A New Hybrid UPFC Controller for Power Flow Control and Voltage Regulation Based on RBF Neurosliding Mode Technique

Kenne, Godpromesse; Kuate, René Fochie; Fombu, Andrew Muluh; Nguimfack-Ndongmo, Jean de Dieu; Fotsin, Hilaire Bertrand

doi:https://doi.org/10.1155/2017/7873491

Advances in Electrical Engineering

On this page

Abstract Introduction Conclusion Appendix Conflicts of Interest References Copyright Related Articles

Research Article | Open Access

Volume 2017 | Article ID 7873491 | https://doi.org/10.1155/2017/7873491

A New Hybrid UPFC Controller for Power Flow Control and Voltage Regulation Based on RBF Neurosliding Mode Technique

Godpromesse Kenne,¹René Fochie Kuate,^1,2Andrew Muluh Fombu,^1,2Jean de Dieu Nguimfack-Ndongmo,¹and Hilaire Bertrand Fotsin²

Academic Editor: George E. Tsekouras

Received16 May 2017

Revised17 Jul 2017

Accepted17 Sept 2017

Published22 Oct 2017

Abstract

This paper presents a new technique to design a Unified Power Flow Controller (UPFC) for power flow control and DC voltage regulation of an electric power transmission system which is based on a hybrid technique which combines a Radial Basis Function (RBF) neural network (online training) with the sliding mode technique to take advantage of their common features. The proposed controller does not need the knowledge of the perturbation bounds nor the full state of the nonlinear system. Hence, it is robust and produces an optimal response in the presence of system parameter uncertainty and disturbances. The performance of the proposed controller is evaluated through numerical simulations on a Kundur power system and compared with a classical PI controller. Simulation results confirm the effectiveness, robustness, and superiority of the proposed controller.

1. Introduction

Presently, it is well established in the scientific community that the UPFC has the ability to increase the power flow capacity and improve the stability of an electric power transmission system through the proper design of its controller [1]. Over the past several decades, linear and nonlinear control techniques have been successfully proposed and applied in the literature for the control of UPFC based on modern and classical control theories [2–10]. However, the main drawback of such techniques is that their application requires the development of mathematical models which are difficult to obtain. Thus, only partial and quite weak results have been obtained in terms of online implementation feasibility.

Faced with these difficulties, intelligent controls such as fuzzy logic and artificial neural networks have emerged as better alternatives to the conventional linear and nonlinear control methods. However, the complexities associated with the adaption of membership functions and computation requirements for defuzzification have hindered the application of fuzzy logic [11–15]. Hence, recent studies have turned to artificial neural networks (ANN) to achieve the desired goals [16–18].

Artificial neural networks have an inherent capability to learn and store information regarding the nonlinearities of the system and to provide this information whenever required. This renders the neural networks suitable for system identification and control applications [19–21]. Although intelligent and hybrid algorithms are already being implemented in the domains of image processing, robotics, financial management, and so on, their application in the field of FACTS devices for power flow control is fairly recent. Some recent results can be found in [12, 16, 17, 22, 23].

In [16], a radial basis function neural network has been designed to control the operation of the UPFC in order to improve its dynamic performance. Simulation and experimental results were presented to demonstrate the robustness of the proposed controller against changes in the transmission system operating conditions. However, large memory and long computation time are required for its proper functioning and, in addition, the controller is designed under the assumption that the upper bound of the disturbance is known. A comparative study of transient stability and reactive power compensation issues in an autonomous wind-diesel-photovoltaic based hybrid system using robust fuzzy-sliding mode based Unified Power Flow Controller has been presented in [12], but it has the limitation that a linearized small-signal model of the hybrid system is considered for the transient stability analysis. Hence, the system will suffer from performance degeneracy when the operating condition changes. In [22], the recently proposed -learning method for updating the parameter of a single neuron radial basis function neural network has been used as a control scheme for the UPFC to improve the transient stability performance of a multimachine power system. However, the updating control parameters are optimized for each perturbation using a generic algorithm which increases the computational burden and makes the control implementation less feasible. A neural network predictive controller for the UPFC has been designed in [23] to improve the transient stability performance of the power system. Nevertheless, the neural network controller is implemented only on the series branch of the UPFC which limits the performance of the device. In [17], a neural network controller based on a feedback linearization autoregression average model is used to design an adaptive-supplementary unified power flow control for two interconnected areas of a power system. However, in this paper and many others, the bounds of system uncertainty and disturbances are assumed to be known. But in practice, it is always difficult to determine the exact upper limit of system uncertainty and disturbances. Hence, the above controllers cannot provide satisfactory results.

From the above drawbacks, in this paper, a new hybrid approach which combines RBF neural network with the sliding mode technique to design a UPFC controller for power flow control and DC voltage regulation of an electric power transmission system with unknown bounds of system uncertainty and disturbances is proposed. The advantages of this design philosophy are that the controller is suitable for practical implementation and it makes the design useful for the real world complex power system. The remaining sections of this paper are organized as follows. In Section 2, the mathematical model of a UPFC in reference frame is described. The design of the RBF neurosliding mode controller is developed in Section 3. In Section 4, simulation results in a Kundur two-area four-machine power system are presented. Finally, in Section 5, some concluding remarks end the paper.

2. System Modeling

Figure 1(a) shows a schematic diagram of a UPFC system, while Figure 1(b) shows a single-phase representation of the power circuit of the UPFC which consists of two back-to-back self-commutated voltage source converters connected through a common DC-link [24, 25]. The series converter is coupled to the AC system through a series transformer and the shunt converter is coupled through a shunt transformer. In Figure 1(b), the series and shunt converters are represented by the voltage sources and , respectively. The subscripts “,” “,” and “” are used to represent the sending-end bus, receiving end bus, and the three-phase quantities (phases ), respectively. Also and represent the resistance and leakage inductance of series converter, respectively, is the line current, , , and are the resistance, inductance, and current of the shunt converter, respectively. The series and shunt branch currents of the circuit in Figure 1(b) can be expressed by the following three-phase system of differential equations [24–26]:

(a)

(b)

Using Park’s transformation and assuming that the instantaneous power is kept invariant and the sending-end voltage vector is in the -axis (i.e., ), the three-phase system of differential equations (1) can be transformed into an equivalent two-phase system of equations as follows: where is the fundamental angular frequency of the supply voltage and is the angular frequency of synchronous reference frame .

Since the series and shunt converters of the UPFC are coupled through a common DC-link, if the losses in the converters are neglected, then the dynamic of the DC-link voltage can be expressed as [27]where and are the active power supplied by the series and shunt converters, respectively, and is the voltage of the DC capacitor of capacitance .

It is clear from (6) that decreases when and it increases when . Note that (6) is a nonlinear differential equation and has to be investigated at an operating point. However, the derivative of can be written asUsing (6) and (7), the derivative of can be expressed asMaintaining constant DC-link voltage is very important for the UPFC control system [1, 28, 29]. The DC-link voltage varies when . Since (8) does not contain a direct control signal like (4), we will consider as an auxiliary input that can be used to maintain the DC-link voltage constant.

3. UPFC RBF Neurosliding Mode Controller Design

In this section, the method proposed in [30, 31] for time-varying parameter estimation will be modified and applied to design a robust adaptive controller for the UPFC using the RBF neural network.

Let us consider the SISO first-order nonlinear system in the following form: where , , and are state variables, system input, and system output, respectively; and are unknown smooth functions; represents the nominal part of the system which does not depend upon the control input, while the uncertainties and external disturbance are concentrated in the term assumed to be bounded by an unknown constant . Since all physical plants operate in bounded regions, we study the control problem of system (9) whose state belongs to a compact subset .

Let the desired smooth signal , the tracking error , and augmented item be defined aswhere is a design parameter. The integral term is included in the sliding manifold so as to ensure that the system trajectories start on the sliding manifold from the first instant of time. From (10), we haveFrom , if the desired sliding mode controller is chosen as [31]where is a design parameter, then and will converge exponentially to .

The above desired controller (12) is not implementable in practice since the functions and and the terms and are assumed to be unknown. Hence, in this work, a RBF neural network combined with the sliding mode technique will be applied to approximate the unknown controller .

The control signal (12) can be approximated by the neural controller proposed in [31] aswhere denotes a nonlinear function; and , , are the center and the width of the th hidden unit, respectively; is the number of hidden nodes or Radial Basis Function (RBF) units; is the optimal weight vector and satisfies ; is the input vector of the RBF network; is the optimal approximation error, which is unknown and bounded .

and , , are chosen, respectively, using the Clustering algorithm [32] as follows:where and are the lower and upper bounds of the th element of the RBF input vector , respectively.

Note that the term is time-varying and cannot be approximated by a static neural network. In the following analysis, sliding robust terms will be used in the identification scheme to compensate the effect of this uncertainty time-varying term. The controller will be approximated assuming that the terms and are bounded by unknown positive constants.

For this purpose, the following neural controller is proposed in order to approximate the control signal where the term is introduced in order to improve the convergence rate of the neural network in the presence of the uncertainties terms.

Consider the systems described by (9), the sliding-neural network controller (15), and Assumptions 1 and 2 given in [31]. If the bias term , the learning rule of the weight , and the adaptation law for the unknown bound are chosen as with , , and the well-known projection function [33] on the compact set , then the neural network controller error will converge in finite time to the origin. The proof of the convergence of above neural network controller to zero can be found in [31].

In order to apply the neurosliding controller described above to power flow control, UPFC sending-end bus voltage control and DC-link voltage control, the dynamic equations of the UPFC completely described by (2) to (5) and (8) can be rewritten as with where to represent system uncertainties.

The reference values of the state variables are obtained aswhere and are the active and reactive power references at the receiving end bus of the transmission line, respectively.

We can design the neurosliding controller using the UPFC dynamics given in (17) as (for )

4. Simulation Results

The performance of the proposed nonlinear controller is evaluated through digital simulations using MATLAB/SIMULINK software. The power system used is a Kundur two-area four-machine power system shown in Figure 2. The details of system data and initial operating point are given in [34]. The proposed controller can be applied to a UPFC connected between any two buses of the power system (with bus) regardless of the interaction between these two buses and other buses. Only local measurements information is required for the implementation of the proposed algorithm. The simulation results of the proposed controller (SNC) are compared with conventional Proportional Integral (PI) controllers used for power flow control, UPFC sending-end bus voltage control, and DC-link voltage control. These classical controllers are tuned using optimal control techniques and the parameters obtained are given in the Appendix. To evaluate the performance of the proposed controller, four sets of simulations have been performed. In all simulations, the uncertainty factor is set at . That is the parameters of the system under simulation are set at compared to the same parameters introduced in the controller.

4.1. Step Changes in Transmission Line Real and Reactive Power Flow References

In this case study, the initial complex power flow at the receiving end of the transmission line is found as pu. A step change in active power reference from 1.8 to 2.2 pu and reactive power reference from 0.0 to 0.5 pu of the transmission line take place at s and 0.32 s, respectively. The simulation results for this case study are depicted in Figures 3 and 4. It can be seen from these figures that the active and reactive power flow through the transmission line, the UPFC DC-link voltage, and the voltage magnitude at bus B2 are controlled effectively. The results also clearly show that the response speed and transient conditions are further improved with the proposed controller as compared to the conventional PI controllers. Figure 4 clearly shows the excellent performance of the UPFC in power flow control under the influence of the proposed controller.

(a)

(b)

(a)

(b)

4.2. Load Variation

In practice, the references values of the control power system remain constant and the quantities being controlled vary under the effect of load variation, disturbance, and other perturbations. In this case study, the load increases by of its nominal value from s. The simulation results are depicted in Figure 5. It can be noticed in these figures that the active and reactive power flow through the transmission line, the DC-link voltage, and the voltage magnitude at bus B2 are all regulated to their respective reference values. Figure 5 shows that the excess active and reactive power requested by the load is supplied only by generator G2. The figure also demonstrates once more the excellent performance of the proposed controller in terms of overshot and settling time.

(a)

(b)

4.3. Robustness to Measurement Noise

In practice, it is not possible to measure a signal accurately due to the presence of noise. For this reason, the third case study investigates the robustness of the proposed nonlinear controller with respect to measurement noise (uncertainties). In this case study, all simulations are conducted under noise conditions in the measured line currents with the magnitude of the noise reaching about of the maximum value of the measurable line currents. A step change in reactive power under the same conditions as in the first case study is used to evaluate the robustness of the system. The simulation results for this case study are depicted in Figure 6. From these results, it can be seen that the active and reactive power flow through the transmission line, the UPFC DC-link voltage, and the voltage magnitude at bus B2 are all regulated to their respective reference values despite the presence of measurement noise. Hence, it can be concluded that the controller exhibits an excellent noise resistance.

(a)

(b)

4.4. Three-Phase-to-Ground Fault Test

In this case study, a three-phase-to-ground fault is applied on bus-5 and the fault is cleared after 100 ms. Simulation results for this case study are shown in Figure 7. From these results, it can be seen that the proposed controller rapidly steers the system to its prefault steady state and satisfactorily improves the transient stability of the power system as compared to the conventional PI controllers.

(a)

(b)

5. Conclusion

In this paper, a new hybrid approach which combines Radial Basis Function (RBF) neural network with the sliding mode technique has been used to design a Unified Power Flow Controller (UPFC) for power flow control, UPFC sending-end voltage control, and DC voltage regulation of an electric power transmission system. The RBF neurosliding mode control technique uses online training to get its optimal parameter values. The proposed technique is robust and does not need the knowledge of the perturbation bounds nor the full state of the nonlinear system. The performance of the proposed controller has been evaluated through simulations on a Kundur power system and compared with a classical PI controller. Simulation results have shown the effectiveness and satisfactory performance of the proposed controller in dealing with the perturbations considered. Future works should be targeted towards the extension of the proposed hybrid approach to a wide area interconnected power system for power oscillation damping.

Appendix

Simulation Parameters

(i)The parameters of the UPFC are shown in Table 1.(ii)PI controllers parameters are as follows: Series converter: ; . Shunt converter: ; . DC-link: ; .(iii)RBF controller parameters are as follows: The values of are randomly initialized.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

References

I. Papic, P. Zunko, D. Povh, and M. Weinhold, “Basic control of unified power flow controller,” IEEE Transactions on Power Systems, vol. 12, no. 4, pp. 1734–1739, 1997.
View at: Publisher Site | Google Scholar
S. Kannan, S. Jayaram, and M. M. A. Salama, “Real and reactive power coordination for a unified power flow controller,” IEEE Transactions on Power Systems, vol. 19, no. 3, pp. 1454–1461, 2004.
View at: Publisher Site | Google Scholar
B. Lu and B.-T. Ooi, “Nonlinear control of voltage-source converter systems,” IEEE Transactions on Power Electronics, vol. 22, no. 4, pp. 1186–1195, 2007.
View at: Publisher Site | Google Scholar
A. Zangeneh, A. Kazemi, M. Hajatipour, and S. Jadid, “A Lyapunov theory based UPFC controller for power flow control,” International Journal of Electrical Power & Energy Systems, vol. 31, no. 7-8, pp. 302–308, 2009.
View at: Publisher Site | Google Scholar
B. Lei and S. Fei, “A brand new nonlinear robust control design of SSSC for transient stability and damping improvement of multi-machine power systems via pseudo-generalized Hamiltonian theory,” Control Engineering Practice, vol. 29, pp. 147–157, 2014.
View at: Publisher Site | Google Scholar
J. D. D. Nguimfack-Ndongmo, G. Kenné, R. Kuate-Fochie, A. Cheukem, H. B. Fotsin, and F. Lamnabhi-Lagarrigue, “A simplified nonlinear controller for transient stability enhancement of multimachine power systems using SSSC device,” International Journal of Electrical Power & Energy Systems, vol. 54, pp. 650–657, 2014.
View at: Publisher Site | Google Scholar
A. Ajami, S. H. Hosseini, S. Khanmohammadi, and G. B. Gharehpetian, “Modeling and control of C-UPFC for power system transient studies,” Simulation Modelling Practice and Theory, vol. 14, no. 5, pp. 564–576, 2006.
View at: Publisher Site | Google Scholar
A. Hamache, M. O. Bensidhoum, and H. Chekireb, “RoRobust sliding mode control of unified power flow controllerfor power flow tracking,” in Proceedings of the 8th International Conference on Modelling, Identification and Control (ICMIC '16), pp. 412–417, Algiers, Algeria, November 2016.
View at: Publisher Site | Google Scholar
A. Khodabakhshian, M. R. Esmaili, and M. Bornapour, “Optimal coordinated design of UPFC and PSS for improving power system performance by using multi-objective water cycle algorithm,” International Journal of Electrical Power & Energy Systems, vol. 83, pp. 124–133, 2016.
View at: Publisher Site | Google Scholar
S. K. Routray, R. K. Patnaik, and P. K. Dash, “Adaptive non-linear control of UPFC for stability enhancement in a multimachine power system operating with a DFIG based wind farm,” Asian Journal of Control, vol. 19, no. 5, pp. 1–20, 2017.
View at: Publisher Site | Google Scholar
L. Saribulut, A. Teke, and M. Tümay, “Dynamic control of unified power flow controller under unbalanced network conditions,” Simulation Modelling Practice and Theory, vol. 19, no. 2, pp. 817–836, 2011.
View at: Publisher Site | Google Scholar
A. Mohanty, S. Patra, and P. K. Ray, “Robust fuzzy-sliding mode based UPFC controller for transient stability analysis in autonomous wind-diesel-PV hybrid system,” IET Generation, Transmission & Distribution, vol. 10, no. 5, pp. 1248–1257, 2016.
View at: Publisher Site | Google Scholar
M. Fadi, A. Shameem, M. Saad, A. Ibrahim, and A. H. Mohd Fairuz, “Power flow control using fuzzy based UPFC under different operating conditions,” Journal of Electrical Systems, vol. 13, no. 2, pp. 398–414, 2017.
View at: Google Scholar
F. M. Albatsh, S. Mekhilef, S. Ahmad, and H. Mokhlis, “Fuzzy logic based UPFC and laboratory prototype validation for dynamic power flow control in transmission lines,” IEEE Transactions on Industrial Electronics, 2017.
View at: Publisher Site | Google Scholar
M. Khaksar, A. Rezvani, and M. H. Moradi, “Simulation of novel hybrid method to improve dynamic responses with PSS and UPFC by fuzzy logic controller,” Neural Computing and Applications, 2016.
View at: Publisher Site | Google Scholar
M. E. A. Farrag and G. Putrus, “An on-line training radial basis function neural network for optimum operation of the UPFC,” European Transactions on Electrical Power, vol. 21, no. 1, pp. 27–39, 2011.
View at: Publisher Site | Google Scholar
N. Zeb, B. Khan, S. M. Ali et al., “Adaptive controller based unified power flow control for low power oscillation damping,” Asian Journal of Control, vol. 20, no. 1, pp. 1–10, 2017.
View at: Publisher Site | Google Scholar
M. J. Rana, M. S. Shahriar, and M. Shafiullah, “Levenberg–Marquardt neural network to estimate UPFC-coordinated PSS parameters to enhance power system stability,” Neural Computing and Applications, 2017.
View at: Publisher Site | Google Scholar
Q. Zhu, S. Fei, T. Zhang, and T. Li, “Adaptive RBF neural-networks control for a class of time-delay nonlinear systems,” Neurocomputing, vol. 71, no. 16–18, pp. 3617–3624, 2008.
View at: Publisher Site | Google Scholar
J. Liu, Radial Basis Function (RBF) Neural Network Control for Mechanical Systems, Design, Analysis and Matlab Simulation, Springer, Heidelberg, Germany, 2013.
C. C. Hua, C. X. Yu, and X. P. Guan, “Neural network observer-based networked control for a class of nonlinear systems,” Neurocomputing, vol. 133, pp. 103–110, 2014.
View at: Publisher Site | Google Scholar
S. Mishra, “Neural-network-based adaptive UPFC for improving transient stability performance of power system,” IEEE Transactions on Neural Networks and Learning Systems, vol. 17, no. 2, pp. 461–470, 2006.
View at: Publisher Site | Google Scholar
S. Tiwari, R. Naresh, and R. Jha, “Neural network predictive control of UPFC for improving transient stability performance of power system,” Applied Soft Computing, vol. 11, no. 8, pp. 4581–4590, 2011.
View at: Publisher Site | Google Scholar
C. M. Yam and M. H. Haque, “A SVD based controller of UPFC for power flow control,” Electric Power Systems Research, vol. 70, no. 1, pp. 76–84, 2004.
View at: Publisher Site | Google Scholar
M. A. Sayed and T. Takeshita, “All nodes voltage regulation and line loss minimization in loop distribution systems using UPFC,” IEEE Transactions on Power Electronics, vol. 26, no. 6, pp. 1694–1703, 2011.
View at: Publisher Site | Google Scholar
M. E. Elgamal, A. Lotfy, and G. E. M. Ali, “Voltage profile enhancement by fuzzy controlled MLI UPFC,” International Journal of Electrical Power & Energy Systems, vol. 34, no. 1, pp. 10–18, 2012.
View at: Publisher Site | Google Scholar
H. Chen, Y. Wang, and R. Zhou, “Transient stability enhancement via coordinated excitation and UPFC control,” International Journal of Electrical Power & Energy Systems, vol. 24, no. 1, pp. 19–29, 2002.
View at: Publisher Site | Google Scholar
H. Fujita, Y. Watanabe, and H. Akagi, “Transient analysis of a unified power flow controller and its application to design of the dc-link capacitor,” IEEE Transactions on Power Electronics, vol. 16, no. 5, pp. 735–740, 2001.
View at: Publisher Site | Google Scholar
I. Axente, M. Basu, and M. F. Conlon, “Dc link voltage control of UPQC for better dynamic performance,” Electric Power Systems Research, vol. 81, no. 9, pp. 1815–1824, 2011.
View at: Publisher Site | Google Scholar
T. Ahmed-Ali, G. Kenné, and F. Lamnabhi-Lagarrigue, “Identification of nonlinear systems with time-varying parameters using a sliding-neural network observer,” Neurocomputing, vol. 72, no. 7-9, pp. 1611–1620, 2009.
View at: Publisher Site | Google Scholar
G. Kenné, A. S. Fotso, and F. Lamnabhi-Lagarrigue, “A new adaptive control strategy for a class of nonlinear system using RBF neuro-sliding-mode technique: application to SEIG wind turbine control system,” International Journal of Control, vol. 90, no. 4, pp. 855–872, 2017.
View at: Publisher Site | Google Scholar
A. K. Jain and R. C. Dubes, Algorithms for Clustering Data, Prentice Hall, 1988.
View at: MathSciNet
D. Luenberger, Linear and Nonlinear Programming, Addison-Wesley Publishing Company, Reading, Mass, USA, 1984.
P. Kundur, Power System Stability and Control, McGraw-Hill, New York, NY, USA, 1994.

Copyright

Copyright © 2017 Godpromesse Kenne et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2418

Downloads

409

Citations