About this Journal Submit a Manuscript Table of Contents
ISRN Biotechnology

Volume 2014 (2014), Article ID 463074, 31 pages

http://dx.doi.org/10.1155/2014/463074
Review Article

Current Challenges in Commercially Producing Biofuels from Lignocellulosic Biomass

1DOE Great Lakes Bioenergy Research Center, Michigan State University, East Lansing, MI 48824, USA

2Biomass Conversion Research Laboratory (BCRL), Department of Chemical Engineering and Materials Science, Michigan State University, MBI Building, 3900 Collins Road, Lansing, MI 48910, USA

Received 15 December 2013; Accepted 19 February 2014; Published 5 May 2014

Academic Editors: G. Garrote, C. Han, S. Sanyal, and A. Trincone

Copyright © 2014 Venkatesh Balan. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

Biofuels that are produced from biobased materials are a good alternative to petroleum based fuels. They offer several benefits to society and the environment. Producing second generation biofuels is even more challenging than producing first generation biofuels due the complexity of the biomass and issues related to producing, harvesting, and transporting less dense biomass to centralized biorefineries. In addition to this logistic challenge, other challenges with respect to processing steps in converting biomass to liquid transportation fuel like pretreatment, hydrolysis, microbial fermentation, and fuel separation still exist and are discussed in this review. The possible coproducts that could be produced in the biorefinery and their importance to reduce the processing cost of biofuel are discussed. About $1 billion was spent in the year 2012 by the government agencies in US to meet the mandate to replace 30% existing liquid transportation fuels by 2022 which is 36 billion gallons/year. Other countries in the world have set their own targets to replace petroleum fuel by biofuels. Because of the challenges listed in this review and lack of government policies to create the demand for biofuels, it may take more time for the lignocellulosic biofuels to hit the market place than previously projected.

1. Introduction to Biorefineries

Biorefineries are manufacturing facilities that convert biobased materials (such as agricultural residues) to various products such as food, feed, fuels, chemicals, and energy [1, 2]. Biomass processing is analogous to petroleum refineries, which refine crude oil into several products including fuels (e.g., petrol, diesel, and kerosene) and chemical precursors like butanol for manufacturing different materials [3]. According to renewable energy policy network [4], in 2011, roughly 78% of energy consumed in the world was from fossil fuel, 3% from nuclear energy, and the remaining 19% from renewable energy that is obtained by renewable resources (wind, solar, geothermal, hydrothermal, and biomass). About 13% of the renewable energy is harnessed from carbon rich biobased materials available on earth either by directly burning biomass or by the thermochemical conversion of biomass to heat and power. Currently, the majority of biofuels are produced using sugars extracted from agricultural feedstock or by converting starch into sugars primarily from edible grains (Figure 1). The sugars from both the sources are then fermented into ethanol using yeast [5].

463074.fig.001
Figure 1: Contribution of renewable energy and biofuels in the total energy consumed in the world in 2011 [4]. Here, (a) gives details about world energy consumption; (b) gives details about world renewable energy consumption, and (c) gives details about different feedstock currently used for ethanol production.

Currently about 85 million barrels of crude oil are processed and used to meet the energy needs of the world. The demands for crude oil are projected to increase to 116 million barrels by 2030 [6]. Since this may result in depletion of crude oil reserves in the world, it is imperative to consider energy sources alternative to crude oil [7]. Biofuels and biochemicals produced using nonedible feedstock such as lignocellulosic biomass provide several benefits to the society [8] like (i) being renewable and sustainable, (ii) indirectly helping carbon dioxide (a greenhouse gas (GHG) that is responsible for global warming) fixation in the atmosphere, (iii) facilitating local economy development and stimulation, (iv) reducing air pollution from burning of biomass in fields and biomass rotting in fields, (v) bringing energy security for countries dependent on imported oil, and (vi) creating high technology jobs for engineers, fermentation specialists, process engineers, and scientists. In the fifties when petroleum processing was invented, the cost of feedstock was cheaper, but the processing costs were higher. Due to technology maturation and advancement, the processing costs have come down; however, depletion of crude oil supply is causing its cost to increase. Currently, it is estimated that conversion of lignocellulosic biomass to biofuels is costlier than its crude oil counterparts. However, it is anticipated that as the technology matures the cost will come down.

Raising fuel prices hamper the growth of the society as most humans depend on liquid fuels for transportation. Currently, fossil fuels are the only reliable source of energy to run ships, aircraft, trucks, and automobiles, which are essential modes of transportation for the smooth functioning of the society. The US Department of Energy (DOE) and the US Department of Agriculture (USDA) have mandated that 5% of heat and power energy, 20% of liquid transportation fuel, and 25% of chemicals and materials should come from biomass by 2022 [9]. About 36 billion gallons of liquid transportation fuels are needed to meet this ambitious goal. About 15 billion gallons of this biofuel will come from starch based ethanol, while the remaining 21 billion gallons (mostly ethanol) will be produced using cellulosic biomass (Figure 2) [9]. Similar goals were also set by the European Union (EU). Minor amounts of advanced biofuels are projected to come from noncellulosic biofuels by the conversion of gases like carbon monoxide from cement and steel industry using microbial transformation and from transesterification of used cooking oil or animal fat [10]. Other biofuels that are biochemically produced using sugars that could hit the market place are butanol, biofene, and bisabolene [11]. In order to meet these ambitious goals, biorefineries will be successful only if they can fully utilize biomass feedstock’s and transform all the components into valuable products [12, 13]. To be highly profitable, biorefineries will need to manage their own energy needs, produce low volume but high value products such as human food, chemical precursors, or medicinal compounds, and produce high volume low value products such as fuels and animal feed.

463074.fig.002
Figure 2: Projected biofuels (gallons/year) production capacity in US. Figure source: Congressional Research Service report number R40155. “Renewable Fuel Standard (RFS) overview and issues” January 23, 2012. The starch based ethanol will saturate at 15 billion gallons/year after 2011 and the amount of cellulosic biofuels production in the US will rise as high as 16 billion gallon/year.
1.1. First Generation Biorefineries

The first generation biorefineries used corn, wheat, cassava, barley, rye, soybean, sugarcane, sugar beet, or sweet sorghum as feedstocks (Figure 3). In the cases of sugarcane, sugar beet and sweet sorghum, the sugars are produced by squeezing the stem or by extraction using water [14]. These sugars are subsequently processed using either biological or catalytic transformation to chemicals [lactic acid, propionic acid, poly (3-hydroxyalkanoate acid)/poly (3-hydroxybutyric acid) (PHA/PHB), 1, 3-propane diol (PDO), poly-γ-glutamate] or fuels (ethanol, butanol) [15]. On the other hand, processing wheat, rye, corn, or soybean requires additional processing steps (jet cooking using steam followed by starch hydrolysis using enzymes like amylase), after which fuels and chemicals (mentioned above) are produced. Of these, ethanol is the leading biofuel produced around the world and is growing at a steady rate of 20% annually in the US alone [16]. Besides the leading ethanol producers (US followed by Brazil), other countries like France, China, and Canada have shown increasing ethanol productivity using feedstocks such as wheat, cassava, and sorghum juice. In addition to ethanol, several coproducts are produced including food (protein rich fraction, oil, corn steep liquor, and high fructose corn syrup), or animal feed (processed cake, dry distillers grains and solubles (DDGS), and gluten meal) based on the type of processing used (wet or dry milling) [17, 18]. Some other biobased products produced in the first generation biorefinery include adhesives, detergents, dyes, paper, cardboard, polymers, sorbents, paint pigments, and cleaning compounds [19, 20].

463074.fig.003
Figure 3: Different feedstocks used in the first and second generation biorefinery for producing biofuels, biochemicals, food, and feed.
1.2. Second Generation Biorefineries

Producing fuels from food grade materials has become a controversial topic as there are several million people in the world without sufficient food. Hence, researchers are now focused on developing second generation technologies to produce fuels and chemicals from nonedible feedstocks such as agricultural residue, forest residue, municipal solid waste, industrial waste, and dedicated energy crops [21]. There are two possible routes for converting biomass to biofuels. The first route is “thermochemical” and commonly referred to as biomass-to-liquid (BTL) conversion process. In BTL, the biomass is subjected to pyrolysis or gasification to produce syngas or synthesis gas (mixture of carbon monoxide and hydrogen). These gases are reformed to fuels using either a catalytic process such as the Fischer-Tropsch reactions or by a biological conversion. The second route is a “biochemical” route that transforms sugar polymers present in biomass (cellulose and hemicellulose) to monomeric sugars, which are fermented using microorganisms to produce fuels and chemicals [22] (Figure 3). The third alternative route is a “hybrid” route where a chemical intermediate is produced by a biochemical process and then transformed into higher value products using a thermochemical route. With investments from government agencies, research and development (R&D) has intensified the invention of novel technologies that has accelerated the production of second generation biofuels. Some of the noticeable investments were made by the US and European Union (EU) by establishing several bioenergy centers dedicated to performing basic science for the production of cost-effective biofuels that will lead to novel technologies. In combination, several big companies and startup companies in the US and Europe are developing pilot scale demonstration plants with funding from governments and venture capitalists to scale up these technologies [23].

Recent estimates of biofuel production costs show that second generation biofuels are two to three times more expensive than petroleum fuels on an energy equivalent basis [24]. To bring down the production cost, several challenges in converting lignocellulosic biomass to biofuels and chemicals using biochemical platforms [2527] need to be addressed. These challenges are in the areas of (i) feedstock production, (ii) feedstock logistics, (iii) development of energy efficient technologies (pretreatment, enzyme hydrolysis, and microbial fermentation), (iv) coproducts development, (v) establishment of biofuel and biochemical standards, (vi) biofuel distribution, (vii) societal acceptance, and (viii) environmental impact minimization. All of these challenging areas require expertise in agronomy, biomass logistics, biomass conversion, process engineering, chemistry, conversion technology, genetic engineering, microbial fermentation, economics, and environmental science. Details surrounding the challenges associated with bringing biofuels and biochemicals to market are discussed in this review.

2. Bioenergy Feedstock

Bioenergy plants are broadly classified into two categories, (i) gymnosperms (soft woods like pine, spruce, fir, and cedar) and (ii) angiosperms [monocots: all perennial grasses (e.g., switchgrass, Miscanthus, Sorghum, sugarcane, and bamboo) and herbaceous species (e.g., corn, wheat, and rice); dicots: flowering plants (alfalfa, soybean tobacco), hardwoods (e.g., poplar, willow, and black locust)] [28, 29]. The cell wall components (cellulose, hemicellulose, lignin, and ash) vary for different species of plants [30, 31]. Most of the dicots and some monocots have cellulose microfibrils cross-linked with xyloglucans with little arabinoxylan linkages. On the other hand, most monocots consist of glucuronoarabinoxylans as the major cross-linked glycans that are hydrogen bonded to cellulose microfibrils. The lignin [aromatic polymer comprising of syringyl (S), guaiacyl (G), and p-hydroxyphenyl (H)] content and its composition significantly vary in different plant species. Gymnosperms have the highest lignin content and comprises of G and H units. Hard wood species mainly have G and S units and minor amounts of H-units. The monocot grasses have similar amounts of G and S units with significantly higher amounts of H-units than the hard or soft wood plant species [32]. These compositional changes in plant cell wall and differences in ultrastructure greatly influence the pretreatment and the resultant pretreated biomass sugar conversion. For example, ammonia fiber expansion (AFEX) pretreatment process is effective on monocot grasses and herbaceous plant biomass while not as effective on dicots such as poplar and black locust [33, 34]. Also, the same type of biomass harvested from the same field in different years will display changes in biomass composition (due to environmental conditions). This variance poses a challenge in adjusting the processing conditions and directly influences the biofuels yield.

2.1. Feedstocks for Biorefineries

The cost of feedstocks will significantly influence the cost of biofuel production. It is estimated that about 1 billion tons of biomass will be required annually to displace 30% of the US current petroleum consumption. Two reports were prepared by US Department of Energy’s Office of the Biomass Program in 2005 and 2011 to evaluate the availability of 1 billion tons of feedstock in the US, [35, 36]. Three major feedstocks were taken into consideration, namely, forest and wood waste resources (such as poplar); agricultural residues (such as corn, sorghum, oat, barley, wheat, soybean, cotton, and rice straws); and energy crops (hybrid sorghum, energy cane, Miscanthus, switchgrass and native prairie grass, hybrid poplar, willow, eucalyptus, and pine). Yield assumptions were made based on the crop management, soil condition, and climatic conditions. Three different yield increase assumptions (2%, 3%, and 4%) by year were taken into consideration in these studies (Figure 4).

463074.fig.004
Figure 4: Current and project biomass availability in US based on several assumptions. The data for this plot was taken from billion ton study (2011).

In 2012, the total amount of feedstock available was 341 million tons. About 70% of this came from agricultural residues and 30% from forest residues. The forest biomass showed a marginal increase in yield, while the agricultural biomass showed a modest increase with time due to projected improvements in agronomy practices. Energy crop plantations, particularly switchgrass [37, 38], poplar [39], Bermuda grass [40], sweet sorghum [41], and Miscanthus [42, 43], were tested in several test plots and the biomass will be made available in market by 2017. By 2022, dedicated energy crops will be one of the major feedstocks for bioenergy conversion. A challenge will be to convince farmers who cultivate grains for living to switch to bioenergy feedstocks. Farmers can be assured of buy back guarantees to overcome their reluctance and to remove the risk of failure to sell their cultivated products.

The estimated total biomass that may be available in 2030 based on the three different yield increase assumptions (2%, 3%, and 4%) would be 1047, 1164, and 1304 dry tons, respectively. Other potential high yielding biomass feedstocks available for conversion are agave bagasse (tequila industry in Mexico and Australia), Erianthus (a cane variety grown in south Asian countries like India), Napier grass (widely used in Japan as animal feed), date palm (available in Middle Eastern countries and Africa), and oil palm empty fruit bunch (widely available in Indonesia and Malaysia) [44]. In addition to these feedstocks, several industrial wastes such as rice husk, cotton gin waste, wheat dust, orchard and vineyard pruning, and fruit waste could be used as potential feedstocks for producing biofuels and biochemicals. However, these materials are seasonal and need to be available in large quantities to be considered as feedstocks for biorefineries.

2.2. Biomass Harvesting

Biomass harvesting is an energy intensive process that requires large machinery and demands large amounts of fuel for transportation [45]. Different types of machinery are used for harvesting different types of biomass and the cost of harvesting may be influenced by the type of machinery used [46]. Woody biomass is harvested as felled-timber and then chipped or cut in to different lengths, while energy crops are usually harvested in a single pass with three steps, which are cutting, raking, and baling [47]. Agricultural residues are harvested by collecting and baling the biomass residue after harvesting the grains [48]. Most of the moisture conditioning of the agricultural residue is done in the field prior to baling [49]. Soil contamination of biomass is considered as one of the biggest challenges in biomass harvesting. Other key challenges are the moisture content of biomass (influenced by local weather conditions during fall harvest season) and the amount of biomass that can be harvested from the field (dictated by the tilling conditions used and soil requirements to maintain the biomass productivity during the subsequent years) [50].

2.3. Biomass Yield

About one-third of biofuel production cost is associated with biomass cost. The cost of biomass ($ per ton) is directly proportional to the yield (ton per ha) [51], which is influenced by soil fertility, location, and genetics. Many plant breeding and genetic engineering techniques have been applied to increase the yield of several potential energy feedstocks including switchgrass, poplar, forage sorghum, and Miscanthus [52, 53]. The following are gene alterations by which growth can be promoted in different energy crops: (i) photosynthetic genes, (ii) transcription factors, (iii) cell cycle machinery, (iv) hormone metabolism, (v) lignin modification [54], and (vi) micro-RNA. In addition to these genetic manipulations, biomass yield can be improved by manipulating pathways in both abiotic and biotic stress [55, 56]. Some of the potential feedstocks that will be used in biorefineries and their current yield are shown in Table 1. A combination of transgenesis, classical plant breeding, and modern agricultural practices have been shown to increase the yield of biorefinery feedstocks. These genetically modified crops may need to have their safety ensured to gain public acceptance.

tab1
Table 1: Potential lignocellulosic biomass that is available in US and their average yield (dry ton per acre).

3. Biomass Supply Chain and Logistics

The biomass supply chain will include several key processing steps, which are (i) collection, (ii) storage, (iii) preprocessing (densification by compaction, pelleting, and briquetting), (iv) transportation (from field to biorefinery), and (v) postprocessing at the biorefinery [47, 57]. These supply chain steps will directly impact the cost of feedstock delivery. Texture variance, seasonal availability, low bulk density, and distribution over a large area are major challenges in transporting lignocellulosic biomass to biorefineries [58]. The low density of biomass is known to occupy more volume and requires more transportation carrier space and hence is reported to influence the transportation cost. Transportation cost is also influenced by the moisture content, distance from the field to biorefinery, available infrastructure, available on-site technology, and the mode of transportation (rail or road) [59, 60]. It has been documented that the cost of biofuels depends greatly on the biorefinery size, which will require optimization based on the location and feedstock(s) [6163].

3.1. Biomass Densification

Biomass densification is an energy intensive process done after size reduction by traditional milling processes followed by a compaction process to increase the density by severalfold [64]. During the densification process, the biomass is packed through elastic and plastic deformation. Several technologies are currently developed to densify the biomass and among them the screw press is reported to consume the most energy [65]. In order to improve the biomass binding characteristics, milled biomass should be either heated at an elevated temperature (100–130°C) where the lignin melts to act as a natural binder or mixed with external binders like soluble sugars, fat, starch, protein, or lignosulphonate [66]. Lignosulphonates are preferred when biomass pellets are used for thermochemical applications, where they increase the calorific value of the substrate. Since lignin is a recalcitrant molecule that inhibits enzyme and microbes, it should be avoided when the pellets are used for biochemical transformation applications. However, adding external binders is an additional cost for making biomass pellets. Steam conditioning, steam explosion, and AFEX pretreatment also facilitates the lignin that is buried in the biomass to rise to the surface and aids in the densification process. In addition to temperature, milling speed and pressure are key parameters that need to be optimized to get high quality pellets [67]. Besides these another densification method that is widely used in the industry is the agglomeration technique [68]. It is important to note that different feedstocks pelletize differently and may require different size and thickness of pellet dies [69].

3.2. Centralized versus Decentralized Biomass Processing

Feedstock location is limited to 50 mile radius for the economic operation of a biorefinery that processes 2000 tons biomass/day (Figure 5(a)). Since biomass has a low bulk density and should not be stored at facilities with high moisture content [70, 71], it is more logical to process the biomass (size reduction, pretreatment, and densification) near the field and store them [72, 73] in a decentralized processing facility. Densified biomass with less than 10% moisture will be stable for several months and requires a smaller foot print for storage. This is also advantageous to the biorefinery since feedstock can be transported when needed, resulting in guaranteed feedstock supply all through the year. The concept of regional biomass processing depots (RBPDs) or in other words cooperative systems owned by farmers that process the biomass was first proposed by researchers at Michigan State University [74]. This cooperative model was extensively studied by the University of Tennessee Biofuel Initiative and benefited Dupont cellulosic ethanol (DCE) and the Idaho National Laboratory (INL) by supplying different and mixed feedstocks [75]. The RBPD model can also be expanded to produce other coproducts like lignin, bio-oil, biochar, torrefied biomass, and proteins and could be integrated for in-house energy production using biogas generation [76]. Setting up RBPDs near the cultivation site will generate jobs and will enable construction of infrastructure in rural areas. Although the agriculture cultivation is seasonal, using integrated processing will support operations throughout the year. Life cycle analysis has shown that processing the biomass in RBPDs (decentralized operation) and transporting it to biorefineries reduces greenhouse gas emissions when compared to transporting it to a centralized biorefinery [77, 78].

fig5
Figure 5: Biomass transportation in a centralized and decentralized biorefinery operation (a). Various forms of biomass that will be used in a 2000 ton per day biorefinery and how many times the truck has to transport this biomass is shown (b). Moisture content of each of this biomass is given inside the bars.

There are several challenges in establishing an RBPD, which include (i) identifying energy requirements for the size reduction, pretreatment, and densification operation that will require additional investment to create the infrastructure, (ii) disadvantage of a small scale operation due to economy of scale, and (iii) establishment of the facility near rail lines or creating new rail lines may be required for economic transportation of biomass [74, 75]. For RBPDs a dry-to-dry pretreatment process such as AFEX, disk milling, extrusion is advantageous compared to wet pretreatment processes that may require large amounts of water such as dilute acid, steam explosion, and hot water pretreatment [73].

3.3. Biomass Transportation

Woody biomass can be transported in four different forms: whole tree residue, wood chip, bundle, and pellet. Agricultural biomass can be transported as loose, chopped, baled (square or round), or pelleted forms. The density of the biomass can significantly change depending on the level of processing that the feedstock undergoes [79, 80]. When compared to loose biomass, the density of pellets can increase as high as 10 times for agricultural biomass and 8 times for woody biomass (Figure 5(b)). One option available to transport biomass is by trucks. The dimensions of heavy duty trucks can vary from place to place. For a base case scenario, the pay load (maximum load) of a truck is assumed to have a max of 22.7 tons at a volume of 70 m3 [81]. This truck could carry 5.1, 9.2, 11.2, and 22.7 tons of agricultural biomass (loose, chopped, baled, and pelleted, resp.), or 6.7, 16.8, 14.2, and 22.7 tons of forest residues (chipped, bundled, and pelleted woody biomass, resp.). Assuming that a biorefienry requires about 2000 tons of biomass/day for making biofuels and biochemical [61], transporting agricultural biomass or woody biomass as pellets would require 88 trips/day versus loose biomass, which would take 392 and 298 trips/day for agricultural biomass and woody biomass, respectively. The cost of biomass transportation is expressed as a fixed cost ($ per ton) and variable cost ($ per ton km) using round trip distance (km). The cost of transportation will be higher as the distance from the biorefinery to biomass storage location increases [57].

3.4. Biomass Storage

Harvested biomass can be protected from rain by storing in a building or by covering using a polythene wrap before being shipped to the biorefinery. Biomass feedstocks are vulnerable to microbe aided decomposition facilitated by the moisture present in the biomass after harvesting [82]. When the moist biomasses are stored under aerobic condition in the shed or covered with polythene tarp, several aerobic microbes including fungal infestation could take place. This could possibly reduce the sugar content of the biomass [83]. Storing biomass at <10% moisture (dry weight basis) is recommended for long term stability. In contrast, 20–30% moisture is recommended during biomass pellet making. Hence, biomass should be dried before and after densification (harvested biomass has >30% moisture) [60]. Furthermore, precautionary measures are necessary to prevent self-ignition of biomass during storage [84].

4. Biomass Pretreatment

Lignocellulosic biomass is a complex matrix comprised of cellulose (35–50%), hemicellulose (20–35%), lignin (15–20%), and other minor components [ash, protein, minerals, pectin, etc.] (15–20%) [85, 86]. Biomasses from plants are naturally recalcitrant, having evolved to protect themselves against invading microorganisms. In the wild, when the plants die, they are decomposed by microbes under moist conditions. However, since plant biomasses are recalcitrant, the rate of decomposition is slow and may take several months to years to completely degrade dead plants. On the other hand, in a biorefinery, conversion of biomass to biofuels has to be done in days. In order to increase the accessibility of cellulose and hemicellulose, the hemicellulose-lignin complex cross-links must be broken. Many pretreatment processes have been developed to accomplish this step.

Prominent pretreatment methods include (i) physical pretreatment (size reduction by grinding, milling [87], extrusion at elevated temperature [88], etc.); (ii) chemical pretreatment under alkaline conditions (AFEX [89], ammonia percolation process (ARP) [90], soaking aqueous ammonia (SAA) [91], NaOH [92], alkaline hydrogen peroxide [93], lime [94], alkaline wet oxidation [95], steam explosion under alkaline condition, etc.), neutral conditions (ionic liquid [96] liquid hot water [97], ozonolysis [98], super critical water), or acidic conditions (dilute sulfuric acid [99], organic acid [100, 101], concentrated acid [102], organosolv under acidic condition [103], SPORL [104], etc.); (iii) physiochemical pretreatment (steam explosion under acidic conditions [105], super critical CO2 [106, 107]; and (iv) biological pretreatment [108, 109]. Excellent reviews have been published in the past five years explaining different pretreatment options that have been developed and have potential for commercialization [110116]. Rather than going into the details of the processing steps, the conditions used during the pretreatment process and the advantages and disadvantages of each process are given in Table 2.

tab2
Table 2: Different pretreatment technologies used in biorefinery and their advantages and disadvantages.

Not all pretreatments are created equal. Pretreatment processes that show potential commercialization should satisfy most of the criteria below.(i)A pretreatment process that opens up the cell wall and brings lignin to the surface has the potential to efficiently densify after pretreatment without adding any external binding agents and therefore is ideal for decentralized biomass processing. This will also help to increase the durability of biomass for long term storage. Some of the pretreatments that can fall under this category include AFEX, wet oxidation, and extrusion at elevated temperature.(ii)Densified pretreated biomass that has dual application (fertilizer, soil amendments, animal feed, and biomass composites) in addition to using them as biorefinery feedstock can penetrate the market quickly.(iii)Pretreatment processes that generate lesser amount of degradation products, which are toxic for downstream processing, namely, enzyme hydrolysis and microbial fermentation. Processes that generate large amount of toxic degradation products require large amount of water to remove the toxins from the pretreated biomass making the process more expensive.(iv)Pretreatment processes that can be scaled up to meet the biorefinery needs of handling more than 2000 tons per day or more. The capital cost of pretreatment reactor could increase rapidly based on the pretreatment conditions and the catalyst used. For example, in microwave radiation [117], gamma irradiation required specialized reactor system and also should undergo several additional safety regulations before this technology could get commercialized. Acid pretreatment requires hastelloy reactors to overcome corrosion, while most other pretreatments require reactors made of stainless steel.(v)Pretreatment processes that use less energy because less energy results in less processing cost and vice versa.(vi)Pretreatment processes that use cheap chemicals. Using an expensive chemical like ionic liquid requires additional recovery step which can dramatically increase the processing cost of pretreatment.(vii)Preservation of lignin during pretreatment. Portion of lignin will be used to create heat and electrical energy to drive different processing steps in biorefinery. Pretreatments like alkaline hydrogen peroxide and ozonolysis have the tendency to degrade lignin and hence the energy density of lignin will reduce.(viii)Pretreatments done at moderate temperatures and pressures are highly preferred. This has implications on the cost of the reactor and the safety measures that companies have to take before these technologies can be implemented. Some of the pretreatment processes that use supercritical fluids (water and CO2) operate at a very high pressure and require additional cost while building the reactors.(ix)Using less hazardous chemicals is preferred. For example, chemicals like hydrofluoric acids should undergo additional safety steps to avoid accidents during biomass processing, which will increase the processing cost.(x)Catalyst recovery during pretreatment process is very important for the environment. Although this will slightly increase the processing cost, there will be energy savings overall, since less amount of chemicals will be used during the process. Moreover, most of the catalyst (acid or base) is soluble in water and end up in the waste stream. They should be neutralized with a base or an acid for salt formation. Since most of the biorefinery will be reusing the water, removing these salts from the water will eventually increase the processing cost.

Pretreatment can drastically change the properties of the pretreated material (specific surface area, cellulose crystallinity index, degree of polymerization, lignin content in biomass, acetyl content in biomass, etc.). Effective pretreatments increase the rate of enzyme hydrolysis and significantly decrease the amount of enzymes needed to convert the biomass into sugars, which can be utilized by microorganisms. Since lignin is highly recalcitrant and is responsible for unproductive binding of enzymes, the efficiency of conversion of sugar is influenced by the amount of lignin present in pretreated biomass. Removing lignin during the pretreatment process will enable recovery and reuse of enzymes resulting in significant cost savings.

4.1. Physical Pretreatment

Physical pretreatments include mechanical processing and extrusion where the objective is to reduce the particle size but increase the surface area. For example, disk milling/grinding results in particle sizes of 0.2–2 mm and chipping results in particle sizes of 10–30 mm [118]. Extrusion processes subject the biomass to mixing and shear forces by extruding the biomass under elevated temperatures. The extrusion processes result in shortening of fiber and defibrillation, which increases the accessibility to enzymes during hydrolysis [119]. Grinding and chipping will be adopted in the biomass processing centers prior to thermochemical pretreatment of biomass. Other milling processes include ball milling, hammer milling, and colloid milling. All of these milling processes are highly energy intensive and are unlikely to be used in a biorefinery context.

4.2. Chemical Pretreatment

Chemical pretreatments are carried out at acidic, neutral, or basic conditions. Under acidic conditions (using mineral acids such as H2SO4, HCl, H3PO4, and HNO3 or organic acids like fumaric, maleic, and acetic acid), hemicellulose is solubilized to monomeric xylose leaving the cellulose and lignin behind. The cellulose can then be enzymatically digested to monomeric sugars [120]. The concentration of acid, the pretreatment temperature, and residence time will influence the formation of degradation products like HMF, furfural, and several phenolic lignins, which are inhibitory for downstream processing (enzyme hydrolysis and microbial fermentation). Organic acids are known to produce less degradation products when compared to mineral acids. Pretreatment at neutral conditions are carried out by using ionic liquid (IL). IL is a promising pretreatment process capable of solubilizing both cellulose and hemicellulose that can then be regenerated using antisolvents like water or organic solvents. The cost of IL and catalyst required for pretreatment are major bottlenecks preventing commercialization of this technology [121, 122]. Organosolv is another pretreatment process that can be carried out either at neutral or acidic conditions using organic solvents like methanol, ethanol, acetone, ethylene glycols, and tetrahydrofurfuryl alcohol. Acidic organosolv processes are preferred and when carried out as two-stage process can efficiently fractionate the biomass into hemicellulose, lignin, and cellulose [123]. Other prominent neutral pretreatments include ozonolysis (using ozone as a catalyst to break down lignin), wet oxidation (using oxygen in the presence of Na2CO3), microwave assisted pretreatment, and hot water pretreatment (using water at higher liquid to solid ratio resulting in solubilization of hemicellulose as oligomeric sugars).

Alkaline pretreatments effectively swell and increase the internal surface area of cellulose, decrease crystallinity, cleave lignin carbohydrate complexes (L-C-C), and solubilize lignin. During this process, minor amounts of hemicellulose and cellulose [124] are solubilized. Alkaline processes produce lower amounts of sugar degradation products when compared to acidic pretreatment processes. Some of the prominent alkaline pretreatment processes employ catalysts such as NaOH, KOH, ammonia, or lime. The pretreatment is either done at low temperature for a long residence time or at elevated temperature for a short residence time. The former pretreatment processing conditions are more economical, while the later processing conditions are expensive but could handle larger volume of samples in a short period of time. Strong alkali species like NaOH and KOH cleave ester and ether bonds, while weak alkali species like ammonia cleave only ester bonds. In some cases, oxidants like oxygen or hydrogen peroxide are used to improve the performance of the pretreatment by efficiently removing lignin [125]. AFEX pretreatment is a dry-to-dry process depositing most of the cleaved lignin near the surface of the biomass and does not have any liquid stream generation during the process [126].

Two other prominent physiochemical pretreatment processes widely used are steam explosion (in the presence or absence of SO2) [127] and CO2 explosion (using super critical CO2 that produces carbonic acid). Instead of a single step steam explosion (1.2 MPa/8 min), a two-step steam explosion (1.1 Mpa/4 min and intermediate separation of fiber cell—1.2 Mpa/4 min) was found to increase the sugar conversion during enzyme hydrolysis by 13% and also improved fermentation [128]. The SO2 catalyzed steam explosion process utilizes both chemical (by hydrolyzing acetyl groups that are present in hemicellulose) and physical (by disrupting fibers during explosive release of pressure) effects. Though this process has been successfully demonstrated on hard wood and herbaceous residues, it is not as effective for soft woods [118]. The CO2 explosion is reported to be more cost-effective and produce lesser degradation products when compared to steam explosion [129]. However, both the processes require high pressure reactors that can significantly increase reactor and processing costs.

4.3. Biological Pretreatment

Microorganisms like brown, white, and soft-rot fungi are used to pretreat biomass in the biological pretreatment process. Microbes are very effective in degrading lignin with the help of lignin degrading enzymes (peroxidases and laccases) [130]. Biological pretreatments are operated at mild conditions and require low capital costs when compared to expensive reactor systems required for physical/chemical pretreatment processes. However, the biological process is a relatively slow process requiring several days to pretreat the biomass. Furthermore, the sugar conversion after the microbial pretreatment process is lower when compared to chemical pretreatment. In many cases, biological pretreatment followed by chemical pretreatment is found to be effective and requires less severity pretreatment conditions for effectively hydrolyzing the biomass [131].

4.4. Catalyst Recovery

Most of the catalysts (either acid or base) used in the pretreatment processes are miscible in water and end up in the waste water stream. Recovering catalysts from the dilute water stream is an energy intensive and expensive process. Either chemical precipitation or an expensive ultrafiltration method is used to recover the catalyst. In some cases, the catalysts used in the process are very low in concentration (e.g., dilute sulfuric acid, dilute ammonium hydroxide, etc.) and in such cases catalyst recovery is not necessary. Neutralizing the waste water generated during pretreatment process with acid or base addition results in salt formation. These salts can cause additional cost when recycling the water for subsequent processing steps. The above considerations are not necessary for pretreatment processes using ammonia [132, 133]. Since ammonia is a volatile alkali, it can be recovered and reused as in the AFEX process. When organic solvents (e.g., ethanol in organosolv pretreatment process) are used they have to be recovered using energy intensive distillation processes. In the case of mechanical processing, microwave processing, wet oxidation, ozonolysis, hot water, supercritical water, or carbon dioxide usage, there is no catalyst involved and hence there is no expensive catalyst recovery step required. However, these processes need expensive reactor systems. Using phosphoric acid pretreatments results in formation of highly digestible amorphous cellulose, however, recovery of phosphoric acid from water is a very expensive process [134].

4.5. Influence of Pretreatment on Cellulose Crystallinity and Sugar Conversion

Plant cell wall consists of macromolecule cellulose Iβ which is tightly packed with glucan chains that are held together with inter- and intramolecular hydrogen bonding [135]. The glucan chain length can change anywhere between 100 and 10,000 glucose units, depending on the source of plant biomass [126, 136]. Because of the close packing of the glucan chain (two-chain monoclinic unit cell), the cellulose microfibril is found to be highly recalcitrant. Most of the pretreatments listed in Table 2 result in marginal increase in cellulose crystallinity with some reduction in the degree of polymerization. Some pretreatments result in changes in the crystal structure (different polymorph of cellulose). These changes in the crystal structure happen during pretreatments using chemicals like NaOH, IL [137, 138] (cellulose II), ammines and ammonia (at higher ammonia to biomass ratio greater than 3 : 1) (cellulose IIII) [135, 136], and glycerol (cellulose IV) [139]. Pretreatment using 85% phosphoric acid results in the formation of amorphous cellulose [134]. The cellulose crystal packing greatly influences the rate of enzyme hydrolysis (cellulose IV > cellulose III > cellulose II > cellulose I). In the case of cellulose IV, the hydrogen bonding is completely distorted and the enzymes are able to depolymerize the cellulose [28]. Cellulose III has distorted crystal packing exposing the hydroxyl group to the surface and making it more hydrophilic than cellulose I, which allows the enzyme to remove efficiently and bind to the cellulose. It is widely believed that when more enzymes bind to the cellulose substrate, the conversion will also be more.

4.6. Influence of Pretreatment and Degradation Products on Downstream Processing

To allow enzymes to have easy access to the sugar polymers, pretreatment helps to open up the complex plant cell wall. During the pretreatment process, different chemicals are used as catalysts to cleave chemical linkages (ester and ether) and release small organic molecules. The most prominent small molecules that are produced during hydroxyl ion based ester linkage cleavage are acetic acid, ferulic acid, and coumaric acid. Corresponding amides are produced if ammonium ion is responsible for cleaving the ester linkages. Other prominent aliphatic acids that are produced include formic, lactic, succinic, fumaric, aconitic, levulinic, and itaconic acids. Some of the lignin degraded products include vanilic, caffeic, syringic, and synaptic benzoic acids. Aldehydes released during pretreatment include vanillin, 4-hydroxyacetophenone, 4-hydroxybenzaldehyde, and 3,4-dihydroxylbenzaldehyde [33]. The most prominent sugar degradation products produced during acid hydrolysis include 2-furoic acid, 4-hydroxymethyl furfural, and furfural. It has been estimated that the amount of degradation products produced during acid pretreatments is two times higher than alkaline pretreatments [140]. The concentration of the degradation compounds could significantly change if the severity (higher temperature, higher catalyst concentration, and longer residence time) of the pretreatment changes. These degradation compounds have been found to inhibit enzymes during hydrolysis and microbes during the fermentation processes.

It is impossible to avoid degradation product formation during pretreatment. Hence, researchers are trying to identify enzymes and microbes that are less inhibited by these compounds or to develop methods to remove these compounds by using water or solvent based extractions. In the case of acid pretreatment, expensive detoxification steps are followed prior to microbial fermentation [141, 142]. They include passing the hydrolysate through activated charcoal (which absorbs organic compounds) or raise the pH to 10 and then reduce to 5 to precipitate degradation compounds as in overliming. However, these additional processes add cost and are not practical in scaled up biorefineries. Another promising approach to consider is to remove the degradation products and lignin molecules using the extractive ammonia pretreatment process [143]. In this case, appropriate cosolvents are added along with the ammonia during the pretreatment thereby increasing the solvent to biomass ratio from 3 : 1 to 6 : 1. Depending on the type of solvent and water used in the process, some hemicellulose is lost during the pretreatment. However, up to 45% of lignin can be removed by this approach. Other prominent pretreatment that removes lignin are ionic liquid, organosolv, and ARP processes.

5. Enzyme Hydrolysis

Microorganisms secrete enzymes to degrade biomass for producing monomeric sugars for their own survival. There are two ways microbes use the biomass degrading enzymes in a natural environment. The first is cellulosomal enzyme system (a complex mixture of enzymes that are docked to cohesive and doctrine domains which are anchored on the surface of the organisms) [144]. The second is the free enzyme system (where enzymes are secreted as individual components) to act on biomass substrates [145]. The free enzyme system is easy to duplicate and is widely used for biomass conversion in biorefineries. Free biomass degrading enzymes are produced in large scale by commercial companies using fungus or bacteria. The microbes are fed with agricultural residues (grains, hulls, and several biomass waste generated in the industry). This cocktail contains 40–50 different biomass degrading enzymes which can be classified into three major categories: cellulases (which degrade cellulose), hemicellulase (which degrade hemicellulose), and pectinase (which degrade pectin) [146]. Cellulase constitutes about 70–85% of the cocktail and hemicellulose and pectinase constitute the remaining 15–30% depending on the organisms and choice of substrate. Another class of enzyme that could also play an important role in biomass deconstruction is ligninases (which degrades lignin).

Different types of enzymes are needed to cleave different types of bonds during hydrolysis of lignocellulosic biomass due to the complex network of cellulose and hemicellulose [147]. Such enzymes are called molecular scissors and produce specific monomeric sugars from complex carbohydrates. Several excellent articles have been published in the past documenting specific activities of each enzyme and how they work synergistically during hydrolysis [148151]. For example, cellobiohydrolase I (CBHI) acts on the reducing end of cellulose chains, cellobiohydrolase II (CBHII) act on the nonreducing end of cellulose chains, endoglucanase (EG) act on the amorphous region of cellulose, and beta-glucosidase (βG) act on cellobiose to produce monomeric glucose. To be most effective, individual enzymes need to be present in the appropriate ratio due to their synergistic nature. Trichoderma reseei (a filamentous fungus) produces high concentrations of enzymes up to 100 g/L and is widely used by commercial companies to produce biomass-degrading enzymes (Novozyme and Genencor) [152]. Other thermophilic fungal and bacterial enzymes have recently been introduced to the market, which perform at higher temperatures to prevent Lactobacillus (converts sugars to lactic acid) contamination [153, 154].

5.1. Cost of Enzymes

The enzyme quantity required to hydrolyze lignocellulosic biomass is onefold higher than for starch. This is primarily because lignocellulosic biomass is naturally recalcitrant with a complex ultrastructure. Lignin in plant cell wall and degradation products produced during pretreatment are responsible for deactivating enzymes and hence increased amounts of enzymes are required [155]. In the past decade, commercial enzyme companies have made significant progress in producing new generations of enzymes with higher specific activities and lower cost using different biotechnology and process engineering approaches [156]. However, technoeconomic analyses have shown that more progress needs to be made. The cost of enzymes is one of the driving factors for current research [157]. Already several approaches have been adopted to produce highly active enzymes. These include (i) identifying novel multifunctional enzymes that can hydrolyze different types of polysaccharide linkages [158], (ii) identifying novel enzymes that have superior activity [159], (iii) producing novel enzymes using different genetic engineering approaches [160], and (iv) direct evolution of enzymes [161]. Another novel approach is expressing enzymes in plants that could be extracted and used after pretreating the extracted biomass for producing fermentable sugars [162]. Enzymes could also be produced directly in biorefineries rather than producing them in a centralized location. Producing enzymes on-site at biorefineries would eliminate the need for concentration, storage, and shipping and could reduce the production costs by using pretreated substrates already available at the biorefinery [163].

5.2. Enzymatic Hydrolysis Time

The time taken to completely hydrolyse biomass to monomeric sugars depends on several factors: lignin content in biomass [164], pretreatment effectiveness [136, 165], cellulose crystallinity [166], substrate concentration, and enzyme activity. Removing hemicellulose during pretreatment (dilute acid, acid catalyzed steam explosion, organosolv, and phosphoric acid pretreatment) significantly reduces the recalcitrance of biomass allowing for a fast rate of sugar conversion [166168]. When looking at the rate of enzymatic hydrolysis on AFEX pretreated corn stover (where there is no hemicellulose removal), biphasic kinetics are present with a fast hydrolysis phase that produces 70% sugar conversion in the first 24 hours and then a slow hydrolysis phase requiring more than 6 days to completely depolymerize the remaining complex carbohydrates. To eliminate the problem of long hydrolysis times, a new process engineering approach was developed where the biomass is initially hydrolyzed for 24 hours. After 24 hours, the sugars are removed and fermented separately, while the residual solids requiring further hydrolysis time are added to fresh pretreated substrate in the same tank along with fresh enzymes for further hydrolysis. This approach can significantly help reduce the biomass to sugar processing time [169].

5.3. Enzyme Recycling

Since biomass degrading enzymes are expensive, they need to be recycled to reduce the processing cost. Most of the cellulases have cellulose binding modules (CBMs), which anchor the enzymes to the substrate to facilitate cellulose hydrolysis. This allows unhydrolyzed solids (UHS) obtained after enzymatic hydrolysis to be efficiently used for recycling enzymes [169, 170]. However, there are certain limitations of using this method. Most accessory enzymes lack CBMs (βG, xylanase, xylosidase, etc.) and act on soluble substrates. Also, even enzymes with cellulose binding modules (CMBs) will eventually desorb from the substrate after a certain period of time [171]. Furthermore, enzymes can be deactivated due to thermal denaturation or shear stress. These enzyme activities will be lost after hydrolysis. When the recycled solids with bound enzymes are used for subsequent cycle of hydrolysis, they will have different enzyme profile than the one initially used. This will significantly affect the enzyme synergy during hydrolysis and will reduce the sugar conversion. Other common methods that have been used to recycle the enzymes include immobilized enzymes on nanoparticles or polymeric matrices [172, 173], ion exchange adsorption [174], and ultrafiltration [175].

5.4. Effect of Solid Loadings on Sugar Conversion

Enzyme conversion rate is dependent on the solid loading used during hydrolysis. It is important to note that monomeric sugars, oligomeric sugars, and degradation products produced during pretreatment also inhibit the enzymes. Most of the enzymatic hydrolysis are done to optimize pretreatment conditions [176179] or to check enzymes activities are usually done at low solid loadings (1% glucan or 3% solid loadings). Under these conditions, the total inhibitor concentration is relatively low allowing for higher sugar conversion. As the solid loading increases, the enzyme inhibitor concentration also increases causing a drop in sugar yield (g sugar/g biomass) [122, 180]. Reduced sugar yield negatively impacts process economics. Hence, the sugar concentration and yield should be taken into account such that it is well balanced to obtain the best economics [181]. This is true for almost all pretreated substrates [182]. Also, fibers in pretreated biomass have the natural capacity to absorb water. Therefore, as the solid loading increases most of the water will be absorbed by the biomass requiring high energy to mix the biomass. Inefficient mixing creates mass transfer issues and results in lower sugar conversion. In order to avoid this problem, pretreated biomass samples are added in batches to allow enough time for the enzymes to solubilize the biomass [183]. Also, it has been reported that the power consumption during hydrolysis is influenced by the viscosity of the hydrolyzate [184].

Particle size also plays an important role during high solid loading hydrolysis [185]. Small particles result in increased surface area, which increases sugar conversion [186]. However, producing small particles requires more energy and can create issues when mixing. Small particles can agglomerate during high solid loadings, which reduces the water activity and consequently sugar conversion. A significant change in rheological properties was reported when using different sized particles during hydrolysis [187, 188]. In recent studies increased sugar conversion was evident when the particle size was increased, possibly due to reduced agglomeration and viscosity caused by the large particles [189]. These phenomena promote better mixing and allow for better sugar conversion.

5.5. Unproductive Oligosaccharide Production

After enzymatic hydrolysis, 15–25% of the released sugars are in the form of gluco- and xylo-oligosaccharides. As the solid loading increases, the concentration of oligomeric sugar also increases due to inhibition from high concentrations of monomeric sugar and degradation products. In the pretreatment processes that do not solubilize hemicellulose (e.g., dilute ammonia pretreatment, AFEX, etc.), more xylo-oligomers are present than gluco-oligomers. These oligomeric sugars are considered unproductive as most of the microbes used in the fermentation can consume only monomeric sugars [190]. The reason for accumulation of oligomeric sugars is unknown. Several manuscripts tend to provide explanation for such accumulation by the separation and characterization of these oligomeric sugars [191, 192]. Some possible reasons for accumulation are (i) enzyme inhibition due to degradation products and monomeric sugars, (ii) chemical modification of glucan and xylan chains during pretreatment, (iii) lack of key accessory enzymes in the enzyme cocktail that cleave specific linkages, and (iv) the presence of phenolic compounds attached to the end of the glucan chains. Furthermore, xylo-oligomers that are produced during initial stages of enzyme hydrolysis are reported to strongly inhibit biomass-degrading enzymes [193] and are considered to be responsible for oligosaccharide accumulation.

6. Microbial Fermentation

Microbial fermentations convert sugars produced from lignocellulosic biomass into biofuels (e.g., ethanol, butanol, acetone, isobutanol, lipids, etc.,) or biochemicals (e.g., organic acids) using fungus, yeast, or bacteria (Table 3). This process can be performed separately from enzymatic hydrolysis (separate hydrolysis and fermentation [SHF]), in combination with enzymatic hydrolysis (simultaneous saccharification and fermentation [SSF]), or combine enzyme production and enzymatic hydrolysis (consolidated bioprocessing [CBP]) [194]. Fermentation of glucose and xylose can be carried out separately or in combination (cofermentation, where both glucose and xylose are simultaneously converted). These strains do not naturally consume xylose but are made capable through genetic modification. Butanol production was previously commercialized through ABE (acetone, butanol, and ethanol) fermentation from molasses using the anearobic bacterium Clostridium acetobutylicum [195]. Currently, attempts are being made to produce butanol from lignocellulosic biomass either using native C. acetobutylicum strains or genetically modified S. cerevisiae or Escherichia coli strains [196, 197]. Some microbes like oleaginous yeasts and some algae are capable of accumulating lipids up to 75% of their body mass by consuming both glucose and xylose [198201]. Lipids can be used to make biodiesel using transesterification process. However, lipid fermentation for fuel production based on current technology is not economical based on recently published economic analysis studies [202]. However, high-value fatty acids could potentially be a coproduct that could make biorefinery process economical [203].

tab3
Table 3: Examples of microbial strains that are used for biofuel production.

6.1. Microbes for Producing Biofuels

Cofermentation is believed to be superior than separate fermentation in terms of cost savings. Many of challenging efforts have been made to genetically modify Saccharomyces cerevisiae and Zymomonas mobilis to enable fermentation of xylose. Two xylose-fermenting pathways have been widely studied and engineered into S. cerevisiae (Figure 6), namely, (i) xylose reductase (XR), xylitol dehydrogenase (XDH) pathway that exists in fungi [204, 205] and (ii) xylose isomerase (XI) pathway that exists in bacteria [206]. These two pathways convert xylose to xylulose. Xylulose is then converted to xylulose-5-phosphate which is further converted through either pentose phosphate pathway or phosphoketolase pathway [207] (Figure 6). The XR-XDH pathway, however, creates a redox imbalance under anaerobic conditions because XR prefers NADPH as the reaction cofactor, while XDH solely uses NAD+. Some microbes, such as E. coli and Scheffersomyces stipitis (a.k.a. Pichia stipitis) [208, 209], can natively ferment xylose. However, they typically have limitations, which reduce their effectiveness compared to S. cerevisiae or Z. mobilis. For instance, E. coli cannot tolerate high concentrations of inhibitors (degradation products and biofuels) [209] and on the other hand S. stipiti has a low ethanol metabolic yield [210]. Another strategy adopted by Microbiogen (http://www.microbiogen.com/) involves fermenting glucose to ethanol under anaerobic conditions and converting xylose to yeast biomass under aerobic conditions using a native S. cerevisiae strain MBG3248, which was screened and adapted for propagation on xylose [211]. This strategy produced 173 liters of ethanol and 134 kg of yeast protein from one ton of corn stover using dilute acid pretreatment technology.

463074.fig.006
Figure 6: Two possible xylose metabolic pathways that are commonly used in yeast and bacteria.

Lignocellulosic biomass can also be directly fermented to biofuels by CBP microbes, such as Clostridium thermocellum [212] and Clostridium phytofermentans. C. thermocellum is a thermophilic anaerobic bacterium, which ferments at around 60°C. It produces an enzyme complex (cellulosome) to degrade cellulose, which has been shown using pure cellulose samples to be more efficient than free enzymes [213]. The fermentation products generated by C. thermocellum are mostly ethanol and acetic acid [213]. C. thermocellum is a very promising CBP microbe but is limited by its low tolerance to fermentation products [214]. C. phytofermentans is a mesophilic and an anaerobic bacterium. It produces free enzymes to degrade cellulose and hemicelluloses and can consume almost all the sugars present in the lignocellulosic biomass [215]. The main product after sugar fermentation is ethanol along with acetic acid as the minor product. C. phytofermentans also has a low tolerance for fermentation products [216]. CBP yeast is another focus area for researchers. The idea is to transfer novel cellulase and hemicellulase genes into a biofuel producing yeast strain (e.g., S. cerevisiae). Several research works have been performed and published on this topic [213, 217219]. White-rot fungi have also been investigated as potential CBP microbes. Recently, Phlebia sp. MG-60 was reported to convert 20 g/L unbleached hardwood Kraft pulp into 8.4 g/L ethanol with an ethanol yield of 0.42 g/g pulp (71.8% of the theoretical maximum) [220].

6.2. Challenges in Sugar Utilization (Glucose versus Xylose Uptake)

Currently, SHF is still the major process configuration for lignocellulosic biofuel production. Cofermentation microorganisms are also widely used to ferment enzymatic hydrolysate that contains both glucose and xylose. While glucose fermentation is very rapid, xylose fermentation is much slower. For instance, in a typical 6% glucan loading AFEX corn stover hydrolysate, 60 g/L glucose can be converted to ethanol by a xylose-fermenting yeast S. cerevisiae 424A in less than 18 hours, but the 30 g/L xylose takes an additional 96 hours to be converted to ethanol [221]. The slow xylose fermentation has been quantitatively studied by Jin et al. [209] and the reasons for such slow utilization is in part because S. cerevisiae does not have specialized xylose transporters so that xylose transportation relies on glucose transporters. However, glucose transporters have a high affinity to glucose and a low affinity to xylose. Therefore, glucose fermentation by S. cerevisiae (and most other microorganisms) always occurs prior to xylose fermentation. A considerable amount of biofuel (e.g., ethanol) present in the fermentation broth after the glucose consumption has high potential to inhibit the xylose fermentation metabolism. In addition to ethanol, other fermentation metabolites that are generated during glucose fermentation can play a critical role in inhibiting xylose fermentation. Moreover, due to the redox imbalance issue during xylose fermentation by S. cerevisiae 424A, the yeast cannot grow during xylose fermentation [222]. As a result, the viable cells decrease during xylose fermentation further slowing fermentation. Degradation products also reduce the specific xylose fermentation rate resulting in a reduced fermentation rate [209]. Other prominent S. cerevisiae strains include TMB3400 [223]; GLBRC Y35 [224]; RWB218 [225]; and DA24-16BT3 [226] (Table 3). Other S. cerevisiae strains produce other biofuels such as isobutanol [209, 227]; N-butanol/isobutanol [226, 228]; N-butanone/secondary butanone/isobutanol [229, 230]; and isoprenoids [230]. Some microbial strains, in some cases, consume glucose and xylose at the same time (without glucose catabolite repression) during fermentation (e.g., Thamnidium elegans under aerobic conditions) [231].

6.3. Separation of Biofuels from Fermentation Broth

Traditionally, distillation is used to separate alcohol and water. Distillation can generate a maximum of 95% pure ethanol. Molecular sieves or additives are then needed to break the azeotrope to get pure ethanol. Although simple, distillation is an energy intensive process and requires initial ethanol concentrations greater than 4% to be economical [232]. Mostly grains or extracted sugar is used in the first generation biorefinery and therefore there are almost no degradation products in the substrate to inhibit enzymes or microbes. Hence, ethanol titer >10% are easily achievable allowing an economical distillation process. Researchers are looking at different biofuels that are insoluble in water that can be phase separated to avoid distillation process [233].

6.4. In Situ Biofuel Separation to Improve Fermentation Performance

Since biofuels are known to inhibit microbes during fermentation, a large number of studies have been conducted to remove biofuels during the fermentation process. The most commonly used in situ biofuel removal methods are pervaporation and gas-striping methods. Pervaporation is a membrane-based separation technology using a nonporous or porous, hydrophilic or organophilic membrane [234]. Before the pervaporation step, there is typically a filtration step to remove microbial cells from the fermentation broth, which are then recycled back to the fermentor. The filtration step is critical because pervaporation typically operates at a temperature much higher than that tolerated by the microbial cells [235]. A fermentation broth is in contact with one side of the membrane while a vacuum or gas purge is imposed on the other side. The biofuel molecules in the fermentation broth are evaporated through the membrane (Figure 7). The pervaporated fermentation broth is then recycled back to the fermentor. Although pervaporation is a promising technology, the cost is currently higher than distillation. Vane [236] pointed out several aspects that needed to be addressed before pervaporation can become cost competitive, including energy efficiency, capital cost reduction for the pervaporation system, longer term trials using actual fermentation broths, and integration of pervaporation with fermenter. Membrane fouling by fermentation broth components is another concern when carrying out pervaporation [237].

463074.fig.007
Figure 7: Two commonly used methods for separating ethanol from fermentation broth other than traditional distillation method in a biorefinery.

Gas-stripping is a relatively simple process where a gas (normally nitrogen or carbon dioxide) is sparged through the fermentation broth at a high flow rate. The volatile biofuel molecules will equilibrate with the stripping gas and is passed out of the fermenter. Gas-stripping does not affect fermenting microorganisms or remove media components and is compatible with continuous fermentation processes [238]. The following are issues with gas-stripping for biofuel application: (i) large equipment cost, (ii) high energy costs to condense the stripped biofuel, (iii) increase in fermenter size, and (v) foam formation [239]. Both pervaporation and gas-stripping have been widely applied to ethanol and butanol fermentations documenting improved fermentation performance [237, 239, 240]. For instance, de Vrije et al. applied gas-stripping to remove fermentation products (isopropanol, butanol, and ethanol) during Clostridium beijerinckii fermentation that resulted in improved productivity [239]. Gas-stripping was also shown to greatly improve sugar utilization. For example, in a study of acetone butanol ethanol (ABE) fermentation coupled with gas-stripping, 199 g/L sugar was utilized and 69.7 g/L solvent was produced compared to sugar utilization of only 30 g/L in a control batch reactor [238].

7. Coproduct Generation and Its Influence of Biofuel Production Cost

Coproduct generation is very essential for producing cost competitive biofuels. For example, the first generation corn ethanol industry consists of 67% dry mill based and 33% wet mill based operations. Coproducts generated depend on the mill type [17]. Though the dry mill process produces more ethanol (2.8 gallon/bushels of corn) than the wet mill process (2.5 gallon/bushels of corn), the wet mill produces more coproducts, which results in more revenue. The corn dry mill industry produces dry distiller’s grains and soluble (DDGS) and carbon dioxide as major coproducts reducing the biofuel cost by 35% [241]. In the corn wet milling process, high capital and energy intensive processing is involved (fractionating grain into starch, fiber, gluten, and germ) to produce a larger number of coproducts that include carbon dioxide, corn oil, corn gluten meal, and corn gluten feed. For the second generation technology to be able to compete with the first generation technology, several coproducts should be generated that can be sold for a high market price and subsequently reducing the overall processing costs of biofuels [242]. Some of the coproducts that could be generated from second generation biorefinery are discussed below [243].

7.1. Lignin

Lignin is a randomly linked aromatic polymer and constitutes about one-third of lignocellulosic biomass. Currently, the pulp and paper industry produces considerable amount of lignin that are mostly used to generate heat and power for the plant. The only product that has been successfully produced from lignin at large commercial scale is vanillin [244], which currently competes with vanillin that is produced using petrochemicals [245]. Other minor products that are produced using lignin include Bakelite (hard plastic used as utensil handles), resins and filler materials in plastic industry. With the development of several novel catalytic [246249] or pyrolytic route [250, 251], economic uses for lignin could appear in the near future. Different pretreatments could generate different types of lignin. Removing the lignin during the pretreatment also improves downstream processing (both hydrolysis and microbial fermentation). For example, organosolv process could isolate high purity lignin [252], while other pretreatment processes like steam explosion and dilute acid pretreatment generate highly condensed lignin that could be used for producing energy products (e.g., binders for making biomass pellet, or bricket). Reliable and high quality processed lignin with adequate functionalities could be used as precursors for several products, including carbon fiber, bio-oil, resins, adhesives, polymer fillers, coating agents, plastics, paints, soil amendment, slow nitrogen release fertilizers, rubbers, elastomers, and antimicrobial agents [252254]. However, several fractionation steps are needed to remove other components in biomass extractive (like proteins, carbohydrates) to generate pure lignin [253, 254]. If the lignin is not extracted during pretreatment, it ends up as UHS after enzymatic hydrolysis. If a portion of this could be separated into a valuable lignin stream, extra revenue could be generated for the biorefinery instead of simply burning all the UHS to provide energy for the processing steps.

7.2. Protein

Protein is another potential coproduct that could be separated and sold in the second generation biorefinery. Most biomass contains about 2–5% of crude protein and several early harvest grasses (e.g., switchgrass, Miscanthus, Napiergrass, etc.) contain 10–15% of crude protein [255]. Though several process technologies are already in place for separating the protein [256], it is economically challenging to separate crude protein from dilute water stream. Alkali as the pretreatment chemical is more favorable than acids for protein extraction [243]. Another alternative is to use proteases that cleave the proteins into amino acids. It has been estimated that when second generation biorefineries are ready to replace 10% of fossil fuels, about 100 MT/year of proteins could be produced [257]. It is widely believed that this protein could be used as a low value animal feed. There is also the potential for converting the proteins into amino acids which could be converted into organic compounds and used as precursors for synthesizing industrial products. A prominent example is the conversion of L-arginine to 1, 4-diaminobutane (precursor for Nylon 4–6) using a two-step enzymatic process [258].

7.3. Microbial Biomass

One of the potential coproducts in a biorefinery is microbial biomass [118]. In the batch fermentation mode, part of the microbe could be reused for the subsequent fermentation process [259]. The remaining biomass could be sold as an animal feed if using a native organism. Since most of the microbes used for fermentation in the second generation biorefineries are genetically modified organisms (that could efficiently consume both glucose and xylose) there may be some potential regulations for the use of microbial biomass as animal feed. In the semicontinuous rapid bioconversion with integrated recycle technology (RaBIT) process, the same concept may apply [169], where in the microbial cells are recycled every 24 hours for subsequent fermentation cycle. Excess cells are used for other applications. Furthermore, separated cells will contain several lignin degraded products and may lower the quality of feed [260]. Processing the proteins from these organisms followed by converting them to amino acids by acid hydrolysis is another option that could be used to produce chemicals, which can be used as precursors for making biomaterials.

8. Biofuels Economy of Scale and Cost

Using key process parameters developed by national renewable energy laboratory (NREL) on biomass conversions, several cost models have been developed in the past to understand the required capital investments [261264]. With various assumptions in place, when plant capacity (0–15,000 ton per day) was plotted against total production cost ($ m−3), it was found that a biorefinery should handle more than 2000–5000 ton per day in order to be economical (850–875 $ m−3). Plants that operated at more than 5000 ton per day showed a marginal increase in the production cost [265]. However some research findings have shown that there is a steady decrease in the minimum ethanol selling price from 3.75 to 2.25 ($/gallon) as the plant size increased from 500 to 10,000 dry ton per day [266]. The cost analysis is based on several factors like biomass transportation distance, type of biomass used, type of processing technology used, efficiencies of different processing steps, type of biofuel, and coproducts production.

9. Water Requirement in a Biorefinery and the Necessity for Recycling

Producing biofuels using the sugar platform is a water intensive process. Water is used in almost all the processing steps. In order to meet the water requirements, important decisions should be made regarding the location of the biorefineries. In many cases, water will be pumped from the ground, which may add considerable stress to the local water resources [267, 268]. Recycling water will help to reduce this stress, but will require additional investment. Given the process and processing conditions used in the biorefineries, it will be a prerequisite to do the following when recycling the water: remove salts generated during neutralization, remove organic content, and recycle the catalysts [267]. Clarification steps have been widely adopted in the pulp and paper industry to remove suspended solids and to reduce chemical oxygen demand/biochemical oxygen demand in water. Several novel technologies have been developed to treat the water, which include biological treatment (e.g., anaerobic digestion, algal treatment), coagulation, electrocoagulation, polymer resin filtration, and coagulation-flocculation techniques. Among these techniques, coagulation (using ferric sulphate, alum, water soluble polymers, chitosan, poly aluminum chloride, fly ash, etc.) is found to be an economical approach to remove organics [269]. It is important to use minimal water in each processing step in order to reduce water recycling cost. In some cases, the choice of pretreatment in a second generation biorefinery will be determined based on the water availability in the region. Colocating the second and the first generation biorefineries will minimize waste water and reduce the stress on the water table [152, 270].

10. Environmental Issues

It is well reported that biofuels offers several environmental benefits over fossil fuels. Biofuels from lignocellulosic biomass have reduced emissions and fixed CO2, a greenhouse gas, among other things [271]. In the near future when a new biorefinery is established, several technologies will be assembled based on their impact on the environment [272]. Some of the examples are air pollution caused by particulate emission during biomass harvesting and grinding, noise pollution from explosive pretreatment processes, methods for producing pretreatment chemicals that produce GHG emissions, and release of pretreatment chemicals to the environment after processing. Life cycle analysis (LCA) is often used to assess the net environmental impact of these processing steps [273, 274]. The challenges are in carrying out accurate LCA analysis depending on the data that is collected from group of aligned processes that will be used in the biorefinery. Many companies are taking the LCA very seriously to assess the environment impact so that they could make decisions to adjust the process or areas that needed to be focused to reduce the emissions. Depending on the emissions estimated by LCA will influence the cost of establishing the biorefinery.

11. Energy Associated with Biomass Processing

The goal of establishing a biorefinery is to produce energy in the form of liquid transportation fuels from biomass [275]. Therefore, it is very important to maximize the difference in energy consumed and produced. In other words, the success of a biorefinery will be evaluated by the net energy that is produced using the different processing steps [276]. Efficiencies will need to be closely monitored to maximize the net gain in the energy produced in the biorefinery [277279]. It is widely reported in several technoeconomic evaluations of second generation biorefineries that lignin will be a good energy source for different processing steps. However, the UHS that are rich in lignin are obtained as wet slurry and will need to be dried before gasified or burned to produce energy. Hydrothermal pyrolysis is one potential technology which can use wet biomass slurry to produce bio-oil and use the heat recovered for several processing steps [280]. If lignin is extracted during pretreatment and used for producing high value products, the biorefineries will have to generate energy by burning part of the biomass that arrive at biorefineries [281]. It is widely believed that natural gas will be the primary source of energy to run biorefineries, and as the technology matures, the amount of natural gas usage will be slowly brought down. Colocating biorefineries near thermal plants (coal or nuclear plant) or using energy from renewable resources (wind, solar, geothermal, etc.) is another option to get heat and power [282]. Adding an anaerobic digestion facility adjacent to a biorefinery will be beneficial that could clean waste water and at the same time the biogas generated could be used for different biorefinery operations [283, 284].

12. Conclusion

This review highlighted several bottlenecks that are being faced by big corporations to commercialize the biofuel production technology (pretreatment, hydrolysis, microbial fermentation, and biofuel separation). Big corporations and oil companies that have capital to establish a new biorefinery are currently trying to align different novel process technologies that still have several separation and purification challenges to overcome [285]. The choice of pretreatment and lignocellulosic biomass could be decided based on the availability of sufficient quantity of catalyst and feedstock in that region. The aligned technologies are currently scaled up to establish pilot plants to demonstrate the feasibility. Simultaneously, biomass logistics and technoeconomic evaluations are carried out to assess the technology readiness level (TRL). Then assessments are made regarding the environment impact of using different technologies. Once appropriate feedstock, pretreatment, and enzymes are combined to produce cheap sugars, the choice of biofuels and biochemicals depends on the market demand and more importantly the biofuel policy defined by the local and federal government. Furthermore, in order to compete with the cost of petroleum fuels, the cost of biofuel processing should be kept as low as possible using energy efficient technologies and using less water. Producing as many coproducts as possible in a biorefinery will help to reduce the cost of biofuel production. If favorable conditions prevail after overcoming these hurdles, then a high capital of about 200–300 million dollars is required to establish a commercial grade biorefinery that could produce several million gallon of ethanol per year. It is important that a biorefinery should be established in an appropriate location that has good water resources, access to feedstocks, and energy that is needed to process the feedstock. Few big corporations (e.g., Abengoa, Dupont, and Poet) are putting all their resources to first establish the lignocellulosic biorefinery and then overcome all the bottlenecks to reduce the processing cost. Once this is done, then the group of technologies will be sublicensed to different biofuel manufactures. Only at this stage one can anticipate large amounts of biofuels entering the market to achieve the mandate set by DOE and USDA. To facilitate this biofuel production process, several millions of dollars are currently provided by the government to stimulate large scale biofuel production. In the past five years, only a few companies have been successful in demonstrating their technology in their pilot scales and are now gradually progressing to establish their commercial plants. Based on the public information that is available, it looks like lignocellulosic ethanol will first hit the US market, later followed by several advanced biofuels (e.g., butanol, alkanes, etc.). Due to the challenges discussed in this paper, it is anticipated that there may be a considerable delay in the commercial availability of lignocellulosic biofuels from the previously projected timeline of 2022 by the USDA and DOE.

Conflict of Interests

The author declares that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The author thanks Great Lakes Bioenergy Research Center (https://www.glbrc.org/), financial support by the DOE, Office of Science, Office of Biological and Environmental Research, through Cooperative Agreement DEFC02-07ER64494 between the Board of Regents of the University of Wisconsin System and the DOE. The author would like to thank Dr. Mingjie Jin, Michigan State University, who was instrumental in shaping up this review. The author also thanks Ms. Sumathi Venkatesh, Dr. Sunil Nityanand, and Mr. Cory Sarks from Michigan State University for helping to revise the paper and giving their valuable suggestions.

References

  1. S. N. Naik, V. V. Goud, P. K. Rout, and A. K. Dalai, “Production of first and second generation biofuels: a comprehensive review,” Renewable and Sustainable Energy Reviews, vol. 14, no. 2, pp. 578–597, 2010. View at Publisher · View at Google Scholar · View at Scopus
  2. A. Demirbas, “Biofuels securing the planet's future energy needs,” Energy Conversion and Management, vol. 50, no. 9, pp. 2239–2249, 2009. View at Publisher · View at Google Scholar · View at Scopus
  3. D. S. J. Jones and P. R. Pujadó, Handbook of Petroleum Processing, Springer, New York, NY, USA, 2006.
  4. REN21-Renewable Energy Policy Network for the 21st century, http://www.ren21.net/REN21Activities/GlobalStatusReport.aspx.
  5. A. Mohr and S. Raman, “Lessons from first generation biofuels and implications for the sustainability appraisal of second generation biofuels,” Energy Policy, vol. 63, pp. 114–122, 2013. View at Publisher · View at Google Scholar
  6. International Energy Agency (IEA), World Energy Outlook World Energy Outlook, International Energy Agency, Paris, France, 2007.
  7. R. A. Lee and J.-M. Lavoie, “From first- to third-generation biofuels: challenges of producing a commodity from a biomass of increasing complexity,” Animal Frontiers, vol. 3, no. 2, pp. 6–11, 2013. View at Publisher · View at Google Scholar
  8. H. C. Greenwell, M. Loyd-Evans, and C. Wenner, “Biofuels, science and society,” Interface Focus, vol. 3, pp. 1–4, 2012.
  9. R. D. Perlack, L. L. Wright, A. F. Turhollow, R. L. Graham, B. J. Stokes, and D. C. Erbach, Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply, U.S. Department of Energy & U.S. Department of Agriculture, Oak Ridge, Tenn, USA, 2005.
  10. T. M. Mata, A. A. Martins, and N. S. Caetano, “Valorization of waste frying oils and animal fats for biodiesel production,” in Advanced Biofuels and Bioproducts, chapter 4, pp. 671–693, Springer, Berlin, Germany, 2013.
  11. N. A. Buijs, V. Siewers, and J. Nielsen, “Advanced biofuel production by the yeast Saccharomyces cerevisiae,” Current Opinion in Chemical Biology, vol. 17, no. 3, pp. 480–488, 2013. View at Publisher · View at Google Scholar
  12. C. A. Rabinovitch-Deere, J. W. K. Oliver, G. M. Rodriguez, and S. Atsumi, “Synthetic biology and metabolic engineering approaches to produce biofuels,” Chemical Reviews, vol. 113, no. 7, pp. 4611–4632, 2013. View at Publisher · View at Google Scholar
  13. C. M. Gowen and S. S. Fong, “Applications of systems biology towards microbial fuel production,” Trends in Microbiology, vol. 19, no. 10, pp. 516–524, 2011. View at Publisher · View at Google Scholar · View at Scopus
  14. M. A. Martin, “First generation biofuels compete,” New Biotechnology, vol. 27, no. 5, pp. 596–608, 2010. View at Publisher · View at Google Scholar · View at Scopus
  15. S.-T. Yang and M. Yu, “Integrated biorefinery for sustainable production of fuels, chemicals, and polymers,” in Bioprocessing Technologies in Biorefinery for Sustainable Production of Fuels, Chemicals, and Polymers, S.-T. Yang, H. A. El-Enshasy, and N. Thongchul, Eds., vol. 1st, John Wiley & Sons, New York, NY, USA, 2013.
  16. G. R. Timilsina and A. Shrestha, “How much hope should we have for biofuels?” Energy, vol. 36, no. 4, pp. 2055–2069, 2011. View at Publisher · View at Google Scholar · View at Scopus
  17. R. J. Bothast and M. A. Schlicher, “Biotechnological processes for conversion of corn into ethanol,” Applied Microbiology and Biotechnology, vol. 67, no. 1, pp. 19–25, 2005. View at Publisher · View at Google Scholar · View at Scopus
  18. K. A. Rosentrater, “A review of corn masa processing residues: generation, properties, and potential utilization,” Waste Management, vol. 26, no. 3, pp. 284–292, 2006. View at Publisher · View at Google Scholar · View at Scopus
  19. B. Kamm, M. Kamm, P. R. Gruber, and S. Kromus, “Biorefinery systems—an overview,” in Biorefineries-Industrial Processes and Products: Status Quo and Future Directions, B. Kamm, P. R. Gruber, and M. Kamm, Eds., vol. 1, Wiley-VCH, New York, NY, USA, 2006.
  20. F. Cherubini and S. Ulgiati, “Crop residues as raw materials for biorefinery systems—a LCA case study,” Applied Energy, vol. 87, no. 1, pp. 47–57, 2010. View at Publisher · View at Google Scholar · View at Scopus
  21. R. E. H. Sims, W. Mabee, J. N. Saddler, and M. Taylor, “An overview of second generation biofuel technologies,” Bioresource Technology, vol. 101, no. 6, pp. 1570–1580, 2010. View at Publisher · View at Google Scholar · View at Scopus
  22. V. Balan, S. Kumar, B. Bals, S. P. S. Chundawat, M. Jin, and B. E. Dale, “Biochemical and thermochemical conversion of switchgrass to biofuels,” in Switchgrass: A Valuable Biomass Crop for Energy, A. Monti, Ed., chapter 7, pp. 153–186, Springer, London, UK, 2012.
  23. V. Balan, D. Chiaramonti, and S. Kumar, “Review of US and EU initiatives towards development, demonstration and commercialization of lignocellulosic biofuels,” Biofuels, Bioproducts and Biorefining, vol. 7, no. 6, pp. 732–759, 2013. View at Publisher · View at Google Scholar
  24. M. A. Carriquiry, X. Du, and G. R. Timilsina, “Second generation biofuels: economics and policies,” Energy Policy, vol. 39, no. 7, pp. 4222–4234, 2011. View at Publisher · View at Google Scholar · View at Scopus
  25. S. K. Hoekman, “Biofuels in the U.S.—challenges and opportunities,” Renewable Energy, vol. 34, no. 1, pp. 14–22, 2009. View at Publisher · View at Google Scholar · View at Scopus
  26. V. Menon and M. Rao, “Trends in bioconversion of lignocellulose: biofuels, platform chemicals & biorefinery concept,” Progress in Energy and Combustion Science, vol. 38, no. 4, pp. 522–550, 2012. View at Publisher · View at Google Scholar · View at Scopus
  27. L. Luo, E. van der Voet, and G. Huppes, “Biorefining of lignocellulosic feedstock—technical, economic and environmental considerations,” Bioresource Technology, vol. 101, no. 13, pp. 5023–5032, 2010. View at Publisher · View at Google Scholar · View at Scopus
  28. V. Balan, B. Bals, L. D. Souse, R. Garlock, and B. E. Dale, “A short review on ammonia based lignocelluloses' biomass pretreatment,” in Chemical and Biochemical Catalysis for Next Generation Biofuel, B. Simmons, Ed., RSC Energy and Environment Series no. 4, chapter 5, pp. 89–114, Royal Society of Chemistry, 2011.
  29. G. Tao, T. A. Lestander, P. Geladi, and S. Xiong, “Biomass properties in association with plant species and assortments I: a synthesis based on literature data of energy properties,” Renewable and Sustainable Energy Reviews, vol. 16, no. 5, pp. 3481–3506, 2012. View at Publisher · View at Google Scholar · View at Scopus
  30. S. V. Vassilev, D. Baxter, L. K. Andersen, and C. G. Vassileva, “An overview of the chemical composition of biomass,” Fuel, vol. 89, no. 5, pp. 913–933, 2010. View at Publisher · View at Google Scholar · View at Scopus
  31. S. V. Vassilev, D. Baxter, L. K. Andersen, C. G. Vassileva, and T. J. Morgan, “An overview of the organic and inorganic phase composition of biomass,” Fuel, vol. 94, pp. 1–33, 2012. View at Publisher · View at Google Scholar · View at Scopus
  32. W. Boerjan, J. Ralph, and M. Baucher, “Lignin biosynthesis,” Annual Review of Plant Biology, vol. 54, pp. 519–546, 2003. View at Publisher · View at Google Scholar · View at Scopus
  33. V. Balan, L. da Costa Sousa, S. P. S. Chundawat et al., “Enzymatic digestibility and pretreatment degradation products of AFEX-treated hardwoods (Populus nigra),” Biotechnology Progress, vol. 25, no. 2, pp. 365–375, 2009. View at Publisher · View at Google Scholar · View at Scopus
  34. R. J. Garlock, Y. S. Wong, V. Balan, and B. E. Dale, “AFEX pretreatment and enzymatic conversion of black locust (Robinia pseudoacacia L.) to soluble sugars,” Bioenergy Research, vol. 5, no. 2, pp. 306–318, 2012. View at Publisher · View at Google Scholar · View at Scopus
  35. “Biomass as Feedstock for a Bioenergy and Bioproducts Industry: The Technical Feasibility of a Billion-Ton Annual Supply,” 2005, http://www1.eere.energy.gov/bioenergy/pdfs/final_billionton_vision_report2.pdf.
  36. “U.S. Billion-Ton Update: Biomass Supply for a Bioenergy and Bioproducts Industry,” 2011, http://www1.eere.energy.gov/bioenergy/pdfs/billion_ton_update.pdf.
  37. S. Sokhansanj, S. Mani, S. Turhollow et al., “Large-scale production, harvest and logistics of switchgrass (Panicum virgatum L.)—current technology and envisioning a mature technology,” Biofuels, Bioproducts and Biorefining, vol. 3, no. 2, pp. 124–141, 2009. View at Publisher · View at Google Scholar · View at Scopus
  38. K. David and A. J. Ragauskas, “Switchgrass as an energy crop for biofuel production: a review of its ligno-cellulosic chemical properties,” Energy and Environmental Science, vol. 3, no. 9, pp. 1182–1190, 2010. View at Publisher · View at Google Scholar · View at Scopus
  39. P. Sannigrahi, A. J. Ragauskas, and G. A. Tuskan, “Poplar as a feedstock for biofuels: a review of compositional characteristics,” Biofuels, Bioproducts and Biorefining, vol. 4, no. 2, pp. 209–226, 2010. View at Publisher · View at Google Scholar · View at Scopus
  40. J. Xu, Z. Wang, and J. J. Cheng, “Bermuda grass as feedstock for biofuel production: a review,” Bioresource Technology, vol. 102, no. 17, pp. 7613–7620, 2011. View at Publisher · View at Google Scholar · View at Scopus
  41. W. Zegada-Lizarazu and A. Monti, “Are we ready to cultivate sweet sorghum as a bioenergy feedstock? A review on field management practices,” Biomass and Bioenergy, vol. 40, pp. 1–12, 2012. View at Publisher · View at Google Scholar · View at Scopus
  42. H. W. Zub and M. Brancourt-Hulmel, “Agronomic and physiological performances of different species of Miscanthus, a major energy crop. A review,” Agronomy for Sustainable Development, vol. 30, no. 2, pp. 201–214, 2010. View at Publisher · View at Google Scholar · View at Scopus
  43. F. G. Dohleman and S. P. Long, “More productive than maize in the Midwest: how does Miscanthus do it?” Plant Physiology, vol. 150, no. 4, pp. 2104–2115, 2009. View at Publisher · View at Google Scholar · View at Scopus
  44. C. Somerville, H. Youngs, C. Taylor, S. C. Davis, and S. P. Long, “Feedstocks for lignocellulosic biofuels,” Science, vol. 329, no. 5993, pp. 790–792, 2010. View at Publisher · View at Google Scholar · View at Scopus
  45. P. McKendry, “Energy production from biomass (part 1): overview of biomass,” Bioresource Technology, vol. 83, no. 1, pp. 37–46, 2002. View at Publisher · View at Google Scholar · View at Scopus
  46. S. Thorsell, F. M. Epplin, R. L. Huhnke, and C. M. Taliaferro, “Economics of a coordinated biorefinery feedstock harvest system: lignocellulosic biomass harvest cost,” Biomass and Bioenergy, vol. 27, no. 4, pp. 327–337, 2004. View at Publisher · View at Google Scholar · View at Scopus
  47. S. Sokhansanj and J. R. Hess, “Biomass supply logistics and infrastructure,” in Biofuels: Methods and Protocols, J. R. Mielenz, Ed., vol. 581 of Methods in Molecular Biology, chapter 1, pp. 1–25, Springer, Berlin, Germany, 2009.
  48. R. L. Hoskinson, D. L. Karlen, S. J. Birrell, C. W. Radtke, and W. W. Wilhelm, “Engineering, nutrient removal, and feedstock conversion evaluations of four corn stover harvest scenarios,” Biomass and Bioenergy, vol. 31, no. 2-3, pp. 126–136, 2007. View at Publisher · View at Google Scholar · View at Scopus
  49. J. R. Hess, K. L. Kenney, C. T. Wright, R. Perlack, and A. Turhollow, “Corn stover availability for biomass conversion: situation analysis,” Cellulose, vol. 16, no. 4, pp. 599–619, 2009. View at Publisher · View at Google Scholar · View at Scopus
  50. D. R. Huggins, R. S. Karow, H. P. Collins, and J. K. Ransom, “Introduction: evaluating long-term impacts of harvesting crop residues on soil quality,” Agronomy Journal, vol. 103, no. 1, pp. 230–233, 2011. View at Publisher · View at Google Scholar · View at Scopus
  51. M. D. Duffy and V. Y. Nanhou, Switchgrass Production in Iowa: Economic Analysis, Special Publication for Cahriton Valley Resource Conservation District, Iowa State University Extension Publication, Iowa State University, 2002.
  52. C. A. Rojas, A. S. Hemerly, and P. C. G. Ferreira, “Genetically modified crops for biomass increase. Genes and strategies,” GM Crops, vol. 1, no. 3, pp. 137–142, 2010. View at Scopus
  53. J. G. Dubouzet, T. J. Strabala, and A. Wagner, “Potential transgenic routes to increase tree biomass,” Plant Science, vol. 212, pp. 72–101, 2013. View at Publisher · View at Google Scholar
  54. R. Vanholme, K. Morreel, C. Darrah et al., “Metabolic engineering of novel lignin in biomass crops,” New Phytologist, vol. 196, no. 4, pp. 978–1000, 2012. View at Publisher · View at Google Scholar
  55. M. Sticklen, “Plant genetic engineering to improve biomass characteristics for biofuels,” Current Opinion in Biotechnology, vol. 17, no. 3, pp. 315–319, 2006. View at Publisher · View at Google Scholar · View at Scopus
  56. P. Bhatnagar-Mathur, V. Vadez, and K. K. Sharma, “Transgenic approaches for abiotic stress tolerance in plants: retrospect and prospects,” Plant Cell Reports, vol. 27, no. 3, pp. 411–424, 2008. View at Publisher · View at Google Scholar · View at Scopus
  57. A. Sultana, A. Kumar, and D. Harfield, “Development of agri-pellet production cost and optimum size,” Bioresource Technology, vol. 101, no. 14, pp. 5609–5621, 2010. View at Publisher · View at Google Scholar · View at Scopus
  58. A. C. Caputo, M. Palumbo, P. M. Pelagagge, and F. Scacchia, “Economics of biomass energy utilization in combustion and gasification plants: effects of logistic variables,” Biomass and Bioenergy, vol. 28, no. 1, pp. 35–51, 2005. View at Publisher · View at Google Scholar · View at Scopus
  59. A. Kumar, S. Sokhansanj, and P. C. Flynn, “Development of a multicriteria assessment model for ranking biomass feedstock collection and transportation systems,” Applied Biochemistry and Biotechnology, vol. 129, no. 1–3, pp. 71–87, 2006. View at Publisher · View at Google Scholar · View at Scopus
  60. P. C. Badger, “Biomass transport systems,” in Encyclopedia of Agricultural, Food and Biological Engineering, vol. 1, pp. 94–98, 2003.
  61. A. Kumar, J. B. Cameron, and P. C. Flynn, “Biomass power cost and optimum plant size in western Canada,” Biomass and Bioenergy, vol. 24, no. 6, pp. 445–464, 2003. View at Publisher · View at Google Scholar · View at Scopus
  62. A. Kumar, J. B. Cameron, and P. C. Flynn, “Pipeline transport and simultaneous saccharification of corn stover,” Bioresource Technology, vol. 96, no. 7, pp. 819–829, 2005. View at Publisher · View at Google Scholar · View at Scopus
  63. A. Kumar and S. Sokhansanj, “Switchgrass (Panicum vigratum, L.) delivery to a biorefinery using integrated biomass supply analysis and logistics (IBSAL) model,” Bioresource Technology, vol. 98, no. 5, pp. 1033–1044, 2007. View at Publisher · View at Google Scholar · View at Scopus
  64. S. Mani, L. G. Tabil, and S. Sokhansanj, “Specific energy requirement for compacting corn stover,” Bioresource Technology, vol. 97, no. 12, pp. 1420–1426, 2006. View at Publisher · View at Google Scholar · View at Scopus
  65. J. S. Tumuluru, C. T. Wright, J. R. Hess, and K. L. Kenney, “A review of biomass densification systems to develop uniform feedstock commodities for bioenergy application,” Biofuels, Bioproducts and Biorefining, vol. 5, no. 6, pp. 683–707, 2011. View at Publisher · View at Google Scholar · View at Scopus
  66. N. Kaliyan and R. V. Morey, “Natural binders and solid bridge type binding mechanisms in briquettes and pellets made from corn stover and switchgrass,” Bioresource Technology, vol. 101, no. 3, pp. 1082–1090, 2010. View at Publisher · View at Google Scholar · View at Scopus
  67. Z. Miao, T. E. Grift, A. C. Hansen, and K. C. Ting, “Energyrequirement for lignocellulosic feedstock densifications in relation to particle physical properties, preheating, and binding agents,” Energy Fuels, vol. 27, no. 1, pp. 588–595, 2013. View at Publisher · View at Google Scholar
  68. P. R. Mort, “Scale-up and control of binder agglomeration processes—flow and stress fields,” Powder Technology, vol. 189, no. 2, pp. 313–317, 2009. View at Publisher · View at Google Scholar · View at Scopus
  69. R. Samuelsson, M. Thyrel, M. Sjöström, and T. A. Lestander, “Effect of biomaterial characteristics on pelletizing properties and biofuel pellet quality,” Fuel Processing Technology, vol. 90, no. 9, pp. 1129–1134, 2009. View at Publisher · View at Google Scholar · View at Scopus
  70. E. Audsley and J. E. Annetts, “Modelling the value of a rural biorefinery—part I: the model description,” Agricultural Systems, vol. 76, no. 1, pp. 39–59, 2003. View at Publisher · View at Google Scholar · View at Scopus
  71. J. E. Annetts and E. Audsley, “Modelling the value of a rural biorefinery—part II: analysis and implications,” Agricultural Systems, vol. 76, no. 1, pp. 61–76, 2003. View at Publisher · View at Google Scholar · View at Scopus
  72. F. You and B. Wang, “Life cycle optimization of biomass-to-liquid supply chains with distributed-centralized processing networks,” Industrial and Engineering Chemistry Research, vol. 50, no. 17, pp. 10102–10127, 2011. View at Publisher · View at Google Scholar · View at Scopus
  73. J. K. Kurian, G. R. Nair, A. Hussain, and G. S. V. Raghavan, “Feedstocks, logistics and pre-treatment processes for sustainable lignocellulosic biorefineries: a comprehensive review,” Renewable and Sustainable Energy Reviews, vol. 25, pp. 205–219, 2013. View at Publisher · View at Google Scholar
  74. J. E. Carolan, S. V. Joshi, and B. E. Dale, “Technical and financial feasibility analysis of distributed bioprocessing using regional biomass pre-processing centers,” Journal of Agricultural and Food Industrial Organization, vol. 5, no. 2, pp. 1–29, 2007. View at Scopus
  75. B. Sharma, R. G. Ingalls, C. L. Jones, and A. Khanchi, “Biomass supply chain design and analysis: basis, overview, modeling, challenges, and future,” Renewable and Sustainable Energy Reviews, vol. 24, pp. 608–627, 2013. View at Publisher · View at Google Scholar
  76. P. L. Eranki and B. E. Dale, “Comparative life cycle assessment of centralized and distributed biomass processing systems combined with mixed feedstock landscapes,” GCB Bioenergy, vol. 3, no. 6, pp. 427–438, 2011. View at Publisher · View at Google Scholar
  77. P. L. Eranki, B. D. Bals, and B. E. Dale, “Advanced regional biomass processing depots: a key to the logistical challenges of the cellulosic biofuel industry,” Biofuels, Bioproducts and Biorefining, vol. 5, no. 6, pp. 621–630, 2011. View at Publisher · View at Google Scholar · View at Scopus
  78. A. Egbendewe-Mondzozo, S. M. Swinton, B. D. Bals, and B. E. Dale, “Can dispersed biomass processing protect the environment and cover the bottom line for biofuel?” Environmental Science and Technology, vol. 47, pp. 1695–1703, 2013.
  79. H. An, W. E. Wilhelm, and S. W. Searcy, “A mathematical model to design a lignocellulosic biofuel supply chain system with a case study based on a region in Central Texas,” Bioresource Technology, vol. 102, no. 17, pp. 7860–7870, 2011. View at Publisher · View at Google Scholar · View at Scopus
  80. X. Zhu, X. Li, Q. Yao, and Y. Chen, “Challenges and models in supporting logistics system design for dedicated-biomass-based bioenergy industry,” Bioresource Technology, vol. 102, no. 2, pp. 1344–1351, 2011. View at Publisher · View at Google Scholar · View at Scopus
  81. A. Sultana and A. Kumar, “Optimal configuration and combination of multiple lignocellulosic biomass feedstocks delivery to a biorefinery,” Bioresource Technology, vol. 102, no. 21, pp. 9947–9956, 2011. View at Publisher · View at Google Scholar · View at Scopus
  82. A. A. Rentizelas, A. J. Tolis, and I. P. Tatsiopoulos, “Logistics issues of biomass: the storage problem and the multi-biomass supply chain,” Renewable and Sustainable Energy Reviews, vol. 13, no. 4, pp. 887–894, 2009. View at Publisher · View at Google Scholar · View at Scopus
  83. J. Johansson, J. Liss, T. Gullberg, and R. Björheden, “Transport and handling of forest energy bundles—advantages and problems,” Biomass and Bioenergy, vol. 30, no. 4, pp. 334–341, 2006. View at Publisher · View at Google Scholar · View at Scopus
  84. B. F. Gray, J. F. Griffiths, and S. M. Hasko, “Spontaneous ignition hazards in stockpiles of cellulosic materials: criteria for safe storage,” Journal of Chemical Technology and Biotechnology, Chemical Technology, vol. 34, no. 8, pp. 453–463, 1984. View at Scopus
  85. S. H. Mood, A. H. Golfeshan, M. Tabatabaei et al., “Lignocellulosic biomass to bioethanol, a comprehensive review with a focus on pretreatment,” Renewable and Sustainable Energy Reviews, vol. 27, pp. 77–93, 2013. View at Publisher · View at Google Scholar
  86. M. Pauly and K. Keegstra, “Plant cell wall polymers as precursors for biofuels,” Current Opinion in Plant Biology, vol. 13, no. 3, pp. 305–312, 2010. View at Publisher · View at Google Scholar · View at Scopus
  87. A. Hideno, H. Inoue, K. Tsukahara et al., “Wet disk milling pretreatment without sulfuric acid for enzymatic hydrolysis of rice straw,” Bioresource Technology, vol. 100, no. 10, pp. 2706–2711, 2009. View at Publisher · View at Google Scholar · View at Scopus
  88. J. Yoo, S. Alavi, P. Vadlani, and V. Amanor-Boadu, “Thermo-mechanical extrusion pretreatment for conversion of soybean hulls to fermentable sugars,” Bioresource Technology, vol. 102, no. 16, pp. 7583–7590, 2011. View at Publisher · View at Google Scholar · View at Scopus
  89. F. Teymouri, L. Laureano-Perez, H. Alizadeh, and B. E. Dale, “Optimization of the ammonia fiber explosion (AFEX) treatment parameters for enzymatic hydrolysis of corn stover,” Bioresource Technology, vol. 96, no. 18, pp. 2014–2018, 2005. View at Publisher · View at Google Scholar · View at Scopus
  90. H. K. Tae and Y. Y. Lee, “Pretreatment and fractionation of corn stover by ammonia recycle percolation process,” Bioresource Technology, vol. 96, no. 18, pp. 2007–2013, 2005. View at Publisher · View at Google Scholar · View at Scopus
  91. X. Li, T. H. Kim, and N. P. Nghiem, “Bioethanol production from corn stover using aqueous ammonia pretreatment and two-phase simultaneous saccharification and fermentation (TPSSF),” Bioresource Technology, vol. 101, no. 15, pp. 5910–5916, 2010. View at Publisher · View at Google Scholar · View at Scopus
  92. M. J. Taherzadeh and K. Karimi, “Pretreatment of lignocellulosic wastes to improve ethanol and biogas production: a review,” International Journal of Molecular Sciences, vol. 9, no. 9, pp. 1621–1651, 2008. View at Publisher · View at Google Scholar · View at Scopus
  93. G. Banerjee, S. Car, T. Liu et al., “Scale-up and integration of alkaline hydrogen peroxide pretreatment, enzymatic hydrolysis, and ethanolic fermentation,” Biotechnology and Bioengineering, vol. 109, no. 4, pp. 922–931, 2012. View at Publisher · View at Google Scholar · View at Scopus
  94. J. Xu, J. J. Cheng, R. R. Sharma-Shivappa, and J. C. Burns, “Lime pretreatment of switchgrass at mild temperatures for ethanol production,” Bioresource Technology, vol. 101, no. 8, pp. 2900–2903, 2010. View at Publisher · View at Google Scholar · View at Scopus
  95. S. Banerjee, R. Sen, R. A. Pandey et al., “Evaluation of wet air oxidation as a pretreatment strategy for bioethanol production from rice husk and process optimization,” Biomass and Bioenergy, vol. 33, no. 12, pp. 1680–1686, 2009. View at Publisher · View at Google Scholar · View at Scopus
  96. A. P. Dadi, C. A. Schall, and S. Varanasi, “Mitigation of cellulose recalcitrance to enzymatic hydrolysis by ionic liquid pretreatment,” Applied Biochemistry and Biotechnology, vol. 137–140, no. 1–12, pp. 407–421, 2007. View at Publisher · View at Google Scholar · View at Scopus
  97. Y. Kim, R. Hendrickson, N. S. Mosier, and M. R. Ladisch, “Liquid hot water pretreatment of cellulosic biomass,” in Biofuels: Methods and Protocols, vol. 581 of Methods in Molecular Biology, pp. 93–102, Springer, Berlin, Germany, 2009. View at Publisher · View at Google Scholar
  98. M. T. García-Cubero, G. González-Benito, I. Indacoechea, M. Coca, and S. Bolado, “Effect of ozonolysis pretreatment on enzymatic digestibility of wheat and rye straw,” Bioresource Technology, vol. 100, no. 4, pp. 1608–1613, 2009. View at Publisher · View at Google Scholar · View at Scopus
  99. T. A. Lloyd and C. E. Wyman, “Combined sugar yields for dilute sulfuric acid pretreatment of corn stover followed by enzymatic hydrolysis of the remaining solids,” Bioresource Technology, vol. 96, no. 18, pp. 1967–1977, 2005. View at Publisher · View at Google Scholar · View at Scopus
  100. L. Qin, Z.-H. Liu, B.-Z. Li, B. E. Dale, and Y.-J. Yuan, “Mass balance and transformation of corn stover by pretreatment with different dilute organic acids,” Bioresource Technology, vol. 112, pp. 319–326, 2012. View at Publisher · View at Google Scholar · View at Scopus
  101. F. M. Gírio, C. Fonseca, F. Carvalheiro, L. C. Duarte, S. Marques, and R. Bogel-Łukasik, “Hemicelluloses for fuel ethanol: a review,” Bioresource Technology, vol. 101, no. 13, pp. 4775–4800, 2010. View at Publisher · View at Google Scholar · View at Scopus
  102. M. Galbe and G. Zacchi, “A review of the production of ethanol from softwood,” Applied Microbiology and Biotechnology, vol. 59, no. 6, pp. 618–628, 2002. View at Publisher · View at Google Scholar · View at Scopus
  103. F. Sun and H. Chen, “Organosolv pretreatment by crude glycerol from oleochemicals industry for enzymatic hydrolysis of wheat straw,” Bioresource Technology, vol. 99, no. 13, pp. 5474–5479, 2008. View at Publisher · View at Google Scholar · View at Scopus
  104. H. Liu and J. Y. Zhu, “Eliminating inhibition of enzymatic hydrolysis by lignosulfonate in unwashed sulfite-pretreated aspen using metal salts,” Bioresource Technology, vol. 101, no. 23, pp. 9120–9127, 2010. View at Publisher · View at Google Scholar · View at Scopus
  105. C. Tengborg, K. Stenberg, M. Galbe et al., “Comparison of SO2 and H2SO4 impregnation of softwood prior to steam pretreatment on ethanol production,” Applied Biochemistry and Biotechnology A: Enzyme Engineering and Biotechnology, vol. 70–72, pp. 3–15, 1998. View at Scopus
  106. K. H. Kim and J. Hong, “Supercritical CO2 pretreatment of lignocellulose enhances enzymatic cellulose hydrolysis,” Bioresource Technology, vol. 77, no. 2, pp. 139–144, 2001. View at Publisher · View at Google Scholar · View at Scopus
  107. C. Schacht, C. Zetzl, and G. Brunner, “From plant materials to ethanol by means of supercritical fluid technology,” Journal of Supercritical Fluids, vol. 46, no. 3, pp. 299–321, 2008. View at Publisher · View at Google Scholar · View at Scopus
  108. S. J. Patel, R. Onkarappa, and K. S. Shobha, “Comparative study of ethanol production from microbial pretreated agricultural residues,” Journal of Applied Sciences and Environmental Management, vol. 11, pp. 137–141, 2007.
  109. C. Wan and Y. Li, “Fungal pretreatment of lignocellulosic biomass,” Biotechnology Advances, vol. 30, no. 6, pp. 1447–1457, 2012. View at Publisher · View at Google Scholar · View at Scopus
  110. A. T. W. M. Hendriks and G. Zeeman, “Pretreatments to enhance the digestibility of lignocellulosic biomass,” Bioresource Technology, vol. 100, no. 1, pp. 10–18, 2009. View at Publisher · View at Google Scholar · View at Scopus
  111. L. da Costa Sousa, S. P. Chundawat, V. Balan, and B. E. Dale, “‘Cradle-to-grave’ assessment of existing lignocellulose pretreatment technologies,” Current Opinion in Biotechnology, vol. 20, no. 3, pp. 339–347, 2009. View at Publisher · View at Google Scholar · View at Scopus
  112. J. Y. Zhu, X. Pan, and R. S. Zalesny Jr., “Pretreatment of woody biomass for biofuel production: energy efficiency, technologies, and recalcitrance,” Applied Microbiology and Biotechnology, vol. 87, no. 3, pp. 847–857, 2010. View at Publisher · View at Google Scholar · View at Scopus
  113. V. B. Agbor, N. Cicek, R. Sparling, A. Berlin, and D. B. Levin, “Biomass pretreatment: fundamentals toward application,” Biotechnology Advances, vol. 29, no. 6, pp. 675–685, 2011. View at Publisher · View at Google Scholar · View at Scopus
  114. S. P. S. Chundawat, G. T. Beckham, M. E. Himmel, and B. E. Dale, “Deconstruction of lignocellulosic biomass to fuels and chemicals,” Annual Review of Chemical and Biomolecular Engineering, vol. 2, pp. 121–145, 2011. View at Publisher · View at Google Scholar · View at Scopus
  115. B. E. Dale and R. G. Ong, “Energy, wealth, and human development: why and how biomass pretreatment research must improve,” Biotechnology Progress, vol. 28, no. 4, pp. 893–898, 2012. View at Publisher · View at Google Scholar
  116. E. C. Bensah and M. Mensah, “Chemical pretreatment methods for the production of cellulosic ethanol: technologies and innovations,” International Journal of Chemical Engineering, vol. 2013, Article ID 719607, 21 pages, 2013. View at Publisher · View at Google Scholar
  117. H. Ma, W. W. Liu, X. Chen, Y. J. Wu, and Z. L. Yu, “Enhanced enzymatic saccharification of rice straw by microwave pretreatment,” Bioresource Technology, vol. 100, no. 3, pp. 1279–1284, 2009. View at Publisher · View at Google Scholar · View at Scopus
  118. Y. Sun and J. Cheng, “Hydrolysis of lignocellulosic materials for ethanol production: a review,” Bioresource Technology, vol. 83, no. 1, pp. 1–11, 2002. View at Publisher · View at Google Scholar · View at Scopus
  119. C. Karunanithy, K. Muthukumarappan, and J. L. Julson, “Influence of high shear bioreactor parameters on carbohydrate release from different biomasses,” in Proceedings of the American Society of Agricultural and Biological Engineers Annual International Meeting, ASABE 084114, pp. 3562–3577, ASABE, St. Joseph, Mich, USA, July 2008. View at Scopus
  120. N. Mosier, C. Wyman, B. Dale et al., “Features of promising technologies for pretreatment of lignocellulosic biomass,” Bioresource Technology, vol. 96, no. 6, pp. 673–686, 2005. View at Publisher · View at Google Scholar · View at Scopus
  121. Q. Li, Y. C. He, M. Xian et al., “Improving enzymatic hydrolysis of wheat straw using ionic liquid 1-ethyl-3-methyl imidazolium diethyl phosphate pretreatment,” Bioresource Technology, vol. 100, no. 14, pp. 3570–3575, 2009. View at Publisher · View at Google Scholar · View at Scopus
  122. A. G. Cruz, C. Scullin, C. Mu et al., “Impact of high biomass loading on ionic liquid pretreatment,” Biotechnology for Biofuels, vol. 6, no. 1, article 52, 2013. View at Publisher · View at Google Scholar
  123. M. G. Papatheofanous, E. Billa, D. P. Koullas, B. Monties, and E. G. Koukios, “Two-stage acid-catalyzed fractionation of lignocellulosic biomass in aqueous ethanol systems at low temperatures,” Bioresource Technology, vol. 54, no. 3, pp. 305–310, 1995. View at Publisher · View at Google Scholar · View at Scopus
  124. R. Kumar and C. E. Wyman, “Effects of cellulase and xylanase enzymes on the deconstruction of solids from pretreatment of poplar by leading technologies,” Biotechnology Progress, vol. 25, no. 2, pp. 302–314, 2009. View at Publisher · View at Google Scholar · View at Scopus
  125. F. Carvalheiro, T. Silva-Fernandes, L. C. Duarte, and F. M. Gírio, “Wheat straw autohydrolysis: process optimization and products characterization,” Applied Biochemistry and Biotechnology, vol. 153, no. 1–3, pp. 84–93, 2009. View at Publisher · View at Google Scholar · View at Scopus
  126. S. P. S. Chundawat, B. S. Donohoe, L. da Costa Sousa et al., “Multi-scale visualization and characterization of lignocellulosic plant cell wall deconstruction during thermochemical pretreatment,” Energy and Environmental Science, vol. 4, no. 3, pp. 973–984, 2011. View at Publisher · View at Google Scholar · View at Scopus
  127. Z. Yu, B. Zhang, F. Yu, G. Xu, and A. Song, “A real explosion: the requirement of steam explosion pretreatment,” Bioresource Technology, vol. 121, pp. 335–341, 2012. View at Publisher · View at Google Scholar
  128. Y. Zhang X, Fu, and H. Chen, “Pretreatment based on two-step steam explosion combined with an intermediate separation of fiber cells-optimization of fermentation of corn straw hydrolysates,” Bioresource Technology, vol. 121, pp. 100–104, 2012. View at Publisher · View at Google Scholar
  129. Y. Zheng, H. M. Lin, and G. T. Tsao, “Pretreatment for cellulose hydrolysis by carbon dioxide explosion,” Biotechnology Progress, vol. 14, no. 6, pp. 890–896, 1998. View at Publisher · View at Google Scholar · View at Scopus
  130. O. J. Sánchez and C. A. Cardona, “Trends in biotechnological production of fuel ethanol from different feedstocks,” Bioresource Technology, vol. 99, no. 13, pp. 5270–5295, 2008. View at Publisher · View at Google Scholar · View at Scopus
  131. V. Balan, L. da Costa Sousa, S. P. S. Chundawat, R. Vismeh, A. D. Jones, and B. E. Dale, “Mushroom spent straw: a potential substrate for an ethanol-based biorefinery,” Journal of Industrial Microbiology and Biotechnology, vol. 35, no. 5, pp. 293–301, 2008. View at Publisher · View at Google Scholar · View at Scopus
  132. V. Balan, B. Bals, S. P. S. Chundawat, D. Marshall, and B. E. Dale, “Lignocellulosic biomass pretreatment using AFEX,” in Biofuels: Methods and Protocols, J. R. Mielenz, Ed., vol. 581 of Methods in Molecular Biology, pp. 61–77, Humana Press, Springer Science + Business Media, LLC, 2009.
  133. S. P. S. Chundawat, B. Bals, T. Campbell et al., “Primer on ammonia fiber expansion pretreatment,” in Aqueous Pretreatment of Plant Biomass for Biological and Chemical Conversion to Fuels and Chemicals, C. Wyman, Ed., Wiley Series in Renewable Resources, chapter 9, pp. 169–195, John Wiley & Sons, New York, NY, USA, 1st edition, 2013.
  134. Y.-H. P. Zhang, S.-Y. Ding, J. R. Mielenz et al., “Fractionating recalcitrant lignocellulose at modest reaction conditions,” Biotechnology and Bioengineering, vol. 97, no. 2, pp. 214–223, 2007. View at Publisher · View at Google Scholar · View at Scopus
  135. M. Wada, H. Chanzy, Y. Nishiyama, and P. Langan, “Cellulose IIII crystal structure and hydrogen bonding by synchrotron X-ray and neutron fiber diffraction,” Macromolecules, vol. 37, no. 23, pp. 8548–8555, 2004. View at Publisher · View at Google Scholar · View at Scopus
  136. S. P. S. Chundawat, G. Bellesia, N. Uppugundla et al., “Restructuring the crystalline cellulose hydrogen bond network enhances its depolymerization rate,” Journal of the American Chemical Society, vol. 133, no. 29, pp. 11163–11174, 2011. View at Publisher · View at Google Scholar · View at Scopus
  137. S. Datta, B. Holmes, J. I. Park et al., “Ionic liquid tolerant hyperthermophilic cellulases for biomass pretreatment and hydrolysis,” Green Chemistry, vol. 12, no. 2, pp. 338–345, 2010. View at Publisher · View at Google Scholar · View at Scopus
  138. M. Wada, M. Ike, and K. Tokuyasu, “Enzymatic hydrolysis of cellulose I is greatly accelerated via its conversion to the cellulose II hydrate form,” Polymer Degradation and Stability, vol. 95, no. 4, pp. 543–548, 2010. View at Publisher · View at Google Scholar · View at Scopus
  139. E. S. Gardiner and A. Sarko, “Packing analysis of carbohydrates and polysaccharides. 16. The crystal structures of celluloses IVI and IVII,” Canadian Journal of Chemistry, vol. 63, pp. 173–180, 1985.
  140. S. P. S. Chundawat, R. Vismeh, L. N. Sharma et al., “Multifaceted characterization of cell wall decomposition products formed during ammonia fiber expansion (AFEX) and dilute acid based pretreatments,” Bioresource Technology, vol. 101, no. 21, pp. 8429–8438, 2010. View at Publisher · View at Google Scholar · View at Scopus
  141. L. J. Jönsson, B. Alriksson, and N.-O. Nilvebrant, “Bioconversion of lignocellulose: inhibitors and detoxification,” Biotechnology for Biofuels, vol. 6, no. 1, article 16, 2013. View at Publisher · View at Google Scholar
  142. J. Ó. Sánchez and S. Montoya, “Production of bioethanol from biomass: an overview,” in Biofuel Technologies: Recent Developments, pp. 397–441, Springer, Berlin, Germany, 2013. View at Publisher · View at Google Scholar
  143. L. D. C. Sousa, M. Foston, A. Azarpira, J. Ralph, B. E. Dale, and V. Balan, “Fractionation and characterization of lignin from extractive ammonia pretreated corn stover,” in Proceedings of the 35th SBFC, Portland, Ore, USA, April-May 2013.
  144. E. A. Bayer, Y. Shoham, and R. Lamed, “Lignocellulose-decomposing bacteria and their enzyme systems,” in The Prokaryotes—Prokaryotic Physiology and Biochemistry, E. Rosenberg, E. F. DeLong, S. Lory, E. Stackebrandt, and F. Thompson, Eds., pp. 215–266, Springer, Berlin, Germany, 2013. View at Publisher · View at Google Scholar
  145. A. Hatakka and K. E. Hammel, “Fungal Biodegradation of Lignocelluloses,” in Industrial Applications, M. Hofrichter, Ed., vol. 10 of The Mycota, pp. 319–340, Springer, Berlin, Germany, 2nd edition, 2010. View at Publisher · View at Google Scholar
  146. Z. Zhang, A. A. Donaldson, and X. Ma, “Advancements and future directions in enzyme technology for biomass conversion,” Biotechnology Advances, vol. 30, no. 4, pp. 913–919, 2012. View at Publisher · View at Google Scholar · View at Scopus
  147. C. Somerville, S. Bauer, G. Brininstool et al., “Toward a systems approach to understanding plant cell walls,” Science, vol. 306, no. 5705, pp. 2206–2211, 2004. View at Publisher · View at Google Scholar · View at Scopus
  148. D. Gao, S. P. S. Chundawat, C. Krishnan, V. Balan, and B. E. Dale, “Mixture optimization of six core glycosyl hydrolases for maximizing saccharification of ammonia fiber expansion (AFEX) pretreated corn stover,” Bioresource Technology, vol. 101, no. 8, pp. 2770–2781, 2010. View at Publisher · View at Google Scholar · View at Scopus
  149. D. Gao, N. Uppugundla, S. P. S. Chundawat et al., “Hemicellulases and auxiliary enzymes for improved conversion of lignocellulosic biomass to monosaccharides,” Biotechnology for Biofuels, vol. 4, article 5, 2011. View at Publisher · View at Google Scholar · View at Scopus
  150. G. Banerjee, S. Car, J. S. Scott-Craig, M. S. Borrusch, M. Bongers, and J. D. Walton, “Synthetic multi-component enzyme mixtures for deconstruction of lignocellulosic biomass,” Bioresource Technology, vol. 101, no. 23, pp. 9097–9105, 2010. View at Publisher · View at Google Scholar · View at Scopus
  151. J. S. van Dyk and B. I. Pletschke, “A review of lignocellulose bioconversion using enzymatic hydrolysis and synergistic cooperation between enzymes—factors affecting enzymes, conversion and synergy,” Biotechnology Advances, vol. 30, no. 6, pp. 1458–1480, 2012. View at Publisher · View at Google Scholar · View at Scopus
  152. V. Balan, S. P. S. Chundawat, L. D. C. Sousa, and B. E. Dale, “Process for producing sugars and ethanol using corn stillage,” US 8, 367, 378 B2, 2013.
  153. S. Acharya and A. Chaudhary, “Bioprospecting thermophiles for cellulase production: a review,” Brazilian Journal of Microbiology, vol. 43, no. 3, pp. 844–856, 2012. View at Publisher · View at Google Scholar
  154. J. Liszka, M. E. Clark, E. Schneider, and D. S. Clark, “Nature versus nurture: developing enzymes that function under extreme conditions,” Annual Review of Chemical and Biomolecular Engineering, vol. 3, pp. 77–102, 2012. View at Publisher · View at Google Scholar
  155. E. Ximenesa, Y. Kima, N. Mosiera, B. Diend, and M. Ladischa, “Inhibition of cellulases by phenols,” Enzyme and Microbial Technology, vol. 46, no. 3-4, pp. 170–176, 2010. View at Publisher · View at Google Scholar
  156. P. Alvira, M. Ballesteros, and M. J. Negro, “Progress on enzymatic saccharification technologies for biofuels production,” in Biofuel Technologies: Recent Developments, V. K. Gupta and M. G. Tuohy, Eds., pp. 145–169, Springer, Berlin, Germany, 2013. View at Publisher · View at Google Scholar
  157. Y. Hong, A. S. Nizami, M. P. Bafrani, and B. A. Saville, “Impact of cellulase production on environmental and fi nancial metrics for lignocellulosic ethanol,” Biofuels, Bioproducts and Biorefining, vol. 7, no. 3, pp. 303–313, 2013. View at Publisher · View at Google Scholar
  158. M. Rizk, G. Antranikian, and S. Elleuche, “End-to-end gene fusions and their impact on the production of multifunctional biomass degrading enzymes,” Biochemical and Biophysical Research Communications, vol. 428, no. 1, pp. 1–5, 2012. View at Publisher · View at Google Scholar
  159. S. J. Horn, G. Vaaje-Kolstad, B. Westereng, and V. G. H. Eijsink, “Novel enzymes for the degradation of cellulose,” Biotechnology for Biofuels, vol. 5, no. 1, article 45, 2012. View at Publisher · View at Google Scholar
  160. M. Dashtban, H. Schraft, and W. Qin, “Fungal bioconversion of lignocellulosic residues; opportunities & perspectives,” International Journal of Biological Sciences, vol. 5, no. 6, pp. 578–595, 2009. View at Scopus
  161. L. Song, B. Siguier, C. Dumon, S. Bozonnet, and M. J. O'Donohue, “Engineering better biomass-degrading ability into a GH11 xylanase using a directed evolution strategy,” Biotechnology for Biofuels, vol. 5, no. 1, article 3, 2012. View at Publisher · View at Google Scholar · View at Scopus
  162. E. Egelkrout, V. Rajan, and J. A. Howard, “Overproduction of recombinant proteins in plants,” Plant Science, vol. 184, pp. 83–101, 2012. View at Publisher · View at Google Scholar · View at Scopus
  163. A. Culbertson, M. Jin, L. Sousa, B. E. Dale, and V. Balan, “In-house cellulases production from AFEX pretreated corn stover using Trichoderma reesei RUT C-30,” RSC Advances, vol. 3, no. 48, pp. 25960–24969, 2013. View at Publisher · View at Google Scholar
  164. Y. Zeng, S. Zhao, S. Yang, and S.-Y. Ding, “Lignin plays a negative role in the biochemical process for producing lignocellulosic biofuels,” Current Opinion in Biotechnology, vol. 27, pp. 38–45, 2014. View at Publisher · View at Google Scholar
  165. T. Jeoh, C. I. Ishizawa, M. F. Davis, M. E. Himmel, W. S. Adney, and D. K. Johnson, “Cellulase digestibility of pretreated biomass is limited by cellulose accessibility,” Biotechnology and Bioengineering, vol. 98, no. 1, pp. 112–122, 2007. View at Publisher · View at Google Scholar · View at Scopus
  166. M. Hall, P. Bansal, J. H. Lee, M. J. Realff, and A. S. Bommarius, “Cellulose crystallinity—a key predictor of the enzymatic hydrolysis rate,” FEBS Journal, vol. 277, no. 6, pp. 1571–1582, 2010. View at Publisher · View at Google Scholar · View at Scopus
  167. Z. Yu, H. Jameel, H.-M. Chang, and S. Park, “The effect of delignification of forest biomass on enzymatic hydrolysis,” Bioresource Technology, vol. 102, no. 19, pp. 9083–9089, 2011. View at Publisher · View at Google Scholar · View at Scopus
  168. X. Ju, M. Engelhard, and X. Zhang, “An advanced understanding of the specific effects of xylan and surface lignin contents on enzymatic hydrolysis of lignocellulosic biomass,” Bioresource Technology, vol. 132, pp. 137–145, 2013. View at Publisher · View at Google Scholar
  169. M. Jin, C. Gunawan, N. Uppugundla, V. Balan, and B. E. Dale, “A novel integrated biological process for cellulosic ethanol production featuring high ethanol productivity, enzyme recycling and yeast cells reuse,” Energy and Environmental Science, vol. 5, no. 5, pp. 7168–7175, 2012. View at Publisher · View at Google Scholar · View at Scopus
  170. N. Weiss, J. Börjesson, L. S. Pedersen, and A. S. Meyer, “Enzymatic lignocellulose hydrolysis: improved cellulase productivity by insoluble solids recycling,” Biotechnology for Biofuels, vol. 6, no. 1, article 5, 2013. View at Publisher · View at Google Scholar
  171. D. Gao, S. P. S. Chundawat, N. Uppugundla, V. Balan, and B. E. Dale, “Binding characteristics of Trichoderma reesei cellulases on untreated, ammonia fiber expansion (AFEX), and dilute-acid pretreated lignocellulosic biomass,” Biotechnology and Bioengineering, vol. 108, no. 8, pp. 1788–1800, 2011. View at Publisher · View at Google Scholar · View at Scopus
  172. S. A. Ansari and Q. Husain, “Potential applications of enzymes immobilized on/in nano materials: a review,” Biotechnology Advances, vol. 30, no. 3, pp. 512–523, 2012. View at Publisher · View at Google Scholar · View at Scopus
  173. K. J. Mackenzie and M. B. Francis, “Recyclable thermoresponsive polymer-cellulase bioconjugates for biomass depolymerization,” Journal of the American Chemical Society, vol. 135, no. 1, pp. 293–300, 2013. View at Publisher · View at Google Scholar
  174. J. C. Wu, K. R. Ng, J. Chong et al., “Recovery of cellulases by adsorption/desorption using cation exchange resins,” Korean Journal of Chemical Engineering, vol. 27, no. 2, pp. 469–473, 2010. View at Publisher · View at Google Scholar · View at Scopus
  175. B. Qi, X. Chen, Y. Su, and Y. Wan, “Enzyme adsorption and recycling during hydrolysis of wheat straw lignocellulose,” Bioresource Technology, vol. 102, no. 3, pp. 2881–2889, 2011. View at Publisher · View at Google Scholar · View at Scopus
  176. C. E. Wyman, B. E. Dale, R. T. Elander, M. Holtzapple, M. R. Ladisch, and Y. Y. Lee, “Comparative sugar recovery data from laboratory scale application of leading pretreatment technologies to corn stover,” Bioresource Technology, vol. 96, no. 18, pp. 2026–2032, 2005. View at Publisher · View at Google Scholar · View at Scopus
  177. C. E. Wyman, B. E. Dale, R. T. Elander et al., “Comparative sugar recovery and fermentation data following pretreatment of poplar wood by leading technologies,” Biotechnology Progress, vol. 25, no. 2, pp. 333–339, 2009. View at Publisher · View at Google Scholar · View at Scopus
  178. C. E. Wyman, V. Balan, B. E. Dale et al., “Comparative data on effects of leading pretreatments and enzyme loadings and formulations on sugar yields from different switchgrass sources,” Bioresource Technology, vol. 102, no. 24, pp. 11052–11062, 2011. View at Publisher · View at Google Scholar · View at Scopus
  179. C. E. Wyman, B. E. Dale, V. Balan et al., “Comparative performance of leading pretreatment technologies for biological conversion of corn stover, poplar wood and switchgrass to sugars,” in Aqueous Pretreatment of Plant Biomass for Biological and Chemical Conversion to Fuels and Chemicals, C. E. Wyman, Ed., Wiley Series in Renewable Resources, chapter 12, pp. 229–260, John Wiley & Sons, New York, NY, USA, 2013.
  180. Y. Lu, Y. Wang, G. Xu, J. Chu, Y. Zhuang, and S. Zhang, “Influence of high solid concentration on enzymatic hydrolysis and fermentation of steam-exploded corn stover biomass,” Applied Biochemistry and Biotechnology, vol. 160, no. 2, pp. 360–369, 2010. View at Publisher · View at Google Scholar · View at Scopus
  181. D. Humbird, A. Mohagheghi, N. Dowe, and D. J. Schell, “Economic impact of total solids loading on enzymatic hydrolysis of dilute acid pretreated corn stover,” Biotechnology Progress, vol. 26, no. 5, pp. 1245–1251, 2010. View at Scopus
  182. J. B. Kristensen, C. Felby, and H. Jørgensen, “Yield-determining factors in high-solids enzymatic hydrolysis of lignocellulose,” Biotechnology for Biofuels, vol. 2, no. 1, article 11, 2009. View at Publisher · View at Google Scholar · View at Scopus
  183. X. Zhao, L. Dong, L. Chenb, and D. Liu, “Batch and multi-step fed-batch enzymatic saccharification of formiline-pretreated sugarcane bagasse at high solid loadings for high sugar and ethanol titers,” Bioresource Technology, vol. 135, pp. 350–356, 2013. View at Publisher · View at Google Scholar
  184. B. Palmqvist, M. Wiman, and G. Lidén, “Effect of mixing on enzymatic hydrolysis of steam-pretreated spruce: a quantitative analysis of conversion and power consumption,” Biotechnology for Biofuels, vol. 4, article 10, 2011. View at Publisher · View at Google Scholar · View at Scopus
  185. H. W. Blanch, B. A. Simmons, and D. Klein-Marcuschamer, “Biomass deconstruction to sugars,” Biotechnology Journal, vol. 6, no. 9, pp. 1086–1102, 2011. View at Publisher · View at Google Scholar · View at Scopus
  186. A. O. Converse, H. Ooshima, and D. S. Burns, “Kinetics of enzymatic hydrolysis of lignocellulosic materials based on surface area of cellulose accessible to enzyme and enzyme adsorption on lignin and cellulose,” Applied Biochemistry and Biotechnology, vol. 24-25, pp. 67–73, 1990. View at Scopus
  187. S. Viamajala, J. D. McMillan, D. J. Schell, and R. T. Elander, “Rheology of corn stover slurries at high solids concentrations—effects of saccharification and particle size,” Bioresource Technology, vol. 100, no. 2, pp. 925–934, 2009. View at Publisher · View at Google Scholar · View at Scopus
  188. J. J. Stickel, J. S. Knutsen, M. W. Liberatore et al., “Rheology measurements of a biomass slurry: an inter-laboratory study,” Rheologica Acta, vol. 48, no. 9, pp. 1005–1015, 2009. View at Publisher · View at Google Scholar · View at Scopus
  189. S. Harun, V. Balan, M. S. Takriff, O. Hassan, J. Jahim, and B. E. Dale, “Performance of AFEXTM pretreated rice straw as source of fermentable sugars: the influence of particle size,” Biotechnology for Biofuels, vol. 6, no. 1, article 40, 2013.
  190. M. J. Bowman, B. S. Dien, R. E. Hector, G. Sarath, and M. A. Cotta, “Liquid chromatography-mass spectrometry investigation of enzyme-resistant xylooligosaccharide structures of switchgrass associated with ammonia pretreatment, enzymatic saccharification, and fermentation,” Bioresource Technology, vol. 110, pp. 437–447, 2012. View at Publisher · View at Google Scholar · View at Scopus
  191. L. Coulier, Y. Zha, R. Bas, and P. J. Punt, “Analysis of oligosaccharides in lignocellulosic biomass hydrolysates by high performance anion-exchange chromatography coupled with mass spectrometry (HPAEC-MS),” Bioresource Technology, vol. 133, pp. 221–231, 2013. View at Publisher · View at Google Scholar
  192. H. Li, C. Long, J. Zhou, J. Liu, X. Wu, and M. Long, “Rapid analysis of mono-saccharides and oligo-saccharides in hydrolysates of lignocellulosic biomass by HPLC,” Biotechnology Letters, vol. 35, no. 9, pp. 1405–1409, 2013. View at Publisher · View at Google Scholar
  193. Q. Qing, B. Yang, and C. E. Wyman, “Xylooligomers are strong inhibitors of cellulose hydrolysis by enzymes,” Bioresource Technology, vol. 101, no. 24, pp. 9624–9630, 2010. View at Publisher · View at Google Scholar · View at Scopus
  194. L. R. Lynd, “Overview and evaluation of fuel ethanol from cellulosic biomass: technology, economics, the environment, and policy,” Annual Review of Energy and the Environment, vol. 21, no. 1, pp. 403–465, 1996. View at Scopus
  195. B. M. Ennis, C. T. Marshall, I. S. Maddox, and A. H. J. Paterson, “Continuous product recovery by in-situ gas stripping/condensation during solvent production from whey permeate using Clostridium acetobutylicum,” Biotechnology Letters, vol. 8, no. 10, pp. 725–730, 1986. View at Publisher · View at Google Scholar · View at Scopus
  196. A. Mohagheghi, K. Evans, Y. C. Chou, and M. Zhang, “Cofermentation of glucose, xylose, and arabinose by genomic DNA-integrated xylose/arabinose fermenting strain of Zymomonas mobilis AX101,” Applied Biochemistry and Biotechnology A: Enzyme Engineering and Biotechnology, vol. 98–100, pp. 885–898, 2002. View at Publisher · View at Google Scholar · View at Scopus
  197. K. C. Zhang, M. R. Sawaya, D. S. Eisenberg, and J. C. Liao, “Expanding metabolism for biosynthesis of nonnatural alcohols,” Proceedings of the National Academy of Sciences of the United States of America, vol. 105, no. 52, pp. 20653–20658, 2008. View at Publisher · View at Google Scholar · View at Scopus
  198. H. B. Xie, H. W. Shen, Z. W. Gong, Q. Wang, Z. B. K. Zhao, and F. W. Bai, “Enzymatic hydrolysates of corn stover pretreated by a N-methylpyrrolidone-ionic liquid solution for microbial lipid production,” Green Chemistry, vol. 14, no. 4, pp. 1202–1210, 2012. View at Publisher · View at Google Scholar · View at Scopus
  199. X. C. Yu, Y. B. Zheng, K. M. Dorgan, and S. L. Chen, “Oil production by oleaginous yeasts using the hydrolysate from pretreatment of wheat straw with dilute sulfuric acid,” Bioresource Technology, vol. 102, no. 10, pp. 6134–6140, 2011. View at Publisher · View at Google Scholar · View at Scopus
  200. S. Papanikolaou and G. Aggelis, “Lipids of oleaginous yeasts—part I: biochemistry of single cell oil production,” European Journal of Lipid Science and Technology, vol. 113, no. 8, pp. 1031–1051, 2011. View at Publisher · View at Google Scholar · View at Scopus
  201. Z. Ruan, M. Zanotti, X. Wang, C. Ducey, and Y. Liu, “Evaluation of lipid accumulation from lignocellulosic sugars by Mortierella isabellina for biodiesel production,” Bioresource Technology, vol. 110, pp. 198–205, 2012. View at Publisher · View at Google Scholar · View at Scopus
  202. A. Vlysidis, M. Binns, C. Webb, and C. Theodoropoulos, “A techno-economic analysis of biodiesel biorefineries: assessment of integrated designs for the co-production of fuels and chemicals,” Energy, vol. 36, no. 8, pp. 4671–4683, 2011. View at Publisher · View at Google Scholar · View at Scopus
  203. C. Ratledge and J. P. Wynn, “The biochemistry and molecular biology of lipid accumulation in oleaginous microorganisms,” Advances in Applied Microbiology, vol. 51, pp. 1–51, 2002. View at Publisher · View at Google Scholar · View at Scopus
  204. D. J. Wohlbach, A. Kuo, T. K. Sato et al., “Comparative genomics of xylose-fermenting fungi for enhanced biofuel production,” Proceedings of the National Academy of Sciences of the United States of America, vol. 108, no. 32, pp. 13212–13217, 2011. View at Publisher · View at Google Scholar · View at Scopus
  205. S. Ha, J. M. Galazka, S. R. Kim et al., “Engineered Saccharomyces cerevisiae capable of simultaneous cellobiose and xylose fermentation,” Proceedings of the National Academy of Sciences of the United States of America, vol. 108, no. 2, pp. 504–509, 2011. View at Publisher · View at Google Scholar · View at Scopus
  206. M. Kuyper, A. A. Winkler, J. P. Van Dijken, and J. T. Pronk, “Minimal metabolic engineering of Saccharomyces cerevisiae for efficient anaerobic xylose fermentation: a proof of principle,” FEMS Yeast Research, vol. 4, no. 6, pp. 655–664, 2004. View at Publisher · View at Google Scholar · View at Scopus
  207. M. Sonderegger, M. Schümperli, and U. Sauer, “Metabolic engineering of a phosphoketolase pathway for pentose catabolism in Saccharomyces cerevisiae,” Applied and Environmental Microbiology, vol. 70, no. 5, pp. 2892–2897, 2004. View at Publisher · View at Google Scholar · View at Scopus
  208. A. Asghari, R. J. Bothast, J. B. Doran, and L. O. Ingram, “Ethanol production from hemicellulose hydrolysates of agricultural residues using genetically engineered Escherichia coli strain KO11,” Journal of Industrial Microbiology, vol. 16, no. 1, pp. 42–47, 1996. View at Scopus
  209. M. Jin, V. Balan, C. Gunawan, and B. E. Dale, “Quantitatively understanding reduced xylose fermentation performance in AFEXTM treated corn stover hydrolysate using Saccharomyces cerevisiae 424A (LNH-ST) and Escherichia coli KO11,” Bioresource Technology, vol. 111, pp. 294–300, 2012. View at Publisher · View at Google Scholar · View at Scopus
  210. C. Zhong, M. W. Lau, V. Balan, B. E. Dale, and Y.-J. Yuan, “Optimization of enzymatic hydrolysis and ethanol fermentation from AFEX-treated rice straw,” Applied Microbiology and Biotechnology, vol. 84, no. 4, pp. 667–676, 2009. View at Publisher · View at Google Scholar · View at Scopus
  211. A. Kollaras, P. J. L. Bell, and P. V. Attfield, “A feed and fuel approach to making second generation bioethanol techno-economically viable,” in Proceedings of the ISAF 19th International Symposium on Alcohol Fuels, Verona, Italy, October 2011.
  212. T. K. Ng, A. Ben-Bassat, and J. G. Zeikus, “Ethanol production by thermophilic bacteria: fermentation of cellulosic substrates by cocultures of Clostridium thermocellum and Clostridium thermohydrosulfuricum,” Applied and Environmental Microbiology, vol. 41, no. 6, pp. 1337–1343, 1981. View at Scopus
  213. L. R. Lynd, P. J. Weimer, W. H. van Zyl, and I. S. Pretorius, “Microbial cellulose utilization: fundamentals and biotechnology,” Microbiology and Molecular Biology Reviews, vol. 66, no. 3, pp. 506–577, 2002. View at Publisher · View at Google Scholar · View at Scopus
  214. S. D. Brown, A. M. Guss, T. V. Karpinets et al., “Mutant alcohol dehydrogenase leads to improved ethanol tolerance in Clostridium thermocellum,” Proceedings of the National Academy of Sciences of the United States of America, vol. 108, no. 33, pp. 13752–13757, 2011. View at Publisher · View at Google Scholar · View at Scopus
  215. T. A. Warnick, B. A. Methé, and S. B. Leschine, “Clostridium phytofermentans sp. nov., a cellulolytic mesophile from forest soil,” International Journal of Systematic and Evolutionary Microbiology, vol. 52, no. 4, pp. 1155–1160, 2002. View at Publisher · View at Google Scholar · View at Scopus
  216. M. Jin, C. Gunawan, V. Balan, and B. E. Dale, “Consolidated bioprocessing (CBP) of AFEX-pretreated corn stover for ethanol production using Clostridium phytofermentans at a high solids loading,” Biotechnology and Bioengineering, vol. 109, no. 8, pp. 1929–1936, 2012. View at Publisher · View at Google Scholar · View at Scopus
  217. R. den Haan, H. Kroukamp, M. Mert, M. Bloom, J. F. Gorgens, and W. H. van Zyl, “Engineering Saccharomyces cerevisiae for next generation ethanol production,” Journal of Chemical Technology and bioTechnology, vol. 88, no. 6, pp. 983–991, 2013. View at Publisher · View at Google Scholar
  218. R. den Haan, H. Kroukamp, J. H. D. van Zyl, and W. H. van Zyl, “Cellobiohydrolase secretion by yeast: current state and prospects for improvement,” Process Biochemistry, vol. 48, no. 1, pp. 1–12, 2013. View at Publisher · View at Google Scholar
  219. D. C. La Grange, R. den Haan, and W. H. van Zyl, “Engineering cellulolytic ability into bioprocessing organisms,” Applied Microbiology and Biotechnology, vol. 87, no. 4, pp. 1195–1208, 2010. View at Publisher · View at Google Scholar · View at Scopus
  220. I. Kamei, Y. Hirota, T. Mori, H. Hirai, S. Meguro, and R. Kondo, “Direct ethanol production from cellulosic materials by the hypersaline-tolerant white-rot fungus Phlebia sp. MG-60,” Bioresource Technology, vol. 112, pp. 137–142, 2012. View at Publisher · View at Google Scholar · View at Scopus
  221. M. W. Lau and B. E. Dale, “Cellulosic ethanol production from AFEX-treated corn stover using Saccharomyces cerevisiae 424A(LNH-ST),” Proceedings of the National Academy of Sciences of the United States of America, vol. 106, no. 5, pp. 1368–1373, 2009. View at Publisher · View at Google Scholar · View at Scopus
  222. E. Casey, M. Sedlak, N. W. Y. Ho, and N. S. Mosier, “Effect of acetic acid and pH on the cofermentation of glucose and xylose to ethanol by a genetically engineered strain of Saccharomyces cerevisiae,” FEMS Yeast Research, vol. 10, no. 4, pp. 385–393, 2010. View at Publisher · View at Google Scholar · View at Scopus
  223. B. Erdei, B. Franko, M. Galbe, and G. Zacchi, “Glucose and xylose co-fermentation of pretreated wheat straw using mutants of S. cerevisiae TMB3400,” Journal of Biotechnology, vol. 164, no. 1, pp. 50–58, 2013. View at Publisher · View at Google Scholar
  224. M. J. Jin, C. Sarks, C. Gunawan et al., “Phenotypic selection of a wild Saccharomyces cerevisiae strain for simultaneous saccharification and co-fermentation of AFEX pretreated corn stover,” Biotechnology for Biofuels, vol. 6, no. 1, article 108, 2013. View at Publisher · View at Google Scholar
  225. M. Kuyper, M. J. Toirkens, J. A. Diderich, A. A. Winkler, J. P. van Dijken, and J. T. Pronk, “Evolutionary engineering of mixed-sugar utilization by a xylose-fermenting Saccharomyces cerevisiae strain,” FEMS Yeast Research, vol. 5, no. 10, pp. 925–934, 2005. View at Publisher · View at Google Scholar · View at Scopus
  226. U. Gunawardena, P. Meinhold, M. W. Peters, J. Urano, and R. M. R. Feldman, “Butanol production by metabolically engineered yeast,” US Patent US, 2010/0062505 A1, 2010.
  227. X. Chen, K. F. Nielsen, I. Borodina, M. C. Kielland-Brandt, and K. Karhumaa, “Increased isobutanol production in Saccharomyces cerevisiae by overexpression of genes in valine metabolism,” Biotechnology for Biofuels, vol. 4, article 21, 2011. View at Publisher · View at Google Scholar · View at Scopus
  228. J. Urano, C. A. Dundon, P. Meinhold et al., “Cytosolic isobutanol pathway localization for the production of isobutanol,” US Patent, 2011/0076733 A1, 2011.
  229. L. C. Anthony, L. L. Huang, and R. W. Ye, “Production of isobutanol in yeast mitochondria,” US Patent, 2010/0129886 A1, 2010.
  230. G. K. Donaldson, A. C. Eliot, D. Flint, L. A. Maggio-Hall, and V. Nagarajan, “Fermentive production of four carbon alcohols,” US Patent, 7993889 B1, 2011.
  231. E. Zikou, A. Chatzifragkou, A. A. Koutinas, and S. Papanikolaou, “Evaluating glucose and xylose as cosubstrates for lipid accumulation and γ-linolenic acid biosynthesis of Thamnidium elegans,” Journal of Applied Microbiology, vol. 114, no. 4, pp. 1020–1032, 2013. View at Publisher · View at Google Scholar
  232. J. A. Ubersax and D. M. Platt, “Genetically modified microbes producing isoprenoids,” WO Patent, 2010/141452 A1, 2010.
  233. B. S. Dien, M. A. Cotta, and T. W. Jeffries, “Bacteria engineered for fuel ethanol production: current status,” Applied Microbiology and Biotechnology, vol. 63, no. 3, pp. 258–266, 2003. View at Publisher · View at Google Scholar · View at Scopus
  234. J. D. Keasling, “Manufacturing molecules through metabolic engineering,” Science, vol. 330, no. 6009, pp. 1355–1358, 2010. View at Publisher · View at Google Scholar · View at Scopus
  235. S. U. Lee, K. Jung, G. W. Park et al., “Bioprocessing aspects of fuels and chemicals from biomass,” Korean Journal of Chemical Engineering, vol. 29, no. 7, pp. 831–850, 2012. View at Publisher · View at Google Scholar
  236. L. M. Vane, “A review of pervaporation for product recovery from biomass fermentation processes,” Journal of Chemical Technology and Biotechnology, vol. 80, no. 6, pp. 603–629, 2005. View at Publisher · View at Google Scholar · View at Scopus
  237. S. S. Gaykawad, Y. Zha, P. J. Punt, J. W. van Groenestijn, L. A. M. van der Wielen, and A. J. J. Straathof, “Pervaporation of ethanol from lignocellulosic fermentation broth,” Bioresource Technology, vol. 129, pp. 469–476, 2013. View at Publisher · View at Google Scholar
  238. N. Qureshi and H. P. Blaschek, “Recovery of butanol from fermentation broth by gas stripping,” Renewable Energy, vol. 22, no. 4, pp. 557–564, 2000. View at Publisher · View at Google Scholar · View at Scopus
  239. T. de Vrije, M. Budde, H. van der Wal, P. A. M. Claassen, and A. M. Lopez-Contreras, “‘In situ’ removal of isopropanol, butanol and ethanol from fermentation broth by gas stripping,” Bioresource Technology, vol. 137, pp. 153–159, 2013. View at Publisher · View at Google Scholar
  240. C. Chen, X. Tang, Z. Xiao, Y. Zhou, Y. Jiang, and S. Fu, “Ethanol fermentation kinetics in a continuous and closed-circulating fermentation system with a pervaporation membrane bioreactor,” Bioresource Technology, vol. 114, pp. 707–710, 2012. View at Publisher · View at Google Scholar · View at Scopus
  241. W. G. Hettinga, H. M. Junginger, S. C. Dekker, M. Hoogwijk, A. J. McAloon, and K. B. Hicks, “Understanding the reductions in US corn ethanol production costs: an experience curve approach,” Energy Policy, vol. 37, no. 1, pp. 190–203, 2009. View at Publisher · View at Google Scholar · View at Scopus
  242. J. D. Stephen, W. E. Mabee, and J. N. Saddler, “Will second-generation ethanol be able to compete with first-generation ethanol? Opportunities for cost reduction,” Biofuels, Bioproducts and Biorefining, vol. 6, no. 2, pp. 159–176, 2012. View at Publisher · View at Google Scholar · View at Scopus
  243. C. O. Tuck, E. Pérez, I. T. Horváth, R. A. Sheldon, and M. Poliakoff, “Valorization of biomass: deriving more value from waste,” Science, vol. 337, no. 6095, pp. 695–699, 2012. View at Publisher · View at Google Scholar
  244. H. Bjørsvik and F. Minisci, “Fine chemicals from lignosulfonates. 1. Synthesis of vanillin by oxidation of lignosulfonates,” Organic Process Research and Development, vol. 3, no. 5, pp. 330–340, 1999. View at Scopus
  245. R. A. Sheldon and H. van Bekkum, Fine Chemicals through Heterogeneous Catalysis, Wiley-VCH, Weinheim, Germany, 2001.
  246. J. Zakzeski, P. C. A. Bruijnincx, A. L. Jongerius, and B. M. Weckhuysen, “The catalytic valorization of lignin for the production of renewable chemicals,” Chemical Reviews, vol. 110, no. 6, pp. 3552–3599, 2010. View at Publisher · View at Google Scholar · View at Scopus
  247. M. P. Pandey and C. S. Kim, “Lignin depolymerization and conversion: a review of thermochemical methods,” Chemical Engineering and Technology, vol. 34, no. 1, pp. 29–41, 2011. View at Publisher · View at Google Scholar · View at Scopus
  248. A. G. Sergeev and J. F. Hartwig, “Selective, nickel-catalyzed hydrogenolysis of aryl ethers,” Science, vol. 332, no. 6028, pp. 439–443, 2011. View at Publisher · View at Google Scholar · View at Scopus
  249. T. D. Matson, K. Barta, A. V. Iretskii, and P. C. Ford, “One-pot catalytic conversion of cellulose and of woody biomass solids to liquid fuels,” Journal of the American Chemical Society, vol. 133, no. 35, pp. 14090–14097, 2011. View at Publisher · View at Google Scholar · View at Scopus
  250. A. G. Gayubo, B. Valle, A. T. Aguayo, M. Olazar, and J. Bilbao, “Pyrolytic lignin removal for the valorization of biomass pyrolysis crude bio-oil by catalytic transformation,” Journal of Chemical Technology and Biotechnology, vol. 85, no. 1, pp. 132–144, 2010. View at Publisher · View at Google Scholar · View at Scopus
  251. P. Gallezot, “Conversion of biomass to selected chemical products,” Chemical Society Reviews, vol. 41, no. 4, pp. 1538–1558, 2012. View at Publisher · View at Google Scholar · View at Scopus
  252. D. Turner, “Lignol energy,” in Proceedings of the World Congress on Industrial, Biotechnology and Bioprocessing, Chicago, Ill, USA, 2008.
  253. X. Pan and J. N. Saddler, “Effect of replacing polyol by organosolv and kraft lignin on the property and structure of rigid polyurethane foam,” Biotechnology for Biofuels, vol. 6, no. 1, article 12, 2013. View at Publisher · View at Google Scholar
  254. S. L. L. L Averous, “Chemical modification of lignins towards bio-based polymers,” Progress in Polymer Science, 2013. View at Publisher · View at Google Scholar
  255. B. Bals, L. Teachworth, B. Dale, and V. Balan, “Extraction of proteins from switchgrass using aqueous ammonia within an integrated biorefinery,” Applied Biochemistry and Biotechnology, vol. 143, no. 2, pp. 187–198, 2007. View at Publisher · View at Google Scholar · View at Scopus
  256. B. Bals, B. E. Dale, and V. Balan, “Recovery of leaf protein for animal feed and high value uses,” in Biorefinery Co-Products: Phytochemicals, Primary Metabolites and Value-Added Biomass Processing, V. Bergerson, D. J. Carrier, and S. Ramasamy, Eds., Wiley Publication, chapter 9, pp. 179–198, John Wiley & Sons, New York, NY, USA, 2012.
  257. J. Sanders, E. Scott, R. Weusthuis, and H. Mooibroek, “Bio-refinery as the bio-inspired process to bulk chemicals,” Macromolecular Bioscience, vol. 7, no. 2, pp. 105–117, 2007. View at Publisher · View at Google Scholar · View at Scopus
  258. P. M. Könst, P. M. C. C. D. Turras, M. C. R. Franssen, E. L. Scott, and J. P. M. Sanders, “Stabilized and immobilized bacillus subtilis arginase for the biobased production of nitrogen-containing chemicals,” Advanced Synthesis and Catalysis, vol. 352, no. 9, pp. 1493–1502, 2010. View at Publisher · View at Google Scholar · View at Scopus
  259. M. W. Lau, B. D. Bals, S. P. S. Chundawat et al., “An integrated paradigm for cellulosic biorefineries: utilization of lignocellulosic biomass as self-sufficient feedstocks for fuel, food precursors and saccharolytic enzyme production,” Energy and Environmental Science, vol. 5, no. 5, pp. 7100–7110, 2012. View at Publisher · View at Google Scholar · View at Scopus
  260. F. A. Gonçalves, E. J. Sanjinez-Argandona, and G. G. Fonseca, “Cellulosic ethanol and its co-products from different substrates, pretreatments, microorganisms and bioprocesses: a review,” Natural Science, vol. 5, no. 5, pp. 624–630, 2013. View at Publisher · View at Google Scholar
  261. A. Aden, M. Ruth, K. Ibsen et al., “Lignocellulosic biomass to ethanol process design and economics utilizing co-current dilute acid prehydrolysis and enzymatic hydrolysis for corn stover,” NREL/TP-510-32438, National Renewable Energy Laboratory, Golden, Colo, USA, 2002.
  262. M. Kaylen, D. L. van Dyne, Y. Choi, and M. Blase, “Economic feasibility of producing ethanol from lignocellulosic feedstocks,” Bioresource Technology, vol. 72, no. 1, pp. 19–32, 2000. View at Publisher · View at Google Scholar · View at Scopus
  263. M. Wright and R. C. Brown, “Establishing the optimal sizes of different kinds of biorefineries,” Biofuels, Bioproducts and Biorefining, vol. 1, no. 3, pp. 191–200, 2007. View at Publisher · View at Google Scholar · View at Scopus
  264. J. Leboreiro and A. K. Hilaly, “Biomass transportation model and optimum plant size for the production of ethanol,” Bioresource Technology, vol. 102, no. 3, pp. 2712–2723, 2011. View at Publisher · View at Google Scholar · View at Scopus
  265. J. Leboreiro and A. K. Hilaly, “Analysis of supply chain, scale factor, and optimum plant capacity for the production of ethanol from corn stover,” Biomass and Bioenergy, vol. 54, pp. 158–169, 2013. View at Publisher · View at Google Scholar
  266. A. M. Argo, E. C. D. Tan, D. Inman et al., “Investigation of biochemical biorefinery sizing and environmental sustainability impacts for conventional bale system and advanced uniform biomass logistics designs,” Biofuels, Bioproducts and Biorefining, vol. 7, no. 3, pp. 282–302, 2013. View at Publisher · View at Google Scholar
  267. A. Bernardi, S. Giarola, and F. Bezzo, “Spatially explicit multiobjective optimization for the strategic design of first and second generation biorefineries including carbon and water footprints,” Industrial and Engineering Chemistry Research, vol. 52, no. 22, pp. 7170–7180, 2013. View at Publisher · View at Google Scholar
  268. G. Yuliani, A. L. Chaffee, and G. Garnier, “Biorefinery process water effluent treatments by salt coagulation,” Biomass and Bioenenergy, vol. 56, pp. 189–196, 2013. View at Publisher · View at Google Scholar
  269. S. Verenich and J. Kallas, “Coagulation as a post-treatment process for wet oxidation of pulp and paper mill circulation waters,” Chemical Engineering and Technology, vol. 24, no. 11, pp. 1183–1188, 2001. View at Publisher · View at Google Scholar
  270. M. O. S. Dias, T. L. Junqueira, C. E. V. Rossell, R. M. Filho, and A. Bonomi, “Evaluation of process configurations for second generation integrated with first generation bioethanol production from sugarcane,” Fuel Processing Technology, vol. 109, pp. 84–89, 2013. View at Publisher · View at Google Scholar
  271. A. Kendall and J. Yuan, “Comparing life cycle assessments of different biofuel options,” Current Opinion in Chemical Biology, vol. 17, no. 3, pp. 439–443, 2013. View at Publisher · View at Google Scholar
  272. A. L. Borrion, M. C. McManus, and G. P. Hammond, “Environmental life cycle assessment of lignocellulosic conversion to ethanol: a review,” Renewable and Sustainable Energy Reviews, vol. 16, no. 7, pp. 4638–4650, 2012. View at Publisher · View at Google Scholar
  273. A. Uihlein and L. Schebek, “Environmental impacts of a lignocellulose feedstock biorefinery system: an assessment,” Biomass and Bioenergy, vol. 33, no. 5, pp. 793–802, 2009. View at Publisher · View at Google Scholar · View at Scopus
  274. E. Martinez-Hernandez, G. Campbell, and J. Sadhukhan, “Economic value and environmental impact (EVEI) analysis of biorefinery systems,” Chemical Engineering Research and Design, vol. 91, no. 8, pp. 1418–1426, 2013. View at Publisher · View at Google Scholar
  275. T. L. Richard, “Challenges in scaling up biofuels infrastructure,” Science, vol. 329, no. 5993, pp. 793–796, 2010. View at Publisher · View at Google Scholar · View at Scopus
  276. H. von Blottnitz and M. A. Curran, “A review of assessments conducted on bio-ethanol as a transportation fuel from a net energy, greenhouse gas, and environmental life cycle perspective,” Journal of Cleaner Production, vol. 15, no. 7, pp. 607–619, 2007. View at Publisher · View at Google Scholar · View at Scopus
  277. Á. D. González-Delgado, Y. Peralta-Ruíz, Y. Pardo, and V. Kafarov, “Energy integration of bioethanol production process topology from microalgae biomass: evaluation of SSCF, SSF, acid hydrolysis and product purification alternatives,” Chemical Engineering Transactions, vol. 35, pp. 1069–1074, 2013.
  278. J. Y. Zhu and X. S. Zhuang, “Conceptual net energy output for biofuel production from lignocellulosic biomass through biorefining,” Progress in Energy and Combustion Science, vol. 38, no. 4, pp. 583–598, 2012. View at Publisher · View at Google Scholar · View at Scopus
  279. A. Kelloway and P. Daoutidis, “Process synthesis of biorefineries: optimization of biomass conversion to fuels and chemicals,” Industrial and Engineering Chemistry Research, 2013. View at Publisher · View at Google Scholar
  280. H. A. Ruiz, R. M. Rodrıguez-Jasso, B. D. Fernandes, A. A. Vicente, and J. A. Teixeira, “Hydro thermal processing, as an alternative for upgrading agriculture residues and marine biomass according to the biorefinery concept: a review,” Renewable and Sustainable Energy Reviews, vol. 21, pp. 35–51, 2013. View at Publisher · View at Google Scholar
  281. F. Cherubini, “The biorefinery concept: using biomass instead of oil for producing energy and chemicals,” Energy Conversion and Management, vol. 51, no. 7, pp. 1412–1421, 2010. View at Publisher · View at Google Scholar · View at Scopus
  282. S. Yılmaz and H. Selim, “A review on the methods for biomass to energy conversion systems design,” Renewable and Sustainable Energy Reviews, vol. 25, pp. 420–430, 2013. View at Publisher · View at Google Scholar
  283. J. Maclellan, R. Chen, R. Kraemer, Y. Zhong, Y. Liu, and W. Liao, “Anaerobic treatment of lignocellulosic material to co-produce methane and digested fiber for ethanol biorefining,” Bioresource Technology, vol. 130, pp. 418–423, 2013. View at Publisher · View at Google Scholar
  284. A.-S. Nizami and I. M. Ismail, “Life-cycle assessment of biomethane from lignocellulosic biomass,” in Life Cycle Assessment of Renewable Energy Sources, Green Energy and Technology, A. Singh, D. Pant, and S. I. Olsen, Eds., Green Energy and Technology, pp. 79–94, Springer, London, UK, 2013. View at Publisher · View at Google Scholar
  285. S. Ramaswamy, H.-J. Huang, and B. V. Ramarao, Separation and Purification Technologies in Biorefineries, Wiley Online Library, 2013.
  286. H. K. Sreenath, “Diminished respirative growth and enhanced assimilative sugar uptake result in higher specific fermentation rates by the mutant Pichia stipitis FPL-061,” Applied Biochemistry and Biotechnology A: Enzyme Engineering and Biotechnology, vol. 63–65, no. 1–3, pp. 109–116, 1997. View at Scopus