Abstract

Dye-sensitized solar cells (DSSCs) hold great promise in the pursuit of reliable and cheap renewable energy. In this work, tin-doped indium oxide (ITO)-TiO2 core-shell nanostructures are used as the photoanode for DSSCs. High-density, vertically aligned ITO nanowires are grown via a thermal evaporation method and TiO2 is coated on nanowire surfaces via TiCl4 treatment. It is found that high TiO2 annealing temperatures increase the crystallinity of TiO2 shell and suppress electron recombination in the core-shell nanostructures. High annealing temperatures also decrease dye loading. The highest efficiency of 3.39% is achieved at a TiO2 annealing temperature of 500°C. When HfO2 blocking layers are inserted between the core and shell of the nanowire, device efficiency is further increased to 5.83%, which is attributed to further suppression of electron recombination from ITO to the electrolyte. Open-circuit voltage decay (OCVD) measurements show that the electron lifetime increases by more than an order of magnitude upon HfO2 insertion. ITO-TiO2 core-shell nanostructures with HfO2 blocking layers are promising photoanodes for DSSCs.

1. Introduction

Dye-sensitized solar cells (DSSCs) have attracted a lot of attention in recent years due to their promising properties, including low cost, ease of fabrication, and flexibility in material selection [1, 2]. A DSSC typically consists of a dyed TiO2-based photoanode, a platinized counter electrode, and a liquid electrolyte containing a redox couple (such as ). Under illumination, electrons in the dye are excited from the HOMO to the LUMO level. These electrons are then injected into the conduction band of TiO2. A transparent conduction oxide (TCO) collects these electrons, which pass through the external circuit and generate power.

TiO2 nanoparticle-based thin films are conventionally used as the photoanode of DSSCs. TiO2 nanoparticles provide large surface area for maximum dye attachment, which enables high current densities and high efficiencies. However, electrons in TiO2 nanoparticles are transported via random walk [35], which limits the effective thickness of the TiO2 thin film to be ~10 μm [6]. The slow kinetics also leads to major electron losses via electron recombination from TiO2 to the electrolyte, from TiO2 to the dye, and from TCO to the electrolyte. Electron recombination is the limiting factor for increasing the efficiencies of DSSCs [7].

Core-shell nanostructures can be used to facilitate electron transport and suppress electron recombination. For instance, in ITO-TiO2 core-shell nanostructures, the accumulation of positive and negative charges in the space-charge layers in the TiO2 shell establishes an electric field [3, 6, 810], which could draw electrons in the TiO2 layer towards the ITO core during DSSC operation. The rapid transport of electrons in TiO2 could greatly suppress electron recombination from TiO2 to the electrolyte. The direct contact between the single-crystalline ITO nanowires and the current collector ensures efficient electron collection as well.

Establishing compact blocking layers in the photoanode is also an effective approach to reducing electron recombination [11]. TiO2 has a bandgap of 3.2 eV [12]; therefore, the high bandgap of HfO2 [7, 13], Al2O3 [1416], SiO2 [14, 17], and ZrO2 [18] (typically >5 eV) creates an energy barrier. This energy barrier acts as a blocking layer to electron transport that suppresses electron recombination with the electrolyte. However, the blocking layers need to be extremely thin (<a few nm) so that forward electron transport is minimally impacted.

In this study, DSSCs based on ITO-TiO2 core-shell nanostructures are investigated. Vertically aligned ITO nanowires are grown directly on ITO/glass substrates by a thermal evaporation method. Core-shell nanostructures are formed by coating the nanowires with TiO2 through TiCl4 treatment. HfO2 blocking layers are deposited on ITO nanowire surfaces by atomic layer deposition (ALD). Photovoltaic properties of devices based on these core-shell nanostructures are evaluated.

2. Experimental Section

2.1. ITO Nanowire Growth

ITO nanowires were grown using a thermal evaporation method. Tin (99.995%) and indium (99.99%) powders were mixed in a 4.5 : 10 atomic ratio by a spatula. The mixed powder was loaded into the center of a quartz tube on a quartz boat. Glass slides with a predeposited 400-nm-thick ITO thin film (Thin Film Devices, Inc., USA) were coated with a 3 nm Au film by a sputter coater (Electron Microscopy Sciences, Inc., USA). The glass slides were placed a few centimeters from the metal source. A 0.5% oxygen gas stream (balance argon) was fed into the quartz tube at a flow rate of 50 standard cubic centimeters per minute (sccm). The vacuum level in the quartz tube was maintained below 170 mTorr for successful nanowire growth. The tube furnace was heated to 750°C for 30 min and cooled down. After each growth, scanning electron microscopy (SEM) was used to examine the nanowires. All nanowires used in this work have a length of μm.

2.2. ITO-TiO2 Core-Shell Nanostructures

For maximum dye attachment, the nanowire surfaces were coated with a layer of TiO2 by TiCl4 treatment, resulting in ITO-TiO2 core-shell nanostructures. Nanowires were immersed in a 0.1 M TiCl4 solution for 8 h and this process was repeated 12 times. After coating, TiO2 was annealed at temperatures between 350 and 600°C for 1 h in air. To investigate the effect of blocking layers on device performance, a compact layer of HfO2 was deposited on nanowire surfaces by atomic layer deposition (ALD) before TiCl4 treatment. Tetrakis(dimethylamido)hafnium and H2O were the Hf and O sources for ALD, respectively. The nominal thickness of HfO2 for each ALD cycle is 0.11 nm and a total of 16 ALD cycles were performed on nanowire surfaces.

2.3. DSSC Device Fabrication

N719 dye (Dyesol) was dissolved in ethanol to make a 3 mM solution. The annealed core-shell structures were soaked in dye solution for ~14 h for dye attachment. Counter-electrode solution (CELS, Dyesol) was spin-coated on ITO/glass and annealed at 430°C for 10 min. The core-shell nanostructure photoanode and the counter electrode were held together by clips with Scotch tape as the spacer. An solution was used as the electrolyte (EL-HPE, Dyesol).

2.4. Characterization

The morphologies and length of nanowires were examined by a SEM (FEI Nova NanoSEM 430). ITO-TiO2 core-shell structures were characterized by a JEOL 2010F transmission electron microscopy (TEM). The simulated global AM 1.5 spectrum (100 mW·cm−2) for device testing was produced by a light source (XPS 200 and 16s, Solar Light Company, USA). Current-voltage (J-V) response and open-circuit voltage decay (OCVD) were recorded by a potentiostat (VersaSTAT 3, Princeton Applied Research, USA). For each type of cell, 3-4 devices were tested. OCVD measures the change of open-circuit voltage () with time after illumination was interrupted. Electron lifetime () was calculated from the slope of the decay curve [19], , where is the Boltzmann constant, T is the absolute temperature, and is the positive electron charge. Dye loading was determined by desorbing the dye in 0.1 M NaOH water/ethanol (1 : 1 v/v) solution and measuring its absorption spectrum using a Perkin-Elmer Lambda 800 UV-Vis spectrometer. The crystallinity of the TiO2 shell after annealing at different temperatures was investigated by a Renishaw inVia micro-Raman spectrometer equipped with a 785 nm laser.

3. Results and Discussion

Figure 1(a) shows the SEM image of ITO nanowires grown on ITO/glass substrate. When used as the photoanode, the vertically aligned nanowires are expected to efficiently transport electrons to the substrate where the current is collected. These nanowires have high density, which enables high dye loading and high current density during device operation. Figure 1(b) shows a TEM image of a nanowire coated with TiO2 by TiCl4 treatment. The radial electrical field in the ITO-TiO2 core-shell structures could facilitate electron transport during DSSC operation by drawing electrons to the ITO core [3, 6].

Figure 2(a) shows the - characteristics of devices without HfO2 blocking layers under illumination and Figure 2(b) at dark conditions when TiO2 was annealed between 350 and 600°C. The corresponding photovoltaic properties are listed in Table 1. It is seen that both open-circuit voltage () and short-circuit current () increase with the increase of annealing temperatures, which resulted in the highest efficiency of 3.39% when the annealing temperature for TiO2 shell was 500°C. The increase in efficiency is attributed to two reasons. (a) Higher annealing temperatures resulted in better crystallinity of the anatase TiO2 shell, as evidenced by the Raman spectra of samples annealed at different temperatures shown in Figure 3. The better crystallinity led to better conductivity and charge transport. (b) Higher annealing temperatures suppressed electron recombination from ITO to the electrolyte, as evidenced by the smaller dark current in Figure 2(b). It should be noted that when compared to conventional TiO2 nanoparticle-based DSSCs, electron recombination from TiO2 to the electrolyte in ITO-TiO2 core-shell nanostructures is minimized due to the rapid transport of electrons from TiO2 to ITO by the electric field in the TiO2 shell [3, 6].

At 600°C, although the continues to increase, the decreased dramatically, leading to a decreased device efficiency of 2.76%. The decrease of efficiency is due to the decreased dye loading (see Table 1). The amount of dye loading directly dictates the current density in DSSCs. The decreased dye loading eventually resulted in lower efficiency despite the fact that the dark current continued to decrease at 600°C, as shown in Figure 2(b).

To further improve DSSC efficiencies, compact HfO2 blocking layers were first deposited on nanowire surfaces. TiCl4 treatment was subsequently performed to form core-shell nanostructures, which were then annealed at 500°C for 1 h. J-V curves of the devices based on these structures are shown in Figure 4. Upon HfO2 insertion, the increased dramatically from 0.53 to 0.67 V. The of DSSCs is determined by the difference in Fermi level of TiO2 and that of the redox couple in the electrolyte [20]. Since the conduction band edge position for HfO2 is much higher than that for TiO2, the insertion of HfO2 between ITO and TiO2 could greatly raise the Fermi level of TiO2. Consequently, higher is seen in Figure 4(a).

The HfO2 blocking layer also greatly increased the , as shown in Figure 4(a). From Table 2, HfO2 barely affected dye loading. Therefore, the increase in is mainly attributed to the suppression of electron recombination by HfO2, as indicated by the smaller dark current in Figure 4(b). The high bandgap of HfO2 (5.9 eV versus 3.6 eV for ITO [7]) created an energy barrier that suppressed the back transfer of electrons from ITO to the electrolyte, while electrons in TiO2 could tunnel through the thin layer of HfO2 to reach ITO [1]. The axial electrical field in the TiO2 shell expected for core-shell nanowires [6] should also assist in drawing electrons to the ITO core. The higher and eventually led to an efficiency of 5.83% with HfO2 insertion, corresponding to an increase of 72% from devices without HfO2.

In order to investigate the electron transfer kinetics in DSSCs, OCVD measurements were performed and the results are shown in Figure 5. From Figure 5(a), higher TiO2 annealing temperatures resulted in slower decay, which is indicated by a higher voltage at any given time in Figure 5(a). From Figure 5(b), longer electron lifetimes are observed at higher TiO2 annealing temperatures. The slower decay and longer electron lifetimes are due to suppressed electron recombination at higher TiO2 annealing temperatures, as discussed above.

From Figure 5(b), the electron lifetime increased dramatically upon HfO2 deposition. For instance, when TiO2 was annealed at 500°C, HfO2 deposition increased the electron lifetime by more than an order of magnitude from 0.031 to 0.38 s at 0.4 V. The increased electron lifetime ultimately led to the increased efficiency as seen in Table 2.

4. Conclusions

In summary, ITO-TiO2 core-shell nanostructures are used as the photoanode of DSSCs. High-density, vertically aligned ITO nanowires are grown via a thermal evaporation method. Core-shell nanostructures are formed by coating the nanowires with TiO2 through TiCl4 treatment. TiO2 are annealed between 350 and 600°C and the photovoltaic properties of these devices are investigated. High annealing temperatures increase the crystallinity of the TiO2 shell and suppress electron recombination. High annealing temperatures also result in lower dye loading. The highest efficiency of 3.39% is achieved when TiO2 is annealed at 500°C. Inserting HfO2 blocking layers on nanowire surfaces further suppresses electron recombination from ITO to the electrolyte and a maximum efficiency of 5.83% is achieved. OCVD measurements indicate that HfO2 blocking layers increase the electron lifetime by more than an order of magnitude.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors acknowledge the support of the Donors of the American Chemical Society Petroleum Research Fund, the University of Florida Opportunity Fund, and the National Science Foundation (CBET-1033736) for support of this research.