About this Journal Submit a Manuscript Table of Contents
Advances in Materials Science and Engineering
Volume 2013 (2013), Article ID 382635, 10 pages
http://dx.doi.org/10.1155/2013/382635
Research Article

A Study on the Influence of the Forming Strategy on the Main Strains, Thickness Reduction, and Forces in a Single Point Incremental Forming Process

Lucian Blaga University of Sibiu, Faculty of Engineering, Victoriei Boulevard 10, 550024 Sibiu, Romania

Received 25 May 2013; Revised 17 August 2013; Accepted 18 August 2013

Academic Editor: Tao Zhang

Copyright © 2013 Adrian Blaga and Valentin Oleksik. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Pohlak, J. Majak, and R. Küttner, “Incremental sheet forming process modelling—plimitation analysis,” Journal of Achievements in Materials and Manufacturing Engineering, vol. 22, no. 2, pp. 67–70, 2007.
  2. M. B. Silva, M. Skjoedt, P. A. F. Martins, and N. Bay, “Revisiting the fundamentals of single point incremental forming by means of membrane analysis,” International Journal of Machine Tools and Manufacture, vol. 48, no. 1, pp. 73–83, 2008. View at Publisher · View at Google Scholar · View at Scopus
  3. Z. Liu, Y. Li, and P. A. Meehan, “Vertical wall formation and material flow control for incremental sheet forming by revisiting multistage deformation path strategies,” Materials and Manufacturing ProcessesIssue, vol. 25, no. 5, pp. 562–571, 2013.
  4. M. Yamashita, M. Gotoh, and S.-Y. Atsumi, “Numerical simulation of incremental forming of sheet metal,” Journal of Materials Processing Technology, vol. 199, no. 1, pp. 163–172, 2008. View at Publisher · View at Google Scholar · View at Scopus
  5. J. Li, P. Geng, and J. Shen, “Numerical simulation and experimental investigation of multistage incremental sheet forming,” The International Journal of Advanced Manufacturing Technology. In press.
  6. Z. Cui, L. Gao, F. Ren, V. Kiridena, and Z. C. Xia, “Deformation analysis of incremental sheet forming,” SAE International Journal of Materials and Manufacturing, vol. 3, no. 1, pp. 732–736, 2010. View at Publisher · View at Google Scholar · View at Scopus
  7. M. Bambach, B. Taleb Araghi, and G. Hirt, “Strategies to improve the geometric accuracy in asymmetric single point incremental forming,” Production Engineering, vol. 3, no. 2, pp. 145–156, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. M. B. Silva and P. A. F. Martins, “Two-point incremental forming with partial die: theory and experimentation,” Journal of Materials Engineering and Performance, vol. 22, no. 4, pp. 1018–1027, 2013.
  9. K. Jackson and J. Allwood, “The mechanics of incremental sheet forming,” Journal of Materials Processing Technology, vol. 209, no. 3, pp. 1158–1174, 2009. View at Publisher · View at Google Scholar · View at Scopus
  10. F. C. Minutolo, M. Durante, A. Formisano, and A. Langella, “Forces analysis in sheet incremental forming and comparison of experimental and simulation results,” in Intelligent Production Machines and Systems, D. T. Pham, E. E. Eldukhri, and A. J. Soroka, Eds., pp. 229–234, Elsevier Science, Oxford, UK, 2006.
  11. J. R. Duflou, B. Callebaut, J. Verbert, and H. De Baerdemaeker, “Improved SPIF performance through dynamic local heating,” International Journal of Machine Tools and Manufacture, vol. 48, no. 5, pp. 543–549, 2008. View at Publisher · View at Google Scholar · View at Scopus
  12. A. Fiorentino, E. Ceretti, A. Attanasio, L. Mazzoni, and C. Giardini, “Analysis of forces, accuracy and formability in positive die sheet incremental forming,” International Journal of Material Forming, vol. 2, no. 1, pp. 805–808, 2009. View at Publisher · View at Google Scholar · View at Scopus
  13. M. Durante, A. Formisano, A. Langella, and F. M. Capece Minutolo, “The influence of tool rotation on an incremental forming process,” Journal of Materials Processing Technology, vol. 209, no. 9, pp. 4621–4626, 2009. View at Publisher · View at Google Scholar · View at Scopus
  14. G. Ambrogio, L. Filice, and F. Micari, “A force measuring based strategy for failure prevention in incremental forming,” Journal of Materials Processing Technology, vol. 177, no. 1-3, pp. 413–416, 2006. View at Publisher · View at Google Scholar · View at Scopus
  15. G. Ambrogio, V. Cozza, L. Filice, and F. Micari, “An analytical model for improving precision in single point incremental forming,” Journal of Materials Processing Technology, vol. 191, no. 1–3, pp. 92–95, 2007. View at Publisher · View at Google Scholar · View at Scopus
  16. M. Bambach, B. Taleb Araghi, and G. Hirt, “Strategies to improve the geometric accuracy in asymmetric single point incremental forming,” Production Engineering, vol. 3, no. 2, pp. 145–156, 2009. View at Publisher · View at Google Scholar · View at Scopus
  17. G. Hussain and L. Gao, “A novel method to test the thinning limits of sheet metals in negative incremental forming,” International Journal of Machine Tools and Manufacture, vol. 47, no. 3-4, pp. 419–435, 2007. View at Publisher · View at Google Scholar · View at Scopus
  18. A. Attanasio, E. Ceretti, and C. Giardini, “Optimization of tool path in two points incremental forming,” Journal of Materials Processing Technology, vol. 177, no. 1–3, pp. 409–412, 2006. View at Publisher · View at Google Scholar · View at Scopus
  19. M. Rauch, J.-Y. Hascoet, J.-C. Hamann, and Y. Plenel, “Tool path programming optimization for incremental sheet forming applications,” CAD Computer Aided Design, vol. 41, no. 12, pp. 877–885, 2009. View at Publisher · View at Google Scholar · View at Scopus
  20. Z. Fu, J. Mo, F. Han, and P. Gong, “Tool path correction algorithm for single-point incremental forming of sheet metal,” The International Journal of Advanced Manufacturing Technology, vol. 64, no. 9–12, pp. 1239–1248, 2013. View at Publisher · View at Google Scholar