Abstract

To develop a detailed reaction mechanism for plasma-assisted methane steam reforming, a comprehensive numerical and experimental study of effect laws on methane conversion and products yield is performed at different steam to methane molar ratio (S/C), residence time s, and reaction temperatures. A CHEMKIN-PRO software with sensitivity analysis module and path flux analysis module was used for simulations. A set of comparisons show that the developed reaction mechanism can accurately predict methane conversion and the trend of products yield in different operating conditions. Using the developed reaction mechanism in plasma-assisted kinetic model, the reaction path flux analysis was carried out. The result shows that CH3 recombination is the limiting reaction for CO production and O is the critical species for CO production. Adding 40 wt.% Ni/SiO2 in discharge region has significantly promoted the yield of H2, CO, or CO2 in dielectric packed bed (DPB) reactor. Plasma catalytic hybrid reforming experiment verifies the reaction path flux analysis tentatively.

1. Introduction

Chemically recuperated gas turbines (CRGT) are regarded as prospective advanced cycle engines due to high thermal efficiencies and low emissions. Steam reformer as the kernel component of CRGT can deeply recover turbine exhaust heat by fuel steam reforming. Traditional steam reforming process occurs in the conditions of high temperature (700–900°C) and high pressure (2-3 MPa). However, turbine exhaust temperature is only in the range of 350 to 500°C. Considering that plasma is a prospective tool without restriction from reaction temperature, nonequilibrium plasma-assisted fuel steam reforming technology for recycling exhaust heat in CRGT has been proposed. Because of the nonequilibrium characteristic of plasma, methane was converted into high hydrocarbons or synthesis gas in plasma-assisted steam reforming process. To seek the way to improve objective products yield, experimental and numerical researches on reforming process and reaction mechanism are necessary.

Recently, scholars researched plasma-assisted reforming mechanism by experiment and numerical simulation. In numerical researches, Rusu and Cormier [1] studied MSR in gliding arc reactor by thermodynamical equilibrium model; Petrovi et al. [2] studied the influence of gas flow rate and reactor geometry and applied voltage parameters on the discharge characteristics by fluid model but did not consider free radical reactions; Nair et al. [3] investigated plasma-assisted methane conversion in gas phase by partial oxidation at low energy density (80–200 kJ/mol CH4) and low reactor temperatures (130–140°C) by constants substitution method; Li et al. [4] carried out kinetic simulation for methane coupled reaction based on Townsend ionization model; de Bie et al. [5] studied the conversion of methane to higher hydrocarbons or oxygenates by partial oxidation with CO2 or O2 in a dielectric barrier discharge by fluid model in Plasimo software. These researches mainly aimed at plasma-assisted methane coupling reactions, partial oxidation, and CO2 reforming reactions and poorly referred to reaction mechanisms and kinetic effects for plasma-assisted methane steam reforming (MSR).

In experimental researches, there mainly existed two ways: one was to study the presence of dominating radicals by spectrograph [6, 7] and another was to conjecture some possible reaction pathways according to products [812]. However, they did not give out systematic reaction pathways for plasma-assisted reforming. What is more, recent studies of plasma-assisted MSR were carried out at water bath temperatures with low steam flow rates [10, 13]. So the study on plasma-assisted methane steam reforming in high flow rate of steam is very necessary.

In this paper, firstly, we study the effect laws of operating conditions on methane conversion and products yield to provide data support for reaction mechanism. Secondly, we develop a complete mechanism in order to estimate the real perspectives of MSR in plasma field and correct and hopefully perfect the mechanism further against sensitivity analysis module and experimental results. Thirdly, by employing the kinetic model and path flux analysis module, the kinetic effects of nonequilibrium plasma-assisted MSR on methane conversion are studied at 350–500°C without catalyst. At last, in order to preliminarily verify the validity of the reaction path flux analysis, plasma catalytic hybrid reforming experiment is employed.

2. Experimental Setup

Experimental setups are illustrated in Figure 1. The reactants were methane and steam; 10 vol% nitrogen was added to the methane cylinder as a reference for the quantitative analysis of the reformed gas after completion of the reaction. The flow rate of methane and nitrogen was controlled with mass flow controller (Brooks 5850E) and a tranquil flow pump was used to inject water (Beijing Xingda Co., 2PB00C). The feed gas flowed into DBD reactor after mixing. The DBD reactor employed quartz glass tube as dielectric and had a discharge gap of 1 mm and length of 130 mm and thus a total reactor volume of 12 cm3, as seen in Figure 1(c). The reactor was heated by a ceramic heating pipe and the reaction temperature was controlled through the temperature controller. Due to thermal inertia, the measured values were deviated from the set point of about 5°C. The reactor was energized by an AC high discharge voltage 4 kV at a frequency of 41.93 kHz with a power equivalent of 70.13 W. To verify the running stability, the voltage and current values were recorded at the beginning and end of each experiment. The qualitative and quantitative analyses for products were conducted online using gas chromatography (Agilent GC 7890A). GC-FID (2 m DB-1 Column + 25 m HP-Al/S Column), GC-TCD B (Hayesep Q Column + Molecular Sieve 5 Å Column), and GC-TCD C (Hayesep Q Column + Molecular Sieve 5 Å Column) were used to determine the concentration of hydrocarbons, CO/CO2/N2, and H2, respectively. Before flowing into gas chromatograph, the products were cooled by a cold trap and dried by allochroic silica gel. In order to ensure the accuracy of the measured data, the data were recorded after stabilizing the reforming system in any setting state for 20 min.

Experiments were carried out in different S/C, reaction temperatures, and residence time s with a pressure of 0.12 MPa. The standard conditions were a mass flow rate of 7.7 × 10−6 kg/s, reaction temperature of 400°C, plasma power, and frequencies of 70.13 W and 41.93 kHz, and S/C of 2. Experimental variations in different conditions are shown in Table 1, where three different mass flow rates are corresponding to residence time of 0.58, 0.39, and 0.29 s, respectively.

3. Plasma-Reforming Kinetic Model

In order to further study gas-phase process and to have more insight into the chemical mechanism, a simple kinetic model has proven to be a useful technique. The numerical simulation was done with the assumption that radicals once produced were uniformly distributed within the whole volume, that is, a zero-dimensional model. The plasma-assisted steam reforming model incorporates a set of mass conservation and gas-phase species equations as well as electron energy equation. Based on the characteristic of plasma-assisted MSR, gas temperature of the mixture was fixed in the set value. They were solved by CHEMKIN-PRO software [14]. The conservation equations are as follows:

global mass balance equation:

species conservation equation:

state equation:

and electron energy equation:

Here and refer to the collision energy lost by the electrons both from elastic, momentum-transfer collisions and from inelastic collisional processes. The plasma-reactor model calculates the momentum-transfer collision frequencies from momentum-transfer collision cross-sections. represents the summation of electron energy loss per electron-impact reactions. represents the power deposited through Joule heating into the plasma by acceleration of charged species along electric fields, namely, the effective input power. Consider the following:

chemical reaction progress equation:

chemical reaction rate equation:

Arrhenius coefficients of electron-impact reactions:

Arrhenius rate coefficients of free radical reactions:

4. Results and Discussion

4.1. Experimental Process Analysis

In order to observe discharge phenomenon conveniently to confirm normal discharge and furthermore to determine the structure of DPB reactor, this paper designed a visual reactor, using salt solution with a mass concentration of 20% as outer electrode, which meant the dielectric was put close to outer electrode, as seen in Figure 2. The discharge region was annular with reaction section length of 65 mm. The inner electrode was stainless steel with an outer diameter of 14 mm and 5 mm separately leading to a discharge gap of 1 mm and 5.5 mm. For the discharge gap of 1 mm, the reactor served as DBD reactor. For the discharge gap of 5.5 mm, filled in with catalyst, the reactor served as DPB reactor. Catalysts used were commercial 40 wt.% Ni/SiO2, with the column size of Φ2.5 mm × 2.5 mm (Shandong Qilu Keli Chemical Institute Co., Ltd.).

Firstly, the visual reactor was employed to observe normal discharge process. When the voltage regulator supplied a voltage of about 30 V and a current of about 0.5 A, the discharge region began to present random microdischarge with purple light. With the increase of voltage, discharge filaments were gradually thickened and then full of the annular discharge region, as seen in Figure 2.

In DPB reactor, 40 wt.% Ni/SiO2 catalyst pellets were placed in the discharge region and contacted inner electrode. After plasma source was on, discharge was nonuniform. The important find was that hot spots (orange light) emerged in the contact area between catalyst and inner electrode, while normal discharge filaments (purple light) still emerged in the contact area between catalyst and dielectric, as shown in Figure 3. The reason might be that 40 wt.% Ni/SiO2 catalyst pellets became a part of metallic inner electrode, and discharge current flowed through pellet contacts where catalysts were contacted point-to-point, leading to extremely large current density, and then hot spots were produced. However, the hot spots were not expected in DPB reactor, since it would cause a lot of energy consumption. Thus, to avoid hot spots, the structure of reactor was improved by employing double-dielectric structure in the design, as seen in Figure 4, and it was verified that no hot spot appeared.

The performance of reactor was evaluated by methane conversion, products yields, and effective carbon recovery rate. The conversion and yield are defined as follows:

Because of nonequilibrium characteristic of plasma, plasma-assisted methane steam reforming process may produce hydrocarbons C2, C3, C4, and C5 by type of adiabatic or even exothermic reaction process, which is not conducive to recycling exhaust heat. High hydrocarbons are not conducive to combustion efficiency or the lean-blowout performance of the combustor. Based on these reasons, we propose the concept of effective carbon recovery rate to represent the recuperation and combustion characteristics, as seen in

4.2. Development of Reaction Mechanism

According to the theory of low temperature plasma chemistry, nonequilibrium plasma-assisted reforming process mainly includes electron-impact reactions and free radical reactions. High energy electrons (1 eV < Te < 10 eV) impact CH4 and H2O molecules to generate vibrationally excited species, radicals, ions, and electron by excitation, dissociation, and ionization. Radicals generated from electron-impact reactions had predominance in methane conversion, while ions had little effect on reforming process [15]. According to experimental results, C2, C3, C4, C5, and C were also included in calculation model. However, in order not to further complicate our plasma reaction mechanism, the higher hydrocarbons (C4 and C5) were only treated by two chemical reactions, and some adjustments were made to their Arrhenius coefficients to ensure the agreement between calculation and experimental results.

The effective collisions of electrons in plasma-assisted reforming process occurred only in the group of energetic electrons with a certain probability. This paper took all the electrons with global mean electron energy to substitute for the partial energetic electrons and then established the relationship between rate coefficients of electron-impact reactions and mean electron energy; that is, . This dependence was calculated by BOLSIG+ Boltzmann solver [16] based on electron collision cross-section data [17]. Then by means of fitting procedure ORIGIN Arrhenius coefficients of electron-impact reactions were obtained, where electron E was treated just like any other species [14]. The Arrhenius rate coefficients of radical reactions were inquired by NIST Chemistry WebBook [18]. The development diagram of reaction mechanism is shown in Figure 5.

During the development of reaction mechanism, a group of experimental results were chosen as comparison, with the operating conditions of a pressure of 0.12 MPa, reaction temperature of 400°C, total flow of inlet reactants of 7.7 × 10−6 kg/s, S/C of 2, and the input power of 70.13 W. Since the plasma-assisted model was zero-dimensional, it did not solve the Poisson equation for the electric field and therefore did not take into account charge separation and sheath formation near the electrode. Moreover, there were polarization losses as well as ohmic losses in quartz materials. However, it is notable that the research object for kinetic model is gas, not including reactor itself; namely, the input power here totally acts on gas, not on dielectric loss. To distinguish from the input power setting in the experimental operating conditions, a new term “effective input power” for gas in kinetic model was defined. So in the present work, the effective input power was considered to be an adjustable parameter and varied until methane conversion at reactor outlet was close to experimental results. Once the effective input power was selected, it remained unchanged in the next study to avoid the influence of input power on methane conversion and products yield. At last, the effective input power was selected to fixed value of 56 W and, correspondingly, the calculation conditions used in the model are shown in Table 2.

At last, according to correlative references and experimental results, after correcting and perfecting against the sensitivity analysis module, a total of 175 reactions with 39 species were given out for plasma-assisted MSR (as seen in Appendices A and B in supporting information in the Supplementary Material available online at http://dx.doi.org/10.1155/2014/938618).Molecular species: E CH4 H2O H2 CO2 CO C2H6 C2H4 C2H2 CH3OH CH3O CH2O C3H8 C3H6 C4H10 C5H12.Radical species: CH3 CH2 CH C C2H5 C2H3 C2H HCO OH H O I*C3H7 N*C3H7 C4H9.Ionic species: CH4+ CH3+ H− CH2− OH− O− CH2+ CH+ C+.

4.3. Validation of Plasma-Reforming Kinetic Model

The dependence of methane conversion and products yield on the S/C, reaction temperature, and residence time is shown in Figure 6. In order to validate the plasma-assisted MSR kinetic model, the predicted values in different conditions are also plotted in Figure 6. The model can accurately predict methane conversion and the trend of products yield in different operating conditions, where deviation of C2H6 predicted and experimental values ​​is within 4%. But the kinetic model overpredicted H2 (up to 18%–40%) and underpredicted CO (up to 60%–80%) and C3H8 (up to 20%–50%) by volume. During the experiment slightly yellow oil droplets with a pungent odor flowed out with the condensing water, which were higher hydrocarbons liquefied into oil droplets in the cold trap. It proved that part of methane was converted into higher hydrocarbons (C4 and C5). However, in the present model, higher hydrocarbons were only treated by two reactions. Thus underestimation of higher hydrocarbons was probably leading to the obvious overestimation of H2 selectivity in our model. As seen in Figure 8 the dominant formation paths for H2 were through H abstraction reactions with CH4, C2H6, C3H8, , and , and similar results were reported by Sun et al. [19].

4.4. Kinetic Analysis

As shown in Figure 6(a), with the increase of S/C, CH4 conversion and yields of H2 and CO increased. The thing which needed to be firstly declared was that the increase of S/C in the experiment meant that methane content in reactants correspondingly decreased in order to ensure residence time in discharge region constant. As shown in Figure 7(a), our simulations pointed out that reactions (R130), (R129), (R3), and (R37) were responsible for the production and consumption of CH4, where OH and H used in reaction (R130) and (R129) were mainly from electron-impact H2O dissociation reaction (R12), as seen in Figure 7(b). Figure 8(a) shows the effect of S/C on the consumption rate of the above reactions. With increasing S/C, consumption rate of H2O in reaction (R12) monotonously increased, while consumption rate of CH4 in reaction (R3) slightly decreased. Although CH4 content decreased with increasing S/C, consumption rate of CH4 in reaction (R129) and reaction (R130) remained unchanged due to the increase of OH and H concentration. Figure 8(a) also shows total consumption rate and relative consumption rate of CH4. Total consumption rate of CH4 decreased with S/C, which was consistent with the result of Sugasawa et al. [11]. However, due to the decrease of methane content in reactants, the relative consumption rate of CH4 had a significant increase, resulting in an improvement of methane conversion.

Figure 6(b) shows the influence of reaction temperature on methane conversion and products yield. In numerical simulation, when the effective input power was set in the fixed value of 56 W, methane conversion increased linearly. According to Figure 8(b), temperature had almost no effect on electron-impact dissociation reaction (R3) and (R12), while reaction (R129) was enhanced and total consumption rate of CH4 increased with temperature increasing. However, experimental results at different reaction temperatures showed that methane conversion presented an increase first and then a decrease with temperature increasing. This might be because polarization losses as well as ohmic losses of quartz materials increased for orders of magnitude due to ionic conductivity when the temperature increased, and thus the power deposition on reactants decreased when input power was constant [20]. So in the numerical study, some adjustments were made for the effective input power, with the value of 56 W into 52 W or 48 W corresponding to reaction temperature of 450°C or 500°C, respectively. After modifying the effective input power accordingly, methane conversion in simulation was in good agreement with the experimental values, that is, the dash line in Figure 6(b), which also implied and proved the effect of temperature on property of quartz materials.

Figure 6(c) shows that methane conversion and products yield significantly increased with an increase of residence time. Since the effective input power was constant, the number of energetic electron and electron energy remained unchanged. The longer the residence time was, the higher the probability of electron-impact CH4 was, which resulted in more chance for CH4 molecule to be activated. Moreover, as the residence time increased, C2 and C3 generated were further dehydrogenated to couple, which is another reason for the improvement of methane conversion. The yield of higher hydrocarbons under different residence time s is shown in Table 3.

4.5. Reaction Path Flux Analysis

In order to identify the reactions which could affect the selectivity of products in plasma-assisted methane steam reforming process, path flux analysis was performed in the condition of a pressure of 0.12 MPa, reaction temperature of 400°C, total flow of inlet reactants of 7.7 × 10−6 kg/s, S/C of 2, and input power of 70.13 W, as shown in Figure 9. CH3 was dissociated from methane mainly by H abstraction with OH and H produced via plasma discharge. Methane was also decomposed into CH3 and CH2 via electron collisions. Known from experimental results, CO yield was low, only 1%, and light hydrocarbons (C2 and C3) yield was at around 4%. This can be explained by Figure 9. It shows that 60% CH3 were recombined into C2H6 and furthermore into higher hydrocarbons by dehydrogenation coupling, while only 1.1% CH3 was combined with O and through a series of reaction pathways CH3 + O→CH2O→HCO→CO finally converted into CO.

According to (14) and (15), the reaction of methane converted to synthesis gas was strongly endothermic reaction, and the coupling reaction of methane converted to hydrocarbons was weakly endothermic reaction which was not beneficial for waste heat recovery. Therefore increasing synthesis gas yield and decreasing higher hydrocarbon yield were the main means of improving heat recovery. According to the path analysis diagram, there should mainly be two measures: (1) inhibit CH3 from recombining into C2H6; (2) improve O radical concentration, namely, improve reaction rate of CH3 and O combination. Figure 7(b) points out that reaction (R12) was responsible for 83% of the total electron-impact dissociation of H2O, while reaction (R13) was responsible for 3%, which was to say OH concentration was higher than O concentration. Badly most of OH was combined with CH4 to regenerate H2O. Therefore, inhibiting the combination of OH and CH4 and promoting the transformation from OH into O were the key to improve O radical concentration.

Known from surface reaction mechanism of MSR over Ni, as seen in (16)–(23) [21], choosing a suitable catalyst can guarantee free radicals produced by electron-impact reactions to adsorb onto the surface of catalysts. The selectivity characteristics of catalysts can effectively lower the recombination of alkyl and improve OH into O, which can improve the yield of synthesis gas:

To preliminarily verify the reaction path flux analysis, plasma catalytic hybrid reforming experiment was employed in DPB reactor. The operating conditions were pressure of 0.12 MPa, reaction temperature of 400°C, total flow of inlet reactants of 1.156 × 10−5 kg/s, S/C of 2, and the input power of 70.13 W. The characteristics for steam reforming are shown in Table 4. After adding Ni catalyst on discharge region, synthesis gas yield had a significant improvement, C2 + C3 yield was equal to zero, and no higher hydrocarbons were produced, with an effective carbon recovery rate of 100%. Those results verified the reaction path flux analysis, which also indirectly proved the validity of reaction mechanism for plasma-assisted MSR developed in this paper.

5. Conclusions

In this paper we designed a visual reactor and confirmed a double-dielectric structure for DPB reactor. Experimental studies of plasma-assisted MSR were performed at different S/C, residence time s, and reaction temperatures. Based on the experimental results, a detailed reaction mechanism for plasma-assisted MSR was built and developed. The results are summarized as follows.(1)DBD assisted methane steam reforming technology can improve methane conversion in low temperature without catalyst but cause a low effective carbon recovery rate. In different operating conditions, CO yield is only around 1%, lower hydrocarbons (C2, C3) yield is about 4%, and the residual of reacting CH4 is converted into higher hydrocarbons (more than C4).(2)The kinetic model developed can accurately predict methane conversion and the trend of products yield in different operating conditions. The reactions of CH3 + CH3→C2H6 and OH + CH4→H2O + CH3 act as limiting reactions for CO yield.(3)Adding Ni catalyst in discharge region can guarantee free radicals to adsorb onto the catalyst surface and thus improve yields of syngas and avoid generation of higher hydrocarbons.

Nomenclature

Variable Physical Dentitions
:Mass density (kg/m3)
:Reactor volume (m3)
:Inlet mass flow rate (kg/s)
:Outlet mass flow rate (kg/s)
:The mass fraction of the th species
:Molecular weight of the th species
:Molar rate of production of the th species (mol/m3·s)
:Mixture pressure (MPa)
:Gas temperature ()
:Electron temperature ()
:Momentum-transfer collision frequency
:Total number of electron-impact reactions
:Net rate of progress of the th reaction
:Net enthalpy change of the reaction
:Molar concentration of the th species
:Forward rate constants of the th reaction
:Reverse rate constants of the th reaction
:Stoichiometric coefficient for reactant in reaction
:Stoichiometric coefficient for product in reaction
:Preexponential factor
:Temperature exponent
:Activation energy
:Mean electron energy
Bracket :Molar concentration of species.
Subscript
:Specific species
:Specific reaction
:Electron
:Gas.
Superscript
:Inlet stream quantities.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors wish to thank Mr. Long Qiang and Mr. Xu Changsong for their assistance in constructing the test rig and also appreciate the authors of the following references.

Supplementary Materials

Supporting Information contains a total of 175 reactions developed for plasma-assisted MSR, mainly consisting of two parts: electron-impact reactions and their rate constants; radical reactions and their rate constants.

  1. Supplementary Material
  2. Supplementary Material