Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2015, Article ID 235424, 8 pages
http://dx.doi.org/10.1155/2015/235424
Research Article

Evaluation of Interface Shear Strength Properties of Geogrid Reinforced Foamed Recycled Glass Using a Large-Scale Direct Shear Testing Apparatus

1Department of Civil and Construction Engineering, Swinburne University of Technology, Melbourne, VIC 3122, Australia
2Suranaree University of Technology, Nakhon Ratchasima, Thailand
3Southeast University, Nanjing 210096, China
4State Key Laboratory of Ocean Engineering, School of Naval Architecture, Ocean, and Civil Engineering, Shanghai Jiao Tong University, Shanghai 200240, China

Received 2 June 2015; Revised 8 October 2015; Accepted 11 October 2015

Academic Editor: Luigi Nicolais

Copyright © 2015 Arul Arulrajah et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. Horpibulsuk, V. Munsrakest, A. Udomchai, A. Chinkulkijniwat, and A. Arulrajah, “Strength of sustainable non-bearing masonry units manufactured from calcium carbide residue and fly ash,” Construction and Building Materials, vol. 71, pp. 210–215, 2014. View at Publisher · View at Google Scholar · View at Scopus
  2. S. Horpibulsuk, A. Wijitchot, A. Nerimitknornburee, S. L. Shen, and C. Suksiripattanapong, “Factors influencing unit weight and strength of lightweight cemented clay,” Quarterly Journal of Engineering Geology and Hydrogeology, vol. 47, no. 1, pp. 101–109, 2014. View at Publisher · View at Google Scholar · View at Scopus
  3. A. Athanasopoulos - Zekkos, K. Lamote, and G. A. Athanasopoulos, “Use of EPS geofoam compressible inclusions for reducing the earthquake effects on yielding earth retaining structures,” Soil Dynamics and Earthquake Engineering, vol. 41, pp. 59–71, 2012. View at Publisher · View at Google Scholar · View at Scopus
  4. A. Deng and Y. Xiao, “Measuring and modeling proportion-dependent stress-strain behavior of EPS-sand mixture,” International Journal of Geomechanics, vol. 10, no. 6, pp. 214–222, 2010. View at Publisher · View at Google Scholar · View at Scopus
  5. O. L. Ertugrul and A. C. Trandafir, “Reduction of lateral earth forces acting on rigid nonyielding retaining walls by EPS geofoam inclusions,” Journal of Materials in Civil Engineering, vol. 23, no. 12, pp. 1711–1718, 2011. View at Publisher · View at Google Scholar · View at Scopus
  6. L.-K. Lin, L.-H. Chen, and R. H. L. Chen, “Evaluation of geofoam as a geotechnical construction material,” Journal of Materials in Civil Engineering, vol. 22, no. 2, pp. 160–170, 2010. View at Publisher · View at Google Scholar · View at Scopus
  7. A. C. Trandafir and B. A. Erickson, “Stiffness degradation and yielding of EPS geofoam under cyclic loading,” Journal of Materials in Civil Engineering, vol. 24, no. 1, pp. 119–124, 2012. View at Publisher · View at Google Scholar · View at Scopus
  8. Y. Zou, C. J. Leo, and H. Wong, “Time dependent viscoelastic behaviour of Eps geofoam,” Applied Mechanics and Materials, vol. 330, pp. 1095–1099, 2013. View at Google Scholar · View at Scopus
  9. A. Neramitkornburi, S. Horpibulsuk, S. L. Shen, A. Arulrajah, and M. M. Disfani, “Engineering properties of lightweight cellular cemented clay-fly ash material,” Soils and Foundations, vol. 55, no. 2, pp. 471–783, 2015. View at Publisher · View at Google Scholar
  10. A. Neramitkornburi, S. Horpibulsuk, S. L. Shen, A. Chinkulkijniwat, A. Arulrajah, and M. M. Disfani, “Durability against wetting-drying cycles of sustainable lightweight cellular cemented construction material comprising clay and fly ash wastes,” Construction and Building Materials, vol. 77, pp. 41–49, 2015. View at Publisher · View at Google Scholar · View at Scopus
  11. C. Teerawattanasuk, P. Voottipruex, and S. Horpibulsuk, “Mix design charts for lightweight cellular cemented Bangkok clay,” Applied Clay Science, vol. 104, pp. 318–323, 2015. View at Publisher · View at Google Scholar · View at Scopus
  12. V. Cecich, L. Gonzales, A. Hoisaeter, J. Williams, and K. Reddy, “Use of shredded tires as lightweight backfill material for retaining structures,” Waste Management and Research, vol. 14, no. 5, pp. 433–451, 1996. View at Publisher · View at Google Scholar · View at Scopus
  13. I. F. Hodgson, S. P. Beales, and M. J. Curd, “Use of tyre bales as lightweight fill for the A421 improvements scheme near Bedford, UK,” Geological Society Engineering Geology Special Publication, vol. 26, no. 1, pp. 101–108, 2012. View at Publisher · View at Google Scholar · View at Scopus
  14. S. N. M. Tafreshi, G. T. Mehrjardi, and A. R. Dawson, “Buried pipes in rubber-soil backfilled trenches under cyclic loading,” Journal of Geotechnical and Geoenvironmental Engineering, vol. 138, no. 11, pp. 1346–1356, 2012. View at Publisher · View at Google Scholar · View at Scopus
  15. A. Nakhaei, S. M. Marandi, S. Sani Kermani, and M. H. Bagheripour, “Dynamic properties of granular soils mixed with granulated rubber,” Soil Dynamics and Earthquake Engineering, vol. 43, pp. 124–132, 2012. View at Publisher · View at Google Scholar · View at Scopus
  16. A. Arulrajah, J. Piratheepan, M. M. Disfani, and M. W. Bo, “Geotechnical and geoenvironmental properties of recycled construction and demolition materials in pavement subbase applications,” Journal of Materials in Civil Engineering, vol. 25, no. 8, pp. 1077–1088, 2013. View at Publisher · View at Google Scholar · View at Scopus
  17. L. R. Hoyos, A. J. Puppala, and C. A. Ordonez, “Characterization of cement-fiber-treated reclaimed asphalt pavement aggregates: preliminary investigation,” Journal of Materials in Civil Engineering, vol. 23, no. 7, pp. 977–989, 2011. View at Publisher · View at Google Scholar · View at Scopus
  18. A. J. Puppala, L. R. Hoyos, and A. K. Potturi, “Resilient moduli response of moderately cement-treated reclaimed asphalt pavement aggregates,” Journal of Materials in Civil Engineering, vol. 23, no. 7, pp. 990–998, 2011. View at Publisher · View at Google Scholar · View at Scopus
  19. R. Taha, A. Al-Harthy, K. Al-Shamsi, and M. Al-Zubeidi, “Cement stabilization of reclaimed asphalt pavement aggregate for road bases and subbases,” Journal of Materials in Civil Engineering, vol. 14, no. 3, pp. 239–245, 2002. View at Publisher · View at Google Scholar · View at Scopus
  20. M. A. Rahman, A. Arulrajah, J. Piratheepan, M. W. Bo, and M. A. Imteaz, “Resilient modulus and permanent deformation responses of geogrid-reinforced construction and demolition materials,” Journal of Materials in Civil Engineering, vol. 26, no. 3, pp. 512–519, 2014. View at Publisher · View at Google Scholar · View at Scopus
  21. J. Wartman, D. G. Grubb, and A. S. M. Nasim, “Select engineering characteristics of crushed glass,” Journal of Materials in Civil Engineering, vol. 16, no. 6, pp. 526–539, 2004. View at Publisher · View at Google Scholar · View at Scopus
  22. K. R. Reddy, H. Hettiarachchi, N. S. Parakalla, J. Gangathulasi, and J. E. Bogner, “Geotechnical properties of fresh municipal solid waste at Orchard Hills Landfill, USA,” Waste Management, vol. 29, no. 2, pp. 952–959, 2009. View at Publisher · View at Google Scholar · View at Scopus
  23. D. Zekkos, J. D. Bray, E. Kavazanjian Jr. et al., “Unit weight of municipal solid waste,” Journal of Geotechnical and Geoenvironmental Engineering, vol. 132, no. 10, pp. 1250–1261, 2006. View at Publisher · View at Google Scholar · View at Scopus
  24. C. Phetchuay, S. Horpibulsuk, C. Suksiripattanapong, A. Chinkulkijniwat, A. Arulrajah, and M. M. Disfani, “Calcium carbide residue: alkaline activator for clay-fly ash geopolymer,” Construction and Building Materials, vol. 69, pp. 285–294, 2014. View at Publisher · View at Google Scholar · View at Scopus
  25. A. Arulrajah, M. M. Disfani, S. Horpibulsuk, C. Suksiripattanapong, and N. Prongmanee, “Physical properties and shear strength responses of recycled construction and demolition materials in unbound pavement base/subbase applications,” Construction and Building Materials, vol. 58, pp. 245–257, 2014. View at Publisher · View at Google Scholar · View at Scopus
  26. M. M. Disfani, A. Arulrajah, H. Haghighi, A. Mohammadinia, and S. Horpibulsuk, “Flexural beam fatigue strength evaluation of crushed brick as a supplementary material in cement stabilized recycled concrete aggregates,” Construction and Building Materials, vol. 68, pp. 667–676, 2014. View at Publisher · View at Google Scholar · View at Scopus
  27. Y.-J. Du, N.-J. Jiang, S.-Y. Liu, F. Jin, D. N. Singh, and A. J. Puppala, “Engineering properties and microstructural characteristics of cement-stabilized zinc-contaminated kaolin,” Canadian Geotechnical Journal, vol. 51, no. 4, pp. 289–302, 2014. View at Publisher · View at Google Scholar · View at Scopus
  28. D. G. Grubb, P. M. Gallagher, J. Wartman, Y. Liu, and M. Carnivale III, “Laboratory evaluation of crushed glass-dredged material blends,” Journal of Geotechnical and Geoenvironmental Engineering, vol. 132, no. 5, pp. 562–576, 2006. View at Publisher · View at Google Scholar · View at Scopus
  29. A. Kampala, S. Horpibulsuk, A. Chinkullijniwat, and S.-L. Shen, “Engineering properties of recycled calcium carbide residue stabilized clay as fill and pavement materials,” Construction and Building Materials, vol. 46, pp. 203–210, 2013. View at Publisher · View at Google Scholar · View at Scopus
  30. A. Kampala, S. Horpibulsuk, N. Prongmanee, and A. Chinkulkijniwat, “Influence of wet-dry cycles on compressive strength of calcium carbide residue-fly ash stabilized clay,” Journal of Materials in Civil Engineering, vol. 26, no. 4, pp. 633–643, 2014. View at Publisher · View at Google Scholar · View at Scopus
  31. T. L. Landris, “Recycled glass and dredged materials,” Engineer Research and Development Center Report ERDC TN-DOER-T8, US Army Corps of Engineers, Vicksburg, Miss, USA, 2007. View at Google Scholar
  32. M. A. Rahman, M. A. Imteaz, A. Arulrajah, J. Piratheepan, and M. M. Disfani, “Recycled construction and demolition materials in permeable pavement systems: geotechnical and hydraulic characteristics,” Journal of Cleaner Production, vol. 90, pp. 183–194, 2015. View at Publisher · View at Google Scholar · View at Scopus
  33. A. Arulrajah, M. A. Rahman, J. Piratheepan, M. W. Bo, and M. A. Imteaz, “Evaluation of interface shear strength properties of geogrid-reinforced construction and demolition materials using a modified large-scale direct shear testing apparatus,” Journal of Materials in Civil Engineering, vol. 26, no. 5, pp. 974–982, 2014. View at Publisher · View at Google Scholar · View at Scopus
  34. F. B. Ferreira, C. S. Vieira, and M. L. Lopes, “Direct shear behaviour of residual soil-geosynthetic interfaces—influence of soil moisture content, soil density and geosynthetic type,” Geosynthetics International, vol. 22, no. 3, pp. 257–272, 2015. View at Google Scholar
  35. C. S. Vieira and P. M. Pereira, “Interface shear properties of geosynthetics and construction and demolition waste from large-scale direct shear tests,” Geosynthetics International, 2015. View at Publisher · View at Google Scholar
  36. P. Jana, V. Fierro, and A. Celzard, “Ultralow cost reticulated carbon foams from household cleaning pad wastes,” Carbon, vol. 62, pp. 517–520, 2013. View at Publisher · View at Google Scholar · View at Scopus
  37. G. Wang, L. Sha, and F. Jin, “Study on the strength properties and failure mode of recycled sludge lightweight soil,” Applied Mechanics and Materials, vol. 275–277, pp. 1281–1284, 2013. View at Publisher · View at Google Scholar · View at Scopus
  38. A. Arulrajah, M. M. Disfani, F. Maghoolpilehrood et al., “Engineering and environmental properties of foamed recycled glass as a lightweight engineering material,” Journal of Cleaner Production, vol. 94, pp. 369–375, 2015. View at Publisher · View at Google Scholar · View at Scopus
  39. A. Arulrajah, M. M. Disfani, H. Haghighi, A. Mohammadinia, and S. Horpibulsuk, “Modulus of rupture evaluation of cement stabilized recycled glass/recycled concrete aggregate blends,” Construction and Building Materials, vol. 84, pp. 146–155, 2015. View at Publisher · View at Google Scholar
  40. A. Arulrajah, M. M. Y. Ali, M. M. Disfani, and S. Horpibulsuk, “Recycled-glass blends in pavement base/subbase applications: laboratory and field evaluation,” Journal of Materials in Civil Engineering, vol. 26, no. 7, Article ID 04014025, 2014. View at Publisher · View at Google Scholar · View at Scopus
  41. M. A. Rahman, M. Imteaz, A. Arulrajah, and M. M. Disfani, “Suitability of recycled construction and demolition aggregates as alternative pipe backfilling materials,” Journal of Cleaner Production, vol. 66, pp. 75–84, 2014. View at Publisher · View at Google Scholar · View at Scopus
  42. A. Arulrajah, M. M. Y. Ali, M. M. Disfani, J. Piratheepan, and M. W. Bo, “Geotechnical performance of recycled glass-waste rock blends in footpath bases,” Journal of Materials in Civil Engineering, vol. 25, no. 5, pp. 653–661, 2013. View at Publisher · View at Google Scholar · View at Scopus
  43. F. Ahmad, D. Mujah, H. Hazarika, and A. Safari, “Assessing the potential reuse of recycled glass fibre in problematic soil applications,” Journal of Cleaner Production, vol. 35, pp. 102–107, 2012. View at Publisher · View at Google Scholar · View at Scopus
  44. D. Mujah, F. Ahmad, H. Hazarika, and A. Safari, “Evaluation of the mechanical properties of recycled glass fibers-derived three dimensional geomaterial for ground improvement,” Journal of Cleaner Production, vol. 52, pp. 495–503, 2013. View at Publisher · View at Google Scholar · View at Scopus
  45. H. R. Fernandes, D. U. Tulyaganov, and J. M. F. Ferreira, “Production and characterisation of glass ceramic foams from recycled raw materials,” Advances in Applied Ceramics, vol. 108, no. 1, pp. 9–13, 2009. View at Publisher · View at Google Scholar · View at Scopus
  46. I. Ponsot and E. Bernardo, “Self glazed glass ceramic foams from metallurgical slag and recycled glass,” Journal of Cleaner Production, vol. 59, pp. 245–250, 2013. View at Publisher · View at Google Scholar · View at Scopus
  47. G. Bumanis, D. Bajare, J. Locs, and A. Korjakins, “Alkali-silica reactivity of foam glass granules in structure of lightweight concrete,” Construction and Building Materials, vol. 47, pp. 274–281, 2013. View at Publisher · View at Google Scholar · View at Scopus
  48. H. W. Guo, Z. X. Mo, P. Liu, and D. N. Gao, “Improved mechanical property of foam glass composites toughened by mullite fiber,” Applied Mechanics and Materials, vol. 357–360, pp. 1370–1373, 2013. View at Publisher · View at Google Scholar · View at Scopus
  49. L. K. Kazantseva, “Particulars of foam glass manufacture from zeolite-alkali batch,” Glass and Ceramics, vol. 70, pp. 277–281, 2013. View at Google Scholar
  50. K. Pawanawichian, W. Thiemsorn, A. Wannagon, and P. Laoarun, “Fabrication of glass foams from industrial wastes used as insulating board,” Advanced Materials Research, vol. 770, pp. 205–208, 2013. View at Publisher · View at Google Scholar · View at Scopus
  51. Q. Wang, N. Wang, Z. Y. Ding, and T. J. Wu, “Influences of firing process system on foam glass properties,” Advanced Materials Research, vol. 721, pp. 258–261, 2013. View at Publisher · View at Google Scholar · View at Scopus
  52. L. Wu, Y. H. Zhao, R. F. Chen et al., “Effect of foaming temperature and holding time on foam glass,” in Advances in Manufacturing Science and Engineering, pp. 897–900, 2013. View at Google Scholar
  53. S. Horpibulsuk and A. Niramitkornburee, “Pullout resistance of bearing reinforcement embedded in sand,” Soils and Foundations, vol. 50, no. 2, pp. 215–226, 2010. View at Publisher · View at Google Scholar · View at Scopus
  54. C. Suksiripattanapong, S. Horpibulsuk, A. Chinkulkijniwat, and J. C. Chai, “Pullout resistance of bearing reinforcement embedded in coarse-grained soils,” Geotextiles and Geomembranes, vol. 36, pp. 44–54, 2013. View at Publisher · View at Google Scholar · View at Scopus
  55. VicRoads, Crushed Rock for Light Duty Base and Subbase Pavement, Section 813, VicRoads, Melbourne, Fla, USA, 2011.
  56. ASTM, “Standard test method for direct shear test of soils under consolidated drained conditions,” ASTM D3080/D3080M, ASTM International, West Conshohocken, Pa, USA, 2011. View at Google Scholar