Performance Comparison of Doppler Scale Estimation Methods for Underwater Acoustic OFDM

Abstract

Doppler scale estimation is one critical step needed by the resampling operation in acoustic communication receivers. In this paper, we compare different Doppler scale estimation methods using either cyclic-prefixed (CP) or zero-padded (ZP) orthogonal-frequency division-multiplexing (OFDM) waveforms. For a CP-OFDM preamble, a self-correlation method allows for blind Doppler scale estimation based on an embedded repetition structure while a cross-correlation method is available with the knowledge of the waveform. For each received ZP-OFDM block, the existence of null subcarriers allows for blind Doppler scale estimation. In addition, a pilot-aided method and a decision-aided method are applicable based on cross-correlation with templates constructed from symbols on pilot subcarriers only and from symbols on all subcarriers after data decoding, respectively. This paper carries out extensive comparisons among these methods using both simulated and real experimental data. Further, the applicabilities of these methods to distributed multiuser systems are investigated.

1. Introduction

Underwater acoustic communications and networking have been under extensive investigation in recent years [1, 2]. Considerable progress on the physical layer communication techniques has been made for both single-carrier and multicarrier communications; see, for example, [3–19]. Relative to the radio channel which has relative short delay spread and slow time variation, underwater acoustic channels typically exhibit long delay spread and fast time variation. The latter brings significant Doppler effects to underwater acoustic communication systems, hence estimation of the Doppler scaling factor is one key receiver module [4, 20, 21].

Typically, Doppler scale estimation is accomplished by inserting waveforms known to the receiver during the data transmission. Two popular approaches are described in the following.(i)One approach is to use a pulse train which is formed by the repetition of a Doppler-insensitive waveform [22], such as linear-frequency-modulated (LFM) waveform [23] and hyperbolic-frequency-modulated (HFM) waveform [24]. A transmission format with one preamble and one postamble around the data burst is usually adopted [4, 20, 25], as shown in Figure 1. At the receiver side, by detecting the times-of-arrival of the preamble and postamble, thus the interval change in-between, an average Doppler scale estimate over the whole data burst can be obtained. Thanks to the Doppler-insensitive property of the waveforms, a single-branch-matched filtering operation is adequate even in the presence of Doppler distortion. However, this method is only suitable for offline processing due to the processing delay.(ii)The other approach is to use a Doppler-sensitive waveform with a thumb-tack ambiguity function. A Doppler-sensitive waveform is usually transmitted as a preamble prior to the data burst, as shown in Figure 1. At the receiver side, a bank of correlators correlates the received signal with preambles prescaled by different Doppler scaling factors, and the branch with the largest correlation peak provides the estimated Doppler scale [25]. Typical Doppler-sensitive waveforms include Costa waveforms [26], m-sequence [27], and poly-phase sequence [28].

Figure 1 

Top: Doppler scale estimation with Doppler-insensitive waveforms. Bottom: Doppler scale estimation with Doppler-sensitive waveforms.

In this paper, we focus on an underwater acoustic communication system using zero-padded orthogonal-frequency division-multiplexing modulation (ZP-OFDM), in which pilot subcarriers and null subcarriers are usually multiplexed with data subcarriers for channel estimation and residual Doppler shift mitigation, respectively [4]. A cyclic prefixed (CP) OFDM preamble is inserted prior to data transmission for detection, synchronization, and Doppler scale estimation [29]. This transmission format, as shown in Figure 2, has been implemented on DSP-based OFDM modem prototypes [30].

Figure 2 

The data burst structure considered in this paper, which consists of a special CP-OFDM preamble and multiple ZP-OFDM blocks.

By exploiting the cyclic repetition structure of the CP-OFDM preamble, a blind estimation with a bank of self-correlators was proposed in [29]. However, it does not leverage the knowledge of the waveform itself which is known to the receiver. Taking this method as the first approach, one can easily construct the following Doppler scale estimators for the OFDM transmission in Figure 2.(i)Cross-correlation with the CP-OFDM Preamble: Given the Doppler sensitivity of the OFDM waveform, a bank of cross-correlators can use the prescaled versions of the CP-OFDM waveform as local replicas.(ii)Pilot-Aided Method for Each ZP-OFDM Block: By taking the waveform constituted by the pilot-subcarrier components as a replica of the transmitted signal, the Doppler estimation method using a bank of cross-correlators is directly applicable.(iii)Null-Subcarrier Based Blind Estimation Method for Each ZP-OFDM Block: As an extension of the blind carrier frequency offset (CFO) estimation method [31], the receiver rescales the received waveform with different tentative Doppler scaling factors and uses the energy on the null subcarriers to find the best fit.(iv)Decision-Aided Method for Each ZP-OFDM Block: Once a ZP-OFDM block is successfully decoded, the transmitted waveform corresponding to this block can be reconstructed at the receiver. Taking the reconstructed waveform as a local replica, the Doppler estimation method using a bank of correlators can be deployed to refine the Doppler scale estimation for this block. The refined Doppler scale estimate can be passed to the next block.

The contributions of this paper are the following.(i)We carry out extensive performance comparisons among the aforementioned Doppler estimation methods. Specifically, we focus on the OFDM transmission format in Figure 2 in single-user transmissions. Both simulations and experimental results reveal that the correlation-based methods have a decent performance in the low SNR region, and the blind estimation methods can catch up or even outperform the correlation methods in the high SNR region. As a performance benchmark, the Cramer-Rao lower bound (CRLB) is also included for single-path channels.(ii)We extend our investigation to a multiuser OFDM setting, where different users could have different Doppler scaling factors [32]. Simulation results show that the correlation-based methods are robust to the multiuser interference, while the blind method suffers severe performance degradation.

The rest of this paper is as follows. Different Doppler scale estimation methods for CP-OFDM and ZP-OFDM waveforms are presented in Sections 2 and 3, respectively. Simulation results of these methods are provided in Section 4, and experimental results are provided in Section 5. Extension to the multiuser scenario is described in Section 6. Conclusions are contained in Section 7.

2. Doppler Scale Estimation with a CP-OFDM Preamble

Consider a CP-OFDM preamble structure in Figure 2, which consists of two identical OFDM symbols of length 𝑇₀ and a cyclic prefix of length 𝑇_cp in front, with the embedded structure𝑥_cp(𝑡)=𝑥_cp𝑡+𝑇₀,−𝑇_cp≤𝑡≤𝑇₀.(1)

Let 𝐵 denote the system bandwidth, and define 𝐾₀∶=𝐵𝑇₀ as the number of subcarriers. The baseband CP-OFDM signal is𝑥_cp(𝑡)=^𝐾0/2−1_𝑘=_−𝐾0/2𝑑[𝑘]𝑒^{𝑗2𝜋(𝑘/2𝑇0)}𝑞(𝑡),𝑡∈−𝑇_cp,2𝑇₀,(2) where 𝑑[𝑘] is the transmitted symbol on the 𝑘th subcarrier, and 𝑞(𝑡) is a pulse shaping window,𝑞(𝑡)=1,𝑡∈−𝑇^cp0,elsewhere.,2𝑇₀.(3) The passband signal can be obtained as 𝑥̃_cp(𝑡)=2Re{𝑥_cp(𝑡)𝑒^{𝑗2𝜋𝑓c𝑡}}, where 𝑓_c is the center frequency.

Consider a multipath channel which consists of 𝑁_pa pathsℎ(𝑡;𝜏)=^𝑁pa_𝑝=1𝐴_𝑝(𝑡)𝛿𝑡−𝜏_𝑝(𝑡),(4) where 𝐴_𝑝(𝑡) and 𝜏_𝑝(𝑡) denote the amplitude and delay of the 𝑝th path, respectively. Throughout this paper, we assume that the amplitude is constant within each OFDM block (about 200 ms for the system considered in this paper), that is, 𝐴_𝑝(𝑡)≈𝐴_𝑝, which leads toℎ(𝑡;𝜏)=^𝑁pa_𝑝=1𝐴_𝑝𝛿𝑡−𝜏_𝑝(𝑡).(5)

After transmitting the passband signal 𝑥̃_cp(𝑡) through the multipath channel, the received passband signal 𝑦(̃𝑡) is converted to baseband as 𝑦(𝑡)=LPF(𝑦(̃𝑡)𝑒^{−𝑗2𝜋𝑓c𝑡}), where LPF denotes the low pass filtering operation.

2.1. Self-Correlation

If all the paths in the channel have the same Doppler scale factor𝜏_𝑝(𝑡)=𝜏_𝑝−𝑎𝑡,(6) it is shown in [29] that the embedded structure in the received waveform becomes𝑦(𝑡)=𝑒^{−𝑗2𝜋(𝑎/(1+𝑎))𝑓c𝑇0}𝑦𝑡+𝑇⁰−𝑇1+𝑎_cp,−𝜏_max1+𝑎≤𝑡≤1𝑇+⁰𝑎,(7) which has a repetition period 𝑇₀/(1+𝑎) regardless of the channel amplitudes.

By exploiting the structure in (7), the time-of-arrival and the Doppler scale of the CP-OFDM symbol in the received signal can be jointly estimated via(𝑎,̂𝜏̂)=argmax_𝑎,𝜏||||^𝑇₀^0/(1+𝑎)𝑦(𝑡+𝜏)𝑦^∗𝑡+𝜏+1𝑇+⁰𝑎𝑑𝑡||||,(8) which does not require the knowledge of the channel and the data symbols. This method can be implemented with a bank of self-correlators [29].

2.2. Cross-Correlation

Rather than exploiting the structure of the CP-OFDM preamble, the cross-correlation-based method can be used, since the transmitted preamble is known at the receiver. Taking the basic unit of duration 𝑇₀ as the template, the joint time-of-arrival and Doppler rate estimation can be achieved via(𝑎,̂𝜏̂)=argmax_𝑎,𝜏||||^𝑇₀₀𝑦(𝑡+𝜏)𝑥^∗_cp((1+𝑎)𝑡)𝑒^{−𝑗2𝜋𝑎𝑓c𝑡}𝑑𝑡||||.(9) This can be implemented via a bank of cross-correlators, where the branch yielding the largest peak provides the needed Doppler scale estimate.

3. Doppler Scale Estimation with Each ZP-OFDM Block

As described in [4], a ZP-OFDM signal design multiplexing pilot and null subcarriers with data subcarriers can effectively deal with fast channel variations. Assume that the ZP-OFDM system has 𝐾 subcarriers. Let 𝑇 denote the symbol duration and 𝑇_g the guard interval. The total OFDM block duration is thus 𝑇_bl∶=𝑇+𝑇_g. Denote 𝒮_D, 𝒮_P, 𝒮_N as the nonoverlapped sets formed by the data subcarriers, pilot subcarriers, and null subcarriers, respectively, which satisfy 𝒮_D⋃𝒮_P⋃𝒮_N={−𝐾/2,…,𝐾/2−1}. The baseband transmitted ZP-OFDM signal can be expressed by𝑥_zp(𝑡)=_{𝑘∈𝒮D⋃𝒮P}𝑑[𝑘]𝑒^{𝑗2𝜋(𝑘/𝑇)𝑡}𝑔(𝑡),𝑡∈0,𝑇_bl,(10) where 𝑔(𝑡) describes the zero-padding operation, that is,𝑔(𝑡)=10,,𝑡el∈sew[0h,e𝑇re].,(11)

After transmitting the ZP-OFDM symbol through a multipath channel defined in (5), we denote 𝑦(̃𝑡) as the received passband signal, whose baseband version is 𝑦(𝑡)=LPF(𝑦(̃𝑡)𝑒^{−𝑗2𝜋𝑓c𝑡}). The availability of null subcarriers, pilot subcarriers, and data subcarriers can be used for Doppler scale estimation.

3.1. Null-Subcarrier-Based Blind Estimation

In [29], the null subcarriers in ZP-OFDM system are exploited to perform carrier frequency offset (CFO) estimation. Here in this paper, the same principle is used to estimate Doppler scale factor.

Assume that coarse synchronization is available from the preamble. After truncating each ZP-OFDM block from the received signal, we resample one block with different tentative scaling factors. The total energy of frequency measurements at null subcarriers are used as a metric for the Doppler scale estimation𝑎̂=argmin_𝑎𝑘_∈𝒮N||||^𝑇+𝑇_g0𝑦𝑡1+𝑎𝑒^{−𝑗2𝜋𝑎𝑓c𝑡}𝑒^{−𝑗2𝜋(𝑘/𝑇)𝑡}𝑑𝑡||||².(12) For each tentative 𝑎, a resampling operation is carried out followed by fast Fourier transform. A one-dimensional grid search leads to a Doppler scale estimate.

3.2. Pilot-Aided Estimation

As introduced above, a set of subcarriers 𝒮_P is dedicated to transmit pilot symbols. Hence, the transmitted waveform 𝑥_zp(𝑡) is partially known, containing𝑥_pilot(𝑡)=_𝑘∈𝒮P𝑑[𝑘]𝑒^{𝑗2𝜋(𝑘/𝑇)𝑡}𝑔(𝑡),𝑡∈[0,𝑇].(13)

The joint time-of-arrival and Doppler scale estimation is achieved via(=𝑎,̂a𝜏r̂)gmax_𝑎,𝜏||||^{0𝑇/(1+𝑎)}𝑦(𝑡+𝜏)𝑥^∗_pilot((1+𝑎)𝑡−𝜏)𝑒^{−𝑗2𝜋𝑎𝑓c𝑡}𝑑𝑡||||,(14) which can be implemented via a bank of cross-correlators.

3.3. Decision-Aided Estimation

For an OFDM transmission with multiple blocks, the Doppler estimated in one block can be used for the resampling operation of the next block assuming small Doppler variation across blocks. After the decoding operation the receiver can reconstruct the transmitted time-domain waveform, by replacing 𝑑[𝑘] by its estimate 𝑑[𝑘], for all 𝑘∈𝒮_D in. Denote the reconstructed waveform as 𝑥̂_zp(𝑡).

Similar to the pilot-aided method, the decision-aided method performs the joint time-of-arrival and Doppler scale estimation via(=𝑎,̂a𝜏r̂)gmax_𝑎,𝜏||||^{0𝑇/(1+𝑎)}𝑦(𝑡+𝜏)𝑥̂^∗_zp((1+𝑎)𝑡−𝜏)𝑒^{−𝑗2𝜋𝑎𝑓c𝑡}𝑑𝑡||||,(15) which again is implemented via a bank of cross-correlators. The estimated 𝑎̂ can be used for the resampling operation of the next block.

Remark 1. Relative to the pilot-aided method, the decision-aided method leverages the estimated information symbols, thus is expected to achieve a better estimation performance. Assuming that all the information symbols have been successfully decoded, the decision-aided method has knowledge about both the data and pilot symbols. Let |𝒮_P| and |𝒮_D| denote the numbers of pilot and data symbols, respectively. Using the template 𝑥̂_zp(𝑡) constructed from (|𝒮_P|+|𝒮_D|) known symbols for cross correlation achieve a 10log₁₀((|𝒮_P|+|𝒮_D|)/|𝒮_P|) dB power gain in terms of noise reduction, relative to that using the template 𝑥_pilot(𝑡) constructed from |𝒮_P| known symbols.

4. Simulation Results

The OFDM parameters are summarized in Table 1. For CP-OFDM, the data symbols at all the 512 subcarriers are randomly drawn from a QPSK constellation. For ZP-OFDM, out of 1024 subcarriers, there are |𝒮_N|=96 null subcarriers with 24 on each edge of the signal band for band protection and 48 evenly distributed in the middle for the carrier frequency offset estimation; |𝒮_P|=256 are pilot subcarriers uniformly distributed among the 1024 subcarriers, and the remaining are |𝒮_D|=672 data subcarriers for delivering information symbols. The pilot symbols are drawn randomly from a QPSK constellation. The data symbols are encoded with a rate-1/2 nonbinary LDPC code [33] and modulated by a QPSK constellation.

Table 1 

OFDM parameters in simulations.

Three UWA channel settings are tested.(i)Channel Setting 1: A single-path channel: ℎ(𝑡,𝜏)=𝛿(𝑡−[𝜏−𝑎𝑡]).(16)(ii)Channel Setting 2: A multipath channel with 𝑁_pa=15 paths, where all paths have one common Doppler scaling factor: ℎ(𝑡,𝜏)=^𝑁pa_𝑝=1𝐴_𝑝𝛿𝑡−𝜏_𝑝−𝑎𝑡.(17)(iii)Channel Setting 3: A multipath channel with 𝑁_pa=15 paths, where each path has an individual Doppler scaling factor: ℎ(𝑡,𝜏)=^𝑁pa_𝑝=1𝐴_𝑝𝛿𝑡−𝜏_𝑝−𝑎_𝑝𝑡.(18)

The interarrival time of paths follows an exponential distribution with a mean of 1 ms. The mean delay spread for the channels in and is thus 15 ms. The amplitudes of paths are Rayleigh distributed with the average power decreasing exponentially with the delay, where the difference between the beginning and the end of the guard time is 20dB. For each path, the Doppler scale 𝑎_𝑝 is generated from a Doppler speed 𝑣_𝑝 (with unit m/s):𝑎_𝑝=𝑣^𝑝𝑐,(19) where 𝑐=1500m/s is the sound speed in water. In channel settings 1 and 2, the Doppler speed 𝑣 is uniformly distributed within [−4.5,4.5] m/s. In channel setting 3, the Doppler speeds {𝑣_𝑝} are randomly drawn from the interval [1.5−0.1,1.5+0.1] m/s.

In channel settings 1 and 2, the ground truths of 𝑣 and 𝑎 are known. We adopt the root-mean-squared-error (RMSE) of the estimated Doppler speed as the performance metric,RMSE=𝐸||𝑣̂−𝑣||²=𝐸||(𝑎̂−𝑎)𝑐||²,(20) which has the unit m/s. In channel setting 3, different paths have different Doppler scales, while the Doppler scale estimator only provides one estimate. RMSE is hence not well motivated. With the estimated Doppler scale to perform the resampling operation, we will use the block-error-rate (BLER) of the ZP-OFDM decoding as the performance metric.

4.1. RMSE Performance with CP-OFDM

For the single-path channel, Figure 3 shows the RMSE performance of two estimation methods at different SNR levels. One can see a considerable gap between the self-correlation method and the cross-correlation method, while in the medium to high SNR region, both methods can provide a reasonable performance to facilitate receiver decoding.

Figure 3 

Performance of different estimators for the CP-OFDM preamble in single-path and multipath channels (channel settings 1 and 2).

For the multipath channel with a single Doppler speed, Figure 3 shows the RMSE performance of two estimation methods. One can see that the cross-correlation method outperforms the self-correlation method considerably in the low SNR region. However, the former suffers an error floor in the high SNR region, while the later does not.

Relative to the RMSE performance in the single-path channel, a considerable performance degradation can be observed for the cross-correlation method in the multipath channel, whereas the performance of the self-correlation method is quite robust. The reason for the difference lies in the capability of the self-correlation method to collect the energy from all paths for Doppler scale estimation, while the cross-correlation method aims to get the Doppler scale estimate from only one path, the strongest path.

4.2. RMSE Performance with ZP-OFDM

Figure 4 shows the RMSE performance of three estimation methods for ZP-OFDM in single-path channels. In the low SNR region, one can see that the decision-aided method is the best, while the null-subcarrier-based blind method is the worst. As discussed in Remark 1, the decision-aided method achieves 10log₁₀((|𝒮_D|+|𝒮_P|)/|𝒮_P|)≈6dB power gain relative to the pilot-aided method. In the medium and high SNR region, the pilot-aided method suffers an error floor due to the interference from the data subcarriers, and the null-subcarrier-based blind method gets a good estimation performance. The Cramer-Rao lower bound (CRLB) with a known waveform is also included as the performance benchmark, whose derivation can be carried out similar to [34, 35].

Figure 4 

Performance of different estimators for ZP-OFDM in single-path channels (channel setting 1). The CRLB with all data known is included as a benchmark.

Figure 5 shows the RMSE performance of three methods in multipath channels with a common Doppler speed. For each realization, the Doppler scale, the path amplitudes, and delays are randomly generated. The RMSE corresponding to each method is calculated by averaging the estimation error over multiple realizations. Again, one can see that in the low SNR region, the decision-aided method has the best performance, while the null-subcarrier-based blind method is the worst. Different from the performance in the single-path channel, the decision-aided method has an error floor in the high SNR region, since it only picks up the maximum correlation peak of one path. On the other hand, the null-subcarrier method has robust performance in the presence of multiple paths.

Figure 5 

Performance of different estimators for ZP-OFDM in multipath channels with a common Doppler scale (channel setting 2).

4.3. Comparison of Blind Methods of CP- and ZP-OFDM

The self-correlation method for the CP-OFDM preamble is closely related to the null-subcarrier-based blind method for ZP-OFDM. This can be easily verified by rewriting (2) as𝑥_cp(𝑡)=^𝐾0−1_𝑘=_−𝐾0𝑑^[𝑘]𝑒^{𝑗2𝜋(𝑘/(2𝑇0))𝑡}𝑞(𝑡),𝑡∈−𝑇_cp,2𝑇₀,(21) where 𝑑′[𝑘]=0 when 𝑘 is odd and 𝑑′[𝑘]=𝑑[𝑘/2] when 𝑘 is even. The cyclic repetition pattern in is generated by placing zeros on all odd subcarriers in a long OFDM symbol of duration 2𝑇₀. Hence, the self-correlation implementation could be replaced by the null-subcarrier-based implementation for the CP-OFDM preamble.

Figure 6 shows the performance comparison between the blind method for ZP-OFDM and that for CP-OFDM in the multipath channel with one Doppler scale factor, respectively. At low SNR, typically when it’s lower than 0 dB, the null-subcarrier-based method in CP-OFDM system has a better performance than that in the ZP-OFDM system, which is due to the fact that CP-OFDM system has 512 null subcarriers, more than 96 null subcarriers in the ZP-OFDM block. At high SNR, the null-subcarrier-based method in ZP-OFDM has better performance. The possible reason is that null subcarriers in ZP-OFDM are distributed with an irregular pattern, which could outperform the regular pattern in the CP-OFDM preamble.

Figure 6 

Null-subcarrier-based method in ZP-OFDM and CP-OFDM.

4.4. BLER Performance with ZP-OFDM

With channels generated according to the channel setting 3, Figure 7 shows the simulated BLER performance, where the received OFDM blocks are resampled with the Doppler scale estimates from different estimators and processed using the receiver from [4] and the LDPC decoder from [33]. At each SNR point, at least 20 block errors are collected.

Figure 7 

The BLER performance in multipath multi-Doppler channels (channel setting 3).

It is expected that the OFDM system can only work when the useful signal power is above that of the ambient noise. Regarding the simulation results in Figure 5, one can see that all the methods can reach a RMSE lower than 0.1 m/s. Hence, it is not surprising that these methods lead to quite similar BLER results as shown in Figure 7. This observation is consistent with the analysis in [29] that an estimation error of 0.1 m/s introduces a negligible error.

5. Experimental Results

This mobile acoustic communication experiment (MACE10) was carried out off the coast of Martha’s Vineyard, Massachusetts, June, 2010. The water depth was about 80 meters. The receiving array was stationary, while the source was towed slowly away from the receiver and then towed back, at a speed around 1 m/s. The relative distance of the transmitter and the receiver changed from 500 m to 4.5 km. Out of the two tows in this experiment, we only consider the data collected in the first tow. There are 31 transmissions in total, with a CP-OFDM preamble and 20 ZP-OFDM blocks in each transmission. We exclude one transmission file recorded during the turn of the source, where the SNR of the received signal is quite low.

The CP-OFDM and ZP-OFDM parameters and signal structures are identical to that in the simulation, as listed in Table 1.

Figure 8 shows the estimated Doppler speeds for ZP-OFDM blocks from different methods. Clearly, the Doppler speed fluctuates from block to block. Figure 9 shows the estimated channel impulse responses for two ZP-OFDM blocks from two data sets, where the time interval between these two data bursts is more than 1 hour. The channels have a delay spread about 20 ms but with different delay profiles.

Figure 8 

MACE10: Estimated Doppler speeds for 30 data bursts in MACE10, where each data burst has 20 OFDM blocks. The time interval between two consecutive date bursts is around 4 mins.

(a) File ID: 1750155F1978_C0_S5

(b) File ID: 1750155F2070_C0_S5

Figure 9 

Estimated channel impulse responses for two different blocks at different bursts.

Based on the recorded files, we carried out two tests.

(A) Test Case 1
In this test, we focus on one single file (file ID: 1750155𝐹1954_C0_S5) and compare the RMSE performance of different approaches by adding artificial noise to the recorded signal. The ground truth of the Doppler scale factor is not available. When computing the RMSE using (20) for each method, we use the estimated Doppler scale of the original file without adding the noise as the ground truth. Figure 10 shows the estimation performance of several approaches. Similar observations as the simulation results in Figures 3 and 5 are found.

Figure 10 

MACE10: Performance comparison of Doppler estimation approaches, file ID: 1750155F1954_C0_S5.

(B) Test Case 2
In this test, we compare the BLER performance of an OFDM receiver where the resampling operation is carried out with different Doppler scale estimates from different methods.
Due to the relatively high SNR of the recorded signal, we create a semiexperimental data set by adding white Gaussian noise to the received signal. Define 𝜎² as the estimated ambient noise power in the original recorded signal. Figure 11 shows the BLER performance with different Doppler estimation approaches by adding different amount of noises to the received files.
One can see that the methods for ZP-OFDM outperform the methods for CP-OFDM, as the Doppler scale itself is continuously changing from block to block, as illustrated in Figure 8. Another interesting observation is that the null-subcarrier-based blind method has slight performance improvement relative to the pilot- and decision-aided methods. This agrees with the simulation results in Figure 5 that in the high SNR region, the blind estimation method does not suffer an error floor in the multipath channel, hence enjoys a better estimation performance.

(a) Adding noise with power 𝜎2

(b) Added noise with power 2𝜎2

Figure 11 

MACE10: BLER Performance using different Doppler estimation methods by adding artificial noise to the received signal, 𝜎2 denoting the estimated ambient noise power.

6. Extension to Distributed MIMO-OFDM

If the transmitters in a multi-input multi-output (MIMO) system are co-located, the Doppler scales corresponding to all transmitters are similar, and hence a single-user blind Doppler scale estimation method would work well, as done in [10]. However, if the transmitters are distributed, for example in a system with multiple single-transmitter users, the Doppler scales for different users could be quite different, even with opposite signs [32]. We now investigate the performance of different Doppler scale estimation methods in the presence of multiuser interference. We will use the ZP-OFDM waveform as the reference design; similar conclusions can be applied to the CP-OFDM preamble. Only simulated data sets are used in the following tests.

6.1. Pilot- and Decision-Aided Estimation

We simulate a two-user system. Each user generates a multipath channel according to channel setting 2 independently. The positions of pilot, null, and data subcarriers are the same for different users. The pilot and data symbols of different users are randomly generated and hence are different.

Figure 12 depicts the RMSE performance of the pilot- and decision-aided estimation methods. Compared with the performance in the single-user setting in Figure 5, there is performance degradation and the error floors are higher. However, both methods can achieve RMSE lower than 0.1 m/s at low SNR values. Hence, both methods have robust performance in the presence of multiuser interference.

Figure 12 

Pilot- and decision-aided Doppler scale estimation in a distributed two-user ZP-OFDM system.

6.2. Null-Subcarrier-Based Blind Estimation

The null-subcarrier-based blind estimation method exploits the transmitted OFDM signal structure. Since all the users share the same positions of null subcarriers, there is a user-association problem even when multiple local minimums are found. We simulate a two-user system where the Doppler speeds of user 1 and user 2 are uniformly distributed within [−4.5,−0.5] m/s and [0.5,4.5] m/s, respectively. Without adding the ambient noise to the received signal, Figure 13 demonstrates both successful and failed cases using the objective function in (12). The objective functions in the single-user settings are also included for comparison. One can see that the multiuser interference degrades the estimation performance significantly. Hence, although the blind method developed for the single user case can be used to colocated MIMO-OFDM as in [10], it is not applicable to distributed MIMO-OFDM where different users have different Doppler scales.

(a) Successful case

(b) Failed case

Figure 13 

Illustration of the objective functions of the null-subcarrier-based method in a two-user system

7. Conclusion

This paper compared different methods for Doppler scale estimation for a CP-OFDM preamble followed by ZP-OFDM data transmissions. Blind methods utilizing the underlying signalling structure work very well at medium to high SNR ranges, while cross-correlation-based methods can work at low SNR ranges based on the full or partial knowledge of the transmitted waveform. All of these methods are viable choices for practical OFDM receivers. In a distributed multiuser scenario, cross-correlation approaches are more robust against multiuser interference than blind methods.

Acknowledgments

This work is supported by the ONR Grant N00014-09-1-0704 (PECASE) and the NSF Grant ECCS-1128581. The authors thank Dr. Lee Freitag and his team for conducting the MACE10 experiment.