Thermal Degradation Characteristics and Kinetics of Oxy Combustion of Corn Residues

Sittisun, Poramate; Tippayawong, Nakorn; Wattanasiriwech, Darunee

doi:https://doi.org/10.1155/2015/304395

Advances in Materials Science and Engineering

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2015 | Article ID 304395 | https://doi.org/10.1155/2015/304395

Thermal Degradation Characteristics and Kinetics of Oxy Combustion of Corn Residues

Poramate Sittisun,¹Nakorn Tippayawong,¹and Darunee Wattanasiriwech²

Academic Editor: Bart Partoens

Received26 Nov 2014

Accepted25 Mar 2015

Published05 Apr 2015

Abstract

Thermogravimetric analysis was used to investigate oxy combustion of corncob and stover. The biomass samples were heated from ambient temperature to 900°C at different heating rates of 10, 30, and 50 K/min. Both biomass samples showed similar weight loss patterns with three zones, corresponding to dehydration, devolatilization, and char combustion, but displayed different degradation temperatures. Increasing heating rate was found to shift the degradation patterns to higher temperatures. Decomposition rates of cob and stover may have been influenced by their lignocellulosic composition. The kinetic parameters of the thermal degradation process were also determined and compared using the Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose methods. Both methods were found to give similar values and patterns of activation energy against conversion fraction. The average values were found to be in similar magnitude to those reported in the literature, around 170 and 148 kJ/mol for cob and stover, respectively.

1. Introduction

Corn is an important agricultural crop in the world and the north of Thailand. It is widely planted for food production and animal feeding. After harvesting, there is a large amount of corn residues. Cob and stover (stalk and leaves) are the main residues. About 0.15 kg of cobs and 0.72 kg of stover are generated for every 1 kg of dry corn grains produced [1]. For Thailand, this resulted in the generation of about 0.73 and 3.50 million tons of corncob and stover in 2013 [2]. The residues are not normally utilized but left as waste or burned openly in the fields [3]. This open burning seriously pollutes the atmosphere, causes smog problem, affects human health, and also results in more CO₂ emission. These residues have great potential and should be harnessed as valuable feedstock for energy production.

The utility industry burning coal is the main sector responsible for major CO₂ emissions [4], which cause climate change and global warming. Utilization of biomass in coal fired power plants has gained great interest because of biomass’s carbon neutrality and ability to lower SO_x emissions. Biomass cofiring and oxygen combustion can have double effect in cutting down carbon emission from coal power plants.

Oxy combustion is an innovative combustion technology for burning fuel using pure oxygen instead of air. In this technique, because there is no nitrogen, NO_x is greatly reduced. The flue gas consists mainly of CO₂ and water vapor which can make it simpler for subsequent CO₂ capture and storage [5]. Combustion of biomass in highly oxidative atmosphere has not yet been widely investigated. Better understanding on its thermal degradation characteristics and burning kinetics is still needed. Thermogravimetric analysis is considered as a useful technique to access the thermal behavior and decomposition kinetics of biomass. It can determine thermal stability and fraction of volatile components of solid material by monitoring the change of weight that occurs as a sample is heated. There are many research works studied on potential biomass materials using thermogravimetric analysis [6–10]. It is well known that different decomposition atmospheres affect degradation behavior greatly. So far, most reported studies about the kinetics of biomass decomposition focused mainly on pyrolysis and combustion under nitrogen [11–14] and air atmospheres [15–18]. Only a few published works were related to biomass combustion under oxygen [19, 20]. Investigations on oxy combustion of corn residues are still very rare.

The aim of this research is to investigate the combustion behavior of corncob and stover under oxygen environment. Nonisothermal thermogravimetric analysis is used to evaluate thermal characteristics and kinetics of corn residues under highly oxidative condition. The findings should provide useful data for future development of efficient biomass combustion applications.

2. Materials and Methods

2.1. Sample Preparation

Samples of corncob and stover were collected from agriculture land in Nan, Thailand. They were naturally dried, crushed to small particle size, and sieved with 120 meshes. The samples of biomass material were subsequently kept in a ziplock plastic bag and stored at room temperature until they were needed for experiment. Typical properties of the samples are shown in Table 1.

2.2. Thermal Degradation Experiment

The experiments were performed using a Mettler Toledo thermogravimetric analyzer model TGA/SDTA 851e at 0.1 μg resolution. The initial weight of 10 mg was placed in an alumina crucible. It was heated from room temperature to the final temperature of 900°C with continuously purged high purity research grade oxygen at a flow rate of 20 mL/min. The heating rates were performed at 10, 30, and 50 K/min. The instrument continuously monitored and recorded weight loss data and temperature every second. Experiments were repeated at least two times for each condition.

2.3. Kinetic Analysis

Kinetic analysis was carried out to determine apparent activation energy for the associated thermal degradation. The analytical techniques can be divided into two classes: model-fitting and model-free (isoconversional) kinetics. The model-fitting method is based on a single heating rate, which is a disadvantage because the activation energy varies with the heating rate, due to mass and heat transfer effects. The isoconversional method is preferred by researchers because, with the use of multiple heating rates, it is sufficiently flexible to allow for a change in mechanism during reactions and mass transfer limitations [21]. Therefore, in this work the model-free kinetic methods by Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) were adopted.

The degree of weight loss was shown as conversion, , as follows:where , , and are initial mass of sample, mass at any time, and final mass at the end of reaction, respectively. The kinetic equation of reactivity is generally described aswhere is the reaction function and the reaction rate constant, , is a temperature function defined by Arrhenius equation aswhere is the exponential factor, is the apparent activation energy, and is the molar gas constant, 8.314 J/mol·K. Combining (2) and (3) and rearranging with heating rate , nonisothermal kinetics can be written asIntegrated function of (4) is represented asWith the FWO [26] method using Doyle’s approximation for the temperature integral, the following equation can be obtained:At a fixed value of , was plotted against at different heating rates. A straight line should be obtained with slope equal to . The activation energy can be calculated. The KAS [26] is based on the Coats-Redfern approximation of the temperature integral; the equation isDetermination of the activation energy is similar to the previous technique; by plotting against , a straight line should be obtained with a slope of and the activation energy can be calculated.

3. Results and Discussion

3.1. Thermal Degradation Characteristics

In this work, features of the thermal degradation characteristics were shown as the change of mass loss with temperature (TG) and mass loss rate (DTG) profiles. Nonisothermal thermogravimetric analysis of corncob was carried out at different heating rates of 10, 30, and 50 K/min in an oxygen atmosphere and the results are plotted in Figure 1. Thermogravimetric tests of corn stover were performed under similar conditions and the data plotted in Figure 2. It can be observed that the TG curves of both samples were similar, implying that the same reactions occurred at all heating rates. However, the temperatures corresponding to reactions were different and were shifted to a higher value with the higher heating rate. According to both TG results, increasing in temperature from ambient temperature to 900°C resulted in continuous weight loss and became constant at around 6–8% weight. The final product was ash. The differential TG curves gave three clear thermal degradation steps. This result was in agreement with previous researchers [19]. The first step of mass loss occurred in the temperature up to around 150°C corresponding to release of moisture content in the samples. Afterward, there was a small change in weight and then rapid weight loss occurred again in the second stage from approximately 200°C to around 400°C, which was attributed to the evolution of the volatile compounds generated during decomposition of cellulose and hemicelluloses. The final stage occurred, corresponding to the combustion of the remaining lignin and char residue from the previous reactivity.

(a)

(b)

(a)

(b)

The temperature values at each stage and those characteristics in which the reactions took place are presented in Table 2. The second and third stages showed major weight loss, about 55 and 30% of the total weight loss. The start and final temperatures of the devolatilization zone of corncob were in the range of 190–340, 194–372, and 204–378°C. The peak temperatures were 271, 289, and 295°C for heating rates of 10, 30, and 50 K/min, respectively. The corn stover devolatilization temperature was in the ranges 167–368, 177–390, and 177–391°C with the peak temperature of 275, 313, and 315°C at the same condition. The values obtained for the peak temperature during the devolatilization step of the thermal degradation were in similar magnitude to those obtained by Mansaray and Ghaly [19] for rice husk at a heating rate of 20 K/min. Moliner et al. [27] also obtained peak temperatures of 271, 273, 288, 292, and 297°C at heating rates of 2, 5, 10, 15, and 20 K/min, respectively.

It can be seen that the peak devolatilization temperature of stover was higher than cob but the mass loss rate was smaller. The thermal degradation characteristic was affected by the chemical composition of biomass. Difference in their constituent components resulted in different thermal behavior. According to the biochemical composition, both kinds of feedstock samples contained small lignin content, but the fractions of cellulose and hemicelluloses were relatively distinct. This indicated that different behaviors were expected in the devolatilization process. The thermal decomposition of the individual components of lignocellulosic materials was studied by several researchers [28–30] under different atmospheres. These results indicated that decomposition of hemicellulose starts first, followed by the cellulose and lignin. The lower peak temperature of cob can be explained by its higher hemicelluloses and lower cellulose content, compared with stover. Lignin decomposes within a wider range of temperatures and is considered to be the significant contributor for the production of char residue. There is similar lignin content in the two kinds of feedstock; therefore, the same amount of char residue was realized.

The degradation rate of the char combustion process in the third stage was lower than the devolatilization of the second step. The degradation rates of cob and stover were similar. Degradation of stover appeared to have a higher starting temperature and ends at a higher final temperature than cob. At a relatively high heating rate, the combustion of these char occurred within a much wider temperature range. A constant combustion rate was also observed. This observation generally agreed with the results reported by other researchers [16].

The decomposition process was shifted to a higher temperature zone as the heating rate increased. The peak degradation temperature during the first weight loss stage of cob and stover was increased from 74 and 69 to 98 and 101°C, respectively. For the second mass loss stage, it was increased from 271 and 275 to 295 and 315°C, respectively. The translation of the TG curves to higher temperature at higher heating rates was due to the reduction of residence time which was not sufficient for heat transfer to permeate into the center of the particle. Thus, the thermal decomposition process was delayed. To have the same weight loss, the degradation temperature was expected to be higher. Gai et al. [8] reported that this may have been due to the fact that, with the increase of heating rate, the time taken to reach the settled final temperature was less. Consequently, the heat transfer from the heating furnace within the thermogravimetric instrument to the tested sample may be limited, which may bring about a discrepancy between the recorded temperature and the actual sample temperature, agreed to by other researchers [16, 17, 31].

3.2. Kinetic Analysis

From TG analysis data, the kinetic parameters of overall weight loss were derived from the FWO and KAS methods. Figure 3 shows the evolution of mass loss as a function of temperature. Conversions of 0–15 and 85–100% were normally associated with the moisture release and the mineral matter decomposition. The conversion ranging between 20 and 80% was related to the volatile release and char combustion. Therefore, this conversion range was considered for the subsequent calculation, according to (6) and (7). Linear regression was plotted and shown in Figures 4 and 5. The apparent activation energy () can be calculated from the slopes, shown in Figure 6. Within the range of conversions considered, the values of activation energy obtained from both methods were similar. The FWO method appeared to give slightly higher than those from the KAS method. This was due to the distinctive linear approximation to the temperature integral. It was observed that the apparent activation energy of both samples varied with conversion fractions, showing similar trends. They showed an initial ascending trend in the range of 30–60% conversion and decreasing trend thereafter. The activation energies of corncob were around 77–249 and 69–252 kJ/mol with average value of 172 and 171 kJ/mol for the FWO and KAS methods, respectively. For corn stover, it was found to be around 47–237 and 37–241 kJ/mol with average value of 149 and 146 kJ/mol for the FWO and KAS methods. This means that the reaction mechanism varied considerably in an oxidative decomposition process. The activation energy was strongly dependent on conversion.

(a)

(b)

(a)

(b)

(a)

(b)

The characteristic of devolatilization occurred in conversions of around 20–60%. The average values of cob and stover in this step were 186 and 178 kJ/mol. Cellulose and hemicelluloses were decomposed in this range. Huang et al. [32] suggested that the apparent activation energy of cellulose was the highest, followed by hemicelluloses and lignin, respectively. The increase in activation energy at higher conversion may be attributed to ignition and oxidation of char residues. After 60% conversion range, char combustion took place. The average values in this step were 139 and 82 kJ/mol for cob and stover, respectively. The lower kinetic values of obtained in the oxidation zone, compared to those obtained in the devolatilization reaction zone, may be due to the fact that lignin which had lower decomposition rate than cellulose and hemicelluloses components was condensed to char [19]. There may also have been a catalytic effect from inorganic elements of ash on the combustion of char [33]. Mansaray and Ghaly [19] and Harun et al. [20] also reported lower in this zone for rice husk and bagasse, while the for combustion of sawdust was higher than those from the devolatilization. Leroy et al. [34] suggested that for conversions between 10 and 30% characterized processes involve competing reactions such as dehydration and pyrolysis. Between 30 and 60%, pyrolysis and smoldering combustion were in competition. For 60–90%, it was the transition of process to diffusion regime.

4. Conclusions

Thermal degradation of corncob and stover under a highly oxidative environment was investigated using TGA at different heating rates of 10, 30, and 50 K/min. Kinetic parameter in terms of the apparent activation energy was determined and compared using the FWO and KAS methods. Oxidative thermal degradation of both samples was found to occur in three mass loss stages: water evaporation, devolatilization, and char combustion. Increasing heating rate was observed to result in increasing mass loss rates, but the start of the thermal decomposition was delayed to higher temperatures. Different lignocellulosic composition of the feedstock may affect degradation behavior differently. Stover appeared to have higher hemicellulose and lower cellulose contents than cob and, hence, lower initial degradation temperatures. From the FWO and KAS methods, the activation energy was found to vary with the conversion fraction. The activation energy calculated by the FWO and KAS methods was similar. The average was about 172 and 149 kJ/mol for cob and stover, respectively.

Nomenclature

	Preexponential factor (s⁻¹)
	Apparent activation energy (kJ/mol)
	Reaction function
	Integral function of conversion
	Reaction rate constant (s⁻¹)
	Universal gas constant (8.314 × 10⁻³ kJ/mol·K)
	Temperature (K)
	Initial temperature (K)
	Initial mass of sample (kg)
	Mass at any time (kg)
	Final mass at the end of reaction (kg)
	Degree of conversion (—)
	Heating rate (K/min).

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors wish to acknowledge the supports from Thailand Research Fund (RSA5680011), the Energy Policy and Planning Office, Ministry of Energy, and Chiang Mai University.

References

S. Sokhansanj, A. Turhollow, J. Cushman, and J. Cundiff, “Engineering aspects of collecting corn stover for bioenergy,” Biomass and Bioenergy, vol. 23, no. 5, pp. 347–355, 2002.
View at: Publisher Site | Google Scholar
ASEAN Food Security Information System, Data Select on Maize based on calendar year, November 2014, http://www.afsisnc.org/statistics/data-selected?view=result&tbl_type=7.3&tbl_id=Maize&cty_id=Thailand.
K. Kanokkanjana and S. Garivait, “Climate change effect from black carbon emission: open burning of corn residues in Thailand,” World Acadamy of Science, Engineering and Technology, vol. 5, no. 10, pp. 177–180, 2011.
View at: Google Scholar
S. Moazzem, M. G. Rasul, and M. M. K. Khan, “A review on technologies for reducing CO₂ emission from coal fired power plants,” in Thermal Power Plants, M. Rasul, Ed., chapter 11, InTech, 2012.
View at: Publisher Site | Google Scholar
C. Lupiáñez, I. Guedea, I. Bolea, L. I. Díez, and L. M. Romeo, “Experimental study of SO₂ and NO_x emissions in fluidized bed oxy-fuel combustion,” Fuel Processing Technology, vol. 106, pp. 587–594, 2013.
View at: Publisher Site | Google Scholar
A. Kumar, L. Wang, Y. A. Dzenis, D. D. Jones, and M. A. Hanna, “Thermogravimetric characterization of corn stover as gasification and pyrolysis feedstock,” Biomass and Bioenergy, vol. 32, no. 5, pp. 460–467, 2008.
View at: Publisher Site | Google Scholar
M. V. Kok and E. Özgür, “Thermal analysis and kinetics of biomass samples,” Fuel Processing Technology, vol. 106, pp. 739–743, 2013.
View at: Publisher Site | Google Scholar
C. Gai, Y. Dong, and T. Zhang, “The kinetic analysis of the pyrolysis of agricultural residue under non-isothermal conditions,” Bioresource Technology, vol. 127, pp. 298–305, 2013.
View at: Publisher Site | Google Scholar
O. Senneca, “Kinetics of pyrolysis, combustion and gasification of three biomass fuels,” Fuel Processing Technology, vol. 88, no. 1, pp. 87–97, 2007.
View at: Publisher Site | Google Scholar
P. Parthasarathy, K. S. Narayanan, and L. Arockiam, “Study on kinetic parameters of different biomass samples using thermo-gravimetric analysis,” Biomass and Bioenergy, vol. 58, pp. 58–66, 2013.
View at: Publisher Site | Google Scholar
K. Slopiecka, P. Bartocci, and F. Fantozzi, “Thermogravimetric analysis and kinetic study of poplar wood pyrolysis,” Applied Energy, vol. 97, pp. 491–497, 2012.
View at: Publisher Site | Google Scholar
P. Luangkiattikhun, C. Tangsathitkulchai, and M. Tangsathitkulchai, “Non-isothermal thermogravimetric analysis of oil-palm solid wastes,” Bioresource Technology, vol. 99, no. 5, pp. 986–997, 2008.
View at: Publisher Site | Google Scholar
T. Wongsiriamnuay and N. Tippayawong, “Non-isothermal pyrolysis characteristics of giant sensitive plants using thermogravimetric analysis,” Bioresource Technology, vol. 101, no. 14, pp. 5638–5644, 2010.
View at: Publisher Site | Google Scholar
G. Mishra and T. Bhaskar, “Nonisothermal model free kinetics for pyrolysis of rice straw,” Bioresource Technology, vol. 169, pp. 614–621, 2014.
View at: Google Scholar
M. Jeguirim, S. Dorge, and G. Trouvé, “Thermogravimetric analysis and emission characteristics of two energy crops in air atmosphere: Arundo donax and Miscanthus giganthus,” Bioresource Technology, vol. 101, no. 2, pp. 788–793, 2010.
View at: Publisher Site | Google Scholar
D. K. Shen, S. Gu, K. H. Luo, A. V. Bridgwater, and M. X. Fang, “Kinetic study on thermal decomposition of woods in oxidative environment,” Fuel, vol. 88, no. 6, pp. 1024–1030, 2009.
View at: Publisher Site | Google Scholar
T. Wongsiriamnuay and N. Tippayawong, “Thermogravimetric analysis of giant sensitive plants under air atmosphere,” Bioresource Technology, vol. 101, no. 23, pp. 9314–9320, 2010.
View at: Publisher Site | Google Scholar
M. J. Safi, I. M. Mishra, and B. Prasad, “Global degradation kinetics of pine needles in air,” Thermochimica Acta, vol. 412, no. 1-2, pp. 155–162, 2004.
View at: Publisher Site | Google Scholar
K. G. Mansaray and A. E. Ghaly, “Determination of kinetic parameters of rice husks in oxygen using thermogravimetric analysis,” Biomass and Bioenergy, vol. 17, no. 1, pp. 19–31, 1999.
View at: Publisher Site | Google Scholar
N. Y. Harun, M. T. Afzal, and N. Shamsudin, “Reactivity studies of sludge and biomass combustion,” International Journal of Engineering, vol. 3, no. 5, pp. 413–425, 2009.
View at: Google Scholar
R. López, C. Fernández, J. Fierro, J. Cara, O. Martínez, and M. Sánchez, “Oxy-combustion of corn, sunflower, rape and microalgae bioresidues and their blends from the perspective of thermogravimetric analysis,” Energy, vol. 74, pp. 845–854, 2014.
View at: Publisher Site | Google Scholar
A. O. Aboyade, T. J. Hugo, M. Carrier et al., “Non-isothermal kinetic analysis of the devolatilization of corn cobs and sugar cane bagasse in an inert atmosphere,” Thermochimica Acta, vol. 517, no. 1-2, pp. 81–89, 2011.
View at: Publisher Site | Google Scholar
T. Sonobe, N. Worasuwannarak, and S. Pipatmanomai, “Synergies in co-pyrolysis of Thai lignite and corncob,” Fuel Processing Technology, vol. 89, no. 12, pp. 1371–1378, 2008.
View at: Publisher Site | Google Scholar
C. A. Mullen, A. A. Boateng, N. M. Goldberg, I. M. Lima, D. A. Laird, and K. B. Hicks, “Bio-oil and bio-char production from corn cobs and stover by fast pyrolysis,” Biomass and Bioenergy, vol. 34, no. 1, pp. 67–74, 2010.
View at: Publisher Site | Google Scholar
A. Demirbaş, “Calculation of higher heating values of biomass fuels,” Fuel, vol. 76, no. 5, pp. 431–434, 1997.
View at: Publisher Site | Google Scholar
J. E. White, W. J. Catallo, and B. L. Legendre, “Biomass pyrolysis kinetics: a comparative critical review with relevant agricultural residue case studies,” Journal of Analytical and Applied Pyrolysis, vol. 91, no. 1, pp. 1–33, 2011.
View at: Publisher Site | Google Scholar
C. Moliner, B. Bosio, E. Arato, and A. R. Greus, “Comparative study for the energy valorisation of rice straw,” Chemical Engineering Transactions, vol. 37, pp. 241–246, 2014.
View at: Publisher Site | Google Scholar
J. J. M. Orfão, F. J. A. Antunes, and J. L. Figueiredo, “Pyrolysis kinetics of lignocellulosic materials—three independent reactions model,” Fuel, vol. 78, no. 3, pp. 349–358, 1999.
View at: Publisher Site | Google Scholar
A. Chouchene, M. Jeguirim, B. Khiari, F. Zagrouba, and G. Trouvé, “Thermal degradation of olive solid waste: influence of particle size and oxygen concentration,” Resources, Conservation and Recycling, vol. 54, no. 5, pp. 271–277, 2010.
View at: Publisher Site | Google Scholar
M. G. Grønli, G. Várhegyi, and C. Di Blasi, “Thermogravimetric analysis and devolatilization kinetics of wood,” Industrial and Engineering Chemistry Research, vol. 41, no. 17, pp. 4201–4208, 2002.
View at: Publisher Site | Google Scholar
H.-M. Xiao, X.-Q. Ma, and Z.-Y. Lai, “Isoconversional kinetic analysis of co-combustion of sewage sludge with straw and coal,” Applied Energy, vol. 86, no. 9, pp. 1741–1745, 2009.
View at: Publisher Site | Google Scholar
Y. F. Huang, W. H. Kuan, P. T. Chiueh, and S. L. Lo, “A sequential method to analyze the kinetics of biomass pyrolysis,” Bioresource Technology, vol. 102, no. 19, pp. 9241–9246, 2011.
View at: Publisher Site | Google Scholar
C. di Blasi, “Combustion and gasification rates of lignocellulosic chars,” Progress in Energy and Combustion Science, vol. 35, no. 2, pp. 121–140, 2009.
View at: Publisher Site | Google Scholar
V. Leroy, D. Cancellieri, E. Leoni, and J.-L. Rossi, “Kinetic study of forest fuels by TGA: model-free kinetic approach for the prediction of phenomena,” Thermochimica Acta, vol. 497, no. 1-2, pp. 1–6, 2010.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2015 Poramate Sittisun et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1908

Downloads

1070

Citations