Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2013 (2013), Article ID 367543, 8 pages
http://dx.doi.org/10.1155/2013/367543
Research Article

Effects of Nitride on the Tribological Properties of the Low Carbon Alloy Steel

1Department of Mechanical Engineering, Kun Shan University, Tainan 710, Taiwan
2Department of Power Mechanical Engineering, National Formosa University, Yunlin 632, Taiwan
3Department of Mechanical and Automation Engineering, I-Shou University, Kaohsiung 840, Taiwan
4Hiwin Technologies Corp., Taichung 40707, Taiwan

Received 15 September 2013; Accepted 2 November 2013

Academic Editor: Shoou-Jinn Chang

Copyright © 2013 Yuh-Ping Chang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. W. D. Callister, Material Science, Engineering: An Introduction, Wiley, New York, NY, USA, 3rd edition, 1994.
  2. K. E. Thelning, Steel and Its Heat Treatment, Bofors Handbook, 1975.
  3. D. H. Huang and G. Thomas, “Structure and mechanical properties of tempered martensite and lower bainite in Fe–Ni–Mn–C steels,” Metallurgical Transactions, vol. 2, no. 6, pp. 1587–1598, 1971. View at Publisher · View at Google Scholar · View at Scopus
  4. A. M. Nasreldin, M. M. Ghoneim, F. H. Hammad, R. L. Klueh, and R. K. Nanstad, “Effect of tempering on the toughness of a Cr–Mo bainitic steel,” Journal of Materials Engineering and Performance, vol. 2, no. 3, pp. 413–420, 1993. View at Publisher · View at Google Scholar
  5. J. Guodong and H. Maolin, “Research on overheat hardening technology for 5CrMnMo steel,” Material & Heat Treatment, pp. 74–75, 2008. View at Google Scholar
  6. P. Clayton and R. Devanathan, “Rolling/sliding wear behavior of a chromium-molybdenum rail steel in pearlitic and bainitic conditions,” Wear, vol. 156, no. 1, pp. 121–131, 1992. View at Google Scholar · View at Scopus
  7. Z. Canxu, Z. Li, D. Yi, and M. Liqun, Effect of Middle-Temperature Heat-Treatment on Microstructure and Tensile Strength of Ferritic Stainless Steel, Nanjing University of Technology, Nanjing, China, 2009.
  8. M. F. Carlson, B. V. Narasimha Rao, and G. Thomas, “The effect of austenitizing temperature upon the microstructure and mechanical properties of experimental Fe/Cr/C steels,” Metallurgical Transactions A, vol. 10, no. 9, pp. 1273–1284, 1979. View at Publisher · View at Google Scholar · View at Scopus
  9. H. Chai and C. Laird, “Mechanisms of cyclic softening and cyclic creep in low carbon steel,” Materials Science and Engineering, vol. 93, no. C, pp. 159–174, 1987. View at Google Scholar · View at Scopus
  10. Y. P. Chang, J. P. Yur, H. M. Chou, and H. M. Chu, “Tribo-electrification mechanisms for self-mated carbon steels in dry severe wear process,” Wear, vol. 260, no. 11-12, pp. 1209–1216, 2006. View at Publisher · View at Google Scholar · View at Scopus
  11. Y. P. Chang, H. M. Chu, and H. M. Chou, “Effects of mechanical properties on the tribo-electrification mechanisms of iron rubbing with carbon steels,” Wear, vol. 262, no. 1-2, pp. 112–120, 2007. View at Publisher · View at Google Scholar · View at Scopus
  12. Y. P. Chang, Y. Y. Hung, L. M. Chu, J. P. Yur, and C. H. Lin, “The surface magnetization approach on assessing tribological properties of steels with different TiN coatings,” Proceedings of the Institution of Mechanical Engineers J, vol. 223, no. 4, pp. 715–722, 2009. View at Publisher · View at Google Scholar · View at Scopus
  13. Y. P. Chang, J. H. Horng, J. P. Yur, L.-M. Chu, and Y.-C. Hwang, “The surface magnetization approach on assessing the tribological properties of iron sliding against iron coated with pure tin and with a tin composite,” Proceedings of the Institution of Mechanical Engineers J, vol. 225, no. 12, pp. 1199–1208, 2011. View at Publisher · View at Google Scholar · View at Scopus