Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2016, Article ID 2573920, 12 pages
http://dx.doi.org/10.1155/2016/2573920
Research Article

Morphology of Near- and Semispherical Melted Chips after the Grinding Processes Using Sol-Gel Abrasives Based on SEM-Imaging and Analysis

1Subject Group of Metrology and Quality, Department of Mechanical Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland
2Department of Mechanical Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland
3Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, Wincentego Pola 2, 35-959 Rzeszów, Poland

Received 31 January 2016; Accepted 12 May 2016

Academic Editor: Michael Aizenshtein

Copyright © 2016 W. Kapłonek et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Citations to this Article [8 citations]

The following is the list of published articles that have cited the current article.

  • Grzegorz M. Krolczyk, Mariusz Michalski, Szymon Wojciechowski, Radoslaw W. Maruda, and Piotr Nieslony, “Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication,” Journal of Materials Engineering and Performance, vol. 26, no. 1, pp. 431–438, 2016. View at Publisher · View at Google Scholar
  • Guosheng Su, Yanjin Guan, and Zhanqiang Liu, “Microstructure of spherical particles generated in high-speed machining of an alloy steel,” International Journal of Materials Research, 2017. View at Publisher · View at Google Scholar
  • Somnath Chattopadhyaya, Aniruddha Ghosh, Grzegorz M. Krolczyk, Mohammad Shariq, Ravi Kumar, Pedro Vilaca, Ratnesh Kumar, Madhulika Srivastava, and Rupam Triphathi, “Characterization of friction surfaced coatings of aisi 316 tool over high-speed-steel substrate,” Transactions of Famena, vol. 41, no. 2, pp. 61–76, 2017. View at Publisher · View at Google Scholar
  • Tsadok Tsach, Nir Finkelstein, and Osnat Israelsohn-Azulay, “Effect of Cutting with an Abrasive Saw on Swarf Composition,” Journal of Forensic Sciences, 2018. View at Publisher · View at Google Scholar
  • O. G. Kulik, and E. D. Illarionova, “Intensification of Technical Grinding Modes by Managing Physical Processes of Chip Formation,” Proceedings of the 4th International Conference on Industrial Engineering, pp. 1457–1465, 2018. View at Publisher · View at Google Scholar
  • Akash Awale, Ashish Srivastava, Meghanshu Vashista, and M Z Khan Yusufzai, “Surface integrity characterization of ground hardened H13 hot die steel using different lubrication environments,” Materials Research Express, vol. 6, no. 2, pp. 026508, 2018. View at Publisher · View at Google Scholar
  • Yan Yang, Witold Habrat, Wojciech Skóra, Jolanta B. Królczyk, and Stanisław Legutko, “Effect of Modification of Mono-crystalline Corundum Grinding Wheel on Cutting Forces in Grinding of Aluminum Alloy 7075,” Energy Transfer and Dissipation in Plasma Turbulence, pp. 276–286, 2019. View at Publisher · View at Google Scholar
  • Déborah de Oliveira, Milla Caroline Gomes, and Márcio Bacci da Silva, “Spheroidal chip in micromilling,” Wear, vol. 426-427, pp. 1672–1682, 2019. View at Publisher · View at Google Scholar