Dielectric Properties of La2O3 Doped Composite (PbxSr1−x)TiO3 Borosilicate Glass Ceramic

Gautam, C. R.; Kumar, Devendra; Parkash, Om; Thakur, O. P.

doi:https://doi.org/10.1155/2013/879758

Journal of Ceramics

On this page

Abstract Introduction Materials and Methods Results Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2013 | Article ID 879758 | https://doi.org/10.1155/2013/879758

Dielectric Properties of La₂O₃ Doped Composite (Pb_xSr_1−x)TiO₃ Borosilicate Glass Ceramic

C. R. Gautam,¹Devendra Kumar,²Om Parkash,²and O. P. Thakur³

Academic Editor: Zhenxing Yue

Received13 Jul 2012

Revised03 Nov 2012

Accepted07 Nov 2012

Published05 Dec 2012

Abstract

Ferroelectric (Pb_xSr_1-x)TiO₃ (PST) perovskite phase has been crystallized in borosilicate glassy matrix with a suitable choice of composition and heat treatment schedule. La₂O₃ is a donor dopant for PST and can make it semiconducting. Dispersion of semiconducting perovskite phase in insulating glassy matrix in glass-ceramic samples may lead to the formation of space charge polarization around crystal-glass interface, leading to a high value of effective dielectric constant, . Therefore, with the aim of the developing glass ceramics with high dielectric constant, glasses in the system 64[(Pb_xSr_1-x)O·TiO₂]-25[2SiO₂·B₂O₃]-5[K₂O]-5[BaO]-1[La₂O₃] have been prepared (). It is found that the addition of La₂O₃ strongly affected the crystallization and dielectric behavior of glass-ceramic with PST perovskite phase. All glass ceramic samples show a diffuse broad Curie peak in their versus T plots. Curie peak temperature, , depends on compositions of the glass-ceramic samples as well as frequency of measurements.

1. Introduction

Lead titanate is a ferroelectric material having a cubic crystal structure similar to BaTiO₃ with a high Curie point (490°C). On decreasing the temperature through the Curie point a phase transition from paraelectric cubic phase to ferroelectric tetragonal phase takes place [1]. In recent years a considerable amount of work has been done on the ferroelectric properties of BaTiO₃. In addition to BaTiO₃, there are other different perovskites which have been reported as ferroelectrics [2]. On heating, BaTiO₃ undergoes a ferroelectric/paraelectric phase transition to the cubic polymorphism at a Curie temperature, , of ~130°C, at which high value of dielectric constant is 10,000 in undoped ceramic samples. The phase transition is first order, and the peak in is correspondingly sharp [3]. PbTiO₃ shows higher temperature applications, since its Curie temperature, , has been reported to lie in the neighborhood of 500°C (490°C). Moreover the axial ratio for PbTiO₃ in the tetragonal phase is 1.063, markedly larger than that in BaTiO₃. Hence it is expected that PbTiO₃ should possess outstanding ferroelectric properties. PbTiO₃ and SrTiO₃ ceramics are well known to form solid solution (Pb_xSr_1-x)TiO₃ (PT-ST) with each other over the entire range of composition, that is, for . Curie temperature, , is one parameter, which is very sensitive to the composition, . , of PT-ST solid solution series that has been reported to vary linearly with composition “” [4]. These ceramics with donor doping have high-value dielectric constant due to space charge polarization at semiconducting grains and insulating grain boundary or phases and show relaxer like behavior [5]. Various studies on the crystallization behavior and dielectric properties of glass-ceramics containing crystalline phase such as PbTiO₃ [6–14] and SrTiO₃ have been reported [15–22]. Studies on crystallization and dielectric behavior of solid solution lead strontium titanate glass-ceramics have been carried out by Sahu et al. [23–26]. Strontium rich glass-ceramics have cubic crystal phases and are nonferroelectric, whereas lead rich glass-ceramics are ferroelectric and Curie temperature linearly decreases with increasing strontium. No report is available on the very high value of dielectric constant in PT and ST or PST glass-ceramic system in the literature. While exploring the possibility of crystallization of perovskite SrTiO₃ phase in borosilicate glass, Thakur et al. also considered it worthwhile to study the effect of different rare earth and transition metal oxide additives on crystallization, a microstructural and dielectric behavior of SrTiO₃-based glass-ceramics. It was reported that these additives also act as dopants for SrTiO₃ phase and change its electrical characteristics, resulting in a high value of dielectric constant due to space charge polarization at semiconducting crystal and insulating glass interface.

In the present paper efforts have been made to achieve a high value of dielectric constant in the PST borosilicate glass-ceramic system using a rare earth La₂O₃ as a dopant. The value of dielectric constant mainly depends on the crystallization behavior of the glasses and also on the doping. Perovskite PST solid solution phase has crystallized in borosilicate glassy matrix successfully. To see the effect of holding time on the dielectric properties of the glass-ceramic samples, all the glasses were crystallized for 3 hours. The determination of , of glass-ceramic samples, may provide information regarding the composition of the perovskite ferroelectric phase crystallized in various compositions.

2. Materials and Methods

Glasses in the present system 64[(Pb_xSr_1-x)OTiO₂]-25[2SiO₂B₂O₃]-5[K₂O]-5[BaO]-1[La₂O₃] () were prepared by conventional melt quench method. Well mixed, dried powders containing appropriate amount of reagent grade PbO, SrCO₃, TiO₂, SiO₂, H₃BO₃, K₂CO₃, BaCO₃, and La₂O₃ were melted in pure alumina crucibles for an hour in the temperature range 1120–1240°C under normal atmospheric conditions. The melt was quenched by pouring it in an aluminum mould and pressing with a thick aluminum plate. The glasses were then annealed at 400°C for 4?hr. Glass-ceramic samples were prepared by subjecting glasses to various heat treatment schedules based on their DTA results. Phases were identified using powder X-ray diffraction (XRD) analysis. Diffraction patterns were recorded employing a Rigaku ID 3000 diffractometer using Cu radiation. The crystalline phase in each glass-ceramic sample was identified by comparing its XRD pattern with standard patterns of various crystalline phases which might have formed from different constituent oxides of the glass. The glass-ceramic samples were polished, etched with of 30 and 20 percent of HNO₃ and HF solution for 60 seconds. Etched glass-ceramic samples were coated with a thin film of gold for SEM. Observations were taken by using model number JSM-840.

For dielectric measurement of glass-ceramic samples, both the surfaces of these samples were ground and polished using SiC powders for attaining smooth surfaces to a thickness of 0.5 to 1?mm. The electrodes were made by applying silver paint (code Number 1337—A, Elteck Corporation, India) on both sides of the specimen and curing at 700°C for 5 minutes. The capacitance, , measurements were made in a locally fabricated sample holder using an automated measurement system during heating. The sample was mounted in the sample holder, which was kept in a programmable heating chamber. The leads from the sample holder were connected to HP 4284?A, Precision LCR meter through scanner relay boards, and HPIB bus, which in turn was connected to a computer and printer. Measurement operational controls and data recording are done through the computer. The sample was heated in the heating chamber to the required temperature at a rate of 2°C/min. and dissipation factor, , of the glass-ceramic samples were recorded with 0.1, 1, 10, 100?KHz, and 1?MHz at equal intervals of time during heating in the temperature range ~27–500°C. Dielectric constant, , was calculated from the measured , using the following equation: where is the capacitance in farad, F, is the permittivity of free space (8.854 × ?F/m), is the thickness (m), and is the area (m²) of the samples. The and were plotted as a function of , at a few selected frequencies to show the variation of , with , and frequency of applied electric field.

Dissipation factor was noted directly or calculated by using the following relation: where , -is the frequency, and is the conductance.

Five letters glass code represents the composition of the glass. First two letters PT, 9P, and so forth designate the fraction of lead, Pb, that is, in the glass. PT refers to , that is, 100 percent Pb. 9P, 8P, and so forth refer to and so forth, respectively. The third letter L indicates that La₂O₃ is used as an additive. The last two letters 5B indicate to fraction of BaO. For the nomenclature of the glass-ceramic samples the first five letters in the code samples are similar to the code of their parent glass. Next three digits indicate the crystallization temperature. The last letter T refers to 3 hours holding time at crystallization temperature. For example the glass-ceramic code PTL5B700T represents the glass-ceramic sample prepared from the parent glass PTL5B heat treated at 700°C for 3 hours. Similar coding processes have been adopted for the other glass-ceramic samples as shown in the Table 1.

3. Results

3.1. XRD Analysis

XRD patterns for glass-ceramic samples PTL5B700T, 8PL5B726T, 7PL5B739T, and 6PL5B730T, respectively, are shown in Figure 1. It is observed from the XRD patterns that perovskite PbTiO₃ (P) or (PbSr)TiO₃ (PST) is the major crystalline phase, PbTi₃O₇ (PT), and TiO₂ (R) are the secondary minor phases in these glass-ceramics. The nature as well as amount of the minor phases depend on the initial compositions, , of the glass and heat treatment schedule. The structure of major crystalline phase is tetragonal similar to PbTiO₃, and its lattice parameters, “” and “,” depend on the composition of the glass-ceramics, and the crystallization temperature. The axial ratio, , decreases with increasing Sr content similar to (PbSr)TiO₃ solid solution ceramics. More results on lattice parameters and crystal structure are discussed in earlier published research paper [27].

3.2. Scanning Electron-Microscopic Analysis

Figures 2(a)–2(e) show scanning electron micrographs of a few selected glass-ceramic samples PTL5B700T, 9PL5B695T, 8PL5B726T, 7PL5B739T, and 5PL5B806T, respectively. The SEM micrographs show that submicrometer crystallites are uniformly distributed in the glassy matrix. The volume fraction of crystallites is large in comparison to the volume fraction of the residual glass. It indicates that La₂O₃ acts as a nucleating agent and promotes the crystallization of perovskite phase [28]. Figure 2(c) shows dispersion and clear phase separation of the major perovskite phase in the glassy matrix. Well-developed interconnected and randomly distributed grains of the major crystalline phase have been clearly observed in the scanning electron micrograph of glass-ceramic sample 7PL5B739T (Figure 2(d)). Figure 2(e) depicts the SEM image of glass-ceramic sample 5PL5B806T crystallized at 739°C for 3?hr heat treatment schedule of the parent glass. The crystallized major phase of (PbSr)TiO₃ along with pyrochlore phase of rutile, R, distributed randomly inside the residual glassy matrix. The pyrochlore phase of R is also confirmed from XRD analysis for the same glass-ceramic sample. The shift in XRD peak positions of PbTiO₃ in the glass-ceramic samples as compared with the standard PbTiO₃ is reflected in the values of their lattice parameters. It may be due to the formation of lead titanate perovskite phase of solid solution of crystallites [27].

(a)

(b)

(c)

(d)

(e)

3.3. Dielectric Properties

The variation of dielectric constant, , and dissipation factor, , for different glass-ceramic samples in the present system are shown in Figures 3–5. Figure 3 shows the dielectric behavior for the glass-ceramic sample PTL5B700T obtained by crystallizing glass at 700°C. Dielectric behavior of this glass-ceramic sample show very small temperature dependence of dielectric constant up to 200°C at all frequencies. Beyond this temperature, the magnitude of increases with increasing temperature, , at 0.1, 1.0, and 10 KHz. The increase in the is higher at smaller frequencies. These glass-ceramics contain alkali ions, which are having high mobility. Increase in and may be due to increase in electrical conduction with increasing . Broad peak can be associated with ferroelectric to paraelectric phase transitions in PbTiO₃, crystallites present in the versus as well as versus plots for this glass-ceramic sample. The temperature is very close to the Curie temperature, of PbTiO₃ glass-ceramics (Table 1). Variation of versus shows almost similar behaviors except that broad peaks are observed within the same temperature range. These peaks are shifted toward higher-temperature side with increasing frequency, , and show relaxor like behavior. In relaxor ferroelectrics a peak in versus plots is observed at different frequencies. Since the increases rapidly with increasing , around this temperature, this peak seems to be hidden by rapidly rising in due to rapidly increasing space charge polarization with . Figures 4 and 5 depict variation of and versus , for the glass-ceramic samples 8PL5B726T and 6PL5B730T. The variation of with , for both glass-ceramic samples, is almost similar while the variation of with is different. A broad peak is observed there versus plots. The broadening in the peaks of 6PL5B730T with increasing frequency is more in comparison to the glass-ceramic sample 8PL5B726T [29]. This is due to increasing concentration of Sr. It is also observed that the position of the peak shifts to higher temperature with increasing , in both plots as well as in versus plots. After this peak, the dielectric loss, , again increases rapidly with increasing . The dielectric constant, , strongly depends on the (Figure 5). It is observed from the plot of this glass-ceramic sample that the value of rapidly increases with increasing, , peaks and then decreases followed by another increase with temperature at 0.1?KHz. Two peaks are observed at a frequency of 0.1?KHz at temperatures 206 and 440°C, respectively. The first peak may be due to ferroelectric to paraelectric phase transition while the second peak may be due to relaxation polarization. is strongly dependent on , around Curie temperature, . The peak temperatures at 0.1, 1, 10, and 100?KHz frequencies are found to be 206, 219, 228, and 229°C, respectively. The various dielectric parameters such as grain size, at 1 KHz, at and of Pb_xSr_1-xTiO₃ Pb-rich glass-ceramics studied in the present investigation are presented in Table 1.

(a)

(b)

(a)

(b)

(a)

(b)

A broad peak is observed in versus plots whose position is dependent on frequency. Pb_0.8Sr_0.2TiO₃ () ceramic composition shows peak due to ferroelectric to paraelectric transformation at Curie temperature ~320°C. The presence of similar peak in versus plots for these glass-ceramic samples is attributed to ferroelectric to paraelectric phase transformation of the crystallites embedded in the glassy matrix. The dissipation factor, versus plots for these glass-ceramic samples shows a peak (Figure 4) whose position shifts to higher-temperature side with increasing frequency. This indicates the presence of some relaxation polarization phenomena at around values. The ferroelectric-to-paraelectric transformation and relaxation polarization increases the broadness of versus peak with increased peak height. The dielectric characteristics of these glass-ceramic samples are very much closer to ferroelectric relaxor like ceramic materials. The increase of dielectric loss and dielectric constant beyond may be attributed to space charge polarization present at crystallites-glass interface due to increase in conduction losses [30]. Figure 6 shows variation of with, , at 1?MHz for the various glass-ceramic samples PTL5B700T, 8PL5B726T, and 6PL5B730T. The shift of Curie temperature to a lower value from that of PbTiO₃ may be a result of the formation of (PbSr)TiO₃ solid solution crystallized in glassy matrix. The shift may also be related to the strain due to crystal clamping [9] and to the effect of particle size [31–33]. Crystal clamping can shift by a few degrees only. Particle size comes into play only for particles smaller than 0.02?µm, and the ferroelectric to paraelectric phase transition is less susceptible to particle size effects. Only particle size has a significant effect on the nature of the peak, and not transition temperature. In all glass-ceramic samples, the crystallites are in the micrometer size range [34]. Thus the continuation of particle size to shifting the Curie temperature is also ruled out.

3.4. Ferroelectric Behavior

In most ferroelectrics, the temperature dependence of the relative permittivity above the (in paraelectric phase regime) can be described accurately by a simple relationship called the Curie-Weiss law [35]. Consider where is the permittivity of the material, is the permittivity of vacuum, is the Curie constant and is the Curie temperature. The Curie temperature is different from the Curie point . is a formula constant obtained by extrapolation, while is the actual temperature where the crystal structure changes. For first-order transitions while for second-order phase transitions [36]. Figure 7 shows the variation of inverse of with , in the vicinity of transition temperature for Pb_0.8Sr_0.2TiO₃ ceramics crystallized at 726°C. The dielectric data show clearly first-order phase transition and excellent Curie-Weiss behavior. The Curie constant, , obtained for this sample is 1.1 × 10^5°C.

3.5. Discussion

versus plots for the glass-ceramic samples PTL5B700T and 8PL5B726T show a peak (Figures 8 and 9). The position of the peak shifts to higher temperature with increasing frequency. After this peak, again increases rapidly with increasing temperature. It indicates that some relaxation polarization mechanism is operative in these glass-ceramics. The inverse of frequency of measurement represents the relaxation time, , of the polarization process at the peak temperature. Plots of log? versus for the glass-ceramic samples PTL5B700T and 8PL5B726T are shown in Figures 8 and 9. The plots are linear and obey Arrhenius relationship. Consider where is the activation energy for the relaxation process. Value of for the glass-ceramic samples 8PL5B726T, and 6PL5B730T is 1.27, 0.92 and 0.011?eV respectively. In these glass-ceramics, the peak in their versus plots occurs close to for the corresponding Pb_xSr_1-xTiO₃ solid solution ceramic composition (Table 1). The peaks in versus plots for these glass-ceramic samples correspond to of the crystallites embedded in the glassy matrix. versus plots indicate the presence of some relaxation polarization processes. The simultaneous presence of ferroelectric to paraelectric transition and relaxation polarization increases the broadness of versus peaks with increased peak height. Dielectric characteristics of these glass-ceramic samples are very much similar to ferroelectric relaxor materials. Small concentration of donor dopants such as La³⁺ in perovskite ceramics is known to induce an n-type semiconductivity by electronic compensation [37]. Consider At higher concentration, titanium vacancies form for compensating La³⁺ doping

The overall effect of La₂O₃ doping in perovskite ceramics (e.g., BaTiO₃) is described by the combination of above two mechanisms contributing to increase in broadness of Curie peak exhibiting ferroelectric relaxor like behavior [37]. More recently similar dielectric relaxation and effect of donor-doped Nb₂O₅ and La₂O₃ were reported [38, 39].

4. Conclusions

Differential thermal analysis (DTA) plots show more than one peak in the Pb-rich compositions. These peaks are sharp. Doping of La₂O₃ affects the crystallization behavior and dielectric properties of the glass-ceramic samples. The addition of La₂O₃ promotes nucleation and crystal growth of major phase and retards the crystallization of minor phases. XRD of Pb-rich glass-ceramic samples show that major phase of P or perovskite PST and secondary phases of PbTi₃O₇ (PT), rutile, . versus plots show high value of for 3-hour heat treatment due to better crystallization of the parent glass. It has been observed that the dielectric constant of these glass-ceramics is very high (of the order of thousands) unlike that of glass-ceramics obtained from glasses without the addition of La₂O₃. A broad peak similar to relaxor ferroelectrics whose position shifts to lower temperature with increasing Sr content in the glass-ceramic samples is observed. The dielectric behavior of these glass-ceramic samples is attributed to space charge polarization associated with ferroelectric to paraelectric phase transition similar to relaxor-like materials. Glass-ceramic samples 8PL5B726T, and 6PL5B730T shows high value of dielectric constant with small temperature dependence. These may be used for ceramic capacitor applications.

Acknowledgments

The authors would like to thank the Defence Research Development Origination, India, for financial support, Professors D. Pandey for XRD facility, School of Materials Science and Technology, IIT-BHU, Varanasi, India.

References

K. M. Rittenmyer and R. Y. Ting, “Piezoelectric and dielectric properties of calcium and samarium modified lead titanate ceramics for hydroacoustic applications,” Ferroelectrics, vol. 110, pp. 171–182, 1990.
View at: Google Scholar
V. G. Bhide, K. G. Deshmukh, and M. S. Hegde, “Ferroelectric properties of PbTiO₃,” Physica, vol. 28, no. 9, pp. 871–876, 1962.
View at: Google Scholar
M. E. Lines and A. M. Glass, Principles of Ferroelectrics and Related Materials, Clarendon Press, Oxford, UK, 1977.
S. Subrahmanyam and E. Goo, “Nucleation of the ferroelectric phase in the (Pb_xSr_1−x)TiO₃ system,” Acta Materialia, vol. 46, no. 3, pp. 817–822, 1998.
View at: Google Scholar
I. Burn and S. Neirman, “Dielectric properties of donor-doped polycrystalline SrTiO₃,” Journal of Materials Science, vol. 17, no. 12, pp. 3510–3524, 1982.
View at: Publisher Site | Google Scholar
C. G. Bergeron and C. K. Russell, “Nucleation and growth of lead titanate from a glass,” Journal of American Ceramic Society, vol. 48, no. 3, pp. 115–118, 1965.
View at: Google Scholar
D. G. Grossman and J. O. Isard, “Lead titanate glass-ceramics,” Journal of American Ceramic Society, vol. 52, pp. 230–231, 1969.
View at: Google Scholar
D. G. Grossman and J. O. Isard, “Crystal clamping in PbTiO₃ glass-ceramics,” Journal of Materials Science, vol. 4, no. 12, pp. 1059–1063, 1969.
View at: Publisher Site | Google Scholar
S. M. Lynch and J. E. Shelby, “Crystal clamping in lead titanate glass-ceramics,” Journal of the American Ceramic Society, vol. 67, no. 6, pp. 424–427, 1984.
View at: Google Scholar
T. Kokubo and M. Tashiro, “Dielectric properties of fine-grained PbTiO₃ crystals precipitated in a glass,” Journal of Non-Crystalline Solids, vol. 13, no. 2, pp. 328–340, 1974.
View at: Google Scholar
W. Mianxue and Z. Peinan, “Piezoelectricity, pyroelectricity and ferroelectricity in glass ceramics based on PbTiO₃,” Journal of Non-Crystalline Solids, vol. 84, no. 1–3, pp. 344–351, 1986.
View at: Google Scholar
J. J. Shyu and Y. S. Yang, “Crystallization of a PbO-BaO-TiO₂-Al₂O₃-SiO₂ glass,” Journal of the American Ceramic Society, vol. 78, no. 6, pp. 1463–1468, 1995.
View at: Google Scholar
A. Bahrami, Z. A. Nemati, P. Alizadeh, and M. Bolandi, “Crystallization and electrical properties of [(Pb_1−xSr_x)·TiO₃][(2SiO₂· B₂O₃)][K₂O] glass-ceramics,” Journal of Materials Processing Technology, vol. 206, no. 1–3, pp. 126–131, 2008.
View at: Publisher Site | Google Scholar
S. Golezardi, V. K. Marghussian, A. Beitollahi, and S. M. Mirkazemi, “Crystallization behavior, microstructure and dielectric properties of lead titanate glass ceramics in the presence of Bi₂O₃ as a nucleating agent,” Journal of the European Ceramic Society, vol. 30, no. 6, pp. 1453–1460, 2010.
View at: Publisher Site | Google Scholar
K. Saegusa, “PbTiO₃-PbO-B₂O₃ glass-ceramics by a sol-gel process,” Journal of the American Ceramic Society, vol. 79, no. 12, pp. 3282–3288, 1996.
View at: Google Scholar
W. N. Lawless, “Three application areas for strontium titanate glass-ceramics,” Ferroelectrics, vol. 3, pp. 287–293, 1971.
View at: Google Scholar
W. N. Lawless, “Some low-temperature properties and applications of SrTiO₃ crystallized from glass,” Ferroelectrics, vol. 7, pp. 379–381, 1974.
View at: Google Scholar
S. L. Swartz, M. T. Lanagan, W. A. Schulze, and L. E. Cross, “Dielectric properties of SrTiO₃ glass-ceramics,” Ferroelectrics, vol. 50, pp. 313–318, 1983.
View at: Google Scholar
S. L. Swartz, A. S. Bhalla, L. E. Cross, C. F. Clark, and W. N. Lawless, “Low-temperature dielectric properties of SrTiO₃ glass-ceramics,” Journal of Applied Physics, vol. 60, no. 6, pp. 2069–2081, 1986.
View at: Publisher Site | Google Scholar
S. L. Swartz, E. Breval, and A. S. Bhalla, “Effect of nucleation on the crystallization and dielectric properties of strontium titanate glass-ceramics,” American Ceramic Society Bulletin, vol. 67, no. 4, pp. 763–770, 1988.
View at: Google Scholar
S. L. Swartz, E. Breval, C. A. Randall, and B. H. Fox, “SrTiO₃ glass ceramics—part I Crystallization and microstructure,” Journal of Materials Science, vol. 23, no. 11, pp. 3997–4003, 1988.
View at: Publisher Site | Google Scholar
S. L. Swartz, A. S. Bhalla, L. E. Cross, and W. N. Lawless, “SrTiO₃ glass ceramics—part II dielectric properties,” Journal of Materials Science, vol. 23, no. 11, pp. 4004–4012, 1988.
View at: Publisher Site | Google Scholar
O. P. Thakur, Crystallization, microstructure and dielectric behavior of strontium titanate borosilicate glass ceramics with some additives [Ph.D. thesis], Banaras Hindu University Varanasi, Varanasi, India, 1998.
O. P. Thakur, D. Kumar, O. M. Parkash, and L. Pandey, “Crystallization and microstructural behaviour of strontium titanate borosilicate glass ceramics with Bi₂O₃ addition,” Bulletin of Materials Science, vol. 20, no. 1, pp. 67–77, 1997.
View at: Google Scholar
O. P. Thakur, D. Kumar, O. Parkash, and L. Pandey, “Effect of K₂O addition on crystallization and microstructural behaviour of the strontium titanate-borosilicate glass-ceramic system,” Materials Letters, vol. 23, no. 4–6, pp. 253–260, 1995.
View at: Google Scholar
A. K. Sahu, D. Kumar, O. Parkash, O. P. Thakur, and C. Prakash, “Effect of K₂O/BaO ratio on crystallization, microstructure and dielectric properties of strontium titanate borosilicate glass ceramics,” Ceramics International, vol. 30, no. 3, pp. 477–483, 2004.
View at: Publisher Site | Google Scholar
C. R. Gautam, D. Kumar, and O. Parkash, “Crystallization behavior and microstructural analysis of lead-rich (Pb_1−xSr_x)TiO₃ glass ceramics containing 1 mole% La₂O,” Advance Materials Science and Engineering, vol. 2011, pp. 1–11, 2011.
View at: Google Scholar
D. Kumar, C. R. Gautam, and O. Parkash, “Preparation and dielectric characterization of ferroelectric (Pb_xSr_1−x)TiO₃ glass ceramics doped with La₂O₃,” Applied Physics Letters, vol. 89, no. 11, Article ID 112908, 2006.
View at: Publisher Site | Google Scholar
C. R. Gautam, Prabhakar Singh, O. P. Thakur, D. Kumar, and O. Parkash, “Synthesis, structure and impedance spectroscopic analysis of [(Pb_xSr_1−x)·OTiO₂]−[(2SiO₂· B₂O₃)]−7[BaO]−3[K₂O] glass ceramic system doped with La₂O₃,” Journal of Materials Science, vol. 47, pp. 6652–6664, 2012.
View at: Google Scholar
A. K. Sahu, D. Kumar, O. Parkash, O. P. Thakur, and C. Prakash, “Dielectric properties of [(Pb_1−xSr_x)O·TiO₂)]−[2SiO₂· B₂O₃]−[K₂O] glass ceramics,” British Ceramic Transactions, vol. 102, no. 4, pp. 148–152, 2003.
View at: Google Scholar
K. Uchino, E. Sadanaga, and T. Hirose, “Dependence of the crystal structure on particle size in barium titanate,” Journal of the American Ceramic Society, vol. 72, no. 8, pp. 1555–1558, 1989.
View at: Google Scholar
K. Kinoshita and A. Yamaji, “Grain-size effects on dielectric properties in barium titanate ceramics,” Journal of Applied Physics, vol. 47, no. 1, pp. 371–373, 1976.
View at: Publisher Site | Google Scholar
A. K. Sahu, D. Kumar, and O. Parkash, “Crystallisation of lead strontium titanate perovskite phase in [(Pb_1−xSr_x)O·TiO₂]−[2SiO₂· B₂O₃]−[K₂O] glass ceramics,” British Ceramic Transactions, vol. 102, no. 4, pp. 139–147, 2003.
View at: Google Scholar
J. C. Burfoot, Polar Dielectrics and Their Application, Ferroelectrics, Van Nostrand, New York, NY, USA, 1966.
B. Jaffe, W. R. Cook Jr., and H. Jaffe, Piezoelectric Ceramics, Academic Press, London, UK, 1971.
O. P. Thakur, D. Kumar, O. Parkash, and L. Pandey, “Crystallization, microstructure development and dielectric behaviour of glass ceramics in the system [SrO ·TiO₂]−[2SiO₂· B₂O₃]−La₂O₃,” Journal of Materials Science, vol. 37, no. 12, pp. 2597–2606, 2002.
View at: Publisher Site | Google Scholar
F. D. Morrison, D. C. Sinclair, and A. R. West, “Electrical and structural characteristics of lanthanum-doped barium titanate ceramics,” Journal of Applied Physics, vol. 86, no. 11, pp. 6355–6366, 1999.
View at: Google Scholar
C. R. Gautam, D. Kumar, and O. Parkash, “Dielectric and impedance spectroscopic studies of (Sr_1−xPb_x)TiO₃ glass ceramics with addition of Nb₂O₅,” Bulletin of Materials Science, vol. 34, pp. 1–7, 2011.
View at: Google Scholar
C. R. Gautam, D. Kumar, P. Singh, and O. Parkash, “Study of impedance spectroscopy of ferroelectric (Pb Sr)TiO₃glass ceramic system with addition of La₂O₃,” ISRN Spectroscopy, vol. 2012, pp. 1–11, 2012.
View at: Google Scholar

Copyright

Copyright © 2013 C. R. Gautam et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1508

Downloads

996

Citations