Table of Contents Author Guidelines Submit a Manuscript
Retracted

Advances in Materials Science and Engineering has retracted this article. The corresponding author apologizes and the authors agree with retraction. The article was found to contain a substantial amount of material, without citation, from the following published articles:

Figures and Text

(i) Wording in the section “3.1. Microstructure Analysis” and Figure 5 were from Hiroyuki Fukuda, Katsuyoshi Kondoh, Junko Umeda, Bunshi Fugetsu: Interfacial analysis between Mg matrix and carbon nanotubes in Mg–6 wt.% Al alloy matrix composites reinforced with carbon nanotubes. Composites Science and Technology 2011, Vol. 71(5): 705–709. DOI: 10.1016/j.compscitech.2011.01.015

(ii) Wording in the section “3.1. Microstructure Analysis” and Figure 4 were from M.S. Senthil Saravanan, S.P. Kumaresh Babu, K. Sivaprasad: Mechanically Alloyed Carbon Nanotubes (CNT) Reinforced Nanocrystalline AA 4032: Synthesis and Characterization. Journal of Minerals & Materials Characterization & Engineering, Vol. 9, No. 11, pp. 1027–1035, 2010

Text

(iii) C S Goh, J Wei, L C Lee and M Gupta: Development of novel carbon nanotube reinforced magnesium nanocomposites using the powder metallurgy technique. Nanotechnology, Volume 17, Number 1. Published 25 November 2005 (cited in the background, but not in the section “3.2. Mechanical Properties”)

(iv) Ahmed Sayed Salim Mohamed: Fabrication and Properties of Carbon Nanotube (CNT) – Reinforced Aluminium Composites. The American University in Cairo School of Sciences & Engineering, Spring 2010

Figure

(v) Figure 8(a) was simultaneously published as Figure 1 in J. Jayakumar, B. K. Raghunath, T. H. Rao: Investigation on Fracture Mechanisms in Mg alloy AZ31 Nano Composites Reinforced with Multi Wall Carbon Nano Tubes. International Journal of Innovative Research in Science, Engineering and Technology, Vol. 2, Issue 9, September 2013

View the original article here.

References

  1. J. Jayakumar, B. K. Raghunath, and T. H. Rao, “Enhancing microstructure and mechanical properties of AZ31-MWCNT nanocomposites through mechanical alloying,” Advances in Materials Science and Engineering, vol. 2013, Article ID 539027, 6 pages, 2013.
Advances in Materials Science and Engineering
Volume 2013 (2013), Article ID 539027, 6 pages
http://dx.doi.org/10.1155/2013/539027
Research Article

Enhancing Microstructure and Mechanical Properties of AZ31-MWCNT Nanocomposites through Mechanical Alloying

1Department of Manufacturing Engineering, Annamalai University, Chidambaram, Tami Nadu, India
2Department of Mechanical Engineering, PDVVP College of Engineering, Ahmednagar, Maharashtra, India

Received 27 May 2013; Revised 14 September 2013; Accepted 15 September 2013

Academic Editor: Bin Zhang

Copyright © 2013 J. Jayakumar et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Y. Zheng, K. Wu, and C. K. Yao, “Effect of interfacial reaction on mechanical behavior of SiCw/AZ91 magnesium matrix composites,” Materials Science and Engineering A, vol. 318, no. 1-2, pp. 50–56, 2001. View at Publisher · View at Google Scholar · View at Scopus
  2. C. S. Goh, J. Wei, L. C. Lee, and M. Gupta, “Development of novel carbon nanotubes reinforced magnesium nanocomposites using powder metallurgy technique,” SIMTech Technical Reports, vol. 9, no. 3, 2008. View at Google Scholar
  3. S. Seshan, M. Jayamathy, S. V. Kailas, and T. S. Srivatsan, “The tensile behavior of two magnesium alloys reinforced with silicon carbide particulates,” Materials Science and Engineering A, vol. 363, no. 1-2, pp. 345–351, 2003. View at Publisher · View at Google Scholar · View at Scopus
  4. M. Gupta, M. O. Lai, and D. Saravanaranganathan, “Synthesis, microstructure and properties characterization of disintegrated melt deposited Mg/SiC composites,” Journal of Materials Science, vol. 35, no. 9, pp. 2155–2165, 2000. View at Publisher · View at Google Scholar · View at Scopus
  5. M. Manoharan, S. C. V. Lim, and M. Gupta, “Application of a model for the work hardening behavior to Mg/SiC composites synthesized using a fluxless casting process,” Materials Science and Engineering A, vol. 333, no. 1-2, pp. 243–249, 2002. View at Publisher · View at Google Scholar · View at Scopus
  6. S. Iijima, “Helical microtubules of graphitic carbon,” Nature, vol. 354, no. 6348, pp. 56–58, 1991. View at Google Scholar · View at Scopus
  7. M. R. Falvo, G. J. Clary, R. M. Taylor et al., “Bending and buckling of carbon nanotubes under large strain,” Nature, vol. 389, no. 6651, pp. 582–584, 1997. View at Publisher · View at Google Scholar · View at Scopus
  8. S. Dong and X. Zhang, “Mechanical properties of Cu-based composites reinforced by carbon nanotubes,” Transactions of Nonferrous Metals Society of China, vol. 19, pp. 457–461, 1999. View at Google Scholar
  9. S. R. Dong, J. P. Tu, and X. B. Zhang, “An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes,” Materials Science and Engineering A, vol. 313, no. 1-2, pp. 83–87, 2001. View at Publisher · View at Google Scholar · View at Scopus
  10. X. Chen, J. Xia, J. Peng, W. Li, and S. Xie, “Carbon-nanotube metal-matrix composites prepared by electroless plating,” Composites Science and Technology, vol. 60, no. 2, pp. 301–306, 2000. View at Google Scholar · View at Scopus
  11. T. Kuzumaki, O. Ujiie, H. Ichinose, and K. Ito, “Mechanical characteristics and preparation of carbon nanotube fiber-reinforced Ti composite,” Advanced Engineering Materials, vol. 2, no. 7, pp. 416–418, 2000. View at Google Scholar · View at Scopus
  12. P. R. Soni, Mechanical Alloying: Fundamentals and Applications, Cambridge International Science Publishing, 1998.
  13. Z. L. Pei, K. Li, J. Gong, N. L. Shi, E. Elangovan, and C. Sun, “Micro-structural and tensile strength analyses on the magnesium matrix composites reinforced with coated carbon fiber,” Journal of Materials Science, vol. 44, no. 15, pp. 4124–4131, 2009. View at Publisher · View at Google Scholar · View at Scopus
  14. R. J. Arsenault and N. Shi, “Dislocation generation due to differences between the coefficients of thermal expansion,” Materials Science and Engineering, vol. 81, pp. 175–187, 1986. View at Google Scholar · View at Scopus
  15. P. S. Grant, “Spray forming,” Progress in Materials Science, vol. 39, no. 4-5, pp. 497–545, 1995. View at Publisher · View at Google Scholar
  16. P. M. Kelly, “The effect of particle shape on dispersion hardening,” Scripta Metallurgica, vol. 6, no. 8, pp. 647–656, 1972. View at Google Scholar · View at Scopus
  17. S. R. Agnew and O. Duygulu, “Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B,” International Journal of Plasticity, vol. 21, no. 6, pp. 1161–1193, 2005. View at Publisher · View at Google Scholar · View at Scopus
  18. G. E. Dieter, Mechanical Metallurgy, McGraw-Hill, London, UK, 1988.
  19. S. F. Hassan and M. Gupta, “Development of ductile magnesium composite materials using titanium as reinforcement,” Journal of Alloys and Compounds, vol. 345, no. 1-2, pp. 246–251, 2002. View at Publisher · View at Google Scholar · View at Scopus
  20. S. F. Hassan and M. Gupta, “Development of high performance magnesium nano-composites using nano-Al2O3 as reinforcement,” Materials Science and Engineering A, vol. 392, no. 1-2, pp. 163–168, 2005. View at Publisher · View at Google Scholar · View at Scopus