reaction conditions. Alternatively, chitin was suspended in DMSO and treated with KOH; this insoluble deprotonated chitin was then filtered and washed to remove water, then it was resuspended in DMSO and BnCl was added. This method gave the product with a DS of up to 0.8 .
Considering other alkyl ethers, amylose and starch were treated with propyl bromide and NaOH in DMSO to give propyl ethers with DS of up to 3.0 . The purification of polysaccharides with high DS was achieved by precipitation from water, but those with low DS were more difficult to purify. Pullulan was converted into its propyl and butyl ethers with DS between 1 and 2.6 by treatment with the alkyl bromides and NaOH in H2O/DMSO .
2.1.2. Carboxymethyl Ethers
Carboxymethyl cellulose is an industrially important ionic cellulose ether, and the synthesis of this type of derivative based on some hemicellulose polysaccharides has been investigated to some extent. The synthesis of carboxymethyl ethers of xylan was investigated under homogeneous conditions (in water) or slurry conditions (in i-PrOH or EtOH/toluene) using NaOH as base and ClCH2COONa as alkylating agent . Guar gum was derivatised with carboxymethyl ethers in water or in EtOH/toluene (as for xylan, above) to give a product with a DS of 0.8. Repeating the procedure gave further substitution and a product with a higher DS . Konjac glucomannan was derivatised with carboxymethyl ethers in methanol to give a product with a DS of 0.3 .
2.1.3. Hydroxyethyl Ethers
Other than cellulose derivatives, which are produced industrially by epoxide-ring opening, guar gum and xylan were etherified (up to DS = 2) by treatment with ethylene oxide or propylene oxide and sodium hydroxide .
2.2.1. Acetate and Other Carboxylate Esters
Carboxylate esters can be formed using carboxylic acids as acylating agents under strong-acid catalysis (Fischer esterification) or by using an activated derivative such as an acid chloride or anhydride, either with base or with a Lewis acid.
The strong-acid catalysis method is used to produce cellulose acetate, an important industrial product . But this method does not produce the triacetate, due to partial transient sulfation during the reaction. Cellulose triacetate can be prepared in a similar way using an acid catalyst that does not covalently attach to the cellulose, such as HClO4.
When an activated carboxylic acid derivative (e.g., acid anhydride, acid chloride) reacts with an alcohol under basic conditions, the base should be present in a stoichiometric amount (it will be protonated by the acid by-product of the reaction), but it can be a weak base, such as pyridine or triethylamine.
(1) Homogeneous Reactions. Cellulose carboxylates (DS of up to 2.4–2.8) were prepared by the reaction of cellulose under homogeneous conditions in DMA/LiCl solution with acid chlorides and triethylamine or with acid anhydrides and sulfuric acid . The cellulose carboxylate products were purified by precipitation into water followed by Soxhlet extraction into methanol. Similarly, starch was esterified with acyl chlorides and pyridine in DMA/LiCl solution at 100°C for 6 h, followed by purification by precipitation . With long-chain fatty acid chlorides, DS values of up to 3 were seen.
Xylan acetates with DS of up to 2 (i.e., complete acetylation) could be prepared either with Ac2O/pyridine in DMF/LiCl or under acid catalysis in AcOH . Alternatively, a xylan acetate with high DS (≈1.9) and clean 1H NMR spectra was prepared using Ac2O and pyridine in DMF . With longer-chain acyl chlorides, xylan reacted under homogeneous conditions in DMF/LiCl to give polysaccharides with lower DS values (0.3–1.5) .
Vinyl carboxylates have also been used as acyl donors, reacting spontaneously with cellulose in DMSO/TBAF to give polysaccharides with DS values of up to 2.6 .
The acetylation of cellulose in an ionic liquid solvent, [amim]Cl (1-allyl-3-methylimidazolium chloride), was achieved in 2004 using acetic anhydride to give products with DS of ca 2.5–2.7 . The esterification of cellulose in ionic liquids is straightforward for short-chain esters . Several ionic liquids gave similarly good results, with [bmim]Cl (1-butyl-3-methylimidazolium chloride) being the best. Acetic anhydride or acetyl chloride reacted with cellulose without any added base within 2 h at 80°C to give cellulose acetates with DS of up to 3. However, only lower DS values (e.g., 1.6 for lauryl chloride) were obtainable with fatty acid chlorides in ionic liquids, presumably because the partially acylated polysaccharide becomes more and more nonpolar until it precipitates out of the polar ionic solvent, stopping the reaction.
The use of carboxylic acids themselves as acylating agents rather than derivatives such as acid anhydrides or acyl chlorides could be attractive, as the acids may have a wider availability and be more soluble in polar solvents. The Fischer esterification using the carboxylic acid as solvent and with strong-acid catalysis has already been mentioned, but in situ activation of carboxylic acids under mild conditions can also be used for polysaccharide acylation. When tosyl chloride was used as an activating agent for with various long-chain carboxylic acids in a DMSO/TBAF solvent, acylated celluloses with DS of up to 2.6–2.9 could be formed [32, 35]. Cellulose reacted with carboxylic acids using classic peptide coupling reagent, DCC, in nonaqueous solvents (e.g., DMA/LiCl) to give derivatised polysaccharides with low DS values. Starch was acylated under similar conditions by the in situ activation of carboxylic acids with TsCl or CDI (carbonyldiimidazole) .
The acetylation of alginates was less straightforward than for neutral polysaccharides . The solubility of alginates can be changed by changing the ionisation state (i.e., acid versus salt) and (for the salt form) the counterion [e.g., sodium versus tetrabutylammonium (TBA)]. TBA-alginates were soluble in DMSO/TBAF, but DMA/LiCl did not dissolve either the acid or salt (Na or TBA) forms. When the alginate solution was treated with Ac2O and pyridine, only low DS of up to ca 1 were obtained. It is worth mentioning here that DMSO can react with acylating agents to generate a Swern-type oxidant that can destructively oxidise polysaccharide hydroxyl groups.
In a method for the selective O-acylation of chitosan , the polysaccharide was suspended in water, and a carboxylic acid (C2–C9 as well as some halogenated or unsaturated acids) and H2SO4 (2 M) were added at room temperature. The mixture was then stirred at 80°C for 4 h, and the products (with low DS values of 0.02–0.2) were purified by pH adjustment, precipitation from acetone, and Soxhlet extraction. Under these conditions, the nucleophilicity of the nitrogen is blocked by protonation.
(2) Heterogeneous Reactions. In a heterogeneous reaction, the starting polysaccharide is insoluble in the reaction solvent. But then dissolution may or may not occur during the course of the reaction; only surface groups may be acylated, or alternatively bulk hydroxyls may also react (due to solvent swelling of the material); the macroscopic structure of the material may be retained after derivatisation (fibre, paper, cloth, or nanofibrils, etc.).
Heating a suspension of insoluble cellulose in a mixture of pyridine and acylating agent (5 equiv./Glc = 1.3 equiv./OH) can give acylated celluloses with some acylating agents after purification by precipitation from water . Polysaccharides with DS values of 2.6–2.9 were obtained with acetyl chloride and with long-chain acyl chlorides (>C10) after 3 h. With pivaloyl chloride, a much longer reaction time was required to obtain a product with DS = 2.5 in low yield, and with shorter chain acyl chorides (<C6), decomposition was seen. A similar synthesis of cellulose esters was reported from a suspension of the polysaccharide in pyridine and the acid chloride [39, 40], while initially heterogeneous cellulose reacted with acetyl chloride without added base to give cellulose acetates with DS values of up to 2.96 .
Konjac glucomannan was acylated with palmitoyl chloride and pyridine in benzene in a heterogeneous reaction in which the polysaccharide dissolved during the course of the reaction to give a product with DS up to 2.7 . Arabinoxylan was fully esterified under Fischer conditions by suspending the polysaccharide in a carboxylic acid anhydride (acetic, propionic, butyric) and treating with catalytic methanesulfonic acid . Also here, the polysaccharide dissolved during the course of the reaction. Mixed anhydrides generated from a carboxylic acid and other more reactive acids (e.g., trifluoroacetyl) have also been used as acylating agents with polysaccharides under heterogeneous conditions .
2.2.2. Sulfonate Esters
Sulfonate esters can act as leaving groups in SN2 reactions (see below), and many of their applications derive from this aspect of their reactivity. They may be introduced with reasonably good regioselectivity for the primary hydroxyl groups, and regioselective sulfonate syntheses are described in the section on regioselective reactions (see below). But polysaccharide sulfonates with DS >2 are also accessible. The most commonly seen sulfonates in polysaccharides are toluenesulfonates (tosylates, Ts) and methanesulfonates (mesylates, Ms) .
The classic reaction conditions for tosylate formation involve heating the (initially heterogeneous) polysaccharide with tosyl chloride in pyridine. Three possible side reactions that may occur during sulfonate ester formation, all arising from nucleophilic displacement of the formed sulfonate ester are as follows: (i) cyclisation by attack of one of the secondary hydroxyl groups (e.g., O-3); (ii) attack by pyridine to form a C-6 pyridinium salt; (iii) attack by chloride to form a C-6 chloride. These side reactions are a result of the long reaction times and high temperatures required for the heterogeneous reaction.
Thus, these side reactions can be minimised or suppressed by using homogeneous conditions . Tosylation and mesylation reactions of cellulose in solution in DMA/LiCl gave uniform and well-defined products with DS values between 0.4 and 2.3. The tosylation of cellulose underhomogeneous conditions in the ionic liquid [amim]Cl was also recently achieved .
Sulfonate esters of other polysaccharides have also been synthesised. Chitin was tosylated under homogeneous conditions in DMA/LiCl , dextran tosylates were prepared in organic solvent without any added salt , and konjac glucomannan was tosylated to give products with DS of up to 2.3 . The mesylation of cross-linked particles of pullulan has been reported .
2.3. Regioselective Etherification and Esterification of Polysaccharides
The primary alcohol of a saccharide will, with very few exceptions, always be more nucleophilic than the secondary alcohols. The difference in reactivity between the primary and secondary alcohols can vary, though, and complete regioselective distinction between primary and secondary alcohols (i.e., normally C-6 versus all of C-2, C-3, and C-4) will often not be seen. The respective rate constants for the substitution of primary and secondary alcohols do not change during a reaction, and if a primary alcohol reacts more quickly than a secondary alcohol, its concentration will decrease more rapidly as the reaction progresses. Therefore, as the reaction progresses, the rates of reaction of the primary and secondary alcohols will become similar and regioselectivity will decrease.
Differentiation between the nucleophilicity of the different secondary hydroxyl groups in a polysaccharide will often be difficult or impossible, and polysaccharides containing different substitution patterns may often be formed. Having said that, there are a few examples of regioselectivity between the secondary positions of polysaccharides that can be exploited synthetically. The regioselective protection of cellulose, focussing on ether and ester protecting groups has been reviewed  and covered to some extent in other reviews [49, 50].
The hydroxyl groups of cellulose are much more reactive in solution than they are in the solid phase, because when cellulose dissolves, the extensive hydrogen-bonding network is broken up. As a result, reactions in solution can be carried out under milder conditions than in the solid phase, and this allows a higher degree of selectivity. Thus, regioselective derivatisations of cellulose and other polysaccharides are generally carried out under homogeneous reaction conditions, and the solvent system DMA/LiBr (or LiCl) is often used.
Only a rather limited number of groups/transformations live up to the very high regioselectivity criteria that are necessary for the modification of polysaccharides. These include the installation of trityl ethers (at O-6) and of bulky silyl ethers (at O-6 or at both O-2 and O-6). The installation of carboxylate esters (at O-6, but not normally selective enough) and tosylate esters (at O-6, but not normally completely selective, or at O-2) are also considered here. The installation of halides at C-6 in a phosphane-mediated reaction is also often a regioselective process, but this in this reaction, the polysaccharide behaves as an electrophile, so it is considered in a later section of this review.
2.3.1. Trityl Ethers
The trityl group reacts with cellulose preferentially at the primary hydroxyl, O-6, on steric grounds (Scheme 1). Trityl ethers may be installed by heating cellulose (rayon) with pyridine and trityl chloride (i.e., under initially heterogeneous conditions with dissolution occurring as the reaction proceeds), and DS values close to 1 with little substitution of the secondary positions are obtainable [26, 51]. Cellulose has also been tritylated under homogeneous conditions to give products with DS values of 1.0 . The solvents used were DMSO/N2O4; DMA/LiCl; or DMSO/SO2/DEA.
6-O-Trityl derivatives of some other polysaccharides have been prepared, directly or indirectly. Amylose underwent tritylation regioselectively at O-6 uneventfully . Chitin was also tritylated regioselectivity with reaction at O-6 . β-Chitin was suspended in pyridine and heated at 90°C for 72 h with trityl chloride (10 equiv.) and DMAP (3–6 equiv.). Products with DS values of 0.75–1.0 were obtained by purification by precipitation from methanol. A 6-O-trityl derivative of chitosan was prepared by a three-step sequence. First, the nitrogen was protected as a phthalimide derivative, then O-6 was tritylated, and finally N-deprotection gave the 6-O-tritylchitosan with DS = 1 .
2.3.2. Silyl Ethers
Thexyldimethylsilyl chloride (TMDSCl) has been shown to react with cellulose with very good regioselectivity, and different regioselectivities, O-6 only or for both O-2 and O-6, are seen under different reaction conditions (Scheme 2). Treatment of cellulose (undissolved, i.e., under initially heterogeneous conditions) with TMDSC1 in DMF saturated with ammonia at –15°C resulted in the introduction of TMDS groups at C-6 only, with a DS of 0.99 . When the reaction was carried out under homogeneous conditions in DMA/LiCl and with imidazole as base, 2,6-di-O-thexyldimethylsilylcellulose was formed with a DS of 2.0 [55, 56]. Moreover, this 2,6-protected derivative can be used for the regiospecific introduction of substituents at O-3 of cellulose. 3-O-Methylcellulose and 3-O-allylcellulose have been synthesised in this way. The silyl ethers can be removed by treatment with TBAF (tetrabutylammonium fluoride). Liquid ammonia has also been used as an effective solvent for silylation reactions of cellulose .
2.3.3. Carboxylate Esters
Regioselectivities (for O-6) are generally lower for carboxylate esterification reactions of cellulose than those seen for the formation of trityl ethers or silyl ethers . An investigation of various sterically hindered acylating agents, including pivaloyl chloride, adamantoyl chloride, and 2,4,6-trimethylbenzyl chloride, in solvents including DMA/LiCl, DMSO/TBAF, and the ionic liquid [amim]Cl, failed to give satisfactory regioselectivity . But having said that, in a different study, excellent regioselectivity for O-6 of cellulose was observed in an esterification reaction using benzyl chloride in [amim]Cl without any added base .
It is relevant in this context to note that silyl ether protection may be regiospecifically replaced by carboxylate protection . When a cellulose derivative bearing trimethylsilyl ethers is treated with an acyl chloride in the absence of a base, the silyl ethers are regiospecifically replaced by acyl groups (in the presence of a base, the silyl ethers remain, and the free hydroxyl groups are acylated). But while this process is well known for trimethylsilyl ethers, it has apparently  not yet been investigated for thexyldimethylsilylethers, which (as described above) can be introduced into cellulose with excellent regioselectivity.
2.3.4. Sulfonate Esters
Cellulose reacts preferentially at O-6 in tosylation reactions (see above), but the regioselectivity is not perfect. The esterification of cellulose with various sulfonic acid chlorides, including the 2,4,6-trimethylbenzenesulfonyl group, under homogeneous conditions (in DMA/LiCl), was investigated in an attempt to improve the regioselectivity for substitution at O-6 , but in general, the products contained mixtures of 2- and 6-tosylation.
A very interesting result has been obtained concerning the regioselectivity of the tosylation of starch. When starch (70% amylose) was tosylated in solution in DMA/LiCl, O-2 reacted preferentially, with very good regioselectivity (over O-3 and O-6), to give a product with a DS ≈ 1, with the tosyl groups essentially exclusively at C-2. The regioselectivity was proved by 1H and 13C NMR spectroscopy (Scheme 3) . This regioselectivity is counterintuitive, and apparently, it is also solvent-dependent: Horton had previously reported that when the tosylation of amylose was carried out in pyridine, the more expected product, 6-O-tosyl-amylose, was formed with DS ≈ 0.6 (Scheme 3) .
Inulin was tosylated by treatment with TsCl and Et3N, in DMF/LiCl at 0°C. Purification by precipitation then dialysis gave a polysaccharide product derivatised at O-6 and with some partial derivatisation at O-4 .
2.4. Enzymatic Reactions: Regioselective Esterification and Deesterification
In general, regioselectivity in chemical reactions is controlled by a combination of steric, electronic, and stereoelectronic factors. In enzymatic reactions in contrast, the reaction will occur at the position that is held close to the relevant catalytic amino acid side chains when the substrate is bound in the active site of the enzyme. That is true at least when the substrate of the reaction is the same as, or close in structure to, the natural structure that the enzyme has evolved to modify, for example, for galactose-6-oxidase and galactose (see below). Some enzymes, though, have broad substrate tolerance and catalyse reactions on rather generic structures. When esterases, lipases, and proteases are used to catalyse the formation and hydrolysis of esters on polysaccharides in the laboratory, this is not the natural function of the enzyme, so they have not evolved to differentiate the different hydroxyl groups. Rather, in these enzyme-catalysed reactions, the enzyme will tend to act on the hydroxyl group (for esterification) or ester (for hydrolysis) that is most sterically accessible, i.e., those at the primary positions. Hence in principle, 6-monoesters may be accessible by enzyme-catalysed regioselective acylation of an unprotected polysaccharide, and in principle, 6-mono-unprotected polysaccharides may be accessible by peracylation followed by regioselective hydrolysis of the primary esters.
The considerations regarding solvents for enzyme-catalysed reactions can be summarised briefly as follows. Enzymes normally require at least a trace of water to function properly, and they may also be structurally unstable in nonaqueous media. However, water is not a good solvent for acylation reactions, as the enzyme-catalysed reactions are reversible. When water is present in excess (i.e., as solvent), the equilibrium would lie towards hydrolysis, so the DS values of the products would be very low. Polar solvents (e.g., DMF, DMSO, etc.) can strip the essential catalytic water from the surface of enzymes, rendering them inactive. Solvents with lower hydrogen-bonding ability will thus be more likely to lead to higher enzyme activity, but those with a better hydrogen-bonding ability would better dissolve the polysaccharide substrates. Thus, in choosing a solvent, a balance must be struck between dissolving the substrate and maintaining the activity of the enzyme [4, 65].
Nonpolar solvents are not ideal, as the enzyme and the substrate are insoluble, and insoluble enzymes cannot catalyse reactions on insoluble substrates. But enzymes can be made soluble in nonpolar solvents by micelle formation, or they can be made accessible by immobilisation in the pores of a solid surface (as in Novozyme, i.e., immobilised Candida antarctica lipase B).
2.4.1. In Nonpolar Solvents
In a pioneering approach to the enzymatic modification of solvent-insoluble polysaccharides in organic solvents , a method was developed to use surfactants to solubilise enzymes in organic solvents. In this way, insoluble amylose could be acylated with a protease from Bacillus subtilis (Subtilisin Carlsberg) using vinyl caprate as acyl donor in isooctane as solvent. As the starting polysaccharide is completely insoluble in the very nonpolar solvent, only surface-accessible hydroxyls could be acylated, and the authors estimated that >90% of the surface-accessible primary hydroxyls were esterified. This corresponded to DS values of ca 0.15 and 0.30, respectively, for a thin amylose film and a milled amylose powder. Subsequently, the enzymatic esterification of various solid celluloses was addressed, including cloth, thread, paper, and milled particles . The cellulose samples failed to react in isooctane, but esterification did occur in pyridine when the Subtilisin Carlsberg (protease) was transferred into that more polar solvent, presumably due to better preswelling of the cellulose.
In a related approach, the enzymatic acylation of starch in toluene was achieved by coating polysaccharide nanoparticles in surfactant . “Reverse-micelles” were formed with the starch particles and the surfactant in octane, and then the octane was removed. These surfactant-coated particles then underwent acylation in toluene at 60°C with immobilised C. antarctica lipase B (i.e., Novozyme 435), using vinyl esters or acid anhydrides as acyl donors. A DS of up to 0.9 was obtained with acylation occurring regioselectively at O-6. Nanoparticles have a high surface area/volume ratio, which allows efficient derivatisation of a heterogeneous system.
2.4.2. In Water
Enzyme-catalysed esterification reactions are reversible, so in water, the DS values of the products will tend to be very low. The esterification of starch in water using decanoic acid as acyl donor, catalysed by a lipase from Thermomyces lanuginosus, was reported. Only very low DS (=0.018) was obtained . The authors compared different methods of measuring the DS, including the classic titrimetric method (saponification followed by back titration) and NMR and FT-IR based methods, and proposed a new method based on ester hydrolysis followed by GC analysis. The acetylation of (insoluble) cellulose in water using vinyl acetate as the acyl donor, catalysed by a lipase from Aspergillus niger, was reported. But here again, only very low DS values were seen (quoted as 0.16% by weight) [70, 71].
2.4.3. In Polar Aprotic Solvents
A series of papers describe the lipase-catalysed esterification of starch with fatty acids, either in polar aprotic solvents (DMSO or DMF) or under solvent-free conditions with microwave heating. The esterification of starch was investigated using lipases from Thermomyces lanuginosus , Burkholderia cepacia , and Candida rugosa . Carboxylic acids obtained by the hydrolysis of coconut oil were used as acyl donors. Both neat (DS = 1.0–1.5) and solution (DS = 1.0–1.45) methods resulted in significant esterifcation of the starch, except for when T. lanuginosus was used in solution in DMSO, when only a low DS (0.08) was obtained.
The free hydroxyl groups of cellulose acetate were acylated using Novozyme (immobilised Candida anctarctica lipase B) in acetonitrile .
2.4.4. In Ionic Liquids
Ionic liquids might seem to be a promising candidate for this transformation, as they can dissolve polysaccharides, and they are good solvents for the regioselective enzymatic acylation of unprotected monosaccharides. When conventional organic solvents are used for the enzymatic acylation of unprotected monosaccharides, the initial reaction products (typically 6-O-acyl derivatives) will tend to be more soluble than the starting material in the reaction solvent and so are more available for further reaction. This can result in overacylation (to give, e.g., 3,6-di-O-acyl derivatives) and mixtures of products. But ionic liquids dissolve the starting monosaccharides, so the reaction mixtures are homogeneous and good regioselectivity results . However, the regioselective enzymatic acylation of polysaccharides in ionic liquids does not appear to have been investigated.
2.4.5. Enzymatic Deesterification of Polysaccharides
An example of the cleavage of esters from 6-O-acyl-cellulose (i.e., only O-6 acylated) using a protease is reported in the literature . Partial hydrolysis occurred in water, and the authors concluded that the more accessible surface esters were cleaved from the heterogeneous (insoluble solid) substrate.
A very interesting development concerns esterases that have naturally evolved to hydrolyse the esters of polysaccharides. Xylan in hemicellulose can be partially substituted by glucuronic acid residues and by acetates. Acetyl xylan esterases are enzymes that hydrolyse these acetates at the 2- and 3-positions of xylopyranose in xylan. Several of these enzymes were screened for cleavage activity of ester groups in partially acetylated celluloses (DS = 0.7 or 1.4), and some of the enzymes showed regioselective behaviour, as shown by 13C NMR spectroscopy . The xylan esterase from Aspergillus oryzae cleanly cleaved the O-2 and O-3 acetates, leaving the O-6 acetate. Other xylan esterases (e.g., from Schizophyllum commune or Aspergillus niger) cleaved the O-2 acetate, leaving the O-3 and O-6 acetates (albeit less cleanly).
3. Saccharide Carbon as Electrophile
The replacement of a saccharide oxygen by a heteroatomic nucleophile in a nucleophilic substitution (SN) reaction typically requires at least two steps. First, a saccharide hydroxyl group must be transformed into a good leaving group, which results in the attached carbon becoming susceptible to nucleophilic attack. Second, treatment with a nucleophile results in attack at the electrophilic carbon of the polysaccharide and displacement of the leaving group.
Saccharide electrophiles are much less reactive towards nucleophilic displacement than their more typical hydrocarbon-derived counterparts. In considering the reactions of polysaccharides, we consider nucleophilic substitution reactions at the primary and secondary positions (but not the anomeric position) of the constituent monosaccharides. In contrast to typical hydrocarbon substrates, saccharides will almost certainly never undergo nucleophilic substitution by an SN1 mechanism at the secondary positions nor at the primary positions. This is because an intermediate carbocation would be strongly destabilised by the multiple electron-withdrawing hydroxyl groups. Hence all nucleophilic substitution at the primary and secondary positions in a polysaccharide will occur by SN2 processes.
Even SN2 reactions are disfavoured in saccharides, at the primary positions, and very much so at the secondary positions. The empirical effect, sometimes called the β-oxygen effect or Oldham and Rutherford’s rule [43, 77, 78], has electronic and steric explanations, which I summarise very briefly here. In an SN2 reaction, electrons must be relocalised onto the departing leaving group, and this aspect of the mechanism is disfavoured by having electron-withdrawing groups in the vicinal positions . Also, the bulk of neighbouring alkoxy or acyloxy groups makes saccharide-derived electrophiles less reactive in SN2 reactions (cf the neopentyl effect in SN2 reactions of hydrocarbons). A further factor that disfavours SN2 reactions at the secondary positions of pyranoses (but not furanoses) derives from the well-known high stability of a six-membered ring in the chair conformation, especially one bearing multiple equatorial substituents. At the SN2 transition state, a ring-conformational change occurs to accommodate the nucleophile and leaving group in the coordination sphere of the central carbon. This ring-conformational change is less favourable in a six-membered ring due to the loss in the stability of the molecule in moving away from a very stable to a less stable ring-conformation.
Thus, SN2 reactions at the secondary positions of polysaccharides are almost unknown, but the fact that they can be achieved in high yields in monosaccharide systems, using good nucleophiles and good leaving groups, means that this could be a possible avenue for future exploration in the synthesis of polysaccharide derivatives. The derivatisation of cellulose by nucleophilic substitution (saccharide electrophile) has been reviewed .
3.1. Installation of Leaving Groups
Leaving groups that are useful at the primary positions include bromide, iodide, less reactive sulfonates, or phosphonium leaving groups generated in situ (in Mitsunobu and related reactions). Leaving groups that are useful at the secondary positions of monosaccharides are triflates and epoxides, but nucleophilic displacement at the secondary positions has hardly been exploited in the polysaccharide series, with only a rare example of a well-defined epoxide-opening reaction by an oxygen nucleophile (see below). Thus, almost all of the nucleophilic substitution chemistry of polysaccharide electrophiles that has been reported to date has taken place at the primary positions.
Hydroxyl groups react with sulfonating agents to generate sulfonate esters. It may be possible to activate the primary alcohol (OH-6) regioselectively, but for more details on this process, see the section above on nucleophilic reactions of polysaccharide hydroxyl groups. The sulfonate group has a general structure RS(O)2O–, and the R group can be varied to tune the electronic properties and thus the reactivity of the sulfonate ester. Despite the almost unlimited possibilities for structural variation here, only a few sulfonates have been in common usage in the nucleophilic displacement reactions of polysaccharides.
Mesylate (methanesulfonate, R = Me) and tosylate (-tolunesulfonate, R = -MeC6H4) have broadly similar reactivities and will normally undergo nucleophilic displacement at the primary positions but not at the secondary positions of pyranosides. When there are free hydroxyl groups at the vicinal positions to tosylates or mesylates at the secondary positions of partially protected monosaccharides or polysaccharides, nucleophilic substitution may take place. Presumably, though, this process goes via epoxide intermediates, as when there is no vicinal alcohol group, there is no substitution reaction. Triflate (trifluoromethanesulfonate, R = CF3) has a strongly electron-withdrawing R group. Consequently, it is a better leaving group, and it can be used in nucleophilic substitution reactions at the secondary positions of monosaccharides, but examples on polysaccharide substrates do not appear to be known.
Halides are the classic leaving groups in nucleophilic substitution reactions, and the displacement of halides from the primary positions (e.g., C-6 of cellulose, amylose, etc.) of polysaccharides has been used to introduce nucleophilic groups (Scheme 4).
One method that has been used for the introduction of the halide leaving groups at C-6 of polysaccharides is the treatment of C-6 sulfonates (including tosylates and mesylates) with halide salts using acetone as solvent (i.e., Finkelstein conditions) . An obvious disadvantage of this approach, though, is that if the halide is to be used as a leaving group in a nucleophilic substitution reaction, it can seem pointless to add an extra step to a reaction sequence when the C-6 sulfonate in the starting material can itself act as a leaving group in substitution reactions with the same nucleophiles.
Thus, methods for the preparation of polysaccharide halides directly in one step from the native polysaccharides would appear to be advantageous.
In the monosaccharide series, several sets of mild reaction conditions based on treatment with PPh3 together with a halide source that can be reduced (e.g., CBr4 in the Appel reaction, I2 in the Garegg reaction, etc.) have been developed for the regioselective preparation of bromides or iodides from the unprotected glycosides. Under these mild reaction conditions, the primary alcohol reacts regioselectively, and the secondary alcohols remain untouched .
Polysaccharides may also be halogenated directly and regioselectively under related phosphane-based conditions, or using classical halogenating agents such as SOCl2, without initial protecting-group manipulations. In cellulose, C-6 is halogenated first, and C-3 may also be halogenated under certain conditions, while C-2 does not normally react . In chitin, C-6 may be halogenated, while C-3 does not react. Thus, chitin may be transformed into a polysaccharide containing three different functional groups, halogen, alcohol, and amide, in a single step.
Cellulose could be chlorinated with the classical chlorinating agents, thionyl chloride and mesyl chloride (MsCl), to give polysaccharides with DS values of up to 2.8, meaning that almost complete chlorination had occurred at both primary and secondary positions . However, significant depolymerisation was also observed under these conditions. The reagent system of N-chlorosuccinimide (NCS)/PPh3/LiCl in DMA was more regioselective for the chlorination of cellulose.
Several other polysaccharides were chlorinated with good regioselectivity for the primary positions using MsCl, including amylose (in DMF/LiCl) , inulin (in DMF, 70°C, 16 h) , and pullulan (in DMF) .
The chlorination of chitin using sulfuryl chloride was investigated . With this reagent, reaction at C-6 was seen at low temperatures, and at higher temperatures, C-3 was also chlorinated. Chitin could be chlorinated regioselectively at C-6 using NCS/PPh3 in DMA/LiCl to give a product with a DS of 1.0, but some depolymerisation was seen under these conditions .
The bromination of cellulose could be carried out with the tribromoimidazole/PPh3/imidazole reagent system in DMA/LiBr to give bromocelluloses with DS values of up to 1.6 . Here, bromination had occurred at C-6 and C-3, and the brominated C-3 carbons were found to have a mixture of gluco and allo configurations.
An essentially completely regioselective bromination of cellulose (at C-6) was achieved using N-bromosuccinimide (NBS)/PPh3 in DMA/LiBr, giving a 6-bromo-6-deoxycellulose with DS = 0.9 [87, 88]. The regioselectivity of this bromination reaction can be better than that of a tosylation reaction. This makes phosphane-mediated bromination an attractive method for the very regioselective modification of cellulose (at C-6) ; the analogous direct iodination of unprotected polysaccharides does not appear to be known, however.
Similar bromination reactions of other polysaccharides with the NBS/PPh3 reagent system gave similarly excellent regioselectivity and high degrees of substitution. When amylose was treated with NBS/PPh3 in DMF, only derivatisation of the primary positions was observed , and it was possible to monitor the progress of this reaction by following the development of the NMR spectra. The analogous bromination of chitin was achieved with NBS/PPh3 in DMA/LiBr to give a product with a DS of 0.94, but here some loss in DP was seen . It is possibly relevant that while chitin is soluble in DMA/LiCl, it is not soluble in DMA/LiBr, so this reaction was heterogeneous.
The bromination of curdlan was achieved with a different phosphane-based reagent system, CBr4/PPh3 in DMF/LiCl . The reaction proceeded essentially to completion and with complete selectivity for the primary position (C-6) .
To date, polysaccharide epoxides do not appear to have been widely investigated, but the synthesis of a 2,3-anhydro derivative of cellulose (i.e., a 2,3-epoxide) has been reported (Scheme 5) . First, O-6 was protected as a trityl ether, then O-2 was converted regioselectively into a tosylate. Treatment of this compound with base resulted in attack of O-3 onto C-2, displacement of the tosylate, and closure of the epoxide ring to give a 2,3-anhydro-6-O-tritylcellulose. The DS of this polysaccharide was ca 0.3, as determined from the incorporation of methyl groups after ring-opening by methoxide.
Cyclodextrin (per) epoxides are also known , and they have been synthesised by a similar but possibly more regioselective sequence of 6-O-silylation, 2-O-sulfonation, and base treatment for epoxide closure.
3.2. Nucleophilic Displacement
3.2.1. Oxygen Nucleophiles
Normally, esters or ethers of polysaccharides (or indeed of monosaccharides) would be prepared by the reaction of a saccharide oxygen nucleophile with an alkylating agent or acylating agent (see above). The complementary approach, where the saccharide acts as an electrophile and is attacked by an alcohol (for ether formation) or a carboxylate (for ester formation), is much less common, but examples of this type of derivatisation do exist for polysaccharide substrates.
A situation where the more usual approach of nucleophilic attack by a saccharide oxygen nucleophile would be impossible would be in the synthesis of phenyl ethers. And indeed, a 6-O-phenyl ether derivative of cellulose was synthesised by displacement of a 6-tosylate by phenoxide [93, 94]. Nucleophilic substitution reactions at the secondary positions of polysaccharides are extremely rare, but a 2,3-epoxide derivative of cellulose underwent ring-opening by methoxide in a reaction that was assumed to be quantitative .
Intramolecular O-nucleophilic displacement to give cyclic derivatives is also known. For example, starch was converted into a 3,6-anhydro derivative with a DS of 0.85 using the following sequence: tritylation of O-6, acetylation of O-2 and O-3, detritylation of O-6, tosylation of O-6, and finally deacetylation of O-2 and O-3, which also resulted in intramolecular nucleophilic attack of O-3 onto C-6, displacing the tosylate and cyclisation to form the 3,6-anhydrosugar .
Esterification by this concept has also been reported. Carboxylate salts have been used in nucleophilic displacement reactions with primary amylose halides to give C-6 esters .
Finally, esterification is possible under the conditions of the Mitsunobu reaction, an overall formal condensation reaction between an (unactivated) alcohol and a carboxylic acid nucleophile. The basis of the Mitsunobu reaction is a redox reaction between stoichiometric amounts of an oxidising agent [normally DEAD (diethyl azodicarboxylate; which is reduced to DEAD-H2)] and a reducing agent [normally PPh3 (which is oxidised to Ph3P=O)] that require a mole equivalent of water to allow their reaction. Hence, anhydrous conditions are a prerequisite for this chemistry. The mechanism involves the in situ activation of an alcohol by the generation of a phosphonium leaving group and its subsequent displacement by a nucleophile to give the product. The reaction is related to the phosphane-based halogenation reactions described above.
Mitsunobu reactions at the primary positions of carbohydrates are well known. The reactions are normally high-yielding and regioselective, so it is often possible to refunctionalise the primary position of an unprotected monosaccharide . However, a limited number of reactions of secondary carbohydrate alcohols are known.
Very little has been published on the Mitsunobu chemistry of polysaccharides. However, the reactivity of amylose under the conditions of Mitsunobu esterification has been investigated . Initially esterification occurred regioselectively at C-6, but as the reaction proceeded above DS = 0.5, some esterification of the secondary positions started to be observed.
3.2.2. Nitrogen Nucleophiles
The introduction of different types of nitrogen-containing groups at the primary positions of polysaccharides by nucleophilic displacement has been fairly extensively investigated. Two broad classes of nucleophile can be considered (Scheme 6). Amines will be neutral nucleophiles and will carry one or more alkyl chains that will be retained in the final product. Alternatively, a negatively charged nucleophile such as azide could be used. The azide in the polysaccharide product could then be reduced to reveal an amine that could be further functionalised if desired. The monovalent nature of an azide nucleophile can have the advantage of avoiding possible multiple substitution of amine nucleophiles that would lead to cross-linking and complex product mixtures .
A synthesis of 6-amino-6-deoxycellulose (DS = 1.0) by the essentially uniform introduction of nitrogen at C-6 of cellulose has been described . Tosylation of cellulose resulted in complete derivatisation of O-6, but the reaction was not completely regioselective, and significant tosylation of O-2 and O-3 also occurred. This polysaccharide was then treated with azide. The C-6 tosylates were substituted, but the secondary tosylates did not react. Treatment with LiAlH4 reduced the C-6 azides to give C-6 amines and, at the same time, reductively cleaved the 2- and 3-tosylates to give the final product. The displacement of the C-6 tosylate by azide was carried out in DMSO at 50°C. When higher temperatures (100°C) or an acetone/water solvent were used, some introduction of azide at C-2 or C-3 was also seen (possibly via epoxide intermediates, see above).
An alternative approach to 6-amino-6-deoxycellulose going via the C-6 bromide, which can be formed from cellulose more regioselectively than the C-6 tosylate, has been published . Thus, bromination of cellulose followed by azide displacement and reduction gave 6-amino-6-deoxycellulose with very clean 13C NMR spectra (DS = 0.96) in only three steps. However, some depolymerisation occurred (the Avicel microcrystalline cellulose starting material had DP = 114; product DP = 66). But when microwave irradiation was used for heating, the reaction times could be shortened, and the degradation minimised (starting DP = 114; product DP = 106) .
Primary halides or tosylates of several other polysaccharides have been shown to undergo nucleophilic displacement by azide. 6-Azido-6-deoxyamylose was prepared from the corresponding amylose bromide (sodium azide, DMSO, 50°C, 6 h) or chloride (sodium azide, DMSO, 70°C, 65 h ). As expected, the bromide was much more reactive than the chloride. Similarly, a starch tosylate reacted with sodium azide (DMF, 100°C, 24 h) to give a starch azide with a DS of 0.96 .
Treatment of 6-bromo-6-deoxycurdlan (DS ≈ 1) with azide gave complete substitution, as judged by the very clean 13C NMR spectrum of the product . The introduction of azide into phthalimide-protected chitosan was achieved by displacement of both tosylate and bromide leaving groups . The reaction of tosylates of lichenan, pullulan, and dextran with an azide nucleophile was investigated . Heating with sodium azide in DMF (24 h, 100°C) resulted in higher degrees of substitution of tosylate by azide (67–75%) for the tosylates of lichenan and pullulan than for the tosylate of dextran (45%), probably because the number of primary tosylates in dextran [predominantly a (1–6)-linked polymer] is lower. Azide substitution of a 6-chloro-6-deoxypullulan (NaN3, water, 100°C)  and of tosyl or chloride derivatives of inulin (NaN3 in DMSO)  has also been reported.
The direct introduction of azide into unprotected polysaccharides in a phosphane-based process related to the Appel, Garegg, and Mitsunobu reactions discussed above offers an advantageous straightforward one-step route to 6-azido-6-deoxy derivatives of some polysaccharides (Scheme 7) . Amylose or pullulan could be treated with PPh3/CBr4 in DMF/LiN3 under homogeneous conditions at room temperature to readily give the C-6 azides regioselectively. This procedure was extended to starches, replacing LiN3 by the more easily available NaN3, and using either DMF or DMA as solvent . Native starches failed to react unless their granular structures were disrupted, in which case full conversion was seen. With amylose or amylopectin starches, when NaN3 (2 equiv.) was used and the reaction was run at 100°C for 1 h, essentially homogeneous incorporation of azide at C-6 (DS = 1) was observed; no evidence of substitution at C-2 or C-3 could be seen.
The functionalisation of cellulose derivatives (but not other polysaccharides) using amine nucleophiles has also been investigated. The reaction of tosylated cellulose with methylamine was studied in detail [typical conditions: DMA, MeNH2 (aq., ca 40 equiv.), 60°C, 48 h; purification by precipitation] . The nucleophilic substitution reaction occurred only at C-6, and conditions were found that allowed the preparation of a polysaccharide with DSN of ca 1, but presumably some unreacted tosylate groups remained at the secondary positions of this product.
Similarly, the reaction of tosylated cellulose (DStotal ≈ 2; DSC-6 = 1.0) with butylamine was studied under different conditions . The reaction proceeded much more quickly (and regioselectively for C-6) in neat butylamine (neat BuNH2, 50°C, 24 h) than it did in DMSO solution (DMSO, BuNH2 (ca 5 equiv.), 75°C, 24 h). It has also been shown that bromide can be an effective leaving group in such reactions, as 6-bromo-6-deoxycellulose (DS = 0.92) reacts with amines in DMSO at 90°C to give, after purification by precipitation and dialysis, polysaccharide amine products with DSN ≈ 0.9 . Finally, tertiary amines have been shown to react with tosylated cellulose to give ammonium salts .
3.2.3. Sulfur Nucleophiles
The introduction of sulfur nucleophiles into polysaccharides (cellulose and starch) has been the subject of some research (Scheme 8), albeit to a much lesser extent than for nitrogen nucleophiles.
Thiols were used as nucleophiles in nucleophilic substitution reactions with 6-bromo-6-deoxycellulose (RSH; R = Me, Ph, CH2CH2OH, CH2CH2NH2, etc.) under heterogeneous conditions in aqueous sodium hydroxide, giving a maximum conversion of 65% . When the pH was too basic, 5,6-elimination and 3,6-cyclisation competed with the SN reaction. A similar reaction between a 6-bromo-6-deoxycellulose and thiols was also carried out under homogeneous conditions in DMA/LiBr, using triethylamine as base, followed by purification by precipitation or dialysis . A detailed optimisation of the conditions for this reaction was undertaken. 6-O-Tosyl-cellulose has also been used as an electrophile in a thioether-forming reaction with sodium methanethiolate (DMF, 0°C, 8 h) .
Other sulfur nucleophiles have been used in reactions with polysaccharide electrophiles for the indirect synthesis of polysaccharide thiols. 6-Bromo-6-deoxycellulose (DS = 0.85) was converted into the thiol in a two-step process. First, sulfur was introduced using a thiourea nucleophile (DMSO, 70°C, 48 h) . The initial product, a (poly)thiouronium salt, then underwent hydrolysis to give the polysaccharide thiol. Alternatively, 6-bromo-6-deoxycellulose (DS = 0.92) underwent substitution with potassium thiocyanate (DMF, 150°C, 2 h) . Purification by precipitation and dialysis gave a product with DSSCN = 0.88 and residual DSBr = 0.02. A 6-deoxy-6-thio derivative of amylose with DS = 0.8 could be prepared similarly. Thus, 6-O-tosyl-amylose (or alternatively 2,3-di-O-phenylcarbamoyl-6-O-tosyl-amylose) underwent a nucleophilic substitution reaction with KSCN, and then the thiocyanate product was reduced (and the 2,3-protection cleaved) by treatment with LiAlH4 . Xanthates were used as nucelophiles in reactions with tosylates of starch (DS < 0.2), and the products were reduced to give the polysaccharide thiols . Here, though, the conversion of the tosylates in the nucleophilic substitution reaction was not complete, and some formation of thioether linkages was observed.
A heterogeneous reaction in which sulfur nucleophiles were bonded to Whatman filter paper was carried out by initial chlorination followed by nucleophilic substitution by treatment with thiourea or cysteine in suspension in a DMF/water mixture .
It is perhaps worth noting that in monosaccharides, the introduction of thiol nucleophiles at the secondary positions of pyranosides by triflate displacement is relatively trivial , but related work has not been done to date in polysaccharides. Also in monosaccharides, selenoethers have been introduced in a protecting-group-minimised approach, similar to those described here for thioethers . But again, no related work with selenium nucleophiles appears to have been done to date in the polysaccharide series.
Polysaccharides may be oxidised in different ways to produce structures of different types (Scheme 9). Where there is a free primary alcohol (e.g., at C-6 in cellulose or amylose), this may be oxidised simply to give the aldehyde or further to the carboxylic acid level. Oxidation to the carboxylic acid level would result in a polysaccharide based on uronic acids, which would then resemble the structure of natural polyuronic acids such as pectin or alginates. Chemical and enzymatic methods have both been used for oxidation of the primary alcohols of polysaccharides. An alternative mode of oxidation would be the oxidative cleavage of 1,2-diols. Where this structural motif occurs in a polysaccharide (e.g., at C-2 and C-3 in cellulose, amylose, or xylose) it may be possible to undergo a ring-opening oxidative C–C bond cleavage to give dicarbonyl compounds. With these different possible oxidation modes come issues of selectivity—when carrying out an oxidative derivatisation of a native (unprotected) polysaccharide, it would be desirable to have either one of these oxidation modes operating but not both. When oxidising primary alcohols, it may also be desirable to avoid potential simple oxidation of unprotected secondary alcohols to give ketones and also to be able to choose conditions that result in either oxidation to the aldehyde or the carboxylic acid levels. The periodate oxidation of polysaccharides  and the oxidation of cellulose have recently been reviewed .
4.1. Oxidation of Primary Alcohols
A method that has been used for the oxidation of C-6 of monosaccharide glycosides to the uronic acid level is treatment with oxygen over a heterogeneous platinum metal surface as a catalyst . In many respects, this is an attractive method, since molecular oxygen is used as the oxidising agent, water is the sole by-product, and in principle, heterogeneous catalysts can be easily recovered and reused. However, this method has a significant disadvantage when it comes to the oxidation of polysaccharides: as the catalyst is heterogeneous, the degree of oxidation (DSox) can be quite low . It is generally true that homogeneous catalysts will give better results for the modification of insoluble polymeric substrates. Nevertheless, inulin with a DP of ca 30 could be oxidised to the uronic acid level at the primary positions (C-6) with a DSox of ca 0.20 under such conditions , and C-6 oxidation of a galactan over platinum to the uronic acid level with a DSox of ca 0.15 has also been achieved [121, 122, 124]. Purification was carried out by precipitation followed by membrane filtration.
In the early 1990s, Van Bekkum found that a homogeneous catalyst, TEMPO [i.e., (2,2,6,6-tetramethyl-piperidin-1-yl) oxyl], could be used for the regioselective oxidation of the primary alcohols in polysaccharides (starch and inulin were included in the initial report) to give the corresponding polyuronic acids with essentially complete conversion, (i.e., DSox ca 1.0) .
In a typical oxidation procedure , the polysaccharide (20 mmol Glc units), a catalytic amount of TEMPO (0.65 mol-%), and NaBr (0.4 equiv.) were dissolved in water. A pH-adjusted solution of the stoichiometric oxidant, NaOCl (1.1 equiv.), was added at 0°C. The reaction mixture was kept at 0°C, and the pH was kept at ca 10 by the addition of NaOH. The reaction was complete after 1-2 h, after which EtOH was added to quench the reaction and to precipitate the polysaccharide, which could then be collected by filtration. The products were the sodium salts of the polyuronic acids.
The method is catalytic in TEMPO and is selective for primary alcohols, with secondary alcohols remaining unaffected. In the reaction mechanism, the persistent radical TEMPO is initially oxidised to give the active oxidant, an oxoammonium species.
This species then oxidises the polysaccharide primary alcohol to the aldehyde, being itself reduced to the hydroxylamine. The polysaccharide aldehyde must then be hydrated, and the hydrate is then oxidised to the acid by a second molecule of the oxoammonium reagent. The stoichiometric oxidant is NaOCl/NaBr, NaOBr, or NaOCl, and this is responsible for the initial oxidative activation of TEMPO and the subsequent reoxidation of the hydroxylamine to the active oxoammonium species.
This method was suitable for the very selective oxidation of C-6 of soluble potato starch and of pullulan . The three Glc(A) environments of the oxidised pullulan can be clearly seen and distinguished in the 13C NMR spectra of the product. The selectivity for the primary alcohols was estimated to be >95%.
Amylodextrin, which is a short amylose structure with a DP of ca 20, was oxidised selectively at C-6, but some overoxidation at the reducing ends became significant at the shorter polymer chain length . Dextran, which is basically a (1–6)-linked polymer without free primary hydroxyl groups except for end-groups, was oxidised only at the level of background oxidation of the secondary alcohols by NaOCl (or NaOBr), which occurred much more slowly than the TEMPO-catalysed oxidation of the primary alcohols . Apparently, the selectivity for the primary alcohols was less good in inulin, based on furanoside residues, but when the reaction was quenched after 20 min, the a 13C NMR spectrum of the product was clean  and >90% selectivity was reported.
Water-soluble polysaccharides were investigated initially, but this C-6 oxidation to the carboxylic acid (carboxylate) level greatly increased the water solubility of the polysaccharide products, and in fact, the method was found to be broadly applicable. The polysaccharides that have been successfully oxidised using the TEMPO method include starch [125–127], amylose , amylopectin , amylodextrin , dextran , regular comb dextran , pullulan [126, 127], alternan , inulin , chitin [127–129], chitosan [127, 128], and cellulose [127, 128]. Normally, excellent selectivity for oxidation of the primary alcohol was seen, and normally DSox values close to 1.0 (i.e., complete conversion) were obtained . Some reports indicate that the selectivity for the primary alcohols was lower in chitin, and some oxidation of secondary alcohols also occurred , while others found that chitin could be oxidised to give a polyuronic acid with a quite clean 13C NMR spectrum .
The oxidation of cellulose by the TEMPO method has been studied in detail . Different celluloses were investigated, including microcrystalline cellulose (DP = 200), linters (DP = 800), bleached kraft pulps (DP = 900–1200), and amorphous regenerated celluloses. The oxidation procedure was essentially identical to that described above, except that all of the celluloses were, of course, initially insoluble in the aqueous reaction medium. When the oxidation was complete, the polysaccharide had dissolved and purification could be carried out again by precipitation from EtOH. The regenerated celluloses were completely oxidised at C-6 within 2 h, whereas the native celluloses did not form homogeneous solutions, even after long reaction times, presumably due to the crystallinity and the resulting inaccessibility of some of the C-6 hydroxyl groups. When the native cellulose samples had been mercerised, they underwent rapid oxidation. An essentially completely regioselective (C-6) oxidation of these insoluble polysaccharides (i.e., the regenerated or mercerised cellulose samples) was achieved under these conditions, as shown by the 13C NMR spectra of the products.
It was found that under these reaction conditions, some depolymerisation occurred, presumably by a E1CB elimination mechanism across C-4–C-5; the reaction time, temperature, and amounts of reagents are all important factors to be considered if this depolymerisation is to be minimized .
A variant of the TEMPO oxidation method in which the sodium bromide is omitted, but still using NaOCl as the stoichiometric oxidant, has been used for the oxidation of potato starch . This variant method gave similar reaction rates and selectivities when the reaction was carried out at room temperature, and when the pH was kept below 9.5.
TEMPO is a persistent stable radical to the extent that it is a commercially available solid. Related methods for the oxidation of polysaccharides using shorter-lived N–O radicals have been investigated briefly. An example of such a method uses catalytic N-hydroxysuccinimide, NaOCl as stoichiometric oxidant, and NaBr . Another related reaction is the oxidation with N2O4 [122, 124, 131, 132]. This reagent oxidises the primary position of carbohydrates regioselectively to give the uronic acids, but the regioselectivity is not perfect, and some oxidation of the secondary positions can take place. Normally then, it is necessary to include a borohydride reduction step after the oxidation to reduce any ketones back to the alcohol level (clearly this would introduce issues of diastereoselectivity and inhomogeneity in the products). Depolymerisation can also occur (by E1CB elimination resulting in chain cleavage at C-4, see above) under the basic conditions of this reaction. The side-reactions that are found with this reagent mean that it is less suitable for the preparation of pure polyglucuronic acid polysaccharides than the other methods discussed here.
4.2. Enzymatic Oxidation
The enzyme galactose-6-oxidase (EC 184.108.40.206) catalyses the C-6 oxidation of galactose to the aldehyde level, using oxygen as the oxidant and generating hydrogen peroxide as the reduced by-product (3). The reactions are carried out in aqueous solution. Thus, the reaction is complementary to the TEMPO oxidation, where the product of C-6 oxidation is the carboxylic acid rather than the aldehyde.(3)
The enzyme is highly selective for C-6 of galactose, although it does tolerate substituents at the anomeric position of the galactose (i.e., the formation of glycosides). Possible galactose-derived by-products include the uronic acid (from overoxidation) or the α,β-unsaturated aldehyde (from E1CB elimination across C-4–C-5).
The oxidation of polysaccharides with galactose-6-oxidase has been investigated, but first, an optimisation of the reaction conditions was carried out on a monosaccharide model system, methyl α-D-galactopyranoside . The best results were obtained using a combination of three enzymes (viz galactose-6-oxidase, catalase, and horseradish peroxidase) in water rather than buffer. Catalase (EC 220.127.116.11) was added to catalyse the decomposition of the H2O2 formed in the reaction, as otherwise H2O2 can poison the activity of the galactose-6-oxidase. Horseradish peroxidase was added to activate the oxidase enzyme by oxidising it to its active form.
The same group went on to investigate the oxidation of polysaccharides using galactose-6-oxidase in some detail . The general oxidation procedure was as follows: the polysaccharide was stirred in water at 4°C or RT for 1–12 h until it had dissolved. Then the enzymes were added, and the mixture was stirred for 48 h. The oxidation of several galactose-containing polysaccharides was investigated using the same three-enzyme system. These included spruce galactoglucomannan [a β(1–4)-linked backbone of glucose and mannose residues with pendant galactose residues linked α(1–6)], guar gum [a β(1–4)-mannan backbone with pendant galactose residues linked α(1–6)], larch arabinogalactan [a β(1–3)-linked galactan backbone with pendant arabinofuranose units linked α(1–6), and galactose and galactobiose units, linked to the backbone by β(1–6)-linkages], corn arabinoxylan [a β(1–4)-linked xylan with various appendages, mostly arabinofuranose], and xyloglucan from tamarind seeds [a β(1–4)-linked glucan with pendant α(1–6)-linked xylose units; about half of the xylose residues are galactosylated]. Hence the polysaccharides had different galactose contents and different presentations of the galactose units due to branching, and the efficiency of the oxidation reaction varied between the different polysaccharides. Xyloglucan was the most efficiently oxidised (up to DSox 0.8 based on the galactose residues), followed by galactoglucomannan (DSox ca 0.65) and guar gum (DSox ca 0.4; Scheme 10).
There are also some further earlier reports on the oxidation of polysaccharides by galactose-6-oxidase in the literature. The galactose residues in guar gum were converted into the corresponding uronic acids in a two-step process consisting of enzymatic oxidation at C-6 with galactose-6-oxidase, followed by chemical oxidation (with I2/KI) . A synthetic polysaccharide consisting of chitosan to which lactose had been attached by reductive amination was also a substrate for galactose-6-oxidase, and the appended galactose units could be oxidised enzymatically at C-6 . The (1-deoxy-lactit-1-yl) chitosan was dispersed in phosphate buffer to give a soft glassy gel, which was purged with O2 for 1 min. Catalase and galactose-6-oxidase solutions were added and a viscous material formed after a few hours. After 2 d, the mixture was diluted with water, and the polysaccharide was precipitated from absolute ethanol to give a product with a DSox of ca 0.7.
4.3. Oxidative Cleavage of 1,2-Diols
Periodate may be used as an oxidising agent to achieve the ring-opening cleavage of the 1,2-diols at C-2 and C-3 of polysaccharides very efficiently and selectively. The initial product is the dialdehyde and is then usually oxidised further to give the dicarboxylate.
The C-2–C-3 oxidation mode was tested on starch and maltodextrin using different oxidants . Tungstate/H2O2 and hypochlorite both resulted in chain degradation. The best results were obtained using a two-step procedure of periodate oxidation-cleavage (to the dialdehyde) followed by chlorite oxidation (to the dicarboxylate). Under the same conditions, the polysaccharides tested were essentially quantitatively ring-opened to give the polycarboxylate derivatives. It was also confirmed that (as expected) the ring-opened polymers are more susceptible than the parent unoxidised polysaccharides to acid-catalysed depolymerisation (i.e., acetal hydrolysis).
For cellulose, the efficiency of this oxidation reaction may be improved by the addition of metal salts to disrupt intermolecular hydrogen bonding and improve the solubility . Alginates have been subjected to C-2–C-3 oxidative cleavage using periodate . Initially formed aldehyde products were subjected to reductive amination with long-chain alkylamines to give hydrophobically modified derivatives (Scheme 11).
5. Reactions of Carboxylic Acids
Several natural polysaccharides, including alginates and pectins, use uronic acid residues as structural components. In a uronic acid derivative, the C-6 position is oxidised to the carboxylic acid level. This section covers the reactions of these carboxylic acids (Scheme 12), both electrophilic and nucleophilic reactions, including esterification, amide formation, and multicomponent reactions. As well as natural uronic-acid-containing polysaccharides, this chemistry may be applicable to synthetic C-6 oxidised polysaccharides (see above). The modification of the carboxylic acid (uronic acid) functionality of alginates has been reviewed [138, 139].
Carboxylic acids can react either as electrophiles or nucleophiles to form esters. In the first scenario, the acid must first be activated, which may happen prior to the esterification (e.g., by formation of an acid chloride), or in situ by using a coupling reagent such as DCCI, or by using a strong-acid catalyst (Fischer esterification). The activated acid should then be attacked by an alcohol nucleophile to give the ester. However, this approach has some disadvantages that mean it does not appear to have been widely used for the modification of polysaccharide uronic acids: (i) in aqueous solution, the water can effectively compete with the intended alcohol nucleophile, hydrolysing the activated acid intermediates and restoring the carboxylic acid starting material; (ii) where the other hydroxyl groups of the polysaccharide are unprotected, they too could compete as nucleophiles with the added alcohol, and possible cyclised products could result; (iii) in a Fischer (acid-catalysed) esterification, there is significant risk of depolymerisation of a polysaccharide substrate.
In the second approach, the carboxylic acid can be deprotonated by a weak base to generate a carboxylate. This can then react as a nucleophile with alkylating agents to generate the esters. The hydroxyl groups of the polysaccharide will not normally react under these conditions, and so this approach has been more widely used for the preparation of esters of polysaccharide uronates [140, 141].
Treatment of the TBA salt of (completely demethylated) pectin with benzyl bromide and TBAI in DMSO at RT gave the benzyl ester with a DS of up to 0.73 . The decyl ester could be prepared similarly with a DS of up to 0.44. The same method has been used for the preparation of esters of pectin with lower DS (>0.1)  and of alginates and hyaluronates, again with lower DS (>0.1) .
5.2. Amide Formation
Uronic acids must be activated to react as electrophiles with amine nucleophiles to generate amides. Classically, this can be achieved using a coupling (dehydrating) agent such as DCCI or the water-soluble EDCI, but even esters can be used as electrophilic carboxylic acid derivatives in amide-forming reactions.
The conversion of the uronic acids of alginate into amides has been achieved by reaction with amines in water using EDCI, a water-soluble coupling agent . Alginate amides with DS of 0.1–0.3 were synthesised in this way by the reaction of sodium alginate with octylamine and EDCI in water . Purification was achieved by precipitation from EtOH. Alternatively, the reactions could be carried out in an organic solvent. Thus, alginate amides with DS of up to 0.2 were prepared by the reaction of an alginate TBA salt with decylamine and CMPI (2-chloro-1-methylpyridinium iodide; the coupling agent) in DMF . Purification was achieved by ion exchange followed by precipitation from water.
Esters react directly with amines to form amides in a reaction termed aminolysis. In a polysaccharide context, highly methylated pectin (methyl esters; DSmethyl = 0.73) was treated with various alkylamines (n-butyl up to n-octadecyl) in DMF under heterogeneous conditions (8, 25, or 45°C), and the amide products were formed with DSamide = 0.4–0.55 [145–147].
5.3. Other Reactions
Other reactions of carboxylic acids may also be applicable to polysaccharide uronic acids. A concept that has been used to rapidly generate molecular diversity is that of multicomponent reactions [148–151], in which condensation/addition products are generated from three or more starting materials in a single reaction. Carboxylic acids are often found as components in such reactions.
One example is the Ugi four-component reaction between an aldehyde (or ketone), an amine, an isocyanide, and a carboxylic acid to form a diamide [152, 153]. It has been shown that the uronic acids of alginate can undergo the Ugi reaction (Scheme 13) . Thus, an aqueous solution of alginate was treated with formaldehyde, octylamine, and cyclohexyl isocyanide for 24 h. Purification was achieved by dialysis.
6. Saccharide Nitrogen as Nucleophile
This section concerns the reactions of polysaccharide amines such as chitosan, which carries a free basic nitrogen at C-2, but the methods should also be applicable to other synthetic aminated polysaccharides, for example, C-6 aminated cellulose.
Amines can react with electrophiles to give amides (i.e., acylation), higher order amines or ammonium salts (i.e., alkylation), or imines (Schiff bases). The different reactivity of nitrogen and oxygen nucleophiles means that it is often possible to carry out these derivatisations in aqueous solution, and without protection of any free hydroxyl groups in the saccharide derivative. Of course, O-alkylation and O-acylation may take place under some conditions, but with an appropriate choice, it should be possible to find conditions that favour chemoselective derivatisation at nitrogen. (4)(5)(6)(7)
The alkylation of amines can be complex in that the initial products, which are also amines, can react further to form higher order amines or, under direct alkylation conditions, eventually ammonium salts. This can be particularly problematic in direct alkylation reactions with very reactive electrophiles (sterically, e.g., methyl; electronically, e.g., benzyl; or with special reactivity, e.g., allyl) and with reactive nucleophiles. As a result, direct alkylation is not normally used for the preparation of amines, even though when the reactants are more sterically hindered, as is the case with saccharide amine nucleophiles and moderately hindered electrophiles, the barrier to oversubstitution increases.
The reductive amination reaction is widely regarded as the alkylation method of choice for amines. In this method, the amine first condenses with a carbonyl compound (normally an aldehyde) to give an imine. A reducing agent, normally NaBH4, NaCNBH3, or Na(OAc)3BH, reduces the imine to give the amine product. The reaction is best carried out under mildly acidic conditions. Overalkylation can be minimised by this method, but in fact, it is still often seen to a greater or lesser extent (see below). But quaternisation to form ammonium salts cannot occur under these conditions and neither can O-alkylation to form ethers, and these are definite advantages over a direct alkylation method.
6.1. Reductive Amination
Even here, though, overalkylation occurs and products with homogeneous structures are often not obtained. Depending on the ratio of GlcN/aldehyde used, the polysaccharide products were composed of mixtures of mainly monoalkylated and unalkylated glucosamines or mainly dialkylated and monoalkylated glucosamines, according to the 1H NMR spectra of the products . The general procedure is as follows: chitosan was dissolved (i.e., reactions are homogeneous) in either a mixture (1 : 1, pH 5.5) of an alcohol (normally methanol or ethanol) and 1% aq. acetic acid or in 1% aq. acetic acid alone. A solution containing the carbonyl compound and NaCNBH3 (7 equiv.) was added, and the reaction mixture was stirred at room temperature, usually until gel formation was observed (ca 1–24 h). The reaction may be stopped by adjustment of the pH to 10. The solid product is then obtained by filtration and washing with methanol and Et2O. Further purification by Soxhlet extraction into EtOH/Et2O (1 : 1) has also been done in some cases [156, 157]. When no alcohol cosolvent is added, the reaction takes place in essentially aqueous solution. The role of the alcohol is to solubilise the aldehyde component, which can often be hydrophobic.
This procedure has been used with many different carbonyl components, including reducing monosaccharides, disaccharides, ketosugars, other oxidised sugars, and noncarbohydrate carbonyls . Aldehydes bearing straight-chain alkyl groups with chain lengths from C3–C12 have been used . Chitosan underwent N-alkylation under reductive amination conditions with benzylic (heterocyclic) aldehydes: furfural, methylfurfural, pyridine-3-carboxaldehyde, and so forth. The DS of the products was between 0.30 and 0.43, and the broad 1H NMR spectra showed two sets of signals, presumably due to the monoalkylated and the unalkylated glucosamines . Chitosan underwent N-alkylation by reductive amination with aliphatic aldehydes C2–C12 (0.1 to 1 equiv.) to give products with DS between 0.03 and 0.3, and with twelve substituted benzaldehydes (1 equiv.) to give products with DS between 0.2 and 0.5 . A fluorescence label was installed into chitosan by the reductive amination method with 9-anthraldehyde as the carbonyl component, aiming for very low DS (values between 0.00001 and 0.01) .
6.2. Imine Formation
Imines, the C=N intermediates in the reductive amination procedure, are liable to hydrolyse—their formation is reversible. This is clearly a disadvantage when designing a stable product, but in cases where the reversible formation of semistable covalent compounds is beneficial, in supramolecular chemistry, for example, imines can be useful compounds. The conversion of chitosan into imines (without reduction; Scheme 15) has been investigated in solution (to give products with DS of ca 0.9) and under heterogeneous conditions on prespun polysaccharide fibres (to give products with DS of 0.9–1.0) . Typical conditions for imine formation under homogeneous conditions are as follows: chitosan was dissolved in a mixture of 2% aq. AcOH and methanol, and a solution of the aldehyde in methanol was added. This mixture was left overnight, and then the imine (a solid/gel) was then purified by filtration and washing with methanol. Imine formation on prespun chitosan fibres was simply carried out by suspending the fibres in methanol and adding the aldehydes, and after the mixture had been left overnight, the derivatised fibres were washed with methanol.
6.3. Formation of Quaternary Ammonium Salts
Repeated alkylation of the free amine base of chitosan eventually gives quaternary salts (Scheme 16). According to a very recent review covering the formation of quaternary salts (quaternisation) of chitosan , better synthetic routes that do not require the use of dangerous alkylating agents still need to be developed.
Much research into the quaternisation of chitosan has focussed on trimethyl derivatives . In this transformation, the chitosan nitrogen must act as a nucleophile, attacking an alkylating agent (methylating agent) three times. The oxygen nucleophiles in chitosan (i.e., OH-3 and OH-6) could also be alkylated in a potential undesired side process. The pH of the reaction mixture can affect the rate and outcome of the reaction. When no base is added, the basic nitrogens in the starting material and partially alkylated products will be protonated, decreasing their nucleophilicity and resulting in products with low DS. But under basic conditions, O-alkylation could become problematic.
The methylation of chitosan with the aim of tri-N-methylation to form the quaternary ammonium salt without concomitant O-methylation has been investigated in some detail , and errors in a published method  were found. Thus, when alkylation was carried out with MeI and NaOH in 1-methyl-2-pyrrolidinone at 60°C, the major product was found to be the dialkylated product (i.e., the tertiary amine), and significant quaternisation did not occur. A polysaccharide with a DSquat of 0.7 was obtained in a two-step procedure in which the initial product (containing the N,N-dialkylated material as its major component) was isolated and then resubjected to the same reaction conditions. But for higher DSquat values, looking towards complete quaternisation, concomitant O-alkylation started to become significant.
A recent paper describes how a change of solvent can suppress O-methylation, enabling a one-pot synthesis of essentially uniform (DS ca 0.9) quaternised trimethyl chitosan . In this approach, DMF/H2O (1 : 1) was used as solvent, and several separate additions of NaOH and MeI were necessary for complete quaternisation to be achieved. Purification of the products was achieved by precipitation, ion exchange, and dialysis.
A two-step approach to the synthesis of quaternised chitosan using reductive amination followed by alkylation opens the possibility of installing two different R groups onto the nitrogen atoms . The reductive amination procedure was carried out essentially as described above. Subsequently, alkylation was carried out with MeI and NaOH in NMP as solvent, and purification was by precipitation from acetone. The chitosan derivatives obtained by this method were found electrochemically to have DSquat values between 0.8 and 0.9.
6.4. Acylation (Amide Formation)
The acylation of amines to give amides (Scheme 17) is a very well investigated reaction, due to its importance in peptide synthesis. Here, I am covering the reaction of polysaccharide amines with nonpolysaccharide acylating agents to give amides [165, 166]; the related amide-forming reactions between polysaccharide carboxylic acid (uronic acid) derivatives and nonpolysaccharide amines following similar principles are covered above. The reaction may be carried out (in water or alcohol solvents) using acylating agents such as acyl chlorides or acid anhydrides, or using carboxylic acids and dehydrating agents. It can be beneficial to use a reactive O-nucleophile, such as water, methanol, or ethanol, as solvent or cosolvent so as to suppress O-acylation of the polysaccharide, a possible side-reaction that can occur when a polar aprotic solvent (such as DMF, NMP) is used.
Chitosan was N-acylated under homogeneous conditions in solution in 1% aq. AcOH and methanol (1 : 1) using different carboxylic anhydrides as acylating agents . A solution of the anhydride in methanol was added to the chitosan solution, and the reaction was quenched after 15 min by pouring into ammonia solution (7 : 3, v/v). The precipitated polysaccharides were filtered and washed with methanol and ether. The DS values of the products were determined by titration to be <0.5.
Chitosan was also shown to undergo N-acylation under heterogeneous conditions. Fibres of the polysaccharide were suspended in methanol, and a carboxylic acid anhydride (5 equiv.; acetic, propionic, butyric, or hexanoic anhydride) was added. The mixture was shaken at 40°C for 24 h, and then the derivatised fibres were washed with methanol. The DS of the products were between 0.65 and 0.85, as determined by elemental analysis .
7. Unsaturated Derivatives
Polysaccharide derivatives in which the monosaccharide constituents contain C=C double bonds have been prepared. These C=C double bonds represent unusual types of functional groups in polysaccharides.
Cellulose derivatives of this type have been termed cellulosenes , and they should be classified as one of two types-enol ethers or alkenes—depending on whether one of the carbons of the C=C double bond is directly bonded to an oxygen or not (Figure 4). The enol ether and alkene types of unsaturated polysaccharides may be expected to have different properties and reactivities. 5,6-Cellulosene is unsaturated between C-5 and C-6 it is formed by simple elimination (i.e., a formal elimination of water from cellulose), and the C=C double bond is part of an enol ether. In 2,3-cellulosene, unsaturated between C-2 and C-3, the C=C double bond represents an alkene (olefin) functionality and must be formed by a reductive elimination from cellulose.
Some similar unsaturated derivatives of other polysaccharides have been synthesised. Xylan and amylose, two more common (1–4)-linked polysaccharides, have both been transformed into their 2,3-unsaturated olefinic derivatives. The 5,6-unsaturated (enol ether) derivative of amylose has also been investigated—of course, as xylose is built up of pentose monomers, a corresponding 5,6-unsaturated derivative of this polysaccharide cannot exist.
Further possibilities for both the enol ether and alkene types of unsaturated polysaccharide can be envisaged. For (1–6)-linked structures, olefinic unsaturation in the ring could be located either between C-2 and C-3 or between C-3 and C-4, although the regioselective synthesis of such compounds may not be straightforward. In (1–3)-linked pyranose-based polysaccharides, an alkene structure is impossible, as all of C-1, C-3, and C-5 must bear an oxygen atom. (1–2)-Linked pyranose-based polysaccharides are not common.
For both simple elimination and reductive elimination reactions, stereoelectronic factors are important. It will normally be necessary for the two groups that will undergo the elimination reaction to adopt an antiperiplanar or synperiplanar relationship. Free rotation about the exocyclic C-5–C-6 bond should allow a favourable conformation to be reached in the synthesis of 5,6-unsaturated polysaccharides. For the synthesis of compounds with endocyclic unsaturation, though, the stereochemistry of the hydroxyl groups in the pyranose ring can be important.
7.1. 5,6-Unsaturated Derivatives
As stated above, the formal overall process for the synthesis of an enol-ether-based unsaturated derivative of a polysaccharide is elimination of water. For 5,6-unsaturated derivatives this means elimination of water across C-5 and C-6. In a two-step process, OH-6 is converted into a good leaving group, and then treatment with a base will promote the elimination reaction. Processes for the regioselective conversion of OH-6 into a good leaving group are quite well described (see the section on nucleophilic substitution, above). It is well known that nucleophilic substitution reactions can compete with basic eliminations. Such competing processes are typically minimised by using a nonnucleophilic (e.g., sterically hindered) base. However, in polysaccharide systems, when the polysaccharide is unprotected, any base could deprotonate the free hydroxyl groups in the pyranose rings to generate intramolecular nucleophiles that could attack the carbon bearing the leaving group to form a new ring. The undesired intramolecular cyclisation of O-3 onto C-6 in particular has been a problem in the synthesis of 5,6-cellulosene.
A solution to this problem has been reported in a synthesis of 5,6-cellulosene that gave a DS as high as 0.7 (Scheme 18). HI was eliminated from 2,3-di-O-acetyl-6-deoxy-6-iodocellulose by treatment with DBU . DBU is a strong, nonnucleophilic base that is able to induce elimination without acting as a nucleophile on C-6 or removing the acetate protection from O-2 or O-3. The acetates were subsequently cleaved by methoxide treatment to give the unprotected polysaccharide derivative.
7.2. 2,3-Unsaturated Derivatives
2,3-Unsaturated derivatives of the (1–4)-linked polysaccharides cellulose , amylose , and xylan  have all been mentioned in the literature. The stereochemistry at C-2 and C-3 of all these polysaccharides is the same, i.e., trans diequatorial, which means that they may be expected to form 2,3-unsaturated polysaccharides under similar conditions (Scheme 19).
The conversion of amylose into its 2,3-unsaturated derivative was achieved by the following reaction sequence : protection of O-6 as a trityl ether; conversion of O-2 and O-3 into tosylates; reductive elimination with zinc and sodium iodide. Xylan was converted into the corresponding unsaturated polysaccharide following a similar sequence. The reactivity of the alkene functionality was also briefly investigated, undergoing dibromination or hydrogenation .
The number of published methods for the synthesis of alkene-containing polysaccharides by reductive elimination is limited, but studies of similar reactions on simpler monosaccharide systems can be relevant for the further development of this chemistry. A one-step procedure  to convert pyranoside 2,3-diols into alkenes seems particularly relevant. Treatment of the diols with chlorodiphenylphosphine, iodine, and imidazole (reflux, 1 h) gave 2,3-unsaturated derivatives in 75–89% yields starting from glucose (2,3-trans) derivatives, and in 52% yield from a mannose (2,3-cis) derivative. Alternatively, vic-diols were first converted into vic-halocarboxylates, which were then treated with a reducing agent such as zinc [172, 173] or NaSH  to give the alkenes. The reductive elimination step can be easier for furanoside than pyranoside substrates .
8. Concluding Remarks
As well as summarising the achievements in this field, also the gaps are highlighted, and this will hopefully inspire further developments. Many of the methods that have been developed for the modification of polysaccharides are inefficient and wasteful, as stoichiometric amounts of waste products may be formed and several steps may be required. The use of a renewable resource loses a lot of its meaning and significance if it must undergo many manipulations with nonrenewable materials before reaching its final goal. Thus, future research in this area would do well to focus on catalytic transformations.
- M. Yalpani, “A survey of recent advances in selective chemical and enzymic polysaccharide modifications,” Tetrahedron, vol. 41, no. 15, pp. 2957–3020, 1985.
- A. Corma, S. Iborra, and A. Velty, “Chemical routes for the transformation of biomass into chemicals,” Chemical Reviews, vol. 107, no. 6, pp. 2411–2502, 2007.
- S. Van de Vyver, J. Geboers, P. A. Jacobs, and B. F. Sels, “Recent advances in the catalytic conversion of cellulose,” ChemCatChem, vol. 3, no. 1, pp. 82–94, 2011.
- A. G. Cunha and A. Gandini, “Turning polysaccharides into hydrophobic materials: a critical review. Part 2. Hemicelluloses, chitin/chitosan, starch, pectin and alginates,” Cellulose, vol. 17, no. 6, pp. 1045–1065, 2010.
- T. L. Vigo and N. Sachinvala, “Deoxycelluloses and related structures,” Polymers for Advanced Technologies, vol. 10, no. 6, pp. 311–320, 1999.
- T. Heinze and T. Liebert, “Unconventional methods in cellulose functionalization,” Progress in Polymer Science, vol. 26, no. 9, pp. 1689–1762, 2001.
- T. Liebert and T. Heinze, “Interaction of ionic liquids wlth polysaccharides 5. Solvents and reaction media for the modification of cellulose,” BioResources, vol. 3, no. 2, pp. 576–601, 2008.
- M. Gericke, P. Fardim, and T. Heinze, “Ionic liquids-promising but challenging solvents for homogeneous derivatization of cellulose,” Molecules, vol. 17, no. 6, pp. 7458–7502, 2012.
- S. Murugesana and R. J. Linhardt, “Ionic liquids in carbohydrate chemistry-current trends and future directions,” Current Organic Synthesis, vol. 2, no. 4, pp. 437–451, 2005.
- A. W. T. King, J. Asikkala, I. Mutikainen, P. Järvi, and I. Kilpeläinen, “Distillable acid-base conjugate ionic liquids for cellulose dissolution and processing,” Angewandte Chemie International Edition, vol. 50, no. 28, pp. 6301–6305, 2011.
- A. Takaragi, M. Minoda, T. Miyamoto, H. Q. Liu, and L. N. Zhang, “Reaction characteristics of cellulose in the LiCl/1,3-dimethyl-2-imidazolidinone solvent system,” Cellulose, vol. 6, no. 2, pp. 93–102, 1999.
- A. Isogai, A. Ishizu, and J. Nakano, “Preparation of tri-O-benzylcellulose by the use of nonaqueous cellulose solvents,” Journal of Applied Polymer Science, vol. 29, no. 6, pp. 2097–2109, 1984.
- A. Isogai, A. Ishizu, and J. Nakano, “Preparation of tri-O-substituted cellulose ethers by the use of a nonaqueous cellulose solvent,” Journal of Applied Polymer Science, vol. 29, no. 12, pp. 3873–3882, 1984.
- A. Isogai, A. Ishizu, and J. Nakano, “Preparation of tri-O-alkylcelluloses by the use of a nonaqueous cellulose solvent and their physical characteristics,” Journal of Applied Polymer Science, vol. 31, no. 2, pp. 341–352, 1986.
- C. L. McCormick and P. A. Callais, “Derivatization of cellulose in lithium chloride and N,N-dimethylacetamide solutions,” Polymer, vol. 28, no. 13, pp. 2317–2323, 1987.
- L. Petrus, D. G. Gray, and J. N. BeMiller, “Homogeneous alkylation of cellulose in lithium chloride/dimethyl sulfoxide solvent with dimsyl sodium activation. A proposal for the mechanism of cellulose dissolution in LiCl/Me2SO,” Carbohydrate Research, vol. 268, no. 2, pp. 319–323, 1995.
- J. Asikkala, Acta Universitatis Ouluensis 502, 2008.
- M. Söderqvist Lindblad and A.-C. Albertsson, “Chemical modification of hemicelluloses and gums,” in Polysaccharides: Structural Diversity and Function, S. Dumitriu, Ed., p. 491, CRC Press, New York, NY, USA.
- J. N. BeMiller and R. E. Wing, “Methyl terminal-4-O-methylmalto-oligosaccharides,” Carbohydrate Research, vol. 6, no. 2, pp. 197–206, 1968.
- R. Pieters, R. A. De Graaf, and L. P. B. M. Janssen, “The kinetics of the homogeneous benzylation of potato starch in aqueous solutions,” Carbohydrate Polymers, vol. 51, no. 4, pp. 375–381, 2003.
- T. Umemura, M. Hirakawa, Y. Yoshida, and K. Kurita, “Quantitative protection of chitin by one-step tritylation and benzylation to synthesize precursors for chemical modifications,” Polymer Bulletin, vol. 69, no. 3, pp. 303–312, 2012.
- O. Somorin, N. Nishi, S. Tokura, and J. Noguchi, “Studies on chitin-2. Preparation of benzyl and benzoylchitins,” Polymer Journal, vol. 11, no. 5, pp. 391–396, 1979.
- N. Teramoto, T. Motoyama, R. Yosomiya, and M. Shibata, “Synthesis and properties of thermoplastic propyl-etherified amylose,” European Polymer Journal, vol. 38, no. 7, pp. 1365–1369, 2002.
- M. Shibata, R. Nozawa, N. Teramoto, and R. Yosomiya, “Synthesis and properties of etherified pullulans,” European Polymer Journal, vol. 38, no. 3, pp. 497–501, 2002.
- K. Petzold, K. Schwikal, and T. Heinze, “Carboxymethyl xylan-synthesis and detailed structure characterization,” Carbohydrate Polymers, vol. 64, no. 2, pp. 292–298, 2006.
- L. J. Tanghe, L. B. Genung, and J. W. Mensch, “Cellulose acetate,” in Methods in Carbohydrate Chemistry, Vol III, Cellulose, R. L. Whistler, Ed., pp. 193–212, Academic Press, New York, NY, USA, 1963.
- C. L. McCormick and P. A. Callais, “Derivatization of cellulose in lithium chloride and N,N-dimethylacetamide solutions,” Polymer, vol. 28, no. 13, pp. 2317–2323, 1987.
- C. Grote and T. Heinze, “Starch derivatives of high degree of functionalization 11: studies on alternative acylation of starch with long-chain fatty acids homogeneously in N,N-dimethyl acetamide/LiCl,” Cellulose, vol. 12, no. 4, pp. 435–444, 2005.
- F. Belmokaddem, C. Pinel, P. Huber, M. Petit-Conil, and D. Da Silva Perez, “Green synthesis of xylan hemicellulose esters,” Carbohydrate Research, vol. 346, no. 18, pp. 2896–2904, 2011.
- M. Gröndahl, A. Teleman, and P. Gatenholm, “Effect of acetylation on the material properties of glucuronoxylan from aspen wood,” Carbohydrate Polymers, vol. 52, no. 4, pp. 359–366, 2003.
- R. C. Sun, J. M. Fang, J. Tomkinson, and C. A. S. Hill, “Esterification of hemicelluloses from poplar chips in homogenous solution of N, N-dimethylformamide/lithium chloride,” Journal of Wood Chemistry and Technology, vol. 19, no. 4, pp. 287–306, 1999.
- T. Heinze, T. F. Liebert, K. S. Pfeiffer, and M. A. Hussain, “Unconventional cellulose esters: synthesis, characterization and structure-property relations,” Cellulose, vol. 10, no. 3, pp. 283–296, 2003.
- J. Wu, J. Zhang, H. Zhang, J. He, Q. Ren, and M. Guo, “Homogeneous acetylation of cellulose in a new ionic liquid,” Biomacromolecules, vol. 5, no. 2, pp. 266–268, 2004.
- T. Heinze, K. Schwikal, and S. Barthel, “Ionic liquids as reaction medium in cellulose functionalization,” Macromolecular Bioscience, vol. 5, no. 6, pp. 520–525, 2005.
- J. E. Sealey, G. Samaranayake, J. G. Todd, and W. G. Glasser, “Novel cellulose derivatives. IV. Preparation and thermal analysis of waxy esters of cellulose,” Journal of Polymer Science B, vol. 34, no. 9, pp. 1613–1620, 1996.
- S. N. Pawar and K. J. Edgar, “Chemical modification of alginates in organic solvent systems,” Biomacromolecules, vol. 12, no. 11, pp. 4095–4103, 2011.
- M. E. I. Badawy, E. I. Rabea, T. M. Rogge et al., “Fungicidal and insecticidal activity of O-acyl chitosan derivatives,” Polymer Bulletin, vol. 54, no. 4-5, pp. 279–289, 2005.
- S. R. Labafzadeh, J. S. Kavakka, K. Sievänen, J. Asikkala, and I. Kilpeläinen, “Reactive dissolution of cellulose and pulp through acylation in pyridine,” Cellulose, vol. 19, no. 4, pp. 1295–1304, 2012.
- K. Arai, S. Sano, and H. Satoh, “Preparation of cellulose stilbene-4-carboxylate and its application to thin-layer chromatography,” Journal of Materials Chemistry, vol. 2, no. 12, pp. 1257–1260, 1992.
- K. Arai and S. Sano, “Preparation of cellulose 2-methylstilbene-5-carboxylate and photoregulation of its properties,” Journal of Materials Chemistry, vol. 4, no. 2, pp. 275–278, 1994.
- C. M. Buchanan, N. L. Buchanan, J. S. Debenham et al., “Preparation and characterization of arabinoxylan esters,” ACS Symposium Series, vol. 864, pp. 326–346, 2004.
- T. Iwata, A. Fukushima, K. Okamura, and J. Azuma, “DSC study on regioselectively substituted cellulose heteroesters,” Journal of Applied Polymer Science, vol. 65, no. 8, pp. 1511–1515, 1997.
- E. Pascu, “Halogenation,” in Methods in Carbohydrate Chemistry, Vol III, Cellulose, R. L. Whistler, Ed., p. 259, Academic Press, New York, NY, USA, 1963.
- K. Rahn, M. Diamantoglou, D. Klemm, H. Berghmans, and T. Heinze, “Homogeneous synthesis of cellulose p-toluenesulfonates in N,N-dimethylacetamide/LiCl solvent system,” Angewandte Makromolekulare Chemie, vol. 238, pp. 143–163, 1996.
- S. C. Fox, B. Li, D. Xu, and K. J. Edgar, “Regioselective esterification and etherification of cellulose: a review,” Biomacromolecules, vol. 12, no. 6, pp. 1956–1972, 2011.
- Y. Morita, Y. Sugahara, A. Takahashi, and M. Ibonai, “Preparation of chitin-p-toluenesulfonate and deoxy(thiocyanato) chitin,” European Polymer Journal, vol. 30, no. 11, pp. 1231–1236, 1994.
- A. F. Kolova, V. P. Komar, I. V. Skornyakov, A. D. Virnik, R. G. Zhbanov, and Z. A. Rogovin, Cellulose Chemistry and Technology, vol. 12, p. 553, 1978.
- G. Mocanu, M. Constantin, and A. Carpov, “Chemical reactions on polysaccharides, 5. Reaction of mesyl chloride with pullulan,” Die Angewandte Makromolekulare Chemie, vol. 241, no. 1, pp. 1–10, 1996.
- D. Klemm, T. Helme, B. Philipp, and W. Wagenbiecht, “New approaches to advanced polymers by selective cellulose functionalization,” Acta Polymerica, vol. 48, no. 8, pp. 277–297, 1997.
- A. Koschella, D. Fenn, N. Illy, and T. Heinze, “Regioselectively functionalized cellulose derivatives: a mini review,” Macromolecular Symposia, vol. 244, pp. 59–73, 2006.
- J. W. Green, “Triphenylmethyl ethers,” in Methods in Carbohydrate Chemistry, Vol III, Cellulose, R. L. Whistler, Ed., p. 327, Academic Press, New York, NY, USA, 1963.
- R. L. Whistler and S. Hirase, “Introduction of 3,6-anhydro rings into amylose and characterization of the products,” Journal of Organic Chemistry, vol. 26, no. 11, pp. 4600–4605, 1961.
- J. Holappa, T. Nevalainen, P. Soininen et al., “N-chloroacyl-6-O-triphenylmethylchitosans: useful intermediates for synthetic modifications of chitosan,” Biomacromolecules, vol. 6, no. 2, pp. 858–863, 2005.
- D. Klemm and A. J. Stein, “Silylated cellulose materials in design of supramolecular structures of ultrathin cellulose films,” Journal of Macromolecular Science A, vol. 32, no. 4, pp. 899–904, 1995.
- A. Koschella and D. Klemm, “Silylation of cellulose regiocontrolled by bulky reagents and dispersity in the reaction media,” Macromolecular Symposia, vol. 120, pp. 115–125, 1997.
- A. Koschella, T. Heinze, and D. Klemm, “First synthesis of 3-O-functionalized cellulose ethers via 2,6-di-O-protected silyl cellulose,” Macromolecular Bioscience, vol. 1, no. 1, pp. 49–54, 2001.
- D. Klemm, B. Heublein, H. Fink, and A. Bohn, “Cellulose: fascinating biopolymer and sustainable raw material,” Angewandte Chemie International Edition, vol. 44, no. 22, pp. 3358–3393, 2005.
- D. Xu, B. Li, C. Tate, and K. J. Edgar, “Studies on regioselective acylation of cellulose with bulky acid chlorides,” Cellulose, vol. 18, no. 2, pp. 405–419, 2011.
- J. Zhang, J. Wu, Y. Cao, S. Sang, J. Zhang, and J. He, “Synthesis of cellulose benzoates under homogeneous conditions in an ionic liquid,” Cellulose, vol. 16, no. 2, pp. 299–308, 2009.
- A. Stein and D. Klemm, “Syntheses of cellulose derivatives via O-triorganosilyl celluloses, 1. Effective synthesis of organic cellulose esters by acylation of trimethylsilyl celluloses,” Die Makromolekulare Chemie, Rapid Communications, vol. 9, no. 8, pp. 569–573, 1988.
- A. Koschella, T. Leermann, M. Brackhagen, and T. Heinze, “Study of sulfonic acid esters from 1→4-, 1→3-, and 1→6-linked polysaccharides,” Journal of Applied Polymer Science, vol. 100, no. 3, pp. 2142–2150, 2006.
- R. Dicke, K. Rahn, V. Haack, and T. Heinze, “Starch derivatives of high degree of functionalization. Part 2. Determination of the functionalization pattern of p-toluenesulfonyl starch by peracylation and NMR spectroscopy,” Carbohydrate Polymers, vol. 45, no. 1, pp. 43–51, 2001.
- D. M. Clode and D. Horton, “Preparation and characterization of the 6-aldehydo derivatives of amylose and whole starch,” Carbohydrate Research, vol. 17, no. 2, pp. 365–373, 1971.
- J. Ren, P. Wang, F. Dong, Y. Feng, D. Peng, and Z. Guo, “Synthesis and antifungal properties of 6-amino-6-deoxyinulin, a kind of precursors for facile chemical modifications of inulin,” Carbohydrate Polymers, vol. 87, no. 2, pp. 1744–1748, 2012.
- H. N. Cheng and Q. M. Gu, “Enzyme-catalyzed modifications of polysaccharides and poly(ethylene glycol),” Polymers, vol. 4, no. 2, pp. 1311–1330, 2012.
- F. F. Bruno, J. A. Akkara, M. Ayyagari et al., “Enzymatic modification of insoluble amylose in organic solvents,” Macromolecules, vol. 28, no. 26, pp. 8881–8883, 1995.
- J. Xie and Y. Hsieh, “Enzyme-catalyzed transesterification of vinyl esters on cellulose solids,” Journal of Polymer Science A, vol. 39, no. 11, pp. 1931–1939, 2001.
- S. Chakraborty, B. Sahoo, I. Teraoka, L. M. Miller, and R. A. Gross, “Enzyme-catalyzed regioselective modification of starch nanoparticles,” Macromolecules, vol. 38, no. 1, pp. 61–68, 2005.
- A. Alissandratos, N. Baudendistel, S. L. Flitsch, B. Hauer, and P. J. Halling, “Lipase-catalysed acylation of starch and determination of the degree of substitution by methanolysis and GC,” BMC Biotechnology, vol. 10, p. 82, 2010.
- K. Yang and Y. J. Wang, “Lipase-catalyzed cellulose acetylation in aqueous and organic media,” Biotechnology Progress, vol. 19, no. 6, pp. 1664–1671, 2003.
- K. Yang, Y. J. Wang, and M. I. Kuo, “Effects of substrate pretreatment and water activity on lipase-catalyzed cellulose acetylation in organic media,” Biotechnology Progress, vol. 20, no. 4, pp. 1053–1061, 2004.
- A. Rajan, V. S. Prasad, and T. E. Abraham, “Enzymatic esterification of starch using recovered coconut oil,” International Journal of Biological Macromolecules, vol. 39,, no. 4-5, pp. 265–272, 2006.
- A. Rajan and T. E. Abraham, “Enzymatic modification of cassava starch by bacterial lipase,” Bioprocess and Biosystems Engineering, vol. 29, no. 1, pp. 65–71, 2006.
- A. Rajan, J. D. Sudha, and T. E. Abraham, “Enzymatic modification of cassava starch by fungal lipase,” Industrial Crops and Products, vol. 27, no. 1, pp. 50–59, 2008.
- V. Sereti, H. Stamatis, E. Koukios, and F. N. Kolisis, “Enzymatic acylation of cellulose acetate in organic media,” Journal of Biotechnology, vol. 66, no. 2-3, pp. 219–223, 1998.
- C. Altaner, B. Saake, M. Tenkanen et al., “Regioselective deacetylation of cellulose acetates by acetyl xylan esterases of different CE-families,” Journal of Biotechnology, vol. 105, no. 1-2, pp. 95–104, 2003.
- R. S. Tipson, “Sulfonic esters of carbohydrates,” Advances in Carbohydrate Chemistry, vol. 8, pp. 180–215, 1953.
- J. W. H. Oldham and J. K. Rutherford, “The alkylation of amines as catalyzed by nickel,” Journal of the American Chemical Society, vol. 54, no. 1, pp. 306–312, 1932.
- S. S. Shaik, “The α- and β-carbon substituent effect on SN2 reactivity. A valence-bond approach,” Journal of the American Chemical Society, vol. 105, no. 13, pp. 4359–4367, 1983.
- K. Petzold-Welcke, N. Michaelis, and T. Heinze, “Unconventional cellulose products through nucleophilic displacement reactions,” Macromolecular Symposia, vol. 280, no. 1, pp. 72–85, 2009.
- P. R. Skaanderup, C. S. Poulsen, L. Hyldtoft, M. R. Jørgensen, and R. Madsen, “Regioselective conversion of primary alcohols into iodides in unprotected methyl furanosides and pyranosides,” Synthesis, no. 12, pp. 1721–1727, 2002.
- A. L. Cimecioglu, D. H. Ball, D. L. Kaplan, and S. H. Huang, “Preparation of 6-O-acyl amylose derivatives,” in Proceedings of the MRS Symposium, pp. 7–12, December 1993.
- D. H. Ball, B. J. Wiley, and E. T. Reese, “Effect of substitution at C-6 on the susceptibility of pullulan to pullulanases. Enzymatic degradation of modified pullulans,” Canadian Journal of Microbiology, vol. 38, no. 4, pp. 324–327, 1992.
- H. Tseng, K. Takechi, and K. Furuhata, “Chlorination of chitin with sulfuryl chloride under homogeneous conditions,” Carbohydrate Polymers, vol. 33, no. 1, pp. 13–18, 1997.
- M. Sakamoto, H. Tseng, and K. Furuhata, “Regioselective chlorination of chitin with N-chlorosuccinimide-triphenylphosphine under homogeneous conditions in lithium chloride-N,N-dimethylacetamide,” Carbohydrate Research, vol. 265, no. 2, pp. 271–280, 1994.
- K. Furuhata, N. Aoki, S. Suzuki, M. Sakamoto, Y. Saegusa, and S. Nakamura, “Bromination of cellulose with tribromoimidazole, triphenylphosphine and imidazole under homogeneous conditions in LiBr-dimethylacetamide,” Carbohydrate Polymers, vol. 26, no. 1, pp. 25–29, 1995.
- K.-I. Furuhata, K. Koganei, H.-S. Chang, N. Aoki, and M. Sakamoto, “Dissolution of cellulose in lithium bromide-organic solvent systems and homogeneous bromination of cellulose with N-bromosuccinimide-triphenylphosphine in lithium bromide-N,N-dimethylacetamide,” Carbohydrate Research, vol. 230, no. 1, pp. 165–177, 1992.
- Y. Matsui, J. Ishikawa, H. Kamitakahara, T. Takano, and F. Nakatsubo, “Facile synthesis of 6-amino-6-deoxycellulose,” Carbohydrate Research, vol. 340, no. 7, pp. 1403–1406, 2005.
- H. Tseng, K. Furuhata, and M. Sakamoto, “Bromination of regenerated chitin with N-bromosuccinimide and triphenylphospine under homogeneous conditions in lithium bromide-N,N-dimethylacetamide,” Carbohydrate Research, vol. 270, no. 2, pp. 149–161, 1995.
- T. Hasegawa, M. Umeda, M. Numata et al., “‘Click chemistry’ on polysaccharides: a convenient, general, and monitorable approach to develop (1→3)-β-d-glucans with various functional appendages,” Carbohydrate Research, vol. 341, no. 1, pp. 35–40, 2006.
- G. N. Smirnova, L. S. Gol’braikh, A. I. Polyakov, and Z. A. Rogovin, “Synthesis of 2, 3-anhydro-6-O-tritylcellulose,” Chemistry of Natural Compounds, vol. 2, no. 1, pp. 1–3, 1966.
- S. Immel, K. Fujita, H. J. Lindner, Y. Nogami, and F. W. Lichtenthaler, “Structure and lipophilicity profile of 2,3-anhydro-α-cyclomannin and its ethanol inclusion complex,” Chemistry A, vol. 6, no. 13, pp. 2327–2333, 2000.
- Z. A. Rogovin and T. V. Vladimirov, Chimičeskaja Nauka i Promyšlennost, vol. 2, p. 527, 1957.
- Z. A. Rogovin and T. V. Vladimirov, Chemical Abstracts, vol. 52, p. 4167, 1958.
- T. R. Ingle and R. L. Whistler, “3,6-anhydroamylose by nucleophilic displacement,” in Methods in Carbohydrate Chemistry, Vol 5, General Polysaccharides, R. L. Whistler, Ed., p. 411, Academic Press, New York, NY, USA, 1963.
- I. Cumpstey, J. Frigell, E. Pershagen et al., “Amine-linked diglycosides: synthesis facilitated by the enhanced reactivity of allylic electrophiles, and glycosidase inhibition assays,” Beilstein Journal of Organic Chemistry, vol. 7, pp. 1115–1123, 2011.
- T. Heinze, A. Koschella, M. Brackhagen, J. Engelhardt, and K. Nachtkamp, “Studies on non-natural deoxyammonium cellulose,” Macromolecular Symposia, vol. 244, pp. 74–82, 2006.
- C. Liu and H. Baumann, “Exclusive and complete introduction of amino groups and their N-sulfo and N-carboxymethyl groups into the 6-position of cellulose without the use of protecting groups,” Carbohydrate Research, vol. 337, no. 14, pp. 1297–1307, 2002.
- Y. Matsui, J. Ishikawa, H. Kamitakahara, T. Takano, and F. Nakatsubo, “Facile synthesis of 6-amino-6-deoxycellulose,” Carbohydrate Research, vol. 340, no. 7, pp. 1403–1406, 2005.
- T. Takano, J. Ishikawa, H. Kamitakahara, and F. Nakatsubo, “The application of microwave heating to the synthesis of 6-amino-6-deoxycellulose,” Carbohydrate Research, vol. 342, no. 16, pp. 2456–2460, 2007.
- C. Xiao, D. Lu, S. Xu, and L. Huang, “Tunable synthesis of starch-poly(vinyl acetate) bioconjugate,” Starch-Stärke, vol. 63, no. 4, pp. 209–216, 2011.
- G. Zampano, M. Bertoldo, and F. Ciardelli, “Defined chitosan-based networks by C-6-azide-alkyne “click” reaction,” Reactive and Functional Polymers, vol. 70, no. 5, pp. 272–281, 2010.
- A. L. Cimecioglu, D. H. Ball, S. H. Huang, and D. L. Kaplan, “A direct regioselective route to 6-azido-6-deoxy polysaccharides under mild and homogeneous conditions,” Macromolecules, vol. 30, no. 1, pp. 155–156, 1997.
- J. Shey, K. M. Holtman, R. Y. Wong et al., “The azidation of starch,” Carbohydrate Polymers, vol. 65, no. 4, pp. 529–534, 2006.
- S. Knaus, U. Mais, and W. H. Binder, “Synthesis, characterization and properties of methylaminocellulose,” Cellulose, vol. 10, no. 2, pp. 139–150, 2003.
- C. Liu and H. Baumann, “New 6-butylamino-6-deoxycellulose and 6-deoxy-6-pyridiniumcellulose derivatives with highest regioselectivity and completeness of reaction,” Carbohydrate Research, vol. 340, no. 14, pp. 2229–2235, 2005.
- G. R. Saad and K.-I. Furuhata, “Dielectric study of β-relaxation in some cellulosic substances,” Polymer International, vol. 41, no. 3, pp. 293–299, 1996.
- A. Koschella and T. Heinze, “Novel regioselectively 6-functionalized cationic cellulose polyelectrolytes prepared via cellulose sulfonates,” Macromolecular Bioscience, vol. 1, no. 5, pp. 178–184, 2001.
- N. Aoki, K. Koganei, H. Chang, K. Furuhata, and M. Sakamoto, “Gas chromatographic-mass spectrometric study of reactions of halodeoxycelluloses with thiols in aqueous solutions,” Carbohydrate Polymers, vol. 27, no. 1, pp. 13–21, 1995.
- N. Aoki, K. Furuhata, Y. Saegusa, S. Nakamura, and M. Sakamoto, “Reaction of 6-bromo-6-deoxycellulose with thiols in lithium bromide-N,N-dimethylacetamide,” Journal of Applied Polymer Science, vol. 61, no. 7, pp. 1173–1185, 1996.
- G. Wenz, P. Liepold, and N. Bordeanu, “Synthesis and SAM formation of water soluble functional carboxymethylcelluloses: thiosulfates and thioethers,” Cellulose, vol. 12, no. 1, pp. 85–96, 2005.
- N. Aoki, K. Fukushima, H. Kurakata, M. Sakamoto, and K. Furuhata, “6-Deoxy-6-mercaptocellulose and its S-substituted derivatives as sorbents for metal ions,” Reactive and Functional Polymers, vol. 42, no. 3, pp. 223–233, 1999.
- G. R. Saad and K. Furuhata, “Effect of substituents on dielectric β-relaxation in cellulose,” Polymer International, vol. 42, no. 4, pp. 356–362, 1997.
- D. Horton and D. H. Hutson, “Developments in the chemistry of thio sugars,” Advances in Carbohydrate Chemistry C, vol. 18, pp. 123–199, 1963.
- D. Trimnell, E. I. Stout, W. M. Doane, and C. R. Russel, “Preparation of starch 2-hydroxy-3-mercaptopropyl ethers and their use in graft polymerizations,” Journal of Applied Polymer Science, vol. 22, no. 12, pp. 3579–3586, 1978.
- E. Mentasti, C. Sarzanini, M. C. Gennaro, and V. Porta, “Nitrilotriacetic acid, thiourea and cysteine ligands immobilized on cellulose for the uptake of trace metal ions,” Polyhedron, vol. 6, no. 6, pp. 1197–1202, 1987.
- I. Cumpstey, “Neodisaccharide diglycosyl compounds: ethers, thioethers and selenoethers. A survey of their synthesis and biological activity,” Comptes Rendus Chimie, vol. 14, no. 2-3, pp. 274–285, 2011.
- V. Fournière and I. Cumpstey, “Synthesis of non-glycosidically linked selenoether pseudodisaccharides,” Tetrahedron Letters, vol. 51, no. 16, pp. 2127–2129, 2010.
- K. A. Kristiansen, A. Potthast, and B. E. Christensen, “Periodate oxidation of polysaccharides for modification of chemical and physical properties,” Carbohydrate Research, vol. 345, no. 10, pp. 1264–1271, 2010.
- S. Coseri, G. Biliuta, B. C. Simionescu, K. Stana-Kleinschek, V. Ribitsch, and V. Harabagiu, “Oxidized cellulose-Survey of the most recent achievements,” Carbohydrate Polymers, 2012.
- Van Bekkum, “Studies on selective carbohydrate oxidation,” in Carbohydrates as Organic Raw Materials, F. Lichtenthaler, Ed., p. 289, VCH, Weinheim, Germany, 1990.
- G. O. Aspinall and A. Nicolson, “Paper 505. The catalytic oxidation of European larch ε-galactan,” Journal of the Chemical Society, pp. 2503–2507, 1960.
- D. L. Verraest, J. A. Peters, and H. Van Bekkum, “The platinum-catalyzed oxidation of inulin,” Carbohydrate Research, vol. 306, no. 1-2, pp. 197–203, 1998.
- G. O. Aspinall, “Reduction of uronic acids in polysaccharides,” in Methods in Carbohydrate Chemistry, Vol 5, General Polysaccharides, R. L. Whistler, Ed., p. 397, Academic Press, New York, NY, USA, 1963.
- A. E. J. de Nooy, A. C. Besemer, and H. van Bekkum, “Highly selective tempo mediated oxidation of primary alcohol groups in polysaccharides,” Recueil des Travaux Chimiques des Pays-Bas, vol. 113, no. 3, pp. 165–166, 1994.
- A. E. J. De Nooy, A. C. Besemer, and H. Van Bekkum, “Highly selective nitroxyl radical-mediated oxidation of primary alcohol groups in water-soluble glucans,” Carbohydrate Research, vol. 269, no. 1, pp. 89–98, 1995.
- P. S. Chang and J. F. Robyt, “Oxidation of primary alcohol groups of naturally occurring polysaccharides with 2,2,6,6-tetramethyl-1-piperidine oxoammonium ion,” Journal of Carbohydrate Chemistry, vol. 15, no. 7, pp. 819–830, 1996.
- A. Isogai and Y. Kato, “Preparation of polyuronic acid from cellulose by TEMPO-mediated oxidation,” Cellulose, vol. 5, no. 3, pp. 153–164, 1998.
- R. A. A. Muzzarelli, C. Muzzarelli, A. Cosani, and M. Terbojevich, “6-Oxychitins, novel hyaluronan-like regiospecifically carboxylated chitins,” Carbohydrate Polymers, vol. 39, no. 4, pp. 361–367, 1999.
- P. L. Bragd, A. C. Besemer, and H. Van Bekkum, “Bromide-free TEMPO-mediated oxidation of primary alcohol groups in starch and methyl α-d-glucopyranoside,” Carbohydrate Research, vol. 328, no. 3, pp. 355–363, 2000.
- K. Maurer and G. Drefahl, “Oxydationen mit stickstoffdioxyd, I. Mitteil.: die Darstellung von glyoxylsäure, glucuronsäure und galakturonsäure,” Berichte der Deutschen Chemischen Gesellschaft, vol. 75, no. 12, pp. 1489–1491, 1942.
- E. C. Yackel and W. O. Kenyon, “The oxidation of cellulose by nitrogen dioxide,” Journal of the American Chemical Society, vol. 64, no. 1, pp. 121–127, 1942.
- K. Parikka and M. Tenkanen, “Oxidation of methyl α-d-galactopyranoside by galactose oxidase: products formed and optimization of reaction conditions for production of aldehyde,” Carbohydrate Research, vol. 344, no. 1, pp. 14–20, 2009.
- K. Parikka, A. -S. Leppänen, L. Piktänen, M. Reunanen, S. Willför, and M. Tenkanen, “Oxidation of polysaccharides by galactose oxidase,” Journal of Agricultural and Food Chemistry, vol. 58, no. 1, pp. 262–271, 2010.
- E. Frollini, W. F. Reed, M. Milas, and M. Rinaudo, “Polyelectrolytes from polysaccharides: selective oxidation of guar gum-a revisited reaction,” Carbohydrate Polymers, vol. 27, no. 2, pp. 129–135, 1995.
- M. Yalpani and L. D. Hall, “Some chemical and analytical aspects of polysaccharide modifications. 3. Formation of branched-chain, soluble chitosan derivatives,” Macromolecules, vol. 17, no. 3, pp. 272–281, 1984.
- S. Dumitriu, Polysaccharides: Structural Diversity and Functional Versatility, Marcel Dekker, New York, NY, USA, 2005.
- J. Yang, Y. Xie, and W. He, “Research progress on chemical modification of alginate: a review,” Carbohydrate Polymers, vol. 84, no. 1, pp. 33–39, 2011.
- M. D. Cathell, J. C. Szewczyk, and C. L. Schauer, “Organic modification of the polysaccharide alginate,” Mini-Reviews in Organic Chemistry, vol. 7, no. 1, pp. 61–67, 2010.
- S. Pelletier, P. Hubert, F. Lapicque, E. Payan, and E. Dellacherie, “Amphiphilic derivatives of sodium alginate and hyaluronate: synthesis and physico-chemical properties of aqueous dilute solutions,” Carbohydrate Polymers, vol. 43, no. 4, pp. 343–349, 2000.
- C. S. Pappas, A. Malovikova, Z. Hromadkova, P. A. Tarantilis, A. Ebringerova, and M. G. Polissiou, “Determination of the degree of esterification of pectinates with decyl and benzyl ester groups by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and curve-fitting deconvolution method,” Carbohydrate Polymers, vol. 56, no. 4, pp. 465–469, 2004.
- G. A. Morris, Z. Hromadkova, A. Ebringerova, A. Malovikova, J. Alföldi, and S. E. Harding, “Modification of pectin with UV-absorbing substitutents and its effect on the structural and hydrodynamic properties of the water-soluble derivatives,” Carbohydrate Polymers, vol. 48, no. 4, pp. 351–359, 2002.
- J. S. Yang, H. B. Ren, and Y. J. Xie, “Synthesis of amidic alginate derivatives and their application in microencapsulation of λ-cyhalothrin,” Biomacromolecules, vol. 12, no. 8, pp. 2982–2987, 2011.
- F. Vallée, C. Müller, A. Durand et al., “Synthesis and rheological properties of hydrogels based on amphiphilic alginate-amide derivatives,” Carbohydrate Research, vol. 344, no. 2, pp. 223–228, 2009.
- A. Synytsya, J. Copikova, M. Marounek et al., “Preparation of N-alkylamides of highly methylated (HM) citrus pectin,” Czech Journal of Food Sciences, vol. 21, pp. 162–166, 2003.
- A. Sinitsya, J. Copikova, V. Prutyanov, S. Skoblya, and V. Machovic, “Amidation of highly methoxylated citrus pectin with primary amines,” Carbohydrate Polymers, vol. 42, no. 4, pp. 359–368, 2000.
- A. Synytsya, J. Copikova, M. Marounek et al., “N-octadecylpectinamide, a hydrophobic sorbent based on modification of highly methoxylated citrus pectin,” Carbohydrate Polymers, vol. 56, no. 2, pp. 169–179, 2004.
- I. Ugi, “Recent progress in the chemistry of multicomponent reactions,” Pure and Applied Chemistry, vol. 73, no. 1, pp. 187–191, 2001.
- J. P. Zhu, “Recent developments in the isonitrile-based multicomponent synthesis of heterocycles,” European Journal of Organic Chemistry, no. 7, pp. 1133–1144, 2003.
- P. Slobbe, E. Ruijter, and R. V. A. Orru, “Recent applications of multicomponent reactions in medicinal chemistry,” Medicinal Chemistry Communications, vol. 3, pp. 1189–1218, 2012.
- R. V. A. Orru and E. Ruijter, Synthesis of Heterocycles via Multicomponent Reactions, Springer, Berlin, Germany, 2010.
- I. Ugi, R. Meyr, U. Fetzer, and C. Steinbrückner, “Versuche mit Isonitrilen,” Angewandte Chemie, vol. 71, no. 11, pp. 386–388, 1959.
- I. Ugi and C. Steinbrückner, “Über ein neues Kondensations-Prinzip,” Angewandte Chemie, vol. 72, no. 7-8, pp. 267–268, 1960.
- H. Bu, A. L. Kjøniksen, K. D. Knudsen, and B. Nyström, “Rheological and structural properties of aqueous alginate during gelation via the Ugi multicomponent condensation reaction,” Biomacromolecules, vol. 5, no. 4, pp. 1470–1479, 2004.
- J. Desbrieres, C. Martinez, and M. Rinaudo, “Hydrophobic derivatives of chitosan: characterization and rheological behaviour,” International Journal of Biological Macromolecules, vol. 19, no. 1, pp. 21–28, 1996.
- M. E. I. Badawy, “Chemical modification of chitosan: synthesis and biological activity of new heterocyclic chitosan derivatives,” Polymer International, vol. 57, no. 2, pp. 254–261, 2000.
- E. I. Rabea, M. E. I. Badawy, T. M. Rogge et al., “Enhancement of fungicidal and insecticidal activity by reductive alkylation of chitosan,” Pest Management Science, vol. 62, no. 9, pp. 890–897, 2006.
- K. Tømmeraas, S. P. Strand, W. Tian, L. Kenne, and K. M. Våruma, “Preparation and characterisation of fluorescent chitosans using 9-anthraldehyde as fluorophore,” Carbohydrate Research, vol. 336, no. 4, pp. 291–296, 2001.
- S. Hirano, K. Nagamura, M. Zhang et al., “Chitosan staple fibers and their chemical modification with some aldehydes,” Carbohydrate Polymers, vol. 38, no. 4, pp. 293–298, 1999.
- D. de Britto, R. C. Goy, S. P. C. Filho, and O. B. G. Assis, “Quaternary salts of chitosan: history, antimicrobial features, and prospects,” International Journal of Carbohydrate Chemistry, vol. 2011, Article ID 312539, 12 pages, 2011.
- V. Ö. Rúnarsson, J. Holappa, S. Jónsdóttir, H. Steinsson, and M. Másson, “N-selective “one pot” synthesis of highly N-substituted trimethyl chitosan (TMC),” Carbohydrate Polymers, vol. 74, no. 3, pp. 740–744, 2008.
- A. B. Sieval, M. Thanou, A. F. Kotzé, J. C. Verhoef, J. Brussee, and H. E. Junginger, “Preparation and NMR characterization of highly substituted N-trimethyl chitosan chloride,” Carbohydrate Polymers, vol. 36, no. 2-3, pp. 157–165, 1998.
- P. L. Dung, M. Milas, M. Rinaudo, and J. Desbrières, “Water soluble derivatives obtained by controlled chemical modifications of chitosan,” Carbohydrate Polymers, vol. 24, no. 3, pp. 209–214, 1994.
- Z. Jia, D. Shen, and W. Xu, “Synthesis and antibacterial activities of quaternary ammonium salt of chitosan,” Carbohydrate Research, vol. 333, no. 1, pp. 1–6, 2001.
- S. Hirano and Y. Yagi, “The effects of N-substitution of chitosan and the physical form of the products on the rate of hydrolysis by chitinase from Streptomyces griseus,” Carbohydrate Research, vol. 83, no. 1, pp. 103–108, 1980.
- S. Hirano, Y. Ohe, and H. Ono, “Selective N-acylation of chitosan,” Carbohydrate Research, vol. 47, no. 2, pp. 314–320, 1976.
- K. Y. Lee, W. S. Ha, and W. H. Park, “Blood compatibility and biodegradability of partially N-acylated chitosan derivatives,” Biomaterials, vol. 16, no. 16, pp. 1211–1216, 1995.
- C. Y. Choi, S. B. Kim, P. K. Pak, D. I. Yoo, and Y. S. Chung, “Effect of N-acylation on structure and properties of chitosan fibers,” Carbohydrate Polymers, vol. 68, no. 1, pp. 122–127, 2007.
- T. Ishii, “Facile preparation of deoxyiodocellulose and its conversion into 5,6-cellulosene,” Carbohydrate Research, vol. 154, no. 1, pp. 63–70, 1986.
- D. Horton and M. H. Meshreki, “Synthesis of 2.3-unsaturated polysaccharides from amylose and xylan,” Carbohydrate Research, vol. 40, no. 2, pp. 345–352, 1975.
- Z. Liu, B. Classon, and B. Samuelsson, “A novel route to olefins from vicinal diols,” Journal of Organic Chemistry, vol. 55, no. 14, pp. 4273–4275, 1990.
- B. Classon, P. J. Garegg, and B. Samuelsson, “A facile preparation of 2′,3′-unsaturated nucleosides and hexopyranosides from acetylated halohydrins by reductive elimination,” Acta Chemica Scandinavica B, vol. 36, p. 251, 1982.
- M. J. Robins, J. S. Wilson, D. Madej, N. H. Low, F. Hansske, and S. F. Wnuk, “Nucleic acid-related compounds. 88. Efficient conversions of ribonucleosides into their 2′,3′-anhydro, 2′(and 3′)-deoxy, 2′,3′-didehydro-2′,3′-dideoxy, and 2′,3′-dideoxynucleoside analogs,” Journal of Organic Chemistry, vol. 60, no. 24, pp. 7902–7908, 1995.
- L. Alvarez de Cienfuegos, A. J. Mota, C. Rodriguez, and R. Robles, “Highly efficient synthesis of 2′,3′-didehydro-2′,3′-dideoxy-β-nucleosides through a sulfur-mediated reductive 2′,3′-trans-elimination. From iodomethylcyclopropanes to thiirane analogs,” Tetrahedron Letters, vol. 46, no. 3, pp. 469–473, 2005.