Ozone Treatment Improved the Resistive Switching Uniformity of HfAlO<sub>2</sub> Based RRAM Devices

Liu, Lifeng; Hou, Yi; Zhang, Weibing; Han, Dedong; Wang, Yi

doi:https://doi.org/10.1155/2015/714097

Advances in Condensed Matter Physics

On this page

Abstract Introduction Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Special Issue

Si- and Ge-Based Electronic Devices

View this Special Issue

Research Article | Open Access

Volume 2015 | Article ID 714097 | https://doi.org/10.1155/2015/714097

Ozone Treatment Improved the Resistive Switching Uniformity of HfAlO₂ Based RRAM Devices

Lifeng Liu,¹Yi Hou,¹Weibing Zhang,¹Dedong Han,¹and Yi Wang¹

Academic Editor: Rui Zhang

Received22 Jan 2015

Accepted15 Feb 2015

Published23 Apr 2015

Abstract

HfAlO₂ based resistive random access memory (RRAM) devices were fabricated using atomic layer deposition by modulating deposition cycles for HfO₂ and Al₂O₃. Effect of ozone treatment on the resistive switching uniformity of HfAlO₂ based RRAM devices was investigated. Compared to the as-fabricated devices, the resistive switching uniformity of HfAlO₂ based RRAM devices with the ozone treatment is significantly improved. The uniformity improvement of HfAlO₂ based RRAM devices is related to changes in compositional and structural properties of the HfAlO₂ resistive switching film with the ozone treatment.

1. Introduction

Resistive switching phenomena in transitional metal oxide, such as HfO_x, TaO_x, are actively studied in order to apply them to the resistive random access memory (RRAM) [1–3]. RRAM is one of the most promising candidates for next generation of nonvolatile memory owing to its excellent performance, such as simple structure, low power consumption, fast switching speed, long retention time, and CMOS technology compatibility [4–6]. However, the key electrical characteristics of oxide-based RRAM devices still have random dispersion, such as operation voltage and high/low resistance values [7–12]. One of the main challenges that hinder RRAM devices from practical device application is exploring effective ways to suppress the fluctuations of key switching parameters, thus improving the resistive switching uniformity. Some technological methods have been presented to improve uniformity in oxide-based RRAM, such as using ion doping technical approach, specific top electrode materials, inserting interface layer between oxide and electrode, and applying certain operation model [9–12].

Ozone (O₃) treatment can change the compositional and structural properties of the oxide films which may have an effect on the resistance switching behavior of RRAM [13, 14]. In this paper, we investigated the electrical characteristics of HfAlO₂ based RRAM devices under different treatment processes and observed that the resistive switching uniformity of HfAlO₂ based RRAM devices can be significantly improved under the ozone treatment condition. The improvement of resistive switching uniformity is discussed.

2. Experiment

A 5 nm thick HfAlO₂ layer was fabricated on the Pt/Ti/SiO₂/Si substrate using atomic layer deposition by modulating deposition cycles for HfO₂ (derived from Hf[N(CH₃)(C₂H₅)]₄ and H₂O precursors) and Al₂O₃ (derived from Al(CH₃)₃ and H₂O precursors) at 250°C. The deposition cycle ratio of HfO₂ : Al₂O₃ was set 9 : 1. After the HfAlO₂ film deposition, some samples were treated in O₃ ambient at 100°C for 30 minutes; other samples without O₃ treatment were kept as control samples. Subsequently, a TaN top electrode with an area of 100 μm × 100 μm was fabricated by magnetron sputtering through a liftoff process. Cross-sectional RRAM stacks are schematically shown in Figure 1. The electrical characteristics of the fabricated RRAM devices were measured using a Keithley 4200 semiconductor parameter analyzer with biased voltage top and grounded bottom electrodes at room temperature. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structure and compositional characteristics of the HfAlO₂ film.

3. Results and Discussion

All the fresh HfAlO₂ based RRAM devices show high resistance state (HRS). An electric forming process with a high voltage was needed to realize reversible resistive switching, which is a precondition for activation of the soft breakdown of the HfAlO₂ film. After the electric forming process, stable reversible resistive switching between HRS and low resistance state (LRS) could be achieved in the HfAlO₂ based RRAM devices. Figure 2 shows the typical current-voltage () characteristics of as-deposited HfAlO₂ based RRAM devices without the ozone treatment. Typical bipolar resistive switching behaviors were observed in the RRAM devices. A current compliance (CC) during set process is necessary to protect the devices from damage. It can be seen from Figure 2 that the sharp set process from high resistance state (HRS) to low resistance state (LRS) takes place under positive voltage sweep and gradual reset process from LRS to HRS takes place under negative sweep.

The statistical distributions of key memory parameters of the HfAlO₂ based RRAM devices were measured by direct current (DC) voltage sweeping mode. Figures 3(a) and 3(b) compared the statistical distributions of HRS resistance () and LRS resistance () and set voltage () and reset voltage () from cycle to cycle separately between the HfAlO₂ based RRAM devices with and without the ozone treatment. Significantly reduced dispersions of both and and and are observed in the devices with ozone treatment. The resistance ratios of HRS to LRS in the HfAlO₂ based RRAM devices with the ozone treatment are more than 10 during the 512 cycles of DC resistive switching test, as shown in Figure 4.

(a)

(b)

Figure 5 shows the SEM images of the HfAlO₂ films with and without the ozone treatment. SEM measurement results revealed that surfaces of the as-deposited HfAlO₂ films were featureless and smooth. The nanoparticles’ size of as-deposited HfAlO₂ films is about 25 nm while it became larger to 30 nm after the ozone treatment. Figure 6 shows the X-ray photoelectron spectroscopy (XPS) of the O 1s and Hf 4f orbitals of argon sputtered HfAlO₂ films with spectrum aligned to C 1s on different treatment conditions. XPS depth analysis on the samples with and without the ozone treatment were also carried out. For the as-deposited HfAlO₂ film, the banding energy of Hf 4f_7/2 and Hf 4f_5/2 was around 16 and 18 eV, respectively, and O 1s was around 530 eV, consistent with the HfO₂ composition [4]. After the ozone treatment, the two distinct peaks corresponding to the Hf 4f_7/2 and 4f_5/2 of the Hf-O merged into one and the banding energy of O1s and Al 2s also increased, which could be attributed to the partial formation of new Hf-Al-O structure in the HfAlO₂ resistive switching film [13].

(a)

(b)

(a)

(b)

(c)

(d)

Various mechanisms have been proposed to explain the resistive switching behaviors in oxide-based RRAM devices, among which the formation/rupture of nanoscale conductive filaments (CFs) that consisted of oxygen vacancies (Vo) in the resistive switching layer has been widely recognized [15]. The origin of the switching performance variation may be due to the random formation of the CFs. Two possible reasons may be responsible for the improvement of resistive switching uniformity in the HfAlO₂ RRAM devices with the ozone treatment. First, ozone treatment can increase the film crystallinity, which could provide easy migration of oxygen vacancies along the grain boundaries [16], so oxygen vacancy conductive filaments can be formed in a more orderly way. Second, ozone treatment may change the compositional characteristic of the HfAlO₂ resistive switching layer and partially form the new Hf-Al-O structure, which is supported by the XPS results. Therefore, the improvement of resistive switching uniformity in HfAlO₂ based RRAM devices with the ozone treatment is related to the changes in compositional and structural properties of the HfAlO₂ resistive switching film after the ozone treatment.

4. Conclusions

HfAlO₂ based RRAM devices were fabricated using atomic layer deposition. The effects of ozone treatment on the resistive switching uniformity of HfAlO₂ based RRAM devices were investigated. Ozone treatment significantly improved the resistive switching uniformity of HfAlO₂ based RRAM devices. The SEM and XPS measurement results indicate that the uniformity improvement of HfAlO₂ based RRAM devices with the ozone treatment is related to the changes in compositional and structural properties of the HfAlO₂ resistive switching film with the ozone treatment.

Conflict of Interests

The authors declare no competing financial interest.

Acknowledgments

This work was supported in part by 973 and NSFC (nos. 2011CBA00600, 61376084, and 60925015).

References

Y. Z. Guo and J. Robertson, “Materials selection for oxide-based resistive random access memories,” Applied Physics Letters, vol. 105, no. 2, Article ID 223516, 2014.
View at: Publisher Site | Google Scholar
M. Zhang, S. Long, G. Wang et al., “Set statistics in conductive bridge random access memory device with Cu/HfO₂/Pt structure,” Applied Physics Letters, vol. 105, Article ID 193501, 2014.
View at: Publisher Site | Google Scholar
H.-S. P. Wong, H.-Y. Lee, S. M. Yu et al., “Metal-oxide RRAM,” Proceedings of the IEEE, vol. 100, no. 6, pp. 1951–1970, 2012.
View at: Publisher Site | Google Scholar
H. Akinaga and H. Shima, “Resistive random access memory (ReRAM) based on metal oxides,” Proceedings of the IEEE, vol. 98, no. 12, pp. 2237–2251, 2010.
View at: Publisher Site | Google Scholar
S. Yu, H.-Y. Chen, B. Gao, J. Kang, and H.-S. P. Wong, “HfOx-based vertical resistive switching random access memory suitable for bit-cost-effective three-dimensional cross-point architecture,” ACS Nano, vol. 7, no. 3, pp. 2320–2325, 2013.
View at: Publisher Site | Google Scholar
R. Waser and M. Aono, “Nanoionics-based resistive switching memories,” Nature Materials, vol. 6, no. 11, pp. 833–840, 2007.
View at: Publisher Site | Google Scholar
P.-T. Liu, Y.-S. Fan, and C.-C. Chen, “Improvement of resistive switching uniformity for Al-Zn-Sn-O-based memory device with inserting HfO₂ layer,” IEEE Electron Device Letters, vol. 35, no. 12, pp. 1233–1235, 2014.
View at: Publisher Site | Google Scholar
Y. S. Chen, B. Chen, B. Gao, L. F. Liu, X. Y. Liu, and J. F. Kang, “Well controlled multiple resistive switching states in the Al local doped HfO₂ resistive random access memory device,” Journal of Applied Physics, vol. 113, no. 16, Article ID 164507, 2013.
View at: Publisher Site | Google Scholar
H. W. Zhang, L. F. Liu, B. Gao et al., “Gd-doping effect on performance of HfO₂ based resistive switching memory devices using implantation approach,” Applied Physics Letters, vol. 98, no. 4, Article ID 042105, 2011.
View at: Publisher Site | Google Scholar
H. Jiang and Q. Xia, “Improvement of resistive switching uniformity for TiO₂-based memristive devices by introducing a thin HfO₂ layer,” Journal of Vacuum Science & Technology B: Microelectronics & Nanometer Structures, vol. 31, no. 6, Article ID 6FA04, 2013.
View at: Publisher Site | Google Scholar
C.-Y. Lin, C.-Y. Wu, C.-Y. C.-Y. Wu et al., “Effect of top electrode material on resistive switching properties of ZrO₂ film memory devices,” IEEE Electron Device Letters, vol. 28, no. 5, pp. 366–368, 2007.
View at: Publisher Site | Google Scholar
H. T. Liu, H. B. Lv, B. H. Yang et al., “Uniformity improvement in 1T1R RRAM with gate voltage ramp programming,” IEEE Electron Device Letters, vol. 35, no. 12, pp. 1224–1226, 2014.
View at: Publisher Site | Google Scholar
Z. R. Wang, W. G. Zhu, A. Y. Du et al., “Highly uniform, self-compliance, and forming-free ALD HfO₂-based RRAM with Ge doping,” IEEE Transactions on Electron Devices, vol. 59, no. 4, pp. 1203–1208, 2012.
View at: Publisher Site | Google Scholar
J. B. Sun, Z. W. Yang, Y. Geng et al., “Equivalent oxide thickness scaling of Al₂O3/Ge metal-oxide-semiconductor capacitors with ozone post oxidation,” Chinese Physics B, vol. 22, no. 6, Article ID 067701, 2013.
View at: Publisher Site | Google Scholar
B. Gao, B. Sun, H. W. Zhang et al., “Unified physical model of bipolar oxide-based resistive switching memory,” IEEE Electron Device Letters, vol. 30, no. 12, pp. 1326–1328, 2009.
View at: Publisher Site | Google Scholar
M. Y. Chan, T. Zhang, V. Ho, and P. S. Lee, “Resistive switching effects of HfO₂ high-k dielectric,” Microelectronic Engineering, vol. 85, no. 12, pp. 2420–2424, 2008.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2015 Lifeng Liu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1282

Downloads

1245

Citations

Advances in Condensed Matter Physics

Si- and Ge-Based Electronic Devices

Ozone Treatment Improved the Resistive Switching Uniformity of HfAlO2 Based RRAM Devices

Abstract

1. Introduction

2. Experiment

3. Results and Discussion

4. Conclusions

Conflict of Interests

Acknowledgments

References

Copyright

Ozone Treatment Improved the Resistive Switching Uniformity of HfAlO₂ Based RRAM Devices