About this Journal Submit a Manuscript Table of Contents
ISRN Metallurgy
Volume 2013 (2013), Article ID 429818, 5 pages
http://dx.doi.org/10.1155/2013/429818
Research Article

Electrochemical Fabrication of Niobium Silicon Alloys from Oxide Powder Mixtures

School of Materials Science and Engineering, Beihang University, No.37 Xueyuan Road, Haidian District, Beijing 100191, China

Received 14 January 2013; Accepted 31 January 2013

Academic Editors: Y. S. Chang, P. Lukac, A. Pinkerton, and Y.-d. Wang

Copyright © 2013 Fanke Meng and Huimin Lu. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

NbSi alloys were prepared by direct electrochemically reducing four mixed Nb2O5 and SiO2 powders (Nb-10Si, Nb-20Si, Nb-30Si, and Nb-37.5Si) in molten CaCl2 electrolyte at 900°C. The samples were characterized with scanning electron microscope (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy (EDX). No oxidized phases were remained by XRD tests. Under SEM, Nb phase was scattered in Nb5Si3 phase for the samples of Nb-10Si, Nb-20Si, and Nb-30Si. For the sample of Nb-37.5Si, only Nb5Si3 was obtained after electrolysis.

1. Introduction

Nickel alloys are the mostly used superalloys in aviation industry. Due to the demand of exploring new generation aircraft turbine engines, scientists and engineers are devoted to investigate less expensive superalloys with higher melting points to substitute the Ni-based alloys [1, 2]. Following this idea, NbSi alloys (0.5–37.5 at % Si) are attracting more and more attention because of the high melting points of the two composed phases (melting points: Nb, 2469°C; Nb5Si3, 2520°C) in the alloy system [1]. Moreover, NbSi alloys still have three other excellent properties: close coefficient of heat expansion of the two compositions (Nb, 7.3 × 10 k−1; Nb5Si3, 6.1 × 10 k−1), relative lower density (7.16 g cm−3), and reasonable strength at high temperature. Thus, NbSi alloys are considered to be a potential candidate of the next generation superalloys. Until now, the mainly used techniques for fabricating NbSi alloys are orientation solidification [3], smelting with argon arc [4], physical vapor deposition (PVD), as well as some other methods of powder metallurgy. Generally, all of these techniques have the following procedures: first, extracting pure Nb and Si from minerals; second, melting and mixing molten Nb and Si by using arc or electron beam melting method; third, casting the mixed molten alloys to ingots. However, the notorious weakness of the process is resulted from high energy consumption and complex production procedures. As a typical example, the only commercial process for the production of metallic Nb is reducing K2NbF7 or Nb2O5 with sodium reduction or carbothermal reduction, respectively [5]. For production of silicon, the conventional technique is reducing SiO2 with carbothermal reduction technique. The typical reduction temperature is as high as 1700°C, which therefore needs intensive energy and releases carbon oxides as wasted gases in the process [6]. Also, another critical disadvantage should be paid more attention: it is difficult to homogenize Nb and Si in any melting process due to the very high melting point of metallic Nb.

During the recent decade, in order to produce high-melting-point metals and superalloys, many new skills were studied by scientists and engineers. Among them, direct electrochemical reduction of metal oxides or mixed oxides in molten electrolytes was an effective method for production of metals and alloys. The typical examples were FFC Cambridge Process and the derived methods. In this process, metal oxides were pressed to solid pellets as a cathode and the graphite were acted as an anode, which were soaked into the molten CaCl2 at about high temperatures (700–900°C) for electrolysis simultaneously. Consequently, a potential was loaded between the two electrodes. Generally, this technique was used in production of many metals and nonmetals for example, Cr, Si, Nb, Ni, and Zr [712]. The whole reaction process can be described with the following equations:

Cathode

Anode In these equations, the A is a symbol of metal or nonmetal elements. If the cathode was mixed oxides, the reduction production might be oxygen-free alloys. Therefore, this electrochemical method can be effectively used for refractory metals, high-melting-point nonmetals, and superalloys.

Herein, we used this electrochemical reduction method for the production of NbSi alloys in the molten CaCl2 at high temperature (900°C). The processors were mixed Nb2O5 and SiO2 powders of four various atomic ratios of Nb and Si. After electrolysis, the NbSi alloys were successfully obtained. After scanning electron microscope (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy (EDX) analysis, the NbSi alloys were composed of different phases and almost free of oxygen. Therefore, this electrochemical reduction method had paved a way for the NbSi alloys production, which is also able to be applied to fabricate other refractory alloys.

2. Experimental Details

2.1. Materials Preparation

In this research work, the electrolyte was CaCl2. In this work, CaCl2 (≥99.0%), Nb2O5 (>99.9%), and SiO2 (>99.8%) powders were purchased from Chengde Optical and Electrical Materials Ltd., Hebei Province, China. The pellets preparation was following the below steps. First, CaCl2 powders were dried at 80°C overnight and then pressed to small cylindrical blocks with a pressure of 30 MPa. Second, the cylindrical blocks were dried again at 80°C for several hours and then pulverized to small CaCl2 pellets with an average sized less than 1 mm. For the preparation of the Nb2O5/SiO2 pellets, the process was identical as that used for CaCl2 pellets preparation. The Nb2O5 and SiO2 powders were mixed with the atomic ratios of Nb-10Si (Nb, 90 at %; Si, 10 at %), Nb-20Si (Nb, 80 at %; Si, 20 at %), Nb-30Si (Nb, 70 at %; Si, 30 at %), and Nb-37.5Si (Nb, 62.5 at %; Si, 37.5 at %) between Nb and Si. The total mixed powder was 200 g. The graphite crucibles (inner diameter: ~9.0 cm, height: ~18.0 cm, wall thickness: ~1.0 cm) were cleaned with ethanol (>95%, Beijing Keshi Co. Ltd. Beijing, China) for at least 5 times until the inner walls of the graphite crucible were almost free of graphite powders. At last, the mixed Nb2O5/SiO2 pellets were placed in the cleaned crucible and then the CaCl2 pellets (~2000 g) were placed on the top of the Nb2O5/SiO2 pellets.

2.2. Potentiostatic Electrolysis

The process of electrolysis was conducted in a programmable temperature-controlled furnace produced by China Iron & Steel Research Institute Group. The design of the instrument was shown in the schematic of Figure 1. The graphite crucible filled with Nb2O5/SiO2 and CaCl2 was placed in a graphite stage in the furnace. As an anode, a graphite rod (diameter: 6.0 cm) was just hanged above the crucible vertically by a mechanic instrument, which can push the graphite rod move up and down to ensure that the rod can contact with the molten electrolyte during the whole electrolysis process. The direct current for the electrolysis was supplied by a KGHF-1000A/6V rectifier, made by Beijing Chunshu Electric rectifier Ltd., Beijing, China. The temperature-controlled furnace was vacuumed and then filled with argon (≥99.9%, O2 ≤ 10 ppm, H2O ≤ 15 ppm, N2 ≤ 5 ppm) as soon as possible. It should be noted that the argon flow was maintained with a rate of 1.0–1.5 L min−1 and the outlet was adjusted with a valve to ensure that the gas pressure inside the furnace was about 0.01 MPa larger than the ambient pressure, which was helpful for avoiding air to ingress into the furnace in the electrolysis process. The heating process was of three steps: first, the temperature was heated to 780°C with a ramping rate of 10°C min−1; second, kept at 780°C for 30 min, the CaCl2 electrolyte was completely melted in the crucible; third, the temperature continued to rise up to 900°C with a heating rate of 10°C min−1. Consequently, the potential was loaded and then stabilized at 3.0 V for electrolysis between the two electrodes. The electrolysis would be lasted for about 4-5 hours, and the graphite crucible with the products was removed out the furnace as the temperature in the furnace was decreased to room temperature after electrolysis. The product was obtained by smashing the crucible.

429818.fig.001
Figure 1: Schematic of eletrolysis system.
2.3. Characterizations of Morphology and Composition

Micrograph and composition analyses were conducted with a SEM system equipped with a CCD camera, from TESCAN. EDX equipment was purchased from OXFORD and analysis software was INCA. The phase composition of the NbSi alloys was identified by a Rigaku D/Max 2200 PC X-ray diffractometer.

3. Results and Discussion

After electrolysis at 900°C in molten CaCl2, the samples were obtained. Figure 2 showed the pictures of the obtained product after electrolysis. As shown in Figure 2(a), the CaCl2 electrolyte and the sample were molten together after electrolysis. By smashing the crucible, a block of ingot was obtained in Figure 2(b). Clearly, the ingot had two layers of different materials. A metal-like layer with a color of grayish was rich of alloys and other layer was mainly composed of electrolyte.

fig2
Figure 2: (a) top view of the crucible after electrolysis; (b) the sample with electrolyte after electrolysis.

It should be noted that Figure 2 only showed typical pictures after electrolysis of the processor powder for the alloy of Nb-37.5Si. The other three samples were also of a similar picture, which were not shown here. The morphologies of the alloys were shown in the SEM images in Figure 3. The white small particles with an average size about 10–20 nm had Nb concentration of 98.2 at % in Table 1. On the contrary, the concentrations of the Si and the O were only 1.6 at % and 0.2 at %, respectively. Therefore, it was clearly to show that the white small particles were mainly composed of Nb. In the grey areas, the concentrations of NB and Si were 89.4 and 10.1 at % respectively, which was almost equated to the ratio of Nb-10Si alloy. It should be noted that only a very small part of O was still remained in both the white small particles and the grey areas. Although the O was not completely electrochemical reduced, it can be removed by other metallurgical methods in the consequent process. Typically, the mixed Nb2O5/SiO2 powder was almost completely electrodeoxidized in molten CaCl2 at 900°C. For the processor powder mixture of Nb-20Si alloy, the product after electrolysis the SEM image was shown in Figure 3(b), which was similar to the image in Figure 3(a). The EDX results in the Table 1 also showed that the white particles were Nb and the grey areas were NbSi alloy (Nb-20Si). The similar SEM image and EDX results were shown for the sample Nb-30Si alloy. Compare the three alloys (Nb-10Si, Nb-20Si, and Nb-30Si), two conclusions were obtained. First, the grey areas in all the three images had Nb and Si concentrations close to 62.5 and 37.5 at %, respectively, which was the atomic ratio in the Nb5Si3 alloy. Second, the white small particles were almost mainly composed of metallic Nb. Third, although O was remained in a little part in all the three samples, most of the O were still removed electrochemically. For the powder mixture of Nb-37.5Si alloy, the product after electrolysis, the SEM image, and EDX result were shown in Figure 3(d) and Table 1, respectively. Clearly, the product in the SEM image showed a homogenous phase with a Nb/Si ratio of 62.2/37.0, which was also close to the atomic ratio of Nb5Si3.

tab1
Table 1: EDX results of the four samples in Figure 3.
fig3
Figure 3: SEM images of four samples with different Nb/Si ratio: (a) Nb-10Si; (b) Nb-20Si; (c) Nb-30Si; (d) Nb-37.5Si.

To address the phase composition of the products in the four figures, the XRD patterns were obtained in Figure 4. All of the samples have a phase of Nb5Si3 (JCPDS: 30-0874) as indicated with solid circle. Only the alloys of the Nb-10Si, Nb-20Si, and Nb-30Si had a phase of Nb (JCPDS: 35-0789) shown in Figures 4(a), 4(b), and 4(c). Based on the data of the XRD, SEM, and EDX, three critical conclusions can be drawn. First, all the samples were composed of two phases: Nb and Nb5Si3, which were the two phases in NbSi alloys. Second, in Figures 3(a), 3(b) and 3(c), the small white particles were Nb phase, and grey phase was Nb5Si3. Third, the Nb-37.5Si sample was completely composed of Nb5Si3 phase after electrolysis.

fig4
Figure 4: XRD patterns of four samples with different Nb/Si ratio: (a) Nb-10Si; (b) Nb-20Si; (c) Nb-30Si; (d) Nb-37.5Si.

4. Conclusion

We used four mixed powders of different Nb-Si compositions (Nb-10Si, Nb-20Si, Nb-30Si, and Nb-37.5Si) for NbSi alloys preparation. NbSi alloys can be prepared by direct electrochemical reduction method in molten CaCl2 at 900°C, which is an easy and one-plot procedure. After electrolysis, Nb phase showed white scattered particles in the grey Nb5Si3 phase under SEM. XRD, and EDX results have proved that the NbSi alloys were successfully obtained, which had paved a creative way for production of alloys with direct electrochemical reduction method.

Acknowledgments

The authors are grateful for the Science and Technology Ministry of China for the financial support to the national high technology project.

References

  1. M. Singh and D. R. Behrendt, “Reactive melt infiltration of silicon-niobium alloys in microporous carbons,” Journal of Materials Research, vol. 9, pp. 1701–1708, 1994.
  2. C. L. Ma, A. Kasama, R. Tanaka, and S. Hanada, “Development of Nb-Nb-silicide in-situ composites,” Transactions of Metal Heat Treatment, vol. 21, p. 2, 2000.
  3. M. G. Mendiratta and D. M. Dimiduk, “Microstructures and mechanical behaviors of 2-phase niobium silicide-niobium alloys,” in Proceedings of the Material Research Society Symposia Proceeding, vol. 133, MRS, Pittsburgh, Pa, USA, 1989.
  4. W. Y. Kim, H. Tanaka, A. Kasama, and S. Hanada, “Microstructure and room temperature fracture toughness of Nbss/Nb5Si3 in situ composites,” Intermetallics, vol. 9, no. 9, pp. 827–834, 2001. View at Publisher · View at Google Scholar · View at Scopus
  5. X. Y. Yan and D. J. Fray, “Production of niobium powder by direct electrochemical reduction of solid Nb2O5 in a eutectic CaCl2-NaCl melt,” Metallurgical and Materials Transactions B, vol. 33, pp. 685–693, 2002.
  6. T. Nohira, K. Yasuda, and Y. Ito, “Pinpoint and bulk electrochemical reduction of insulating silicon dioxide to silicon,” Nature Materials, vol. 2, no. 6, pp. 397–401, 2003. View at Publisher · View at Google Scholar · View at Scopus
  7. G. Z. Chen, D. J. Fray, and T. W. Farthing, “Direct electrochemical reduction of titanium dioxide to titanium in molten calcium chloride,” Nature, vol. 407, no. 6802, pp. 361–364, 2000. View at Publisher · View at Google Scholar · View at Scopus
  8. F. K. Meng and H. M. Lu, “Study on a new electrolysis technology of preparing high Nb bearing TiAl alloy from metal oxides,” in EPD Congress Proceedings, pp. 711–717, 2009.
  9. G. Z. Chen, E. Gordo, and D. J. Fray, “Direct electrolytic preparation of chromium powder,” Metallurgical and Materials Transactions B, vol. 35, pp. 223–233, 2004.
  10. F. Meng and H. Lu, “Direct electrochemical preparation of NbSi alloys from mixed oxide preform precursors,” Advanced Engineering Materials, vol. 11, no. 3, pp. 198–201, 2009. View at Publisher · View at Google Scholar
  11. A. J. M. Wood, R. C. Copcutt, G. Z. Chen, and D. J. Fray, “Electrochemical fabrication of nickel manganese gallium alloy powder,” Advanced Engineering Materials, vol. 5, no. 9, pp. 650–653, 2003. View at Publisher · View at Google Scholar
  12. K. Dring, R. Bhagat, M. Jackson, R. Dashwood, and D. Inman, “Direct electrochemical production of Ti-10W alloys from mixed oxide preform precursors,” Journal of Alloys and Compounds, vol. 419, no. 1-2, pp. 103–109, 2006. View at Publisher · View at Google Scholar · View at Scopus