Table of Contents Author Guidelines Submit a Manuscript
Advances in Civil Engineering
Volume 2018, Article ID 1634702, 10 pages
https://doi.org/10.1155/2018/1634702
Research Article

A New Rate-Dependent Constitutive Model of Superelastic Shape Memory Alloys and Its Simple Application in a Special Truss Moment Frame Simulation

Department of Civil Engineering, University of Thessaly, Volos 38334, Greece

Correspondence should be addressed to Dimitrios S. Sophianopoulos; rg.htu.vic@fosmid

Received 17 June 2018; Revised 9 August 2018; Accepted 13 August 2018; Published 17 September 2018

Academic Editor: Rosario Montuori

Copyright © 2018 Maria I. Ntina and Dimitrios S. Sophianopoulos. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. G. Song, M. Ma, and H.-N. Li, “Applications of shape memory alloys in civil structures,” Engineering Structures, vol. 28, no. 9, pp. 1266–1274, 2006. View at Publisher · View at Google Scholar · View at Scopus
  2. R. Paiva and M. A. Savi, “An overview of constitutive models for shape memory alloys,” Mathematical Problems in Engineering, vol. 2006, Article ID 56876, 30 pages, 2006. View at Publisher · View at Google Scholar · View at Scopus
  3. H. S. Basha and S. C. Goel, “Special truss moment frames with Vierendeel middle panel,” Engineering Structures, vol. 17, no. 5, pp. 352–358, 1995. View at Publisher · View at Google Scholar · View at Scopus
  4. S. H. Chao and S. C. Goel, “Performance-based plastic design of seismic resistance special truss moment frames,” Research Report UMCEE 06-03, Department of Civil and Environmental Engineering, The University of Michigan, Ann Arbor, MI, USA, May 2006.
  5. E. J. Graesser and F. A. Cozzarelli, “Multidimensional models of hysteretic material behavior for vibration analysis of shape memory alloys,” Technical Report NCEER-89-0018, State University of New York at Buffalo, Buffalo, NY, USA, 1989.
  6. D. C. Lagoudas, Shape Memory Alloys. Modeling and Engineering Applications, Springer, New York, NY, USA, 2008.
  7. W. J. Buehler, J. V. Gilfrich, and R. C. Wiley, “Effect of low-temperature phase changes on the mechanical properties of alloys near composition of NiTi,” Journal of Applied Physics, vol. 34, no. 5, pp. 1475–1477, 1963. View at Publisher · View at Google Scholar · View at Scopus
  8. H. Özdemir, “Nonlinear transient dynamic analysis of yielding structures,” Ph.D. dissertation, University of California, Berkeley, CA, USA, 1976.
  9. K. Wilde, P. Gardoni, and Y Fujino, “Base isolation system with shape memory alloy device for elevated highway bridges,” Engineering Structures, vol. 22, no. 3, pp. 222–229, 2000. View at Publisher · View at Google Scholar · View at Scopus
  10. F. Auricchio, D. Fugazza, and R. DesRoches, “A 1D rate-dependent viscous constitutive model for shape-memory alloys: formulation and comparison with experimental data,” Smart Materials and Structures, vol. 16, no. 1, pp. 39–50, 2007. View at Publisher · View at Google Scholar · View at Scopus
  11. R. DesRoches, J. McCormick, and M. Delemont, “Cyclic response of superelastic shape memory alloy wires and bars,” Journal of Structural Engineering, vol. 130, no. 1, pp. 38–46, 2004. View at Publisher · View at Google Scholar · View at Scopus
  12. S. C. Goel and A. M. Itani, “Seismic-resistant special truss-moment frames,” Journal of Structural Engineering, vol. 120, no. 6, pp. 1781–1797, 1994. View at Publisher · View at Google Scholar · View at Scopus
  13. ANSI, ANSI/AISC 341-16: Seismic Provisions for Structural Steel Buildings, American Institute of Steel Construction, Chicago, IL, USA, 2016.
  14. A. Longo, R. Montuori, and V. Piluso, “Theory of plastic mechanism control of dissipative truss moment frames,” Engineering Structures, vol. 37, pp. 63–75, 2012. View at Publisher · View at Google Scholar · View at Scopus
  15. A. Longo, R. Montuori, and V. Piluso, “Failure mode control and seismic response of dissipative truss moment frames,” Journal of Structural Engineering, vol. 138, no. 11, pp. 1388–1397, 2012. View at Publisher · View at Google Scholar · View at Scopus
  16. R. Montuori, E. Nastri, and V. Piluso, “Advances in theory of plastic mechanism control: closed- form solution for MR-frames,” Earthquake Engineering & Structural Dynamics, vol. 44, no. 7, pp. 1035–1044, 2015. View at Publisher · View at Google Scholar · View at Scopus
  17. D. Cassiano, M. D’Aniello, C. Rebelo, R. Landolfo, and L. Simoes da Silva, “Influence of seismic design rules on the robustness of steel moment resisting frames,” Steel and Composite Structures, vol. 21, no. 3, pp. 479–500, 2016. View at Publisher · View at Google Scholar · View at Scopus
  18. A. Techini, M. D’Aniello, C. Rebelo, R. Landolfo, L. Simoes da Silva, and L. Lima, “Seismic performance of dual-steel moment resisting frames,” Journal of Constructional Steel Research, vol. 101, pp. 437–454, 2014. View at Publisher · View at Google Scholar · View at Scopus
  19. M. Ntina, D. Sophianopoulos, and P. Tsopelas, “Development of a 2-dof model simulating the dynamic response of special truss moment frames with shape memory alloy bars as dissipation devices in the special segment,” in Proceedings of Eurosteel 2017, Ernst & Sohn, Copenhagen, Denmark, September 2017.