Abstract

An antipodal Vivaldi antenna operates simultaneously for telemetry and sensing when placed conformally onto PVC pipes. Good radiation efficiency is realised and the antenna impedance matching remains stable when a pipe is empty or contains water. The fidelity factor performance based on an input Ultra-Wideband Gaussian pulse is a suitable figure of merit to detect water presence. Different water levels and pipe conditions correspond to fidelity factors between 90% and 96%, which are a suitable dynamic range for sensing and the appropriate quality for pulse communications for remote monitoring.

1. Introduction

Monitoring pipe systems represents a major problem where continuous information on the liquid content must be constantly provided. This is the case for water leakage sensor networks or for stormwater detection in critical drainage system. Several technologies were proposed in the literature for these applications such as tracer gases and thermography [1]. Furthermore, ultrasound sensors have been proposed for accurate detection and localisation of leakages in buried water pipes [2, 3]. Acoustic wave monitoring is widely used in leak detection but they are concerns in terms of time response, robustness, reliability, accuracy, and costs. Radio-frequency telemetry has been more recently introduced to localize leaks and malfunctioning pipelines. In particular, Ground Penetrating Radar (GPR) systems can be efficiently designed to image subsurface scattering leaks by using low-frequency electromagnetic (EM) waves [4, 5]. However, due to their cost and characteristics, GPR is suitable for extraordinary maintenance. EM sensors revealing wave propagation distortion inside metallic pipes have been recently proposed [6]. Although reflections coming from leaks/cracks can be promptly identified by EM propagating mode monitoring, this technique is restricted to a limited number of applications and scenarios.

High data rates and low-power requirements make Ultra-Wideband (UWB) technology largely used for short-range wireless communication and sensor systems. With a large operating spectrum, short pulses can be generated. UWB sensors can then monitor pulse distortion and identify the associated environmental changes. Operating in the time domain implies the design of novel figures of merit to characterize UWB impulse radio systems. The signal purity in particular can be used to assess the time domain performance of the UWB front-end for antenna and sensor operative scenarios. This can be measured in terms of fidelity factor, which estimates the distortion of the received signal with respect to the original transmitted signal. This paper introduces a conformal antipodal Vivaldi antenna operating in the UWB range to be placed on Polyvinyl Chloride (PVC) pipes. This UWB directional antenna has been designed to fit onto a curved surface of a circular cross-section pipe for communication between flow rate meter devices [7]. The use of wireless monitoring technology to aid fluid flow control can improve reliability, reduce costs, and save space. This was proposed in [8] where an acoustic sensor is combined with to a radiotransmitter which communicates with an external gateway.

In this paper, an innovative UWB antenna for both sensing and data transmission is proposed for pipe telemetry applications. A preliminary study of the pipe proximity effects on a directional UWB antenna in the frequency domain [9] is extended by a thorough time domain analysis. Four standard PVC pipes have been numerically evaluated for different water content levels using the finite integration time domain technique (CST Microwave Studio [10]). Numerical results show that the conformal antipodal Vivaldi antenna is suitable for sensing the water level inside the pipe and for simultaneous transmission to an external metering station. These combined operations lead to significant simplification and cost saving for the metering system. In particular, the fidelity factor is shown to be a convenient metric to sense changes in water presence and to assess radiation properties. The time domain performance of the system is assessed by calculating the fidelity of the received pulse at a number of probes circularly distributed around the antenna in the -plane with a 5° step. The quality of a received pulse through the antenna system and the RF channel can be evaluated by using the following expression [11]: where the source pulse   and output pulse are normalised by their energy, respectively. The fidelity factor FF is the maximum integration by varying time delay . The linear operator describes the system transformation occurring in the input signal . In this case, as the transmit antenna is a Vivaldi type, a differentiation of the source pulse occurs [12] and the operator corresponds to .

The operating scenario is envisioned as follows. The pipe mounted antenna/sensor communicates to a UWB IEEE 802.15.4 node which can also be integrated in a Wi-Fi access point (AP). The UWB range is dependent on the data bandwidth, which in this case can be quite small, allowing a range of tens of meters. The position of antennas on the pipe should be considered in relation to the AP location.

2. Antipodal Vivaldi Antenna and Testing Environment

An antipodal Vivaldi antenna was designed to operate across the FCC UWB spectrum (3.1–10.6 GHz) when mounted on a pipe surface. The antenna is double-side printed on 0.375 mm thin Duroid 5870 dielectric substrate (, ) with overall dimensions 50 × 53 mm. This dielectric material was chosen for its stable electrical properties combined with mechanical flexibility that permits the antenna to be curved on a surface of a cylindrical object. Figure 1(a) shows the antenna geometry and the coordinate system. The tapered antenna aperture generates multiple resonances resulting in a continuous operating UWB bandwidth and a uniform end-fire directed radiation pattern. Figures 1(b) and 1(c) show the antenna curvature when the longitudinal axis of the pipe is rotated orthogonally to the antenna end-fire direction on 141.2 mm and 114.3 mm diameters of curvature, respectively.

In particular, the tapered line of the flare shape is described by two exponential curves given by (2) and then mirrored on the opposite side of the dielectric: for the internal and external tapered profile of each flare, respectively.

In order to reduce the back lobe radiation, the exponential lines were connected with spline shapes [13]. Finally, a tapered microstrip feeding line was designed to secure a broadband 50 Ω impedance condition in the intersection point [14].

2.1. Free-Space Antenna Characteristics

The performance of this antipodal Vivaldi antenna shows it to be resilient to mechanical bending along the -axis. Figure 2 shows the free-space  of the antenna in its flat and both curved configurations. The impedance matching expressed in terms of  remains stable across all configurations and below −10 dB over the complete UWB bandwidth.

Three-dimensional broadband free-space radiation patterns of the antenna in its flat and both curved configurations are shown in Figure 3. The patterns exhibit the same shape and high gain in the end-fire direction. Due to the antipodal configuration the beam in the direction is not totally symmetrical. Bending the antenna affects the radiation pattern in its cut as this corresponds to a rotation of the tapered line termination. As expected, by decreasing the diameter of curvature, the direction of maximum radiation moves from the direction towards the angular range 20°–30°. Moreover, significant radiation pattern stability can be observed across the entire FCC UWB band.

2.2. Pipe Characterization

Four different ASTM standard PVC pipes (; loss tangent = 0.086 at  GHz and 0.0182 at  GHz [15]) were considered and are summarized in Table 1 [16]. These dimensions are suitable for water and sanitary applications as well as stormwater drainage. The level to be detected has been characterised as “Empty” and “Full” for the pipe without and with water, respectively. The first-order Debye model with , , relaxation time ps, and has been used to model the dispersive behaviour of water.

2.3. Excitation Signal and Fidelity Factor Measurement

Choosing the excitation signal for the antenna is a very critical aspect of this analysis as the device is designed to operate as both sensor and transmitter. Several design factors need to be considered to select a suitable signal to feed the sensor/antenna:(i)antenna dimensions are inversely proportional to the lower edge frequency;(ii)considering that the antenna is placed close to water, the lower edge frequency must be selected in such a way this remains efficient in the lower part of the operating bandwidth;(iii) the system sensitivity to water loading is dependent on the bandwidth over which the fidelity factor is measured. In Figure 4 the normalised input signal selected for this application is plotted in the time domain. A convenient compromise between antenna efficiency and suitable fidelity factor sensitivity to the testing environment can be reached by using a Gaussian pulse centred at 7.5 GHz. Its frequency spectrum 20 dB bandwidth spans between 6.2 and 8.8 GHz.

3. Frequency Domain Performance

In this section the antenna performance is evaluated in the frequency domain when it is mounted conformally on the pipe configurations given in Table 1. Different diameters of curvature and thickness of the PVC pipes affect the antenna behaviour both in terms of impedance matching and radiation properties. But the presence of water inside the pipe generates the most evident variations. Figure 5 shows the resilience of the antenna impedance matching properties for the different pipe configurations when empty or full of water. It can be observed that the return loss curve drops to lower values when the pipe is filled with water as this introduces more losses. This effect is more evident for configurations A and C due to the thinner PVC layer between the antenna and the water content.

As from simulations the antenna shows stable radiation properties in terms of pattern shape over the operating bandwidth (6.2–8.8 GHz), the -plane diagrams are only displayed at the centre frequency 7.5 GHz (Figure 6). A significant gain drop occurs when the pipe is filled with water due to increased losses and dielectric loading. However, for all configurations investigated the antenna radiation remains efficient with and without water inside the pipe. Also the direction of maximum radiation changes because of the reflecting behaviour of the water content. In fact, this shifts towards the angular sector 30°–50° when the pipe is full of water.

4. Time Domain Performance

As the antenna is required to provide simultaneous transmission and sensor function, an angular sector where good radiation efficiency and sensing characteristics needs to be identified. As shown in Figure 6, for all the configurations investigated, a satisfactory compromise between the gain performance measured in the -plane with and without water is achieved in the range . Moreover, in this spatial region the fidelity factor assumes values above 90% that corresponds to a reliable radio link for pulse communications in all the analysed scenarios. Outside the interval 60°–70° a combined suitable performance in terms of gain (above 0 dBi) and FF (above 80%) was not found for all the scenarios under investigation. On the other hand, the fidelity factor can be also used as a valid figure of merit for sensing purposes. By definition, it depends on the variations of the transmitted signal across the entire bandwidth. As the antenna transmitting properties change when water fills the pipe, this effect is promptly expressed as a fidelity factor distortion. Figure 7 shows fidelity factor variations in the order of 6% between the cases “Empty” and “Full.” Once the system is properly characterised, those deviations can be used to monitor the water content inside the PVC pipes and simultaneously transmit the information to an external metering station.

5. Conclusions

A UWB directional antipodal Vivaldi antenna has been designed for water pipe sensing and telemetry. While the antenna impedance remains matched when placed on the four pipes investigated, gain and fidelity factor undergo a notable reduction with the pipe filled of water. The dispersive property of the pipe material and the water will modify the transfer function of the antenna, distorting the radiated and received signal shape. However, by focusing on the bandwidth between 6.2 and 8.8 GHz and the angular range in the -plane, the antenna radiates efficiently in all the scenarios investigated in terms of gain and fidelity factor figures. These properties suggested using the same antenna for simultaneous sensing and telemetry applications. As the water content causes fidelity factor variations between 90 and 96%, this figure is proposed as a reliable sensing parameter to assess the pipe content status. At the same time, as values above 80% secure good radiolinks for impulse communications, the antenna is able to transmit real-time information to an external telemetry station.