Journal of Chaos

Volume 2014 (2014), Article ID 429809, 15 pages

http://dx.doi.org/10.1155/2014/429809

## Theoretical Analysis and Adaptive Synchronization of a 4D Hyperchaotic Oscillator

^{1}Laboratoire de Mécanique et de Modélisation des Systèmes Physiques (L2MSP), Faculty of Science, University of Dschang, P.O. Box 69 Dschang, Cameroon^{2}Laboratoire d’Electronique et de Traitement de Signal (LETS), Faculty of Science, University of Dschang, P.O. Box 67 Dschang, Cameroon^{3}Laboratoire d’Automatique et Informatique Appliquée (LAIA), IUT-FV Bandjoun, University of Dschang, P.O. Box 67 Dschang, Cameroon

Received 31 October 2013; Accepted 14 January 2014; Published 27 February 2014

Academic Editor: Qingdu Li

Copyright © 2014 T. Fonzin Fozin et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

#### Abstract

We propose a new mathematical model of the TNC oscillator and study its impact on the dynamical properties of the oscillator subjected to an exponential nonlinearity. We establish the existence of hyperchaotic behavior in the system through theoretical analysis and by exploiting electronic circuit experiments. The obtained numerical results are found to be in good agreement with experimental observations. Moreover, the new technique on adaptive control theory is used on our model and it is rigorously proven that the adaptive synchronization can be achieved for hyperchaotic systems with uncertain parameters.

#### 1. Introduction

Over the last four decades, an increasing interest has been shown on chaotic systems with higher dimensional attractors known as hyperchaotic. The interest for hyperchaotic dynamics is justified by the rapid development of new techniques in various areas of physics such as nonlinear circuits [1–6], complex system studies [7, 8], laser dynamics [9–11], secure communication [12, 13], and synchronization [14–21]. Hyperchaotic systems are usually classified as chaotic systems with more than one positive Lyapunov exponent, indicating that the chaotic dynamics of the systems are expanded in some directions but rapidly shrink in other directions, which significantly increase the system’s orbital degree or disorder and randomness. Those systems are suitable for engineering application such as secure communications [12–14, 19, 20, 22]. In fact, in 1995, Pérez and Cerdeira [23] have shown that by masking signals with simple chaos with only one Lyapunov exponent does not provide high level of security. Hence, the use of more complex hyperchaotic signals is a straightforward way to overcome this limitation because of their increased randomness and higher unpredictability [24]. Therefore the dynamical behavior of several hyperchaotic electronic circuits has been studied [1, 2, 4–6, 10, 11, 25–27]. Within these, TNC oscillator [2] retains our attention. Indeed, it is extremely simple and provides a powerful tool for understanding the inherent architectures and dynamical behavior of hyperchaotic oscillator as well as their use as chaotic carriers in practical secure communication. Its synchronization and dynamics have been studied using a piecewise linear (PWL) model [4, 28]. Moreover, Peng et al. in [14], address the synchronization of hyperchaotic oscillators using a scalar transmitted signal. Furthermore, this scalar synchronization does not require either the computation of the Lyapunov exponent or initial conditions belonging to the same basin of attraction. For a possible use of hyperchaotic behavior in secure communication, the synchronization of hyperchaotic systems via a single dynamical variable is demonstrated [20, 29, 30]. In 2001, Miller and Grassi [19] described an experimental realization of observer-based hyperchaos synchronization using the TNC oscillator [31]. X. Wang and Y. Wang in [29] deal with the synchronization of uncertain hyperchaotic and chaotic systems by adaptive control using the TNC hyperchaotic oscillator as the master and the Rössler oscillator as the slave. However, the aforementioned analysis is performed based on the piecewise linear model of the system. Furthermore, to our knowledge, no design tool exist that may be exploited for design purposes of a Tamasevicius oscillator built by Grassi and Mascolo [4]. In fact, the PWL model represents only a first-order approximation of the reality and therefore may give rise to different types of bifurcation compared to those exhibits by the real oscillator. Moreover, Kengne et al. [32, 33] derive smooth mathematical model instead of PWL to perform the analysis of the two-stage Colpitts oscillator and the improved Colpitts oscillator. They also synchronize those coupled oscillators (with smooth mathematical model) using nonlinear state observers. Using the same concept, we propose in this paper a new smooth (exponential) mathematical model to investigate the nonlinear dynamics of the TNC oscillator. We address two key issues. The first is to point out both theoretical and experimental tools, which may be exploited for design and control purposes. The second is to complete the results obtained so far by deriving a mathematical model from which a systematic and methodological analysis of the nonlinear dynamics of the oscillator is carried out helping to point out some unknown and striking behavior of the TNC oscillator.

The organization of the paper is as follows. Section 2 deals with the modeling process. The electronic structure of the oscillator is presented and the appropriate mathematical model is derived to describe the dynamic behavior of the oscillator. The stability analysis of the equilibrium point and local bifurcation is presented in Section 3. The evolution process analysis by means of Lyapunov exponent spectrum, bifurcation diagram, and phase portraits is investigated in Section 4, where numerical simulations studies are given. In Section 5, an experimental study is carried out. The corresponding electronic circuit is implemented, exhibiting experimental chaotic attractors in accord with numerical simulations which serves to validate the model derived in this work. Section 6 considers the synchronization of such type of oscillators. By exploiting recent results on adaptive control theory, a controller is designed that combines the synchronization of two one-way coupled systems and the estimation of unknown parameters of the drive system. Finally the summary of the results is given in Section 7.

#### 2. Circuit Description and Mathematical Model

##### 2.1. Circuit Description

The model under consideration is the electronic oscillator of the Tamasevicius, Namajuas, and Cenys (TNC) given by Figure 1(a). It consists of a combined parallel-series *LC* circuit (namely, ), a single operational amplifier (op amp) with feedback resistors implementing both the negative impedance (NIC) and the output amplifier for the oscillator with a diode. This diode is the nonlinear device responsible for the hyperchaotic behavior of the oscillator. One should note that as the op amp operates in the linear region for , the input impedance of the NIC satisfies and the output obeys .

##### 2.2. Mathematical Model

This subsection introduces the new mathematical model of the TNC oscillator by considering the following hypotheses. Firstly, we assume that all capacitors, inductors, and resistors of the oscillator network are linear. Secondly, the current-voltage (*I-V*) characteristic of the diode is modeled with an exponential function (Figure 1(b)) [34] as yields in
in which is the voltage drop across the diode, represents the saturation current of the junction, stands for the ideality factor (), and is the thermal voltage wherein is the Boltzmann constant, the absolute temperature expressed in Kelvin, and the electron charge. Let us note that at room temperature (300 K), we have . If we denote by the current flowing through the inductor and the voltage across capacitor , the Kirchhoff’s electric circuit laws can be applied on Figure 1(a) to obtain the upcoming set of autonomous differential equations describing the dynamics of the TNC hyperchaotic oscillator:

where the diode current is defined by (1). In contrast to previous literature [2, 4, 31] based on PWL models of the TNC oscillator, the exponential model is considered in this paper. Indeed, the PWL model is only its first-order approximation and can approximately match only over a limited region (Figure 1(b)) and, thus, may exhibit different types of bifurcation compared to the exponential model as previously mentioned. Furthermore, owing to the fact that a smooth mathematical model is more tractable both analytically and numerically, it may be exploited to obtained exact bifurcation structures occurring in the real TNC hyperchaotic oscillator circuit. It is worth mentioning that the bifurcation diagrams are very useful for design purpose as they allow the selection of the right parameters settings giving rise to a regular or erratic behavior (hyperchaotic mode of operation). For computer simulation, we normalize the state equations (2a)–(2d) by considering the following rescaled variables and parameters:

Therefore, we obtain the upcoming smooth normalized fourth-order differential equations: with

where the dots denote differentiation with respect to (renamed as t in the new scale without loss of generality). System (4a)–(4d) present only one nonlinear term and one state variable (namely, ) is involved in exponential function. The presence of such exponential nonlinearity implies the nonsymmetry of our model. Therefore, the system cannot support symmetric orbits.

#### 3. Stationary Point and Its Nature

The notion of fixed points in the state space plays a crucial role in understanding the dynamics of nonlinear systems. The equilibria of the system (4a)–(4d) can be calculated by solving the following algebraic equations simultaneously:

Computation of (5a)–(5d) shows that the origin is the only equilibrium point of the system. By linearizing the system at that equilibrium point, the following Jacobean matrix is obtained:

Then, the eigenvalues associated with this matrix are obtained by solving the following characteristic equation: with

For the chosen parameters as , , , ,and the eigenvalues solutions of the characteristic equations (7) computed using MATHEMATICA software package are and . Since the eigenvalues are complex conjugate with some positive real parts, the equilibrium point is an unstable saddle focus. Physically, this result supports the fact that the oscillator can oscillate chaotically and excludes the existence of stable fixed point motion in the system.

#### 4. Bifurcation Analysis

In order to define different routes/cascades to chaos in our model, system (4a)–(4d) is solved numerically through the fourth-order Runge-Kutta integration algorithm. For each set of parameters used in this work, the time step is always and the simulations are done with variables and constant parameters in extended mode. For each case, the system (4a)–(4e) is integrated for a sufficiently long time and the transient is discarded. Here, two indicators are combined to identify the type of transition which leads to chaos. The first one deals with the bifurcation diagram and the second is related to the Lyapunov exponent’s spectra. According to Wolf et al. [35] method, the dynamics of the nonlinear system (4a)–(4e) can be classified in terms of the Lyapunov exponents as(1)for an equilibrium point, ;(2)for a limit cycle (periodic orbits), ;(3)for 2-torus (quasiperiodic orbits), ;(4)for 3-torus, ;(5)for a chaotic orbits, ;(6)for hyperchaotic orbits, ;

In the next two subsections, the evolution process of the system is analyzed precisely by the means of the Lyapunov exponent’s spectrum, bifurcation diagrams, and phase portraits when varying the parameters and in system (4a)–(4e).

##### 4.1. Influence of with Fix

When the control parameter varies in the range , the graph of the bifurcation diagrams and its corresponding Lyapunov exponent spectrum are depicted, respectively, in Figures 2 and 3. Each bifurcation diagram is obtained by plotting the local maxima of the related state variable in terms of the control state parameter. In the light of Figures 2 and 3, the following scenarios emerge when monitoring the control parameter : periodic quasiperiodic chaos hyperchaos chaos periodic hyperchaos periodic hyperchaos. In other word, they are many windows of hyperchaotic behavior with respect to the control parameter . Also, in contrast with the traditional approach which consists of plotting the bifurcation diagram of a single state variable, we have plotted the bifurcation diagram of all the state variables because of the nonuniformity observed between those diagrams. In fact, it can be seen that in the periodic windows, each state variable cycle has a different frequency. However, all state variables share common bifurcation point in terms of the control parameter. In particular, a good coincidence is observed between band of chaos and windows of regular behavior within those diagrams.

Moreover, for the set of parameters of Figure 2, various numerical computations of the phase space trajectories of the system (4a)–(4e) are obtained (Figure 4) confirming transitions to hyperchaos. Those curves represent the phase portraits and their corresponding frequency spectrum computed for some discrete values of : periodic oscillations torus state periodic oscillations chaotic oscillations hyperchaotic dynamics. This scenario is in conformity with the bifurcation diagram of Figure 2.

One should note that some new periodic () windows and some routes to chaos were only observed by using the exponential model of the diode instead of PWL model which is only its first approximation. The simulation results of the model proposed in [2] for exponential and piecewise-linear models are depicted in bifurcation diagram of Figure 5. The observe differences are mainly due to the poor PWL approximation of the exponential characteristic (Figure 1(b)). On the other hand, the nonsmooth nature of the piecewise-linear model of the diode can be responsible for the different bifurcation structure exhibited by our model and the one proposed in [2] as their *I-V* characteristics are not matching perfectly.

##### 4.2. Influence of with Fix

As can be seen from the bifurcation diagram (Figure 6) and the Lyapunov exponents spectrum (Figure 7), the system (4a)–(4e) can be hyperchaotic, chaotic, and periodic when varying in the range . By observing Figures 3 and 7, it appears that the hyperchaotic range is much wider for variation than when varies.

A better understanding of the transition from regular oscillations to hyperchaos could be used to achieve more effective control of chaos and also provide some novel ways of the design using such oscillators.

Although the bifurcation analysis was restricted in this work on the effects of parameters and , it is worth mentioning that any other parameters which appear in the characteristic equation could serve as a bifurcation control parameter for the TNC system.

#### 5. Experimental Study

Due to the real-time character of its results, compared to the problems of transient phase duration and numerical instabilities or time steps inherent to numerical simulations, experimental study appears as a complementary technique to the methods mentioned above. Moreover, it is of interest to evaluate the influences of the simplifying process on the real behavior of the oscillator.

##### 5.1. Design of the Experimental Circuit

The circuit diagram of the TNC oscillator depicted in Figure 8 consists of an op. amp (TL082) powered by a symmetric DC voltage supply, inductors () implemented using gyrators [36], capacitors (), resistors (, , and ), and a diode () ( and at ) in series with its resistor . In the diagram of Figure 8, the inductors are expressed in terms of the circuit components as follows:

For the following set of the parameters , , , , and and , , , , and , we determine the corresponding values of the inductances: and . It is worth mentioning that the use of gyrators instead of real inductors is advantageous since it becomes possible to monitor the values of inductances over a wide range by simply adjust a resistor. Therefore, inductors ( and/or ) could also be used as a bifurcation parameters (by varying and/or ). The other circuit components are taken as , , , and .

##### 5.2. Experimental Results

Now, we wish to analyze the effects of the damping resistor (that deals with the control parameter ) on the dynamics of the TNC oscillator. The experimental results are obtained by slowly adjusting and plotted phase space trajectories using a dual trace analog oscilloscope (HAMEG HM-203_{−5}) in the mode. When monitoring the resistor , it is found that the experimental oscillator circuit exhibits various types of bifurcation. Indeed, for , a limit cycle behavior is observed. But when decreases gradually, the following transition is obtained: periodic oscillations torus state chaotic oscillations hyperchaotic oscillations periodic oscillations hyperchaotic oscillations. The state is the voltage across the capacitor as in practice it is difficult to measure through an oscilloscope the current. Some periodic windows appearing between the chaotic and hyperchaotic regimes are also noted and were only figured out numerically () using the exponential model of the diode. Figure 9 presents the result of the experimental real investigation of the TNC oscillator. From those plots, one should note that the real circuit exhibits the same bifurcation scenarios observed using theoretical methods. These results also give a good agreement between numerical and experimental results and, thereby, can be considered to validate the mathematical model (exponential model) proposed in this paper to describe the dynamic behavior of the TNC hyperchaotic oscillator.

#### 6. Synchronization Study

In this section, we investigate the chaos synchronization of the model (4a)–(4e) with the realistic assumption of parameters uncertainty. In fact, the complex behaviors of hyperchaotic systems are believed to have much wider applications. However, they are few discussions in the literature when the parameters of the system are unknown. Moreover, in practice, some or all the parameters of the system cannot be exactly known a priori (due to temperature, external electric and magnetic fields, etc.) or may be time varying and/or inaccessible to direct measurements. Therefore, the synchronization of two uncertain chaotic systems is essential [37–42].

##### 6.1. Design of the Slave System

For our analysis, it is assumed that the state variables of the drive system are all accessible to measurements and the system parameters are unknown.

Theorem 1. *Let the system (4a)–(4e) be written in the following form:*

*in which we have*

*with **. Then the corresponding response system **which** is given by**can synchronize with the master system (10a) and (10b), with the controller ** defined as *

*where **, **, and ** are the estimation of the corresponding parameters of the drive system (10a) and (10b).*

*Proof. *The error of the dynamical system can be rewritten as

At this level, we consider the following Lyapunov function candidate:
whose time derivative along the trajectory is given by

Owing to the result (15), we conclude that is a Lyapunov function of the error system and that (13) is stable at the origin, traducing the fact that are bounded.

##### 6.2. Numerical Verification

Referring to Theorem 1 above, the response system is described by the following sets of first-order differential equations:

The numerical computations of (16a)–(16g) are performed using the fourth-order Runge-Kutta integration algorithm with a time step of . The initial conditions on parameters are taken as , , and . We select the parameter of the drive system as , , and to ensure a hyperchaotic behavior. Numerical results are shown on Figures 10 and 11. From those graphs, it can be noted that the hyperchaotic synchronization and the unknown parameters identification are achieved simultaneously after a short transient time. Obviously, this perfect synchronization may be exploited in secure communication using the technique of parameter modulation/estimation [37–39] as the system can be designed and implemented at any given frequency band depending on the values of circuit components.

#### 7. Conclusion

In this paper, we have built a new mathematical model based on the exponential nonlinearity to examine the behavior of a simple 4D hyperchaotic electronic oscillator. This exponential model takes advantage of the PWL approximation as it provides a close form description of the oscillator’s dynamics. Dynamics of the system subjected to this exponential model have been analyzed both through bifurcation diagrams, Lyapunov exponents, phase portraits, and routes to chaos. By monitoring the parameters, the system has exhibited many phase portraits with different shapes from periodic to hyperchaotic oscillations. A real physical prototype was designed and implemented on a bread board to study the dynamics of our model. Theoretical and experimental results obtained have been compared and a very good agreement was observed. In the context of the application to secure communication, the synchronization of coupled hyperchaotic system of the model with uncertain parameters has also been studied using the recent results on adaptive control theory.

#### Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

#### References

- T. Matsumoto, L. O. Chua, and K. Kobayashi, “Hyperchaos: laboratory experiment and numerical confirmation,”
*IEEE Transactions on Circuits and Systems*, vol. 33, no. 11, pp. 1143–1147, 1986. View at Google Scholar · View at Scopus - A. Tamaševičius, A. Namajunas, and A. Čenys, “Simple 4D chaotic oscillator,”
*Electronics Letters*, vol. 32, no. 11, pp. 957–958, 1996. View at Google Scholar · View at Scopus - A. Tamaševičius, A. Čenys, G. Mykolaitis, A. Namajunas, and E. Lindberg, “Hyperchaotic oscillator with gyrators,”
*Electronics Letters*, vol. 33, no. 7, pp. 542–544, 1997. View at Google Scholar · View at Scopus - G. Grassi and S. Mascolo, “Synchronisation of hyperchaotic oscillators using a scalar signal,”
*Electronics Letters*, vol. 34, no. 5, pp. 424–425, 1998. View at Google Scholar · View at Scopus - C. P. Silva and A. M. Young, “Introduction to chaos-based communications and signal processing,” in
*Proceedings of the 2000 IEEE Aerospace Conference*, vol. 1, pp. 279–299, March 2000. View at Scopus - B. Cannas and S. Cincotti, “Hyperchaotic behaviour of two bi-directionally coupled Chua's circuits,”
*International Journal of Circuit Theory and Applications*, vol. 30, no. 6, pp. 625–637, 2002. View at Publisher · View at Google Scholar · View at Scopus - N. Goldenfeld and L. P. Kadanoff, “Simple lessons from complexity,”
*Science*, vol. 284, no. 5411, pp. 87–89, 1999. View at Publisher · View at Google Scholar · View at Scopus - R. Vicente, J. Daudén, P. Colet, and R. Toral, “Analysis and characterization of the hyperchaos generated by a semiconductor laser subject to a delayed feedback loop,”
*IEEE Journal of Quantum Electronics*, vol. 41, no. 4, pp. 541–548, 2005. View at Publisher · View at Google Scholar · View at Scopus - R. Stoop, J. Peinke, J. Parisi, B. Röhricht, and R. P. Huebener, “A p-Ge semiconductor experiment showing chaos and hyperchaos,”
*Physica D*, vol. 35, no. 3, pp. 425–435, 1989. View at Google Scholar · View at Scopus - Y. Li, W. K. S. Tang, and G. Chen, “Hyperchaos evolved from the generalized Lorenz equation,”
*International Journal of Circuit Theory and Applications*, vol. 33, no. 4, pp. 235–251, 2005. View at Publisher · View at Google Scholar · View at Scopus - Y. Li, X. Liu, G. Chen, and X. Liao, “A new hyperchaotic Lorenz-type system: generation, analysis, and implementation,”
*International Journal of Circuit Theory and Applications*, vol. 39, no. 8, pp. 865–879, 2011. View at Publisher · View at Google Scholar · View at Scopus - C. K. Duan and S. S. Yang, “Synchronizing hyperchaos with a scalar signal by parameter controlling,”
*Physics Letters A*, vol. 229, no. 3, pp. 151–155, 1997. View at Google Scholar · View at Scopus - Z. Liu, C. Liu, M. Ho, Y. Hung, T. Hsu, and I. Jiang, “Synchronization of uncertain hyperchaotic and chaotic systems by adaptive control,”
*International Journal of Bifurcation and Chaos*, vol. 18, no. 12, pp. 3731–3736, 2008. View at Publisher · View at Google Scholar · View at Scopus - J. H. Peng, E. J. Ding, M. Ding, and W. Yang, “Synchronizing hyperchaos with a scalar transmitted signal,”
*Physical Review Letters*, vol. 76, no. 6, pp. 904–907, 1996. View at Google Scholar · View at Scopus - A. Tamasevicius and A. Cenys, “Synchronizing hyperchaos with a single variable,”
*Physical Review E*, vol. 55, pp. 297–299, 1997. View at Google Scholar - A. Tamaševičius, A. Čenys, A. Namajunas, and G. Mykolaitis, “Synchronising hyperchaos in infinite-dimensional dynamical systems,”
*Chaos, Solitons and Fractals*, vol. 9, no. 8, pp. 1403–1408, 1999. View at Google Scholar · View at Scopus - K. Murali, A. Tamasevicius, G. Mykolaitis, A. Namajunas, and E. Lindberg, “Hyperchaos system with unstable oscillators,”
*Nonlinear Phenomenon in Complex Systems*, vol. 3, pp. 7–10, 2000. View at Google Scholar - S. Effati, J. Saberi-Nadjafi, and H. Saberi Nick, “Optimal and adaptive control for a kind of 3D chaotic and 4D hyperchaotic systems,”
*Applied Mathematical Modelling*, vol. 38, pp. 759–774, 2014. View at Google Scholar - D. A. Miller and G. Grassi, “Experimental realization of observer-based hyperchaos synchronization,”
*IEEE Transactions on Circuits and Systems I*, vol. 48, no. 3, pp. 366–374, 2001. View at Publisher · View at Google Scholar · View at Scopus - V. S. Udaltsov, J. Goedgebuer, L. Larger, and W. T. Rhodes, “Communicating with optical hyperchaos: information encryption and decryption in delayed nonlinear feedback systems,”
*Physical Review Letters*, vol. 86, no. 9, pp. 1892–1895, 2001. View at Publisher · View at Google Scholar · View at Scopus - A. Buscarino, L. Fortuna, and M. Frasca, “Experimental robust synchronization of hyperchaotic circuits,”
*Physica D*, vol. 238, no. 18, pp. 1917–1922, 2009. View at Publisher · View at Google Scholar · View at Scopus - C. C. Yang, “Adaptive single input control for synchronization of a 4D Lorenz-Stenflo chaotic system,”
*Arabian Journal for Science and Engineering*, 2013. View at Publisher · View at Google Scholar - G. Pérez and H. A. Cerdeira, “Extracting messages masked by chaos,”
*Physical Review Letters*, vol. 74, no. 11, pp. 1970–1973, 1995. View at Publisher · View at Google Scholar · View at Scopus - L. Pocora, “Hyperchaos harnessed,”
*Physics World*, vol. 9, no. 5, p. 17, 1996. View at Google Scholar · View at Scopus - G. Qi, M. A. van Wyk, B. J. van Wyk, and G. Chen, “A new hyperchaotic system and its circuit implementation,”
*Chaos, Solitons and Fractals*, vol. 40, no. 5, pp. 2544–2549, 2009. View at Publisher · View at Google Scholar · View at Scopus - L. Liu, C. Liu, and Y. Zhang, “Theoretical analysis and circuit implementation of a novel complicated hyperchaotic system,”
*Nonlinear Dynamics*, vol. 66, no. 4, pp. 707–715, 2011. View at Publisher · View at Google Scholar · View at Scopus - W. Wu, Z. Chen, and Z. Yuan, “The evolution of a novel four-dimensional autonomous system: among 3-torus, limit cycle, 2-torus, chaos and hyperchaos,”
*Chaos, Solitons and Fractals*, vol. 39, no. 5, pp. 2340–2357, 2009. View at Google Scholar · View at Scopus - G. Grassi and S. Mascolo, “Nonlinear observer design to synchronize hyperchaotic systems via a scalar signal,”
*IEEE Transactions on Circuits and Systems I*, vol. 44, no. 10, pp. 1011–1013, 1997. View at Google Scholar · View at Scopus - X. Wang and Y. Wang, “Adaptive control for synchronization of a four-dimensional chaotic system via a single variable,”
*Nonlinear Dynamics*, vol. 65, no. 3, pp. 311–316, 2011. View at Publisher · View at Google Scholar · View at Scopus - C. Yang, “Adaptive synchronization of Lü hyperchaotic system with uncertain parameters based on single-input controller,”
*Nonlinear Dynamics*, vol. 63, no. 3, pp. 447–454, 2011. View at Publisher · View at Google Scholar · View at Scopus - A. Tamaševičius, G. Mykolaitis, A. Čenys, and A. Namajunas, “Synchronisation of 4D hyperchaotic oscillators,”
*Electronics Letters*, vol. 32, no. 17, pp. 1536–1538, 1996. View at Google Scholar · View at Scopus - J. Kengne, J. C. Chedjou, V. A. Fono, and K. Kyamakya, “On the analysis of bipolar transistor based chaotic circuits: case of a two-stage colpitts oscillator,”
*Nonlinear Dynamics*, vol. 67, no. 2, pp. 1247–1260, 2012. View at Publisher · View at Google Scholar · View at Scopus - J. Kengne, J. C. Chedjou, G. Kenne, and K. Kyamakya, “Dynamical properties and chaos synchronization of improved Colpitts oscillators,”
*Communications in Nonlinear Science and Numerical Simulation*, vol. 17, no. 7, pp. 2914–2923, 2012. View at Publisher · View at Google Scholar · View at Scopus - A. S. Sedra and C. S. Kenneth,
*Microelectronic Circuits*, Oxford University Press, New York, NY, USA, 5th edition, 2003. - A. Wolf, J. B. Swift, H. L. Swinney, and J. A. Vastano, “Determining Lyapunov exponents from a time series,”
*Physica D*, vol. 16, no. 3, pp. 285–317, 1985. View at Google Scholar · View at Scopus - K. Giannakopoulos, T. Deliyannis, and J. Hadjidemetriou, “Means for detecting chaos and hyperchaos in nonlinear electronic circuits,” in
*Proceedings of the 14th IEEE International Conference on Digital Signal Processing*, pp. 951–954, 2002. - H. B. Fotsin and P. Woafo, “Adaptive synchronization of a modified and uncertain chaotic Van der Pol-Duffing oscillator based on parameter identification,”
*Chaos, Solitons and Fractals*, vol. 24, no. 5, pp. 1363–1371, 2005. View at Publisher · View at Google Scholar · View at Scopus - Y. Xu, W. Zhou, J. Fang, and W. Sun, “Adaptive bidirectionally coupled synchronization of chaotic systems with unknown parameters,”
*Nonlinear Dynamics*, vol. 66, no. 1-2, pp. 67–76, 2011. View at Publisher · View at Google Scholar · View at Scopus - H. Adloo and M. Roopaei, “Review article on adaptive synchronization of chaotic systems with unknown parameters,”
*Nonlinear Dynamics*, vol. 65, no. 1-2, pp. 141–159, 2011. View at Publisher · View at Google Scholar · View at Scopus - S. Vaidyanathan, “Analysis, control and synchronization of hyperchaotic Zhou system via adaptive control,”
*Advances in Computing and Information Technology*, vol. 117, pp. 1–10, 2013. View at Google Scholar - X. Zhou, L. Xiong, and X. Cai, “Adaptive switched generalized function projective synchronization between two hyperchaotic systems with unknown parameters,”
*Entropy*, vol. 16, pp. 377–388, 2014. View at Google Scholar - X. Zhou, Z. Fan, D. Zhou, and X. Cai, “Passivity-based adaptive hybrid synchronization of a new hyperchaotic system with uncertain parameters,”
*The Scientific World Journal*, vol. 2012, Article ID 920170, 6 pages, 2012. View at Publisher · View at Google Scholar