Syngas Generation from Methane Using a Chemical-Looping Concept: A Review of Oxygen Carriers

Li, Kongzhai; Wang, Hua; Wei, Yonggang

doi:https://doi.org/10.1155/2013/294817

Journal of Chemistry

On this page

Abstract Introduction Conclusions Acknowledgments References Copyright Related Articles

Review Article | Open Access

Volume 2013 | Article ID 294817 | https://doi.org/10.1155/2013/294817

Syngas Generation from Methane Using a Chemical-Looping Concept: A Review of Oxygen Carriers

Kongzhai Li,^1,2Hua Wang,¹and Yonggang Wei¹

Academic Editor: Alexander Tatarinov

Received30 Jun 2012

Accepted16 Jan 2013

Published27 Feb 2013

Abstract

Conversion of methane to syngas using a chemical-looping concept is a novel method for syngas generation. This process is based on the transfer of gaseous oxygen source to fuel (e.g., methane) by means of a cycling process using solid oxides as oxygen carriers to avoid direct contact between fuel and gaseous oxygen. Syngas is produced through the gas-solid reaction between methane and solid oxides (oxygen carriers), and then the reduced oxygen carriers can be regenerated by a gaseous oxidant, such as air or water. The oxygen carrier is recycled between the two steps, and the syngas with a ratio of H₂/CO = 2.0 can be obtained successively. Air is used instead of pure oxygen allowing considerable cost savings, and the separation of fuel from the gaseous oxidant avoids the risk of explosion and the dilution of product gas with nitrogen. The design and elaboration of suitable oxygen carriers is a key issue to optimize this method. As one of the most interesting oxygen storage materials, ceria-based and perovskite oxides were paid much attention for this process. This paper briefly introduced the recent research progresses on the oxygen carriers used in the chemical-looping selective oxidation of methane (CLSOM) to syngas.

1. Introduction

Methane, the principal constituent of natural gas and coal-bed gas, is an excellent raw material for production of fuels and chemicals [1]. Conversion of methane to value-added products can be achieved in two ways, either via syngas (a mixture of CO and H₂) as an intermediate or directly into C₂ and higher hydrocarbons. Since the direct catalytic conversion of methane is inefficient, almost all the commercial processes for large scale chemical utilization of methane such as Fischer-Tropsch synthesis, methanol, or dimethyl ether production involve syngas [2].

Syngas generation from methane can be achieved in three routes: water steam reforming (SMR), carbon dioxide reforming (CDR), and partial oxidation of methane (POM) [3]. The two reforming reactions are all highly endothermic and operated at high temperature and high pressure, termed as costly chemical processes. POM technology, by contrast, is a mildly exothermic route, which makes the process less energy and capital cost than the reforming routes. In addition, it also allows excellent syngas yield in compact reactors due to the fast reaction rate and product selectivity [3–5]. However, this technology requires additional safety measures to avoid the risk of explosion due to the premixing of CH₄/O₂ mixture and pure oxygen supply to avoid the dilution of syngas by nitrogen and the formation of [6], which partly offset its advantages in the saving of energy and capital cost. To avoid such problems, a chemical-looping concept was proposed to use in the POM technology.

2. Chemical-Looping Concept

The term “chemical looping” is a new concept for fuels conversion, which is based on the transfer of oxygen from gaseous oxygen source to the fuel by means of a cycling process using solid oxides as oxygen carriers to avoid direct contact between fuel and gaseous oxygen [7]. In the case of methane as fuel, the schematic of the chemical-looping process was shown in Figure 1. Lattice oxygen in oxygen carriers was used to oxidize methane, and then the reduced oxygen carriers can be reoxidized by gaseous oxidant to restore its initial state. Two interconnected reactors or fluidized-bed system are used in this technique to achieve the circulation of oxygen carrier between the oxidizing and reducing steps.

The first design using this concept was developed for power generation, which is known with the general term “chemical looping combustion” (CLC). For this process, the oxygen carrier can convert fuels to H₂O and CO₂, and the reduced oxygen carriers must be reoxidized by air. Because of the separation of fuels from air, this technology is identified as owning inherent advantages for CO₂ separation with minimum energy losses [8]. Further designs of this concept were used in the syngas production from methane. After methane is oxidized to CO₂ and H₂O by oxygen carriers, the by-product gases (CO₂ and H₂O) were introduced into another reactor (reforming reactor) to reform with additional methane to produce syngas in the presence of a reforming catalyst (e.g., Ni/Al₂O₃) [9, 10]. Since the additional reforming process is a highly endothermic reaction needing large energy supply, this technology is less-than-ideal for syngas generation.

On the other hand, the direct generation of syngas by the reaction between oxygen carriers and methane is more acceptable, but this process needs an oxygen carrier owning ability to selectively oxidize methane. This vision was firstly realized over CeO₂ oxygen carrier, and the authors also proposed that the reduced oxygen carrier can be reoxidized by H₂O with obtaining H₂ simultaneously [11, 12]. In this case, the design and elaboration of suitable oxygen carriers with high activity, selectivity, and redox stability for methane selective oxidation is a key issue for this technology.

Comparing with the traditional POM process, the chemical-looping concept allows air instead of pure oxygen as oxygen source without the dilution of product gas with nitrogen, which brings about considerable cost saving. When using H₂O as an oxidant (two-step SRM process), it gives the possibility of coproduction of pure hydrogen without separating equipments and syngas with a H₂/CO ratio of 2.0 which is ideal for the major downstream processes such as methanol production or Fischer-Tropsch synthesis. The present paper would mainly discuss the progresses on the oxygen carriers for this technology.

3. Oxygen Carriers for Chemical-Looping Selective Oxidation of Methane (CLSOM)

Chemical-looping concept involves the use of a redox cycle process of chosen oxygen carriers to implement the selective oxidation of methane to syngas. The yield of syngas depends on the activity and selectivity of the oxygen in oxygen carriers. In this case, selection of the oxygen carrier, which relies on the understanding of reaction mechanism of methane selective oxidation in the absence of the gaseous oxygen, is considered as one of the most essential components of the CLSOM process.

For the CLC process, it is proposed that the oxygen carriers must own the following properties in chemistry [7, 8]: (i) sufficient oxygen storage and transport capacity; (ii) high reactivity in both reduction and oxidation cycles; (iii) ability to completely combust a fuel; (iv) ability of resistant to agglomeration and carbon deposition. This list also applies to the CLSOM oxygen carriers except the third one (iii), which should be changed to “ability to selectively oxidize a fuel.”

Most of previous technical literatures on CLSOM focused on development of suitable oxygen carrier materials for methane selective oxidation. Ceria-based materials and perovskite-type oxides were paid the most attention due to their high lattice oxygen activity, excellent redox properties, and good thermal stability.

3.1. CeO₂-Based Oxygen Carriers

The selective oxidation of methane to CO and H₂ (syngas) by gas-solid reaction was firstly achieved over CeO₂ oxygen carrier [11, 12]. The reaction between methane and CeO₂ may occur in four equations: The thermodynamic considerations of the reactions in (1)–(4) were shown in Figure 2. It is clear that the complete oxidation of methane to CO₂ and H₂O by CeO₂ (reaction (1)) is thermodynamically unfeasible under 1000°C, and the syngas generation through selective oxidation of methane by CeO₂ is favorable with the reaction temperatures ≥ 700°C. The experimental results supported the thermodynamic analysis [12]. It shows that syngas with H₂/CO ratio of 2.0 was indeed produced via the gas-solid reaction between methane and CeO₂ at 700°C, and the reduction degree of CeO₂ reached 21% with platinum as a catalyst, suggesting that almost all the CeO₂ was reduced to Ce₂O₃. This indicates that the oxidation of methane over CeO₂ may occur follow (2) in the presence of platinum.

Fathi et al. [13] also investigated the reaction between methane and CeO₂ with γ-Al₂O₃ as a support and Pt or Rh as a promoter. They observed that the selectivity to syngas depends on the reduction degree of CeO₂. Numbers of CO₂ and H₂O were produce in the early stage of the reaction, and then the syngas selectivity increased quickly with the reduction degree of cerium oxide. Pt or Rh promoters could lower the temperature necessary to reduce the cerium oxide but also result in the formation of carbon deposition. Pantu et al. [6] found that the surface area of Pt/CeO₂ sample affects the formation rate of syngas: methane conversion slightly increased, and syngas selectivity slightly decreased with increasing surface area. This indicates that ether high or low surface area of oxygen carrier will reduce the yield of syngas. They also observed that there was no significant effect of Pt loading on the activity of CeO₂ for methane oxidation, and the differences in metal dispersion on CeO₂ are not substantial.

Wei et al. [14] investigated the effects of CeO₂ loading on the reactivity of CeO₂/γ-Al₂O₃ oxygen carrier for methane selective oxidation in the absence of platinum catalyst. The results showed that higher CeO₂ loading will seriously decrease the selectivity of syngas. The other major innovation in this paper is the use of molten salt system as thermal carrier, which can avoid the agglomeration of circulating particles and improve the thermal efficiency of the whole reaction system.

It is generally accepted that the addition of Zr⁴⁺ could enhance the oxygen storage capacity by increasing the oxygen vacancies of ceria. Otsuka et al. [15] tested the reactivity of for the direct conversion of methane to syngas by gas-solid reactions. The formation rates of H₂ and CO were increased, and the activation energy was remarkably decreased due to the incorporation of ZrO₂ into CeO₂. The conversion of CH₄ to H₂ and CO could be achieved at a temperature as low as 500°C by using Ce_0.8Zr_0.2O₂ in the presence of Pt, which is 200°C lower than CeO₂ sample. Pantu et al. [6] observed that addition of ZrO₂ to CeO₂ significantly increases the methane oxidation rate and the reducibility of the CeO₂ but decreases the selectivity to H₂ and CO. Wei et al. [16] also reported a similar observation on using as oxygen carrier, but they found that the ZrO₂-rich materials own better activity and stability.

Kang and Eyring [17, 18] investigated the activity of the Ce-Zr-Tb-O system for methane oxidation and found that the oxygen transfer capacity and the oxygen storage capacity are equally important for syngas generation. The reactivity of ceria-zirconia oxides doped by Pr, Gd, or La for methane conversion was also investigated by CH₄-TPR technology and pulse reduction experiments, and it is proved that Pr-doped sample showed good activity for syngas generation [19]. The reaction between methane and Ce–Zr-Pr-O oxygen carrier with Pt as catalyst at high temperatures is controlled by the lattice oxygen diffusion, while the reactivity of weak bound surface oxygen determine the activity of the mixed oxides at the lowest temperature (~550°C).

Sadykov et al. [20] designed incorporating Sm³⁺ and Bi³⁺ cations into the ceria lattice to enhance the oxygen mobility while increasing the rate of methane dissociation by supporting Pt, and the results were also compared with the Pt/Ce-Zr-La-O mixed oxides. It showed that only the Ce-Sm-based oxide system is promising for methane selective oxidation by gas-solid reaction due to a high mobility and reactivity of the lattice oxygen, good selectivity for syngas generation, and high stability in redox cycles. The selective conversion of methane into syngas by lattice oxygen depends not only on the route of its primary activation (i.e., on supported Pt clusters) but on the features of activated fragments transformation on the support surface as well, provided the lattice oxygen mobility that is comparable.

Several reports showed that the oxidation activity and redox property of the ceria can be strongly enhanced by the addition of Fe³⁺ due to the formation of surface structural defects and Ce-Fe solid solution [21–25]. In addition, the modified iron oxides can also produce CO and H₂ through reduction with methane in an appropriate condition [26, 27], and that the iron species can strongly enhance the adsorption of methane [28]. Fe₂O₃ is possibly the most common and one of the cheapest metal oxides available in nature, and Fe³⁺ are very suitable as an dopant to improve the performance of ceria [29, 30]. Combination of CeO₂ and Fe₂O₃ gives people very high expectation to obtain attractive oxygen carriers for methane selective oxidation. Given the above, the investigation on the possibility of using CeO₂-Fe₂O₃ composite as oxygen carrier for methane selective oxidation attracted much attention [31–41]_.

It was reported that the CeO₂-Fe₂O₃ mixed oxides own good activity, selectivity, and stability for syngas generation through gas-solid reactions, as shown in Figure 3, and the interaction between exposed Fe₂O₃ and Ce-Fe solid solution in the oxygen carrier plays an important role on the syngas generation [36]. In addition, the dispersion of surface Fe₂O₃ and the formation of the Ce-Fe solid solution were enhanced by the redox treatment, which made the oxygen carrier very stable in the successive generation of syngas [36]. The selectivity of Ce-Fe mixed oxides for syngas production is strongly affected by the specific surface area of oxygen carriers, and high surface area would result in abundant surface adsorbed oxygen, favoring the complete oxidation of methane to carbon dioxide and water [42].

For the reaction process between methane and Ce-Fe mixed oxides [36], methane was found to adsorb and activate on the reduced iron and cerium sites, and the subsequent oxidation of activated methane relied on the lattice oxygen mobility of the oxygen carrier. The dispersion of surface iron species and the consistence of oxygen vacancy in Ce-Fe mixed oxides in turn markedly affect the formation rate of syngas, and the strong interactions between dispersed Fe species and Ce-Fe solid solution have a distinct positive effect on the catalytic activity for methane selective oxidation.

Comparison of Ce-Zr and Ce-Fe mixed oxides demonstrated that the two samples showed similar activity for methane oxidation, but the Ce-Fe sample revealed higher selectivity of syngas, as shown in Figure 4 [33]. Addition of ZrO₂ into CeO₂-Fe₂O₃ system could enhance the interaction between iron and cerium oxides via increasing the oxygen vacancy concentration and improving the dispersion of free Fe₂O₃, which improved the activity of Ce-Fe mixed oxides for methane selective oxidation. However, heavy loading of ZrO₂ would lead to a phase segregation of CeO₂ and Fe₂O₃ from the Ce-Fe solid solution, resulting in a decrease in syngas selectivity [34].

(a)

(b)

The effect of supports (Al₂O₃, SiO₂, and MgO) on the activity and selectivity of Ce-Fe-Zr mixed oxides for methane selective oxidation was also investigated [40]. Al₂O₃ support could result in the complete oxidation of methane, and SiO₂ obvious reduced the reactivity of Ce-Fe-Zr mixed oxides. On the other hand, MgO support strongly enhanced the activity and selectivity of Ce-Fe-Zr oxygen carriers for syngas generation.

Ce-Cu-O, Ce-Mn-O, and Ce-Nb-O and Ce-Ni-O were also considered as an oxygen carrier for methane oxidation [38, 43–45]. Compared with the Ce-Fe mixed oxides, Ce-Cu-O and Ce-Mn-O oxygen carriers are more favorable to completely oxidize methane [38], and the Ce-Ni-O would result in the decomposition of methane when the Ni loading is too high [44]. For Ce-Nb-O system, the further oxidation of hydrogen to water was observed, and the CO and H₂O were the main production [45]. For all ceria-based oxygen carriers, the reoxidation process by air is very easy to accomplish.

3.2. Perovskite Oxygen Carriers

Perovskite oxides with an ABO₃-type crystal structure usually exhibit excellent redox properties, high oxygen mobility, and thermal stability, which can be used in many reactions related to a redox process, such as catalytic purification of automotive exhaust and solid oxide fuel cell (SOFC) [46–50]. As a famous perovskite oxides, LaFeO₃ was firstly chosen to selectively oxidize methane by Dai et al. [51, 52], and its performance was compared with NdFeO₃ and EuFeO₃. The oxygen storage and transport ability of AFeO₃ (A = La, Nd, and Eu) is related to its Fe–O bond distance and shorter distance given lower activity of oxygen. The reaction rate between methane AFeO₃ strongly depends on the reaction temperature, and high-temperature (>800°C) is necessary for obtaining a high syngas yield. The LaFeO₃ oxide exhibits the best performance among these tested AFeO₃ oxides (A = La, Nd, and Eu) for syngas production, and it also maintains high catalytic activity and structural stability in the redox experiment between methane and air at 900°C. It was also observed that the reduction of LaFeO₃ by methane was performed through a reduction of Fe³⁺ to Fe²⁺, and further reduction is very difficult [53]. They also investigated the redox property of LaFeO₃ for successive generation of syngas in a circulating-fluidized bed (CFB) reactor [54]. It showed that methane could be oxidized to syngas by lattice oxygen with high selectivity, and the depleted oxygen species could be regenerated in a CFB condition. The methane conversion remains at 60%–70% with the CO selectivity of ca. 96% during the 30 redox cycles. However, this paper did not involve the mechanical performance of the oxygen carriers in the redox process, and it is proposed that the attrition resistance for CFB process should be paid much attention.

Li et al. [55, 56] added Sr into the LaFeO₃ system to partially substitute the sites of La and investigated that performance of the La_0.8Sr_0.2FeO₃ oxide for methane selective oxidation. They proposed that there are two kinds of oxygen species on the oxide: (i) the active oxygen species (weakly bound oxygen species) which are responsible for complete oxidation of methane and (ii) the weaker oxygen species (strongly bound oxygen species) which are responsible for partial oxidation of methane to syngas. This is similar with the observation by Greish et al. [57]. Methane reacts firstly with the active oxygen species to form CO₂ and H₂O, and then the weaker oxygen species can oxidize methane to CO and H₂ with high selectivity.

On the other hand, substituting La for Sr was found to increase the oxygen capacity of these materials but reduce the selectivity to syngas and the reactivity with CH₄ [58]. Addition of Cr, Ni, and Cu into the La-Sr-Fe-O perovskite system to partially replace the Fe sites could improve the reactivity for methane conversion [59], while incorporation of Co ions into La-Sr-Fe-O mixed oxides could enhance the activity of this material for methane combustion [58] and reduce the stability under redox testing [60]. The La_0.7Sr_0.3Cr_0.1Fe_0.9O₃ with physically mixed NiO as a catalyst showed good activity and stability in the redox testing [59]. The improvement on the syngas production and stability of material was also observed over the NiO/ system due to the presence of exposed NiO particles, but the presence of NiO also improved the catalytic activity for methane decomposition, resulting in the formation of carbon deposition [61].

(M = Mn, Ni) and LaMnO_3 −αF_β perovskite oxides were also investigated as oxygen carriers for methane oxidation [62]. It is proposed that the reactivity and selectivity of lattice oxygen depend on (i) B-site element, (ii) degree of substitution of La with Sr, and (iii) fluorination of the perovskite oxide. The with relatively low degree of Sr-substitution and the fluorinated LaMnO_3−αF are suitable oxygen carriers for syngas generation. The high substitution degree of La by Sr increases the reactivity of lattice oxygen but decreases the selectivity to syngas. Evdou et al. [61] observed that the reduction degree of oxides by methane relies on the Sr content and the reaction temperature.

perovskite oxides with nickel as a catalyst were also investigated for methane oxidation in the absence of gas phase oxygen [63]. Based on the temperature-programmed surface reaction of methane (TPSR-CH₄) and pulses reaction results, they found that the reducibility of B cation (ABO₃) and the anionic conductivity of the material strongly influence the activity and selectivity of oxygen carriers. It is also observed that Ni/BaTi_0.3In_0.7O₃ oxygen carrier was more stable than Ni/BaTiO₃ due to the existence of Ni-In alloys which is relatively inert for catalyzing the cracking reaction.

3.3. Other Oxygen Carriers

Fe₂O₃ as oxygen carrier was proved to own the ability for methane combustion [7, 8], but addition of other suitable oxides can modify the selectivity of its lattice oxygen for selective oxidation of methane to syngas. Fe₂O₃-Rh₂O₃/Y₂O₃ and Fe₂O₃-Cr₂O₃-MgO oxides were found to be active to produce syngas with a moderate methane conversion and selectivity [64]. It is also proved that combining CuO and Fe₂O₃ to form a Cu-ferrite could obtain a suitable oxygen carrier for methane selective oxidation. Cha et al. [65, 66] investigated the reactivity of /Ce-ZrO₂ () for methane selective oxidation, and the results showed that the Cu-ferrite suppressed carbon deposition and promoted the reactivity with methane to produce syngas. On the other hand, since the lattice oxygen from Fe₂O₃ to Fe₃O₄ can completely oxidize methane to CO₂ and H₂O, the redox of FeO/Fe₃O₄ was proposed to convert methane to syngas by a chemical looping step [67].

NiO-based materials were also used for the methane selective oxidation, but significant amount of CO₂ and H₂O was observed in the products over NiO, NiO/γ-Al₂O₃, NiO/α-Al₂O₃, and NiO/Mg-ZrO₂ oxygen carriers [68–73]. During the reaction between methane and NiO-based oxides, the syngas yield depends on the oxidation degree of the oxygen carriers: highly oxidized oxide particles resulted in the formation of CO₂ and H₂O, while reduced particles could produce CO and H₂ [70, 74]. Addition of Cr₂O₃ into NiO-MgO system could change reactivity of the lattice oxygen in the materials, and the fully oxidized NiO-Cr₂O₃-MgO produced H₂ and CO with high selectivity during the reaction with CH₄ [64, 75]. The appearance of NiAl₂O₄ also could reduce the activity of oxygen in the material and promote the formation of H₂ and CO [76].

Based on the previous discussions, CeO₂-based oxygen carrier could convert methane into syngas at relatively low temperatures (ca. 700°C) in the presence of Pt promoter, but the redox stability of the oxygen carriers needs to be improved. The perovskite-type oxygen carriers own high selectivity and redox stability for syngas generation, but they are only active at high temperatures (ca. 850°C). For the Fe₂O₃- and NiO-based oxygen carriers, a large number of CO₂ and H₂O were produced during the gas-solid reaction between oxygen carrier and methane. Although addition of suitable promoters could improve the selectivity of oxygen carriers for syngas generation, but it also reduced the reactivity for methane conversion. Among the different oxygen carriers, perovskite-type oxygen carriers are more competitive for the CLSOM process, if the activity could be enhanced by the structure modifications. On the other hand, the use of the various combinations of catalysts (e.g., combinations of perovskite-type or CeO₂-ZrO₂ oxygen carriers with Ni or Fe species) may also achieve the greater efficiency for syngas generation.

4. Conclusions

Chemical-looping selective oxidation of methane (CLSOM) is a promising, energy-efficient, and low-cost route for syngas generation. However, at the present time, this technology is not fully established for large-scale implementation, and valuable researches need to be developed to address the important issues of this technology. Nowadays, numbers of works were performed on this technology, and most of previous technical literatures had been focused on the development of suitable oxygen carrier materials. After reviewing such references, it is found that a suitable oxygen carrier should own abundant active sites for methane activation, high oxygen storage capacity, and good oxygen mobility. This finding gives useful references for the further developing highly efficient oxygen carriers.

Due to the two-step redox process, the chemical engineering of whole process is actually a key factor for success in practical application, and the specific selected reactor design is very critical. The mechanical performance of the oxygen carriers should be paid much attention when a fluidized bed reactor is used. In addition, since the reaction between methane and oxygen carriers is endothermic, while the reoxidation of reduced oxygen carriers is an exothermic reaction, the energy efficiency of the whole process strongly depends on the transfer of the heat from the exothermic reaction to the endothermic reaction. This issue is also very important for the practical application of this technology.

Acknowledgments

This paper was supported by the National Nature Science Foundation of China (Project nos. 51004060 and 51174105), National Excellent Doctoral Dissertation Development Foundation of Kunming University of Science and Technology, Natural Science Foundation of Yunnan Province (no. 2010ZC018), and a school-enterprise cooperation project from Jinchuan Corporation (no. Jinchuan 201115).

References

J. R. Rostrup-Nielsen, “Fuels and energy for the future: the role of catalysis,” Catalysis Reviews, vol. 46, no. 3-4, pp. 247–270, 2004.
View at: Publisher Site | Google Scholar
A. Holmen, “Direct conversion of methane to fuels and chemicals,” Catalysis Today, vol. 142, no. 1-2, pp. 2–8, 2009.
View at: Publisher Site | Google Scholar
B. C. Enger, R. Lødeng, and A. Holmen, “A review of catalytic partial oxidation of methane to synthesis gas with emphasis on reaction mechanisms over transition metal catalysts,” Applied Catalysis A, vol. 346, no. 1-2, pp. 1–27, 2008.
View at: Publisher Site | Google Scholar
P. M. Torniainen, X. Chu, and L. D. Schmidt, “Comparison of monolith-supported metals for the direct oxidation of methane to syngas,” Journal of Catalysis, vol. 146, no. 1, pp. 1–10, 1994.
View at: Google Scholar
L. Bobrova, N. Vernikovskaya, and V. Sadykov, “Conversion of hydrocarbon fuels to syngas in a short contact time catalytic reactor,” Catalysis Today, vol. 144, no. 3-4, pp. 185–200, 2009.
View at: Publisher Site | Google Scholar
P. Pantu, K. Kim, and G. R. Gavalas, “Methane partial oxidation on Pt/CeO₂-ZrO₂ in the absence of gaseous oxygen,” Applied Catalysis A, vol. 193, no. 1-2, pp. 203–214, 2000.
View at: Google Scholar
J. Adanez, A. Abad, F. Garcia-Labiano, P. Gayan, and L. F. de Diego, “Progress in chemical-looping combustion and reforming technologies,” Progress in Energy and Combustion Science, vol. 38, no. 2, pp. 215–282, 2012.
View at: Publisher Site | Google Scholar
M. M. Hossain and H. I. de Lasa, “Chemical-looping combustion (CLC) for inherent CO₂ separations-a review,” Chemical Engineering Science, vol. 63, no. 18, pp. 4433–4451, 2008.
View at: Publisher Site | Google Scholar
F. vanlooij, J. C. van Giezen, E. R. Stobbe, and J. W. Geus, “Mechanism of the partial oxidation of methane to synthesis gas on a silica-supported nickel catalyst,” Catalysis Today, vol. 21, no. 2-3, pp. 495–503, 1994.
View at: Google Scholar
E. R. Stobbe, B. A. De Boer, and J. W. Geus, “The reduction and oxidation behaviour of manganese oxides,” Catalysis Today, vol. 47, no. 1–4, pp. 161–167, 1999.
View at: Google Scholar
K. Otsuka, T. Ushiyama, and I. Yamanaka, “Partial oxidation of methane using the redox of cerium oxide,” Chemistry Letters, pp. 1517–1520, 1993.
View at: Google Scholar
K. Otsuka, Y. Wang, E. Sunada, and I. Yamanaka, “Direct partial oxidation of methane to synthesis gas by cerium oxide,” Journal of Catalysis, vol. 175, no. 2, pp. 152–160, 1998.
View at: Google Scholar
M. Fathi, E. Bjorgum, T. Viig, and O. A. Rokstad, “Partial oxidation of methane to synthesis gas: elimination of gas phase oxygen,” Catalysis Today, vol. 63, no. 2–4, pp. 489–497, 2000.
View at: Publisher Site | Google Scholar
Y. Wei, H. Wang, F. He, X. Ao, and C. Zhang, “CeO₂ as the oxygen carrier for partial oxidation of methane to synthesis gas in molten salts: thermodynamic analysis and experimental investigation,” Journal of Natural Gas Chemistry, vol. 16, no. 1, pp. 6–11, 2007.
View at: Publisher Site | Google Scholar
K. Otsuka, Y. Wang, and M. Nakamura, “Direct conversion of methane to synthesis gas through gas-solid reaction using CeO₂-ZrO₂ solid solution at moderate temperature,” Applied Catalysis A, vol. 183, no. 2, pp. 317–324, 1999.
View at: Google Scholar
Y. G. Wei, H. Wang, K. Z. Li, M. C. Liu, and X. Q. Ao, “Preparation and performance of Ce/Zr mixed oxides for direct conversion of methane to syngas,” Journal of Rare Earths, vol. 25, pp. 110–114, 2007.
View at: Google Scholar
Z. C. Kang and L. Eyring, “Hydrogen production from methane and water by lattice oxygen transfer with Ce_0.70Zr_0.25Tb_0.05O_2−x,” Journal of Alloys and Compounds, vol. 323-324, pp. 97–101, 2001.
View at: Publisher Site | Google Scholar
Z. C. Kang and L. Eyring, “Lattice oxygen transfer in fluorite-type oxides containing Ce, Pr, and/or Tb,” Journal of Solid State Chemistry, vol. 155, no. 1, pp. 129–137, 2000.
View at: Publisher Site | Google Scholar
V. A. Sadykov, N. N. Sazonova, A. S. Bobin et al., “Partial oxidation of methane on Pt-supported lanthanide doped ceria-zirconia oxides: effect of the surface/lattice oxygen mobility on catalytic performance,” Catalysis Today, vol. 169, no. 1, pp. 125–137, 2011.
View at: Publisher Site | Google Scholar
V. A. Sadykov, T. G. Kuznetsova, G. M. Alikina et al., “Ceria-based fluorite-like oxide solid solutions as catalysts of methane selective oxidation into syngas by the lattice oxygen: synthesis, characterization and performance,” Catalysis Today, vol. 93–95, pp. 45–53, 2004.
View at: Publisher Site | Google Scholar
C. Liu, L. Luo, and X. Lu, “Preparation of mesoporous Ce_1−x Fe_xO₂ mixed oxides and their catalytic properties in methane combustion,” Kinetics and Catalysis, vol. 49, no. 5, pp. 676–681, 2008.
View at: Publisher Site | Google Scholar
J. Y. Luo, M. Meng, J. S. Yao et al., “One-step synthesis of nanostructured Pd-doped mixed oxides MO_x-CeO₂ (M = Mn, Fe, Co, Ni, Cu) for efficient CO and C₃H₈ total oxidation,” Applied Catalysis B, vol. 87, no. 1-2, pp. 92–103, 2009.
View at: Publisher Site | Google Scholar
H. Lv, H. Y. Tu, B. Y. Zhao, Y. J. Wu, and K. A. Hu, “Synthesis and electrochemical behavior of Ce_1−xFe_xO_2−δ as a possible SOFC anode materials,” Solid State Ionics, vol. 177, no. 39-40, pp. 3467–3472, 2007.
View at: Publisher Site | Google Scholar
H. Lv, D. J. Yang, X. M. Pan et al., “Performance of Ce/Fe oxide anodes for SOFC operating on methane fuel,” Materials Research Bulletin, vol. 44, no. 6, pp. 1244–1248, 2009.
View at: Publisher Site | Google Scholar
C. Liang, Z. Ma, H. Lin et al., “Template preparation of nanoscale Ce_xFe_1−xO₂ solid solutions and their catalytic properties for ethanol steam reforming,” Journal of Materials Chemistry, vol. 19, no. 10, pp. 1417–1424, 2009.
View at: Publisher Site | Google Scholar
S. Takenaka, M. Serizawa, and K. Otsuka, “Formation of filamentous carbons over supported Fe catalysts through methane decomposition,” Journal of Catalysis, vol. 222, no. 2, pp. 520–531, 2004.
View at: Publisher Site | Google Scholar
O. Nakayama, N. O. Ikenaga, T. Miyake, E. Yagasaki, and T. Suzuki, “Partial oxidation of CH₄ with air to produce pure hydrogen and syngas,” Catalysis Today, vol. 138, no. 3-4, pp. 141–146, 2008.
View at: Publisher Site | Google Scholar
S. Fukuda, T. Hino, and T. Yamashina, “Desorption processes of hydrogen and methane from clean and metal-deposited graphite irradiated by hydrogen ions,” Journal of Nuclear Materials, vol. 162–164, no. C, pp. 997–1003, 1989.
View at: Google Scholar
G. Li, R. L. Smith, and H. Inomata, “Synthesis of nanoscale Ce_1−xFe_xO₂ solid solutions via a low-temperature approach,” Journal of the American Chemical Society, vol. 123, no. 44, pp. 11091–11092, 2001.
View at: Publisher Site | Google Scholar
F. J. Pérez-Alonso, M. L. Granados, M. Ojeda et al., “Chemical structures of coprecipitated Fe-Ce mixed oxides,” Chemistry of Materials, vol. 17, no. 9, pp. 2329–2339, 2005.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, and M. Liu, “Catalytic performance of cerium iron complex oxides for partial oxidation of methane to synthesis gas,” Journal of Rare Earths, vol. 26, no. 5, pp. 705–710, 2008.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, and M. Liu, “Preparation and characterization of Ce_1−xFe_xO₂ complex oxides and its catalytic activity for methane selective oxidation,” Journal of Rare Earths, vol. 26, no. 2, pp. 245–249, 2008.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, and D. Yan, “Direct conversion of methane to synthesis gas using lattice oxygen of CeO₂-Fe₂O₃ complex oxides,” Chemical Engineering Journal, vol. 156, no. 3, pp. 512–518, 2010.
View at: Publisher Site | Google Scholar
K. Z. Li, H. Wang, Y. G. Wei, and D. X. Yan, “Partial oxidation of methane to syngas with air by lattice oxygen transfer over ZrO₂-modified Ce-Fe mixed oxides,” Chemical Engineering Journal, vol. 173, pp. 574–582, 2011.
View at: Publisher Site | Google Scholar
Y. Wei, H. Wang, and K. Li, “Ce-Fe-O mixed oxide as oxygen carrier for the direct partial oxidation of methane to syngas,” Journal of Rare Earths, vol. 28, no. 4, pp. 560–565, 2010.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, and D. Yan, “Syngas production from methane and air via a redox process using Ce-Fe mixed oxides as oxygen carriers,” Applied Catalysis B, vol. 97, no. 3-4, pp. 361–372, 2010.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, X. Ao, and M. Liu, “Partial oxidation of methane to synthesis gas using lattice oxygen,” Progress in Chemistry, vol. 20, no. 9, pp. 1306–1314, 2008.
View at: Google Scholar
F. He, Y. Wei, H. Li, and H. Wang, “Synthesis gas generation by Chemical-looping reforming using Ce-based oxygen carriers modified with Fe, Cu, and Mn oxides,” Energy and Fuels, vol. 23, no. 4, pp. 2095–2102, 2009.
View at: Publisher Site | Google Scholar
X. Zhu, H. Wang, Y. Wei, K. Li, and X. Cheng, “Hydrogen and syngas production from two-step steam reforming of methane over CeO₂-Fe₂O₃ oxygen carrier,” Journal of Rare Earths, vol. 28, no. 6, pp. 907–913, 2010.
View at: Publisher Site | Google Scholar
X. Cheng, H. Wang, Y. Wei, K. Li, and X. Zhu, “Preparation and characterization of Ce-Fe-Zr-O(x)/MgO complex oxides for selective oxidation of methane to synthesize gas,” Journal of Rare Earths, vol. 28, no. 1, pp. 316–321, 2010.
View at: Publisher Site | Google Scholar
H. Kaneko, H. Ishihara, S. Taku, Y. Naganuma, N. Hasegawa, and Y. Tamaura, “Cerium ion redox system in CeO_2−xFe₂O₃ solid solution at high temperatures (1,273–1,673 K) in the two-step water-splitting reaction for solar H₂ generation,” Journal of Materials Science, vol. 43, no. 9, pp. 3153–3161, 2008.
View at: Publisher Site | Google Scholar
K. Li, H. Wang, Y. Wei, and D. Yan, “Transformation of methane into synthesis gas using the redox property of Ce-Fe mixed oxides: effect of calcination temperature,” International Journal of Hydrogen Energy, vol. 36, no. 5, pp. 3471–3482, 2011.
View at: Publisher Site | Google Scholar
K. Z. Li, H. Wang, Y. G. Wei, and M. C. Liu, “Partial oxidation of methane to syngas using lattice oxygen from ceria-based complex oxides oxygen carriers,” Journal of Fuel Chemistry and Technology, vol. 36, no. 1, pp. 83–88, 2008.
View at: Google Scholar
Y. Wei, H. Wang, K. Li, X. Zhu, and Y. Du, “Preparation and characterization of Ce_1−x NixO₂ as oxygen carrier for selective oxidation methane to syngas in absence of gaseous oxygen,” Journal of Rare Earths, vol. 28, no. 1, pp. 357–361, 2010.
View at: Publisher Site | Google Scholar
A. A. Yaremchenko, V. V. Kharton, S. A. Veniaminov, V. D. Belyaev, V. A. Sobyanin, and F. M. B. Marques, “Methane oxidation by lattice oxygen of CeNbO_4+δ,” Catalysis Communications, vol. 8, no. 3, pp. 335–339, 2007.
View at: Publisher Site | Google Scholar
U. Balachandran, J. T. Dusek, R. L. Mieville et al., “Dense ceramic membranes for partial oxidation of methane to syngas,” Applied Catalysis A, vol. 133, no. 1, pp. 19–29, 1995.
View at: Google Scholar
V. R. Choudhary, S. Banerjee, and B. S. Uphade, “Activation by hydrothermal treatment of low surface area ABO3-type perovskite oxide catalysts,” Applied Catalysis A, vol. 197, no. 2, pp. L183–L186, 2000.
View at: Google Scholar
N. E. Trofimenko and H. Ullmann, “Oxygen stoichiometry and mixed ionic-electronic conductivity of Sr_1−aCe_aFe_1−bCo_bO_3−x perovskite-type oxides,” Journal of the European Ceramic Society, vol. 20, no. 9, pp. 1241–1250, 2000.
View at: Google Scholar
M. van den Bossche and S. McIntosh, “The rate and selectivity of methane oxidation over La_0.75Sr_0.25Cr_xMn_1−xO_3−δ as a function of lattice oxygen stoichiometry under solid oxide fuel cell anode conditions,” Journal of Catalysis, vol. 255, no. 2, pp. 313–323, 2008.
View at: Publisher Site | Google Scholar
A. Khanfekr, K. Arzani, A. Nemati, and M. Hosseini, “Production of perovskite catalysts on ceramic monoliths with nanoparticles for dual fuel system automobiles,” International Journal of Environmental Science and Technology, vol. 6, no. 1, pp. 105–112, 2009.
View at: Google Scholar
X. P. Dai, R. J. Li, C. C. Yu, and Z. P. Hao, “Unsteady-state direct partial oxidation of methane to synthesis gas in a fixed-bed reactor using AFeO₃ (A = La, Nd, Eu) perovskite-type oxides as oxygen storage,” Journal of Physical Chemistry B, vol. 110, no. 45, pp. 22525–22531, 2006.
View at: Publisher Site | Google Scholar
X. P. Dai and C. C. Yu, “Nano-perovskite-based (LaMO₃) oxygen carrier for syngas generation by chemical-looping reforming of methane,” Chinese Journal of Catalysis, vol. 32, pp. 1411–1417, 2011.
View at: Google Scholar
O. Mihai, D. Chen, and A. Holmen, “Catalytic consequence of oxygen of lanthanum ferrite perovskite in chemical looping reforming of methane,” Industrial and Engineering Chemistry Research, vol. 50, no. 5, pp. 2613–2621, 2011.
View at: Publisher Site | Google Scholar
X. Dai, C. Yu, R. Li, Q. Wu, and Z. Hao, “Synthesis gas production using oxygen storage materials as oxygen carrier over circulating fluidized bed,” Journal of Rare Earths, vol. 26, no. 1, pp. 76–80, 2008.
View at: Publisher Site | Google Scholar
R. Li, C. Yu, X. Dai, and S. Shen, “Selective oxidation of methane to synthesis gas using lattice oxygen from perovskite La_0.8Sr_0.2FeO₃ catalyst,” Chinese Journal of Catalysis, vol. 23, no. 6, pp. 549–554, 2002.
View at: Google Scholar
R. J. Li, C. C. Yu, W. J. Ji, and S. K. Shen, “Methane oxidation to synthesis gas using lattice oxygen in La_1−xSrxFeO₃ perovskite oxides instead of molecular oxygen,” Studies in Surface Science and Catalysis, vol. 147, pp. 199–204, 2004.
View at: Google Scholar
A. A. Greish, L. M. Glukhov, E. D. Finashina et al., “Oxidative coupling of methane in the redox cyclic mode over the catalysts on the basis of CeO₂ and La₂O₂,” Mendeleev Communications, vol. 20, no. 1, pp. 28–30, 2010.
View at: Publisher Site | Google Scholar
M. Rydén, A. Lyngfelt, T. Mattisson, D. Chen, A. Holmen, and E. Bjørgum, “Novel oxygen-carrier materials for chemical-looping combustion and chemical-looping reforming; LaxSr_1−xFe_yCo_1−yO_3−δ perovskites and mixed-metal oxides of NiO, Fe₂O₃ and Mn₃O₄,” International Journal of Greenhouse Gas Control, vol. 2, no. 1, pp. 21–36, 2008.
View at: Publisher Site | Google Scholar
L. Nalbandian, A. Evdou, and V. Zaspalis, “La_1−xSr_xM_yFe_1−yO_3−δ perovskites as oxygen-carrier materials for chemical-looping reforming,” International Journal of Hydrogen Energy, vol. 36, no. 11, pp. 6657–6670, 2011.
View at: Publisher Site | Google Scholar
A. Murugan, A. Thursfield, and I. S. Metcalfe, “A chemical looping process for hydrogen production using iron-containing perovskites,” Energy & Environmental Science, vol. 4, pp. 4639–4649, 2011.
View at: Publisher Site | Google Scholar
A. Evdou, V. Zaspalis, and L. Nalbandian, “La_1−xSr_xFeO_3−δ perovskites as redox materials for application in a membrane reactor for simultaneous production of pure hydrogen and synthesis gas,” Fuel, vol. 89, no. 6, pp. 1265–1273, 2010.
View at: Publisher Site | Google Scholar
H. J. Wei, Y. Cao, W. J. Ji, and C. T. Au, “Lattice oxygen of La_1−xSr_xMO₃ (M = Mn, Ni) and LaMnO_3−αF_β perovskite oxides for the partial oxidation of methane to synthesis gas,” Catalysis Communications, vol. 9, no. 15, pp. 2509–2514, 2008.
View at: Publisher Site | Google Scholar
V. García, M. T. Caldes, O. Joubert, E. Gautron, F. Mondragón, and A. Moreno, “Methane oxidation by lattice oxygen of Ni/BaTi_1−xIn_xO_3-δ catalysts,” Catalysis Today, vol. 157, no. 1–4, pp. 177–182, 2010.
View at: Publisher Site | Google Scholar
T. Suzuki, O. Nakayama, and N. Okamoto, “Partial oxidation of methane to nitrogen free synthesis gas using air as oxidant,” Catalysis Surveys From Asia, vol. 16, pp. 75–90, 2012.
View at: Publisher Site | Google Scholar
K. S. Cha, H. S. Kim, B. K. Yoo et al., “Reaction characteristics of two-step methane reforming over a Cu-ferrite/Ce-ZrO₂ medium,” International Journal of Hydrogen Energy, vol. 34, no. 4, pp. 1801–1808, 2009.
View at: Publisher Site | Google Scholar
K. S. Cha, B. K. Yoo, H. S. Kim et al., “A study on improving reactivity of Cu-ferrite/ZrO₂ medium for syngas and hydrogen production from two-step thermochemical methane reforming,” International Journal of Energy Research, vol. 34, no. 5, pp. 422–430, 2010.
View at: Publisher Site | Google Scholar
K. S. Go, S. R. Son, S. D. Kim, K. S. Kang, and C. S. Park, “Hydrogen production from two-step steam methane reforming in a fluidized bed reactor,” International Journal of Hydrogen Energy, vol. 34, no. 3, pp. 1301–1309, 2009.
View at: Publisher Site | Google Scholar
L. F. de Diego, M. Ortiz, F. García-Labiano, J. Adánez, A. Abad, and P. Gayán, “Synthesis gas generation by chemical-looping reforming using a Nibased oxygen carrier,” in Proceedings of the 9th International Conference on Greenhouse Gas Control Technologies (GHGT-9), vol. 1, pp. 3–10, Washington DC, USA, November 2008.
View at: Publisher Site | Google Scholar
L. F. de Diego, M. Ortiz, F. García-Labiano, J. Adánez, A. Abad, and P. Gayán, “Hydrogen production by chemical-looping reforming in a circulating fluidized bed reactor using Ni-based oxygen carriers,” Journal of Power Sources, vol. 192, no. 1, pp. 27–34, 2009.
View at: Publisher Site | Google Scholar
M. Rydén, M. Johansson, A. Lyngfelt, and T. Mattisson, “NiO supported on Mg-ZrO₂ as oxygen carrier for chemical-looping combustion and chemical-looping reforming,” Energy and Environmental Science, vol. 2, no. 9, pp. 970–981, 2009.
View at: Publisher Site | Google Scholar
M. Ortiz, L. F. de Diego, A. Abad, F. García-Labiano, P. Gayán, and J. Adánez, “Hydrogen production by auto-thermal chemical-looping reforming in a pressurized fluidized bed reactor using Ni-based oxygen carriers,” International Journal of Hydrogen Energy, vol. 35, no. 1, pp. 151–160, 2010.
View at: Publisher Site | Google Scholar
T. Pröll, J. Bolhàr-Nordenkampf, P. Kolbitsch, and H. Hofbauer, “Syngas and a separate nitrogen/argon stream via chemical looping reforming—a 140 kW pilot plant study,” Fuel, vol. 89, no. 6, pp. 1249–1256, 2010.
View at: Publisher Site | Google Scholar
M. Ryden and P. Ramos, “H₂ production with CO₂ capture by sorption enhanced chemical-looping reforming using NiO as oxygen carrier and CaO as CO₂ sorbent,” Fuel Processing Technology, vol. 96, pp. 27–36, 2012.
View at: Publisher Site | Google Scholar
M. Ortiz, L. F. de Diego, A. Abad, F. Garcia-Labiano, P. Gayan, and J. Adanez, “Catalytic activity of Ni-based oxygen-carriers for steam methane reforming in chemical-looping processes,” Energy & Fuels, vol. 26, no. 2, pp. 791–800, 2012.
View at: Publisher Site | Google Scholar
O. Nakayama, N. Ikenaga, T. Miyake, E. Yagasaki, and T. Suzuki, “Production of synthesis gas from methane using lattice oxygen of NiO-Cr₂O₃-MgO complex oxide,” Industrial and Engineering Chemistry Research, vol. 49, no. 2, pp. 526–534, 2010.
View at: Publisher Site | Google Scholar
C. Dueso, M. Ortiz, A. Abad et al., “Reduction and oxidation kinetics of nickel-based oxygen-carriers for chemical-looping combustion and chemical-looping reforming,” Chemical Engineering Journal, vol. 188, pp. 142–154, 2012.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2013 Kongzhai Li et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

8327

Downloads

4747

Citations

Journal of Chemistry

Syngas Generation from Methane Using a Chemical-Looping Concept: A Review of Oxygen Carriers

Abstract

1. Introduction

2. Chemical-Looping Concept

3. Oxygen Carriers for Chemical-Looping Selective Oxidation of Methane (CLSOM)

3.1. CeO2-Based Oxygen Carriers

3.2. Perovskite Oxygen Carriers

3.3. Other Oxygen Carriers

4. Conclusions

Acknowledgments

References

Copyright

3.1. CeO₂-Based Oxygen Carriers