Research Article
Comparison of Uplift Capacity and Nonlinear Failure Surfaces of Single-Belled Anchor in Homogeneous and Layered Sand Deposits
Table 2
Detail geometry of the 3D model and 2D panel and their designations in homogeneous sand deposit (SI).
| | α (°) | Ds or Ts | Db or Tb | Db/Ds or Tb/Ts | 3D model identifications | 2D panel identifications | L/Db or L/Ts | L (mm) | 3D model designations in SI | 2D panel designations in SII/SI | | (i) | (ii) | (iii) | (iv) | (v) | (vi) | (vii) | (viii) | (ix) | (x) |
| | 45 | 26 | 92 | 0.28 | 3D:45-0.28 | 2D:45-0.28 | 276 | 3 | 3D:45-0.28-3-(SI) | 2D:45-0.28-3-(SI) | | 368 | 4 | 3D:45-0.28-4-(SI) | 2D:45-0.28-4-(SI) | | 460 | 5 | 3D:45-0.28-5-(SI) | 2D:45-0.28-5-(SI) |
| | 45 | 26 | 80 | 0.33 | 3D:45-0.33 | 2D:45-0.33 | 240 | 3 | 3D:45-0.33-3-(SI) | 2D:45-0.33-3-(SI) | | 320 | 4 | 3D:45-0.33-4-(SI) | 2D:45-0.33-4-(SI) | | 400 | 5 | 3D:45-0.33-5-(SI) | 2D:45-0.33-5-(SI) |
| | 45 | 26 | 68 | 0.38 | 3D:45-0.38 | 2D:45-0.38 | 204 | 3 | 3D:45-0.38-3-(SI) | 2D:45-0.38-3-(SI) | | 272 | 4 | 3D:45-0.38-4-(SI) | 2D:45-0.38-4-(SI) | | 340 | 5 | 3D:45-0.38-5-(SI) | 2D:45-0.38-5-(SI) |
| | 45 | 26 | 56 | 0.46 | 3D:45-0.46 | 2D:45-0.46 | 168 | 3 | 3D:45-0.46-3-(SI) | 2D:45-0.46-3-(SI) | | 224 | 4 | 3D:45-0.46-4-(SI) | 2D:45-0.46-4-(SI) | | 280 | 5 | 3D:45-0.46-5-(SI) | 2D:45-0.46-5-(SI) |
| | 63 | 26 | 92 | 0.28 | 3D:63-0.28 | 2D:63-0.28 | 276 | 3 | 3D:63-0.28-3-(SI) | 2D:63-0.28-3-(SI) | | 368 | 4 | 3D:63-0.28-4-(SI) | 2D:63-0.28-4-(SI) | | 460 | 5 | 3D:63-0.28-5-(SI) | 2D:63-0.28-5-(SI) |
| | 63 | 26 | 80 | 0.33 | 3D:63-0.33 | 2D:63-0.33 | 240 | 3 | 3D:63-0.33-3-(SI) | 2D:63-0.33-3-(SI) | | 320 | 4 | 3D:63-0.33-4-(SI) | 2D:63-0.33-4-(SI) | | 400 | 5 | 3D:63-0.33-5-(SI) | 2D:63-0.33-5-(SI) |
| | 63 | 26 | 68 | 0.38 | 3D:63-0.38 | 2D:63-0.38 | 204 | 3 | 3D:63-0.38-3-(SI) | 2D:63-0.38-3-(SI) | | 272 | 4 | 3D:63-0.38-4-(SI) | 2D:63-0.38-4-(SI) | | 340 | 5 | 3D:63-0.38-5-(SI) | 2D:63-0.38-5-(SI) |
| | 63 | 26 | 56 | 0.46 | 3D:63-0.46 | 2D:63-0.46 | 168 | 3 | 3D:63-0.46-3-(SI) | 2D:63-0.46-3-(SI) | | 224 | 4 | 3D:63-0.46-4-(SI) | 2D:63-0.46-4-(SI) | | 280 | 5 | 3D:63-0.46-5-(SI) | 2D:63-0.46-5-(SI) |
| | 72 | 26 | 92 | 0.28 | 3D:72-0.28 | 2D:72-0.28 | 276 | 3 | 3D:72-0.28-3-(SI) | 2D:72-0.28-3-(SI) | | 368 | 4 | 3D:72-0.28-4-(SI) | 2D:72-0.28-4-(SI) | | 460 | 5 | 3D:72-0.28-5-(SI) | 2D:72-0.28-5-(SI) |
| | 72 | 26 | 80 | 0.33 | 3D:72-0.33 | 2D:72-0.3 | 240 | 3 | 3D:72-0.33-3-(SI) | 2D:72-0.33-3-(SI) | | 320 | 4 | 3D:72-0.33-4-(SI) | 2D:72-0.33-4-(SI) | | 400 | 5 | 3D:72-0.33-5-(SI) | 2D:72-0.33-5-(SI) |
| | 72 | 26 | 68 | 0.38 | 3D:72-0.38 | 2D:72-0.38 | 204 | 3 | 3D:72-0.38-3-(SI) | 2D:72-0.38-3-(SI) | | 272 | 4 | 3D:72-0.38-4-(SI) | 2D:72-0.38-4-(SI) | | 340 | 5 | 3D:72-0.38-5-(SI) | 2D:72-0.38-5-(SI) |
| | 72 | 26 | 56 | 0.46 | 3D:72-0.46 | 2D:72-0.46 | 168 | 3 | 3D:72-0.46-3-(SI) | 2D:72-0.46-3-(SI) | | 224 | 4 | 3D:72-0.46-4-(SI) | 2D:72-0.46-4-(SI) | | 280 | 5 | 3D:72-0.46-5-(SI) | 2D:72-0.46-5-(SI) |
|
|
