A New Drug Release Method in Early Development of Transdermal Drug Delivery Systems

Cai, Bing; Söderkvist, Karin; Engqvist, Håkan; Bredenberg, Susanne

doi:https://doi.org/10.1155/2012/953140

Pain Research and Treatment

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions References Copyright Related Articles

Research Article | Open Access

Volume 2012 | Article ID 953140 | https://doi.org/10.1155/2012/953140

A New Drug Release Method in Early Development of Transdermal Drug Delivery Systems

Bing Cai,¹Karin Söderkvist,²Håkan Engqvist,¹and Susanne Bredenberg^1,2

Academic Editor: Howard Smith

Received11 May 2012

Accepted28 Jun 2012

Published05 Aug 2012

Abstract

In vitro drug release tests are a widely used tool to measure the variance between transdermal product performances and required by many authorities. However, the result cannot provide a good estimation of the in vivo drug release. In the present work, a new method for measuring drug release from patches has been explored and compared with the conventional USP apparatus 2 and 5 methods. Durogesic patches, here used as a model patch, were placed on synthetic skin simulator and three moisture levels (29, 57, 198 μL cm⁻²) were evaluated. The synthetic skin simulators were collected after 1, 2, 3, 4, 6, and 24 hours and extracted with pH 1.0 hydrochloric acid solution. The drug concentrations in the extractions were measured by isocratic reverse phase high-pressure liquid chromatography. The results showed that, with the increasing moisture level on the synthetic skin simulator, the drug release rate increased. In comparison with the conventional USP method, the drug release results performed by the new method were in more correlation to the release rate claimed in the product label. This new method could help to differentiate the drug release rates among assorted formulations of transdermal drug delivery systems in the early stage of development.

1. Introduction

Transdermal patches delivers drug across skin to the circulatory system to achieve therapeutic effects [1] or to provide local effect of drugs. As one of the fastest growing drug administration routes [2], it has several advantages compared to other traditional delivery methods: controlled release rate, more stable plasma concentration, noninvasive administration, less frequent dosing, and simple application without professional medical aids [3]. Yet, a common problem with transdermal delivery systems is permeation across stratum corneum, which limits the size and properties of drug molecule to pass through. Hence, in addition to the delivery device, skin also serves as another rate-limiting step for many transdermal delivery systems [2, 4–6]. In general, the flux across the skin is dependent upon the hydration of the skin, partitioning, and transport across the stratum corneum and the concentration gradient across the skin [7]. In vitro drug release test is an important characterization tool to evaluate the performance of transdermal drug delivery systems (TDDSs). Since this type of test is less costly and easier to implement than in vivo studies [8], it is widely used for many purposes during drug development, especially for screening processes and stability assessment of new formulations [9]. USP apparatus 5 (paddle over disc), USP apparatus 6 (rotating cylinder), and USP apparatus 7 (reciprocating holder) are the recommended in vitro release testing method for transdermal delivery systems by the authorities [8, 10], but USP apparatus 2 has also been used in some in vitro studies of transdermal patches [11, 12]. However, the results of these USP methods for some TDDS were found to be difficult to correlate with the in vivo performances, especially for the patches that depend on the skin resistance as the dominating factor for the controlled release [13, 14]. USP methods are, therefore, more useful in quality control processes of TDDS, and permeation tests are commonly used alternatives to give more comparable release profile as in vivo result in transdermal formulation development. Franz diffusion cell, horizontal-type permeation systems, and flow-through diffusion cells are some well-known examples [15, 16]. In these methods, a skin or synthetic membrane is placed between the patch and a buffer, simulating the resistance and penetration effects [17]. Several studies have shown that hydration of skin and variation of skin or synthetic membrane could influence the accuracy of the method [7, 18–20]. Hence, an easy-implemented testing method, which could imitate resistance and penetration effect as skin and test under limited moisture conditions, could be helpful in the development of new formulations of TDDS.

Durogesic was used as the model test patch in this study. It is a fentanyl controlled-release transdermal patch, which is used for moderate to severe chronic pain relief. There are four strengths of the dose on the market and their stated release rate is claimed as 2.38 μg cm⁻²h⁻¹ for 72 hours [21]. The strength of the dose is proportional to the contact area of the patch. Previous studies have found that the transdermal delivery of fentanyl cause a depot in upper layers of the skin [22, 23]. The depot accumulation of the drug causes delay of drug delivery to the systemic circulation [24, 25]. This indicates that the diffusion and penetration across skin are the primary rate-limiting step of the fentanyl patches.

The purpose of this study was to develop a selective and easy-to-handle test method that could imitate the drug diffusion and moisture level of skin. The aim was that the method should provide a good indication of the in vivo performances and be helpful in screening different TDDS formulations from their release rate in the early stage of development.

2. Materials and Methods

2.1. Materials

The commercial matrix-type transdermal patch, Durogesic patches (Janssen-Cilag, Belgium) with two strengths, 12 and 75 μg/hr, was used as model patch. Fentanyl base (MacFarlan and Smith, Edinburgh, UK) was a gift from Orexo AB, Sweden. Dish sponge cloth (Wettex) is produced by the Freudenberg group (Norrköping, Sweden). The cloth is made of 35% cotton and 65% cellulose with 2 mm in thickness. In this study it served as a reservoir to collect drug and a synthetic skin simulator (SSS) to mimic the resistance and penetration effect. Its true density and porosity were measured by gas pycnometer and the values were 2.0543 g cm⁻³ and 93.7%, respectively. Reagent grade of sodium hydroxide (NaOH), 37% fuming hydrochloric acid (HCl) and monopotassium phosphate (KH₂PO₄) were purchased from Sigma-Aldrich (Stockholm, Sweden). Phosphate buffer solution was made of NaOH and KH₂PO₄ and its pH was adjusted to .

2.2. Drug Release Test of Durogesic Patch on SSS

The SSS of the correlated patch size (5.25 cm² for 12 μg/hr patch or 31.5 cm² for 75 μg/hr patch) was prepared with three different moisture level (29, 57, 198 μL cm⁻²) with pH 6.8 phosphate buffer and placed on a flat clean surface. The Durogesic patch was placed on the SSS at ambient temperature and humidity. Patch and SSS were placed on a piece of parafilm and covered with a flat metal plate on the top to avoid patch dislocation. The experimental setting is illustrated in Figure 1. The patch was moved to a new piece of wetted SSS after 1, 2, 3, 4, 6, and 24 hours and the old SSS was collected and soaked in HCl solution (pH1.0). The concentration of fentanyl in the solution was measured using isocratic reversed phase high-pressure liquid chromatography (HPLC). The experiments were performed in triplicates and the error bars were denoted by confidential interval. The fraction of drug release was calculated from the total amount of drug in the patch which was referred to the label claim [21].

2.3. Drug Release Test of Durogesic Patch Using USP Apparatus 5

Dissolution bath apparatus 2 with mini vessels (Sotax AT7 Smart, Sotax AG, Switzerland) was used to perform the release test for 12 μg/hr patches. The patches were fixed in the so-called japaneese baskets and placed at the bottom of the vessel in 200 mL pH 6.8 phosphate buffer. While for 75 μg/hr patches, dissolution bath apparatus 5 (Sotax AT7 Smart, Sotax AG, Switzerland) was used. The patches were glued to metal disks and placed at the bottom of the vessel in 900 mL pH 6.8 phosphate buffer with its release surface up. Both dissolution tests were performed with paddle speed of 50 rpm at 37°C. The concentration of fentanyl in the solution was measured using isocratic reversed phase liquid HPLC. The experiments were performed in duplicates and the error bar of each point was denoted by the confidential interval. The fraction of drug release was calculated from the total amount of drug in the patch which was referred to the label claim [21].

2.4. Analysis of Dissolution Curve

Similarity factor, , is one of the statistic tools to compare the dissolution profile and recommended by Polli and his colleagues [26]. It is also used by FDA and EMEA guidelines to compare dissolution curves for solid oral dosage forms [27, 28] and has been adopted by many studies to compare dissolution profile of different transdermal patch formulations [29–31]. Higher value indicates higher similarity of two profiles, that is, two identical profiles gives equals to 100. Two dissolution profiles are considered comparable when is larger than 50. The formula of is shown as (see [32]), represents the number of time points for each measurement and is the fraction of release at time point . Subscript and indicates test and reference, respectively. In this study, tests were results from USP apparatus 5 and SSS method, and the reference was the stated release profile.

3. Results and Discussion

3.1. Effect of the Amount of Moisture on the SSS on Release Rate

Generally, accumulated moisture between patch and skin is unavoidable and influences the rate of drug transport across the skin [20] and, therefore, drug release rates from the model patches were measured on the SSS with different moisture levels. The results showed that the drug release rate increased with increasing humidity level within 24 hours, see Figure 2. For both strengths of the patches, the release rates were similar under low and moderate moisture conditions but increased significantly under the high moisture condition. Release profiles obtained under low and moderate moisture on SSS were more similar to the stated clinical release of the patch. The release profile of larger patch had a higher correlation to the stated clinical release, which might result from the less edge effect comparing to smaller patch, that is, a smaller portion of the total amount of drug was released from the edge of the larger patch.

(a)

(b)

The results showed that a change of moisture level could cause the considerable change of the release profile and that the diffusion of fentanyl from the patch increased with the amount of accessible moisture. Therefore, the level of humidity on SSS should be carefully chosen to simulate the proper moisture between the patch and the skin. In this study, the moderate humidity, that is, 57 μL cm⁻², added to the SSS was the most suitable for Durogesic patch.

3.2. Comparison of an USP Method and the SSS Method

As shown in Figure 3, Durogesic patch released more than 90% of fentanyl content within 5 hours using the USP method for both strengths, while the release profiles obtained by the SSS method with the moderate humidity on the SSS indicated a prolonged drug release. The release profiles were also compared with stated release of the patch, using similarity factor, as shown in Table 1. The results showed that the dissolution profile obtained from the SSS method was more comparable to the release claimed in the product label. In addition, the results correlates well to results reported in a previous study using the Franz cell method where the drug release rate varied between 1400 to 2600 ng cm⁻²h⁻¹ [33].

(a)

(b)

Further, the drug release could be limited by a low dissolution rate of fentanyl in PH 6.8 and thus did not fit either the zero or first order release model [34]. Since the USP method provides sink condition, drug can be released with less “skin resistance.” This leads to a overestimation of the drug release from the patches where the drug diffusion mainly depends on skin permeation, thereby showing low correlation with the drug release profile with in vivo studies [13]. The results in this study indicate that the SSS method could imitate the skin resistance effect better than the USP method for Durogesic patches. The new method could therefore simulate the diffusion resistance and thus provide a significantly better estimation of in vivo performance than the USP method.

3.3. Limitations of the SSS Method and Further Work

The SSS method is an easy-implemented method developed for screening transdermal formulations in the early development. However, during the experiment, incomplete extraction of the drug from the SSS and drug release from the edges of the patch could be a possible source of errors in the measurement of drug release profiles. Fentanyl has a much higher solubility at lower pH [34] and the drug diffusion was regarded in equilibrium after extraction. Thus, nearly all amount of the drug should be released from the SSS and extraction should be considered to be complete. We found that a small amount of fentanyl was further released from the SSS after the first extraction. To minimize drug leaking out from the edge of the patch, the SSS was cut in the same size as the patch. Although those effects were insignificant, other error sources, such as evaporation of moisture, saturation on SSS, and temperature effect, could exist in the SSS method. Sealing the patch and SSS, replacing the SSS more frequently and testing under 32°C could help to reduce the potential errors.

The scope of this study was to give a preliminary evaluation on the SSS method and a understanding of the effect of the amount of moisture on the drug release profiles of Durogesic patches. There are more interesting aspects that could be further investigated, such as estimation on the evaporation during testing, investigation of the saturation effect of the SSS, and assessment on other commercial transdermal products.

4. Conclusions

A simple, low-cost, and selective method for measuring release rate of transdermal drug delivery system has been developed and evaluated. This method is based on a moisturized synthetic skin simulator (SSS), providing release resistance as well as a moisture and reservoir function for the drug released from the model patch. It was found that the drug release rate increased with increasing humidity level on SSS. This method showed a more valid way to measure the drug release profile than using the conventional in vitro release USP method. It could be particularly helpful in the work of screening various formulations in an early stage of research and development of transdermal drug delivery systems.

Conflict of Interests

The authors have no personal financial or nonfinancial conflict of interests related to the publication of this paper.

Acknowledgment

Orexo AB is acknowledged for supplying the materials and analytical support, and Vinnova is acknowledged for financial contribution.

References

M. E. Aulton, Aulton's Pharmaceutics: The Design and Manufacture of Medicines, Churchill Livingstone, Edinburgh, NY, USA, 3rd edition, 2007.
M. R. Prausnitz, S. Mitragotri, and R. Langer, “Current status and future potential of transdermal drug delivery,” Nature Reviews Drug Discovery, vol. 3, no. 2, pp. 115–124, 2004.
View at: Google Scholar
M. R. Prausnitz and R. Langer, “Transdermal drug delivery,” Nature Biotechnology, vol. 26, no. 11, pp. 1261–1268, 2008.
View at: Publisher Site | Google Scholar
J. Hadgraft, D. Beutner, and H. M. Wolff, “In vivo-in vitro comparisons in the transdermal delivery of nitroglycerin,” International Journal of Pharmaceutics, vol. 89, no. 1, pp. R1–R4, 1993.
View at: Publisher Site | Google Scholar
S. Prodduturi, G. J. Smith, A. M. Wokovich, W. H. Doub, B. J. Westenberger, and L. Buhse, “Reservoir based fentanyl transdermal drug delivery systems: effect of patch age on drug release and skin permeation,” Pharmaceutical Research, vol. 26, no. 6, pp. 1344–1352, 2009.
View at: Publisher Site | Google Scholar
L. V. Allen Jr., “Transdermals: the skin as part of a drug delivery system,” International Journal of Pharmaceutical Compounding, vol. 15, no. 4, pp. 308–315, 2011.
View at: Google Scholar
H. A. E. Benson, “Transdermal drug delivery: penetration enhancement techniques,” Current Drug Delivery, vol. 2, no. 1, pp. 23–33, 2005.
View at: Publisher Site | Google Scholar
O. Anand, L. X. Yu, D. P. Conner, and B. M. Davit, “Dissolution testing for generic drugs: an FDA perspective,” Aaps Journal, vol. 13, no. 3, pp. 328–335, 2011.
View at: Google Scholar
C. Tong, R. Lozano, Y. Mao et al., “The value of in Vitro dissolution in drug development: a position paper from the AAPS in Vitro release and dissolution focus group,” Pharmaceutical Technology, vol. 33, no. 4, pp. 52–64, 2009.
View at: Google Scholar
C. T. Ueda, M. Marques, V. P. Shah et al., “Topical and transdermal drug products,” Pharmacopeial Forum, vol. 35, no. 3, pp. 750–764, 2009.
View at: Google Scholar
R. O. Salama, D. Traini, H. K. Chan, and P. M. Young, “Preparation and characterisation of controlled release co-spray dried drug-polymer microparticles for inhalation 2: evaluation of in vitro release profiling methodologies for controlled release respiratory aerosols,” European Journal of Pharmaceutics and Biopharmaceutics, vol. 70, no. 1, pp. 145–152, 2008.
View at: Publisher Site | Google Scholar
P. Costa, “An alternative method to the evaluation of similarity factor in dissolution testing,” International Journal of Pharmaceutics, vol. 220, no. 1-2, pp. 77–83, 2001.
View at: Publisher Site | Google Scholar
R. H. Guy and J. Hadgraft, “Rate control in transdermal drug delivery?” International Journal of Pharmaceutics, vol. 82, no. 3, pp. R1–R6, 1992.
View at: Publisher Site | Google Scholar
J. C. Olivier, S. Rabouan, and W. Couet, “In vitro comparative studies of two marketed transdermal nicotine delivery systems: nicopatch and Nicorette,” International Journal of Pharmaceutics, vol. 252, no. 1-2, pp. 133–140, 2003.
View at: Publisher Site | Google Scholar
S. Azarmi, W. Roa, and R. Löbenberg, “Current perspectives in dissolution testing of conventional and novel dosage forms,” International Journal of Pharmaceutics, vol. 328, no. 1, pp. 12–21, 2007.
View at: Publisher Site | Google Scholar
S. Azarmi, W. Roa, and R. Löbenberg, “Current perspectives in dissolution testing of conventional and novel dosage forms,” International Journal of Pharmaceutics, vol. 328, no. 1, pp. 12–21, 2007.
View at: Publisher Site | Google Scholar
B. W. Kemppainen and W. G. Reifenrath, Methods for Skin Absorption, CRC Press, Boca Raton, Fla, USA, 1990.
Y. Levintova, F. M. Plakogiannis, and R. A. Bellantone, “An improved in vitro method for measuring skin permeability that controls excess hydration of skin using modified Franz diffusion cells,” International Journal of Pharmaceutics, vol. 419, no. 1-2, pp. 96–106, 2011.
View at: Publisher Site | Google Scholar
D. A. Van Hal, E. Jeremiasse, H. E. Junginger, F. Spies, and J. A. Bouwstra, “Structure of fully hydrated human stratum corneum: a freeze-fracture electron microscopy study,” Journal of Investigative Dermatology, vol. 106, no. 1, pp. 89–95, 1996.
View at: Google Scholar
E. W. Smith and H. I. Maibach, Percutaneous Penetration Enhancers, CRC/Taylor & Francis, Boca Raton, Fla, USA, 2nd edition, 2006.
A. M. MacConnachie, “Fentanyl transdermal (Durogesic, Janssen),” Intensive and Critical Care Nursing, vol. 11, no. 6, pp. 360–361, 1995.
View at: Google Scholar
R. B. R. Muijsers and A. J. Wagstaff, “Transdermal fentanyl: an updated review of its pharmacological properties and therapeutic efficacy in chronic cancer pain control,” Drugs, vol. 61, no. 15, pp. 2289–2307, 2001.
View at: Google Scholar
V. Coopman, J. Cordonnier, K. Pien, and D. Van Varenbergh, “LC-MS/MS analysis of fentanyl and norfentanyl in a fatality due to application of multiple Durogesic transdermal therapeutic systems,” Forensic Science International, vol. 169, no. 2-3, pp. 223–227, 2007.
View at: Publisher Site | Google Scholar
G. K. Gourlay, S. R. Kowalski, J. L. Plummer, D. A. Cherry, P. Gaukroger, and M. J. Cousins, “The transdermal administration of fentanyl in the treatment of postoperative pain: pharmacokinetics and pharmacodynamic effects,” Pain, vol. 37, no. 2, pp. 193–202, 1989.
View at: Google Scholar
A. M. MacConnachie, “Analgesics in the management of chronic pain. Part five: step 3 parenteral analgesic drug therapy,” Intensive & Critical Care Nursing, vol. 15, no. 1, pp. 58–60, 1999.
View at: Google Scholar
J. E. Polli, G. S. Rekhi, L. L. Augsburger, and V. P. Shah, “Methods to compare dissolution profiles and a rationale for wide dissolution specifications for metoprolol tartrate tablets,” Journal of Pharmaceutical Sciences, vol. 86, no. 6, pp. 690–700, 1997.
View at: Publisher Site | Google Scholar
Note for guidance on the investigation of bioavailability and bioequivalence, C.f.p.m. products, T.e.a.f.t.e.o.m. products, and E.o.m.f.h. use, Ed, European Medicines Agency, London, UK, 2000.
B. Documentation, “Guidance for industry? Immediate release solid oral dosage forms,” Pharmaceutical Process Scale-Up, vol. 118, p. 353, 2001.
View at: Google Scholar
K. D. Mpharm, K. P. Mpharm, and S. Chakravarthi, “Preparation and evaluation of transdermal plasters containing norfloxacin: a novel treatment for burn wound healing,” Eplasty, vol. 10, article e44, 2010.
View at: Google Scholar
S. T. Prajapati, C. G. Patel, and C. N. Patel, “Formulation and evaluation of transdermal patch of repaglinide,” ISRN Pharmaceutics, vol. 2011, Article ID 651909, 9 pages, 2011.
View at: Publisher Site | Google Scholar
M. X. Zhou, D. Shoudt, G. Calderon, and M. Feng, “Application of USP apparatus 7 to in vitro drug release in scopolamine transdermal systems,” Dissolution Technologies, vol. 14, no. 2, pp. 25–30, 2007.
View at: Google Scholar
V. P. Shah, Y. Tsong, P. Sathe, and J. P. Liu, “In vitro dissolution profile comparison—statistics and analysis of the similarity factor, f2,” Pharmaceutical Research, vol. 15, no. 6, pp. 889–896, 1998.
View at: Publisher Site | Google Scholar
R. H. Larsen, F. Nielsen, J. A. Sørensen, and J. B. Nielsen, “Dermal penetration of fentanyl: inter- and intraindividual variations,” Pharmacology and Toxicology, vol. 93, no. 5, pp. 244–248, 2003.
View at: Publisher Site | Google Scholar
S. D. Roy and G. L. Flynn, “Solubility behavior of narcotic analgesics in aqueous media: solubilities and dissociation constants of morphine, fentanyl, and sufentanil,” Pharmaceutical Research, vol. 6, no. 2, pp. 147–151, 1989.
View at: Google Scholar

Copyright

Copyright © 2012 Bing Cai et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

8780

Downloads

1628

Citations