Abstract

Broadband bandpass filters based on open complementary split ring resonators (OCSRRs) coupled through admittance inverters, and implemented in microstrip technology, are reported. As compared to other broadband filters based on open split ring resonators (OSRRs), ground plane etching is not necessary in the proposed filters. The selectivity of the filters at the upper transition band is improved thanks to the presence of a controllable transmission zero. To demonstrate the potential of this approach, two illustrative prototype devices have been designed and fabricated.

1. Introduction

Metamaterials have been a subject of increasing interest in the last decade. Soon after the synthesis of the first left-handed metamaterial based on a combination of metallic posts and split ring resonators (SRRs) in 2000 [1], the first works devoted to extend the properties and concepts of metamaterials to the design of microwave circuits in planar technology came into the scene [25]. In particular, it was demonstrated in [5] that a coplanar waveguide (CPW) transmission line loaded with SRRs [6] and shunt metallic strips exhibits a bandpass functionality with backward (or left-handed) wave propagation in the first allowed band. The CPW-based structure reported in [5] was the planar analog of the bulk structure reported in [1] and was the seed for further design of microwave filters based on SRRs, on their complementary counterparts (the complementary split ring resonator—CSRR [7]), or on other metamaterial resonators [818].

The filters reported in [818] are based on closed resonators (SRRs or CSRRs) coupled to a host line. However, filters based on electrically small open resonators, like the open split ring resonator (OSRR) [19], or the open complementary split ring resonator (OCSRR), [20] have also been reported [2125]. As compared to SRRs/CSRRs, the open resonators (OSRRs/OCSRRs) are electrically smaller by a factor of two [19, 20, 26]. Moreover, OSRRs and OCSRR are intrinsically wideband resonators (the reason for that is that, as compared to SRRs or CSRRs, OSRRs and OCSRRs exhibit high C/L and L/C ratios, resp., due to their topology, and this favors broadband responses); therefore, these open resonators are of interest for the implementation of moderate and wideband bandpass filters. It is remarkable that order-3 [27], order-5 [28], and order-7 [29] Chebyshev bandpass filters based on a combination of OSRRs and OCSRRs have been designed and fabricated. In such filters, the OSRRs and the OCSRRs are described by means of series and parallel resonators, respectively. Despite the fact that some parasitics must be introduced in the model in order to adequately describe the resonators loading a host line, the effects of these parasitics are not meaningful, and the filters exhibit the intended Chebyshev responses to a very good approximation.

In this paper, OCSRRs are used for the implementation of broadband bandpass filters in microstrip technology. The filters are similar to those filters reported in [20], that is, shunt connected OCSRRs coupled through admittance inverters. However, the filters in [20] are implemented in CPW technology, whereas the filters proposed in this paper are implemented in microstrip technology. As compared to the filters based on OSRRs and also implemented in microstrip technology, the advantage of our approach is that ground plane etching is not necessary. Moreover, the new proposed filters exhibit a transmission zero above the passband of interest that can be used to improve the filter selectivity above the pass band.

The paper is organized as follows. In Section 2, we will review the OCSRR for completeness, since this resonator is the key building block of the proposed filters. The design of the proposed broadband filters, including the simulation and measurement of the filter responses, are reported in Section 3. Finally, the main conclusions are highlighted in Section 4.

2. Open Complementary Split Ring Resonators (OCSRRs)

The OCSRR is the open version of the CSRR. The typical topology and circuit model of the OCSRR is depicted in Figure 1. For the OCSRR, the particle terminals (or ports) are indicated in the figure. Between these ports, there is an electric short through the metal between the inner and outer slot rings forming the particle, but there is also capacitive connection through the capacitances across the slots. Thus, according to this, the circuit model of the particle is an open parallel resonant tank, as Figure 1(b) illustrates. The inductance of the particle, , is the inductance of the metallic strip between the ring slots, and the capacitance, , is identical to the capacitance of the CSRR, that is, the capacitance of a disk of radius (where is the averaged radius) surrounded by a metallic plane at a distance of its edge [30] (notice that this means that the capacitance is identical to that of a slot ring with slot width and average radius , as it is justified in [30]). Since the inductance of the CSRR is /4 [30], it is expected that the resonance frequency of the OCSRR is one half the resonance frequency of the CSRR. The detailed calculation of is reported in [30], whereas is the inductance of the circular CPW structure that results from the OCSRR topology.

The previous model can be improved by considering the inductive effect of the metallic strip connecting the inner region of the particle and the metallic region in contact to port 2. This introduces an inductance in series with the parallel resonator, as reported in [29], and the effect of this inductance/strip is the presence of a short between ports 1 and 2 at a finite frequency (i.e., above the resonance frequency of the OCSRRs). In the bandpass filters based on OSRRs and OCSRRs reported by the authors, where the OCSRR is shunt connected to the host line, this short produces a transmission zero above the filter pass band. This improves the filter selectivity at the upper band and this strategy will be considered in the filters reported in this paper. However, in a first order approximation, the circuit of Figure 1(b) can be used for design purposes.

Let us now consider that the OCSRR is shunt connected to a microstrip transmission line. To effectively connect the resonator to ground, vias are required, as depicted in Figure 2(a). The structure is properly described by means of a shunt connected parallel resonant tank, as revealed by the reflection coefficient, represented in a Smith Chart in Figure 2(b) (notice that the reflection coefficient is always on the unit conductance circle, as expected from a reactive load in parallel to the 50 Ω impedance of the port). Figure 2(c) indicates that the resonance frequency of the OCSRR is roughly 1.5 GHz, where total transmission (reflection zero) appears since the shunt branch is opened at this frequency. Notice that for this particular OCSRR topology, the strip connecting the inner region of the OCSRR and the host line is wide, and the inductive effect can be neglected, at least in the frequency region shown in the figure (the structure is adequately modeled by means of a parallel resonant tank in such region).

3. Bandpass Filters Based on OCSRRs and Results

The proposed bandpass filters are implemented by means of shunt resonators coupled through admittance inverters (see Figure 3), following the theory reported in [31]. The first prototype device filter is an order-3 Chebyshev band pass filter with central frequency  GHz, ripple of 0.01 dB, and fractional bandwidth of 30%. For these specifications, considering identical resonators with a value of inductance and capacitance of nH and  pF, respectively, the characteristic admittance of the inverters are found to be  S, and  S. The considered and values are those extracted from the layout of the isolated resonator, which gives the required central frequency. The inverters are implemented by means of lines ( being the wavelength at the filter central frequency). The filter topology is depicted in Figure 4, where the main relevant dimensions are indicated (the filter has been fabricated following a standard photo/mask etching technique). The filter response, including the circuit simulation, the electromagnetic simulation (inferred by means of the Agilent Momentum commercial software), and the measured response (obtained by means of the Agilent PNA N5221A vector network analyzer) are depicted in Figure 5. The agreement between the electromagnetic simulation and measurement is remarkable. Notice that the measured filter selectivity at the upper edge of the band is much better than that obtained by the circuit simulation. The reason is the presence of the transmission zero above the passband, tailored by means of the width of the connecting strip between the inner region of the OCSRRs and the host line. Since the considered ripple is so small, the filter exhibits a quasi-Butterworth response, with a single reflection zero in the pass band. Filter performance is good, with a measured insertion loss smaller than 1.7 dB and return loss better than −10 dB between 1.68 GHz and 2.21 GHz. The filter upper stop band reveals that rejection is better than −10 dB up to at least 5 GHz.

Notice that the filter (measured) bandwidth is smaller than the bandwidth of the ideal response since the inverters strictly exhibit their functionality at the central filter frequency. This aspect is well known and can be solved by considering a larger nominal bandwidth. However, this is not relevant for our purposes, since the main aim is to demonstrate the potential of OCSRRs for the design of broadband microstrip filters based on admittance inverters, as an alternative to OSRR-based microstrip filters.

The second example is an order-3 Chebyshev band pass filter with central frequency  GHz, ripple of 0.1 dB, and fractional bandwidth of 30%. For these specifications,  nH and  pF, and the characteristic impedance of the inverters is  S, and  S. The topology and photograph of this filter are shown in Figure 6 and the frequency response in Figure 7. In this case, the pass band exhibits three reflection zeros and the return loss is better than −20 dB between 1.77 GHz and 2.25 GHz. Insertion loss is smaller than 0.9 dB within this frequency interval.

4. Conclusions

In conclusion, novel broadband microstrip bandpass filters based on OCSRRs coupled through admittance inverters have been proposed. The reported filters represent a significant progress as compared to other microstrip filters based on OSRRs, where ground plane etching in the region occupied by the OSRRs is necessary. The two designed filters exhibit good performance, and filter selectivity has been improved by the transmission zero inherent to the OCSRRs.

Acknowledgments

This work has been supported by MICIIN-Spain (Contracts TEC2010-17512 and CSD2008-00066) and by Generalitat de Catalunya (Project 2009SGR-421).