Parametric Optimization of Squeeze Cast AC2A-Ni Coated <svg     style="vertical-align:-7.34404pt;width:40.375px;" id="M1" height="24.174999" version="1.1" viewBox="0 0 40.375 24.174999" width="40.375"  xmlns:xlink="http://www.w3.org/1999/xlink" xmlns="http://www.w3.org/2000/svg">
	
		
			<g transform="matrix(.022,-0,0,-.022,.062,14.975)"><path id="x53" d="M409 504l-29 -5q-16 60 -44.5 96t-86.5 36q-54 0 -82.5 -32t-28.5 -77q0 -51 30.5 -82.5t96.5 -65.5l35.5 -18t33 -19.5t33.5 -23.5l27 -25.5t24.5 -32t13.5 -36.5t6 -45q0 -80 -62 -134.5t-160 -54.5q-47 0 -98 15q-22 7 -50 21q-8 23 -27 155l30 7q7 -27 18 -52
t30 -51.5t49 -42.5t67 -16q56 0 88 32.5t32 87.5q0 51 -31.5 82t-98.5 67q-80 44 -110 73q-55 53 -55 124q0 75 56 126.5t150 51.5q53 0 126 -23z" /></g><g transform="matrix(.022,-0,0,-.022,10.553,14.975)"><path id="x69" d="M135 536q-20 0 -35 15.5t-15 35.5q0 22 15 37t36 15t35.5 -15t14.5 -37q0 -21 -15 -36t-36 -15zM252 0h-220v26q48 5 59 17t11 63v206q0 47 -9 58t-54 18v24q78 12 142 39v-345q0 -51 11.5 -63t59.5 -17v-26z" /></g><g transform="matrix(.022,-0,0,-.022,16.561,14.975)"><path id="x43" d="M614 175l29 -10q-33 -109 -57 -154q-121 -26 -184 -26q-90 0 -160.5 29t-112.5 77t-63.5 105.5t-21.5 119.5q0 157 108 253t277 96q36 0 71.5 -5t69 -13.5t36.5 -8.5q15 -102 20 -150l-29 -8q-20 79 -66.5 114t-128.5 35q-119 0 -187.5 -86t-68.5 -207
q0 -140 73.5 -227.5t188.5 -87.5q73 0 119.5 37.5t86.5 116.5z" /></g>

			<g transform="matrix(.016,-0,0,-.016,31.463,20.35)"><path id="x70" d="M169 380l92 53q26 16 49 16q80 0 128.5 -56t48.5 -133q0 -108 -72.5 -180.5t-176.5 -91.5q-38 1 -69 18v-131q0 -57 13 -70t71 -18v-27h-236v27q49 5 61 17t12 61v452q0 48 -9.5 58.5t-56.5 16.5v24q66 11 145 43v-79zM169 346v-270q37 -39 94 -39q63 0 101.5 50
t38.5 134q0 78 -38.5 123t-95.5 45q-45 0 -100 -43z" /></g>

		
	
</svg> Composite Using Taguchi Technique

Ravikumar, A. R.; Amirthagadeswaran, K. S.; Senthil, P.

doi:https://doi.org/10.1155/2014/160519

Advances in Materials Science and Engineering

On this page

Abstract Introduction Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2014 | Article ID 160519 | https://doi.org/10.1155/2014/160519

Parametric Optimization of Squeeze Cast AC2A-Ni Coated Composite Using Taguchi Technique

A. R. Ravikumar,¹K. S. Amirthagadeswaran,²and P. Senthil³

Academic Editor: Martin Crimp

Received31 May 2013

Accepted29 Oct 2013

Published20 Jan 2014

Abstract

This paper mainly focusses on parametric optimization of squeeze cast AC2A Ni coated composite through Taguchi technique. Composite samples have been cast through squeeze casting for each experimental trial based on L16 orthogonal array. From analysis of variance (ANOVA), it has been found that reinforcement percentage, squeeze pressure, and pressure duration were the casting parameters making significant improvement in the mechanical properties such as hardness and ultimate tensile strength. Reinforcement percentage and squeeze pressure have been identified as the most influencing parameters from the percentage contribution analysis. The optimum parametric setting has been determined through Taguchi technique. It has been confirmed that AC2A-Ni coated composite obtained for the optimum parametric setting has exhibited better mechanical properties compared to the experimental trials.

1. Introduction

The increase in demand for light weight and energy efficient materials with high strength, stiffness, and wear resistance leads to the development of advanced materials like metal matrix composites (MMCs) [1–3]. Among the various matrix materials available, aluminium alloys are mostly employed in MMCs because of their light weight, economical viability, processing flexibility, corrosion resistance, high thermal conductivity, and heat treatment capability [4–6]. Particle reinforced aluminium metal matrix composites (PAMMCs) are the most attractive materials due to their improved strength, high modulus, and more resistance against wear and corrosion when compared to their monolithic alloy [7]. Even though specific strength of PAMMCs is not as high as that of continuous fiber reinforced MMCs, ease of processing, isotropic properties, and considerable cost make them potential candidates in various applications like aerospace, marine, military, and automobile [7, 8]. Moreover, the particle reinforcements reduce the troubles allied with manufacturing of continuous fiber reinforced MMCs such as fiber mismatch, fiber fracture, and heterogeneity in microstructure [9].

Oxides, carbides, nitrides, and borides are the various groups of ceramic reinforcements used in PAMMCs [10]. In the various groups, silicon carbide finds more application due to its low cost and easy availability [11]. In addition, SiC have been found to have excellent compatibility with the aluminium alloy matrix [12, 13].

MMCs are usually processed either by solid state processes (powder metallurgy) or liquid state processes (casting route) [14, 15]. In the former, distribution of the particle reinforcements is uniform and interfacial reactions can be controlled easily, but cost of the process is high. Casting is the most economical route of transferring the raw materials into the final near net shape and use of wide range of ceramic reinforcements is possible, but has difficulties like non uniform distribution of particles and extensive interfacial reactions [16]. Also the conventional casting has major drawbacks like porosities, hot tears, and so forth. Squeeze casting is known as very promising route of manufacturing near net shape MMCs economically in single step. In this process, solidification of melt takes place under high pressure, which eliminates formation of porosities caused by shrinkage and gas and also saves material by eliminating runner and riser. Moreover, shape tolerance, surface finish, and mechanical properties are highly improved with fine microstructure and adhesion of molten metal with reinforcement [11].

Seo and Kang [16] have reported that hardness and tensile strength of squeeze cast composite were improved with application of pressure up to 100 MPa. They have also noticed the fractures and split of many particles under an applied pressure of 130 MPa. Onat et al. [11] have noted that hardness of squeeze cast composite increased with the increase of volume fraction and squeeze pressure. Sukumaran et al. [17] have pointed out that squeeze cast composite has acquired mechanical properties which can be comparable with properties that are obtainable by hot working and also observed reduction in defect level due to applied pressure. Daoud et al. [18] have informed that application of squeeze pressure eliminated the excesses porosity and improved the hardness in the case of squeeze cast Al7075- Al₂O₃ composite.

Yue and Chadwick [19] have stated that there is no real value in manufacturing of particle reinforced composite castings with porosity, since the porosity dominates the mechanical responses during loading. Further, they declared that squeeze casting has a clear merit over its alternative techniques due to zero porosity. Suresh et al. [20] have identified that the squeeze pressure increased the mechanical properties of squeeze cast Al-Beryl composite compared to gravity cast composite. Kalkanli and Yilmaz [9] have observed that squeeze cast Al7075-SiC_p composite revealed a maximum tensile strength when reinforcing 10% SiC_p and also noticed that several samples were found with agglomerations. Kaynak and Boylu [21] have inferred that addition of Mg while processing squeeze cast Al-SiC_p composite improved the wettability which resulted in certain bonding at the matrix-particulate interface. But, insufficient interfacial bond strength was noted under high stress level, which initiated crack at the interface.

However, there exist several problems in producing good quality PAMMCs. The main problem is the high reactivity (interfacial reaction) of SiC_p with aluminium alloy to form aluminium carbide (Al₄C₃) which results in reinforcement degradation and reduction of composite strength. Another problem is poor wettability of ceramic particles in liquid aluminium alloy [22]. Particularly in Al-Si/SiC_p composites, less silicon content leads to enhanced interfacial reactions and lack of wettability at the interface of the reinforcement and Al matrix. Ren et al. [23] have showed that the composite exhibited poor wettability, higher porosity, and poor thermophysical properties when Si content of Al alloy was lower than 6%. Samuel et al. [15] have made comparison of four composites and stated that low silicon content in the aluminium alloy accelerated the formation of Al₄C₃, while high silicon content decelerated the same. According to the research works [5, 24, 25], it is evident that the formation of Al₄C₃ could be suppressed by having a matrix alloy containing higher silicon content.

Metallic coating of the reinforcement is one of the successful methods to reduce or eliminate the interfacial reactions and promote wettability between SiC_p and Al matrix. [5]. Tekmen and Cocen [26] have reported that squeeze cast Al alloy- (Al-7% Si-0.7% Mg) Ni coated SiC_p composite showed improvement in the interfacial bonding and elimination of Al₄C₃. Ramesh et al. [27, 28] have reported that uniform distribution and excellent interfacial bonding of silicon nitride particles were highly achieved by good wettability of Ni-P coated silicon nitride (Si₃N₄) particles with Al matrix during the preparation of Al6061-Si₃N₄ composite. Also, they have stated that both mechanical and tribological properties were considerably improved with Ni-P coating. Yu et al. [29] have stated that tensile strength of squeeze cast Al6061-Y₂O₃ coated Al₂O₃ composite could be improved by 27% when compared to the uncoated one. Dikici et al. [30] have studied the effect of particle sol-gel coating on SiC_p with A380 aluminium alloy composite and found clean and sharp interface between matrix and reinforcement. Ramesh et al. [31] have indicated that Ni-P coating on SiC_p showed an appreciable improvement in mechanical properties of Al6061-SiC_p composite.

From the literature, it was noted that Al- (less than 6%) Si alloy has not been considered as metal matrix with SiC_p through squeeze casting process. In this direction, AC2A aluminium alloy has been considered as matrix and Ni coated SiC_p as reinforcement for the production of squeeze cast AC2A-Ni coated SiC_p composite in this study. The chemical composition of AC2A as per Japanese Industrial Standard (JIS H5202) is given in Table 1.

AC2A alloy is widely used for producing automotive components such as brake cylinder, master cylinder, engine brackets, cylinder heads, and rear axle housings. Senthil and Amirthagadeswaran [32] have stated that squeeze casting is a very effective technique to process AC2A aluminium alloy for the production of brake cylinder with improved mechanical properties. It is expected that the mechanical properties may be increased further while processing this alloy with the addition of Ni coated SiC_p through squeeze casting. In order to improve the quality of castings, the casting parameters have to be carefully controlled and optimized. Taguchi technique was employed to find out the optimum parametric setting in this study.

2. Taguchi Technique

Taguchi technique is a powerful offline quality control concept used to design high quality systems. This technique offers a simple, systematic, and efficient way to optimize designs for improved performance and quality with reduced experimental time and cost [33, 34]. It utilizes robust design to solve lot of complex problems in manufacturing industries for product or process. The methodology is effective to deal with responses that are influenced by multivariables (parameters). This technique significantly reduces the number of experiments which are required to model the response function compared with the full factorial design of experiments. Further, this technique determines the most influential parameter of the system, which, on control, would result in significant improvement in the performance [25].

Taguchi technique employs a special design of orthogonal arrays to study the entire parameter space with only a small number of well balanced experiments and signal-noise () ratio as the quality characteristic of choice [35]. ratio is the ratio of the mean (signal) to the standard deviation (noise). The quality characteristics normally used are lower-the-better, larger-the-better, and nominal-the-best [36]. This technique is executed with the following steps.(i)Identify process parameters influencing output response of the process.(ii)Choose a suitable orthogonal array to carry out experiments.(iii)Examine the results to find out optimum parametric setting.(iv)Execute a statistical analysis of variance (ANOVA) to find significant parameters.(v)Run a confirmatory test using the optimum setting.

Five casting parameters, namely, reinforcement percentage, pouring temperature, mould temperature, squeeze pressure, and pressure duration, each at four levels were selected. A four level L₁₆(4⁵) orthogonal array with sixteen experimental runs was selected. Hardness and ultimate tensile strength were considered as quality characteristics with the concept of the “larger the better.” Mathematical equation of the ratio used for these types of response is given in where and is the response value for an experimental condition repeated times.

3. Experiments and Tests

3.1. Experimental Details

3.1.1. Ni Coating on SiC_p

Silicon carbide powder with particle size of range 5–40 μm was used as reinforcement. Silicon carbide particles were cleaned, sensitized, and activated with acetone, SnCl₂, and PdCl₂, respectively. Then, the activated particles were coated by using electroless plating bath containing 25 g NiSO₄·6H₂O, 9 g NaC₂H₃O₂, 23 g NaH₃PO₂·H₂O, and 0.001 g Pb²⁺ dissolved in 1litre distilled water (Figure 1).

3.1.2. Squeeze Casting of AC2A-Ni Coated SiC_p Composite

AC2A aluminium alloy was used as metal matrix. 5 Kg AC2A was melted in a graphite crucible by using an electric induction furnace and we waited until a homogeneous liquid phase is obtained. During melting, the surface of the melt was covered by coverall flux in order to avoid the entrapment of gases into the melt. After getting homogeneous liquid phase, the melt was degassed by using hexachloroethane degasser. The pure melt after degassing was agitated by using mechanical stirrer rotating at a speed of 300 rpm to create fine vortex. While stirring constantly for 10 minutes, Ni coated SiC particles were gradually added into the fine vortex. The addition of reinforcement is shown in Figure 2.

Blue Star universal testing machine (Model: UTE-40) of 40 tonne capacity with little modification shown in Figure 3 was employed to apply pressure on the liquid melt in the mould cavity for direct squeeze casting. SG400 spheroidal graphite iron (split mould material), EN8 alloy steel (punch material), and Dycote D140 (coating material on surfaces of mould cavity) were used during the conduct of experiments. Two electrical heaters were employed to preheat split mould assembly and punch. The composite melt was poured into the preheated mould cavity. Pressure was applied on the melt through the preheated punch and maintained until solidification was completed. Punch was then withdrawn and the casting was separated from the mould assembly.

3.1.3. Parametric Constraints

The reinforcement (Ni coated SiC_p) less than 2.5 wt% did not show any appreciable improvement in mechanical properties and the reinforcement greater than 10 wt% led to agglomerations in the castings. So, the addition of reinforcement was varied from 2.5 wt% to 10 wt%. Pouring temperature of 675°C was required for the effective reinforcement of SiC_p in the melt. When pouring temperature was raised above 750°C, Ni coating on SiC_p got degraded. The mould assembly was designed to withstand maximum squeeze pressure of 125 MPa. It was observed that there was an existence of micro pores in the castings for pressures below 50 MPa. The mould temperatures below 200°C resulted in premature solidification and temperatures above 350°C increased solidification time leading to loss in production and decreased life of the mould assembly. It was experimentally found that pressure duration from 25 seconds to 55 seconds exhibited an appreciable improvement in mechanical properties. Hence, the bounds for all these casting parameters were set as follows. Reinforcement weight percentage, (%): , pouring temperature, (°C): , squeeze pressure, (MPa): , mould temperature, (°C): , pressure duration, (s): .

All process parameters were fixed at four levels within the above bounds to conduct experiments according to L₁₆ (4⁵) orthogonal array. The details of all parameters and their levels are given in Table 2. Brake cylinder samples were cast for each experimental condition based on the array. A set of samples is shown in Figure 4.

3.2. Testing

3.2.1. Hardness Test

For Brinell hardness test, 250 kg load was applied through a ball indenter of 5 mm diameter on polished surface of the specimen and hardness values (BHN) were measured in four spots of functional areas as shown in Figure 5.

3.2.2. Tensile Test

INSTRON universal testing machine was employed for performing tensile test on the specimens. Four tensile test specimens, each of 4.53 mm diameter with a gauge length of 16 mm, were prepared and readings were noted.

4. Results and Discussion

4.1. Ratio Response

The ratios for hardness and ultimate tensile strength were calculated using (1) for each parametric setting and their values are given in Table 3.

Mean value of ratios was also calculated for hardness and ultimate tensile strength and their values () are given in Table 3. Consider where (here ) and is ratio for th parametric setting. In order to find optimum level of the process parameters, average ratio response was estimated for every level of each parameter and the corresponding details are given in Tables 4 and 5. Based on the highest value of ratio, an optimum level for each parameter (: 4th level; : 3rd level; : 3rd level; : 2nd level; and : 3rd level) was noted. The optimum casting condition (reinforcement percentage of 10%, pouring temperature of 725°C, squeeze pressure of 100 MPa, mould temperature of 250°C, and pressure duration of 45 s) was noted to be same for both output responses. This is due to both output responses being often related in all aluminium alloy composites. The response graphs shown in Figures 6 and 7 described the variation of each process control parameter on the performance of the squeeze casting process. From the response graphs, it was observed that parameters and showed lesser variations on the output responses compared to other parameters. Therefore, analysis of variance (ANOVA) and test were used to analyze the experimental data.

4.2. Analysis of Variance

Analysis of variance was performed on signal to noise ratios to find the significance of the process control parameters and their contribution in the process performance. The following terms were calculated and their values are given in Tables 6 and 7.(i)Sum of squares due to mean: (ii)Sum of squares due to parameter : Similarly, sum of squares due to parameters , , , and were calculated. Sum of squares due to parameters and were found to be less in this study. Therefore, their effects on the output responses were assumed to be negligible and treated as an error (pooled error). Sum of squares due to pooled error was also calculated as follows: (iii)Total sum of squares:

(iv)Degree of freedom for parameter: . Degree of freedom for pooled error: .(v)Mean sum of squares due to parameter : Similarly, mean sum of squares for all other parameters and pooled error were calculated.(vi) ratio for parameter ,

Similarly, ratio was calculated for parameters and . The calculated ratio for parameters , , and was found to be greater than the distribution value ( at 5% level of significance). Therefore, the parameters , , and were confirmed as significant parameters in this study.(vii)Pure sum of squares due to parameter : (viii)Percentage contribution of parameter , Similarly, pure sum of squares and percentage contribution of parameters , , and pooled error were calculated. The percentage contribution of pooled error was noted to be less than 5% for both output responses in this study. The percentage contribution of all significant parameters is clearly shown in Figure 8.

4.3. Predicted Mean and Confidence Interval

Predicted mean for hardness and ultimate tensile strength and confidence interval (CI) for the predicted mean were determined by using the following: where and = (Number of experiments)/(1 + Total DOF associated with ).

The confidence interval for hardness and ultimate tensile strength was noted to be ±0.37 dB and 0.36 dB, respectively, at 5% level of significance. The predicted mean of hardness (43.26 dB) showed the variation from 42.89 to 43.63 dB. The predicted mean of ultimate tensile strength (52.31 dB) showed the variation from 51.95 to 52.67 dB.

4.4. Confirmation Experiments

Two samples were made for the optimum parametric setting. The values of hardness and ultimate tensile strength measured in the functional volume were found to be 147, 141, 145, and 144 BHN and 419, 402, 414, and 410 MPa, respectively, and their ratios were 43.18 dB and 52.28 dB, respectively. These ratio values were found within the confidence interval limits. A comparison was made for different casting conditions (: 0.1 MPa , , , and ) in the microstructural aspect as shown in Figure 9. The castings obtained for optimum condition showed better grain refinement and uniform distribution of reinforcements when compared with other conditions.

5. Conclusion

Taguchi technique was employed to find the optimum parametric setting of squeeze casting process for producing high quality castings of AC2A-Ni coated SiC_p Composite. The optimum parametric setting was found as follows: reinforcement percentage: 10%, pouring temperature: 725°C, squeeze pressure: 100 MPa, mould temperature: 250°C, pressure duration: 45 seconds.

This setting was verified through the confirmation experiments. The castings produced for the optimum setting were found to be defects free and sound. From the ANOVA, reinforcement percentage, squeeze pressure, and pressure duration were identified as significant casting parameters in this study. From the percentage contribution analysis, it was noted that reinforcement percentage and squeeze pressure were the most important parameters for the improvement of mechanical properties.

Nomenclature

BHN:	Brinell hardness number
DOF:	Degree of freedom
DOE:	Design of experiments
gpl:	Gram per litre
MSS:	Mean sum of squares
:	Number of experiments
:	Number of observations
PC:	Percentage contribution
PSS:	Pure sum of squares
R₁:	Readings measured in spot P
R₂:	Readings measured in spot Q
R₃:	Readings measured in spot R
R₄:	Readings measured in spot S
SS:	Sum of squares
TSS:	Total sum of squares.

Conflict of Interests

The authors declare that they have no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors are thankful to M/S Unique Shell Mould (India) Pvt. Ltd., Coimbatore, and Sri Krishna College of Engineering and Technology, Coimbatore, for providing research facilities to carry out this research work.

References

F. Toptan, A. Kilicarslan, A. Karaaslan, M. Cigdem, and I. Kerti, “Processing and microstructural characterisation of AA 1070 and AA 6063 matrix B₄C_p reinforced composites,” Materials and Design, vol. 31, no. 1, pp. S87–S91, 2010.
View at: Publisher Site | Google Scholar
N. C. Murmu, “Comparison of response surface methodology and artificial neural network technique for prediction of wear of 6061 al-alloy—SiCp composite,” International Journal of Mechanical and Materials Engineering, vol. 6, no. 3, pp. 437–444, 2011.
View at: Google Scholar
J. Du, Y. Liu, S. Yu, and W. Li, “Effect of heat-treatment on friction and wear properties of Al₂O₃ and carbon short fibres reinforced AlSi12CuMgNi hybrid composites,” Wear, vol. 262, no. 11-12, pp. 1289–1295, 2007.
View at: Publisher Site | Google Scholar
Ü. Cöcen and K. Önel, “Ductility and strength of extruded SiCp/aluminium-alloy composites,” Composites Science and Technology, vol. 62, no. 2, pp. 275–282, 2002.
View at: Publisher Site | Google Scholar
T. P. D. Rajan, R. M. Pillai, and B. C. Pai, “Reinforcement coatings and interfaces in aluminium metal matrix composites,” Journal of Materials Science, vol. 33, no. 14, pp. 3491–3503, 1998.
View at: Google Scholar
A. Mazahery and M. O. Shabani, “Influence of the hard coated B₄C particulates on wear resistance of Al-Cu alloys,” Composites B, vol. 43, no. 3, pp. 1302–1308, 2012.
View at: Publisher Site | Google Scholar
A. Canakci and F. Arslan, “Abrasive wear behaviour of B4C particle reinforced Al2024 MMCs,” International Journal of Advanced Manufacturing Technology, vol. 63, pp. 785–795, 2012.
View at: Publisher Site | Google Scholar
A. Onat, “Mechanical and dry sliding wear properties of silicon carbide particulate reinforced aluminium-copper alloy matrix composites produced by direct squeeze casting method,” Journal of Alloys and Compounds, vol. 489, no. 1, pp. 119–124, 2010.
View at: Publisher Site | Google Scholar
A. Kalkanli and S. Yilmaz, “Synthesis and characterization of aluminum alloy 7075 reinforced with silicon carbide particulates,” Materials and Design, vol. 29, no. 4, pp. 775–780, 2008.
View at: Publisher Site | Google Scholar
F. Toptan, I. Kerti, and L. A. Rocha, “Reciprocal dry sliding wear behavior of B₄C_p reinforced aluminium alloy matrix composites,” Wear, vol. 290-291, pp. 74–85, 2012.
View at: Google Scholar
A. Onat, H. Akbulut, and F. Yilmaz, “Production and characterisation of silicon carbide particulate reinforced aluminium-copper alloy matrix composites by direct squeeze casting method,” Journal of Alloys and Compounds, vol. 436, no. 1-2, pp. 375–382, 2007.
View at: Publisher Site | Google Scholar
H. Mindivan, E. Sabri Kayali, and H. Cimenoglu, “Tribological behavior of squeeze cast aluminum matrix composites,” Wear, vol. 265, no. 5-6, pp. 645–654, 2008.
View at: Publisher Site | Google Scholar
T. Ma, H. Yamaura, D. A. Koss, and R. C. Voigt, “Dry sliding wear behavior of cast SiC-reinforced Al MMCs,” Materials Science and Engineering A, vol. 360, no. 1-2, pp. 116–125, 2003.
View at: Publisher Site | Google Scholar
S. M. S. Reihani, “Processing of squeeze cast Al6061-30vol% SiC composites and their characterization,” Materials and Design, vol. 27, no. 3, pp. 216–222, 2006.
View at: Publisher Site | Google Scholar
A. M. Samuel, H. Liu, and F. H. Samuel, “On the castability of Al-Si/SiC particle-reinforced metal-matrix composites: factors affecting fluidity and soundness,” Composites Science and Technology, vol. 49, no. 1, pp. 1–12, 1993.
View at: Google Scholar
Y.-H. Seo and C.-G. Kang, “The effect of applied pressure on particle-dispersion characteristics and mechanical properties in melt-stirring squeeze-cast SiCp/Al composites,” Journal of Materials Processing Tech, vol. 55, no. 3-4, pp. 370–379, 1995.
View at: Google Scholar
K. Sukumaran, K. K. Ravikumar, S. G. K. Pillai et al., “Studies on squeeze casting of Al 2124 alloy and 2124-10% SiCp metal matrix composite,” Materials Science and Engineering A, vol. 490, no. 1-2, pp. 235–241, 2008.
View at: Publisher Site | Google Scholar
A. Daoud, M. T. Abou El-Khair, and A. N. Abdel-Azim, “Effect of Al₂O₃ particles on the microstructure and sliding wear of 7075 Al alloy manufactured by squeeze casting method,” Journal of Materials Engineering and Performance, vol. 13, no. 2, pp. 135–143, 2004.
View at: Publisher Site | Google Scholar
T. M. Yue and G. A. Chadwick, “Squeeze casting of light alloys and their composites,” Journal of Materials Processing Technology, vol. 58, no. 2-3, pp. 302–307, 1996.
View at: Google Scholar
K. R. Suresh, H. B. Niranjan, P. M. Jebaraj, and M. P. Chowdiah, “Tensile and wear properties of aluminum composites,” Wear, vol. 255, no. 1–6, pp. 638–642, 2003.
View at: Publisher Site | Google Scholar
C. Kaynak and S. Boylu, “Effects of SiC particulates on the fatigue behaviour of an Al-alloy matrix composite,” Materials and Design, vol. 27, no. 9, pp. 776–782, 2006.
View at: Publisher Site | Google Scholar
C. A. Leon and R. A. L. Drew, “Preparation of nickel-coated powders as precursors to reinforce MMCs,” Journal of Materials Science, vol. 35, no. 19, pp. 4763–4768, 2000.
View at: Publisher Site | Google Scholar
S. Ren, X. He, X. Qu, I. S. Humail, and Y. Li, “Effect of Mg and Si in the aluminum on the thermo-mechanical properties of pressureless infiltrated SiCp/Al composites,” Composites Science and Technology, vol. 67, no. 10, pp. 2103–2113, 2007.
View at: Publisher Site | Google Scholar
O. Beffort, S. Long, C. Cayron, J. Kuebler, and P.-A. Buffat, “Alloying effects on microstructure and mechanical properties of high volume fraction SiC-particle reinforced Al-MMCs made by squeeze casting infiltration,” Composites Science and Technology, vol. 67, no. 3-4, pp. 737–745, 2007.
View at: Publisher Site | Google Scholar
S. Lee, D. Kwon, and D. Suh, “Microstructure and fracture of SiC-particulate-reinforced cast A356 aluminum alloy composites,” Metallurgical and Materials Transactions A, vol. 27, no. 12, pp. 3893–3901, 1996.
View at: Google Scholar
C. Tekmen and U. Cocen, “Squeeze casting of Ni coated SiC particle reinforced Al based composite,” Journal of Composite Materials, vol. 42, no. 13, pp. 1271–1279, 2008.
View at: Publisher Site | Google Scholar
C. S. Ramesh, R. Keshavamurthy, B. H. Channabasappa, and A. Ahmed, “Microstructure and mechanical properties of Ni-P coated Si₃N₄ reinforced Al6061 composites,” Materials Science and Engineering A, vol. 502, no. 1-2, pp. 99–106, 2009.
View at: Publisher Site | Google Scholar
C. S. Ramesh, R. Keshavamurthy, B. H. Channabasappa, and S. Pramod, “Friction and wear behavior of Ni-P coated Si₃N₄ reinforced Al6061 composites,” Tribology International, vol. 43, no. 3, pp. 623–634, 2010.
View at: Publisher Site | Google Scholar
Z. Yu, G. Wu, L. Jiang, and D. Sun, “Effect of coating Al₂O₃ reinforcing particles on the interface and mechanical properties of 6061 alloy aluminium matrix composites,” Materials Letters, vol. 59, no. 18, pp. 2281–2284, 2005.
View at: Publisher Site | Google Scholar
B. Dikici, C. Tekmen, O. Yigit, M. Gavgali, and U. Cocen, “Detrimental effect of particle sol-gel coating on the corrosion behavior of A380-SiC composite,” Corrosion Science, vol. 51, no. 3, pp. 469–476, 2009.
View at: Publisher Site | Google Scholar
C. S. Ramesh, R. Keshavamurthy, and G. J. Naveen, “Effect of extrusion ratio on wear behaviour of hot extruded Al6061-SiCp (Ni-P coated) composites,” Wear, vol. 271, no. 9-10, pp. 1868–1877, 2011.
View at: Publisher Site | Google Scholar
P. Senthil and K. S. Amirthagadeswaran, “Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method,” Journal of Mechanical Science and Technology, vol. 26, no. 4, pp. 1141–1147, 2012.
View at: Publisher Site | Google Scholar
S. Basavarajappa, G. Chandramohan, and J. Paulo Davim, “Application of Taguchi techniques to study dry sliding wear behaviour of metal matrix composites,” Materials and Design, vol. 28, no. 4, pp. 1393–1398, 2007.
View at: Publisher Site | Google Scholar
U. Soy, F. Ficici, and A. Demir, “Evaluation of the Taguchi method for wear behavior of Al/SiC/B₄C composites,” Journal of Composite Materials, vol. 46, no. 7, pp. 851–859, 2012.
View at: Publisher Site | Google Scholar
S. Palanisamy, S. Ramanathan, and R. Rangaraj, “Analysis of dry sliding wear behaviour of Aluminium-Fly Ash composites: the Taguchi approach,” Advances in Mechanical Engineering, vol. 2013, Article ID 658085, 10 pages, 2013.
View at: Publisher Site | Google Scholar
P. Vijian and V. P. Arunachalam, “Optimization of squeeze cast parameters of LM6 aluminium alloy for surface roughness using Taguchi method,” Journal of Materials Processing Technology, vol. 180, no. 1–3, pp. 161–166, 2006.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2014 A. R. Ravikumar et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1652

Downloads

1595

Citations