Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2016 (2016), Article ID 2573920, 12 pages
http://dx.doi.org/10.1155/2016/2573920
Research Article

Morphology of Near- and Semispherical Melted Chips after the Grinding Processes Using Sol-Gel Abrasives Based on SEM-Imaging and Analysis

1Subject Group of Metrology and Quality, Department of Mechanical Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland
2Department of Mechanical Engineering, Faculty of Mechanical Engineering, Koszalin University of Technology, Racławicka 15-17, 75-620 Koszalin, Poland
3Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, Wincentego Pola 2, 35-959 Rzeszów, Poland

Received 31 January 2016; Accepted 12 May 2016

Academic Editor: Michael Aizenshtein

Copyright © 2016 W. Kapłonek et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. U. A. Dabade and S. S. Joshi, “Analysis of chip formation mechanism in machining of Al/SiCp metal matrix composites,” Journal of Materials Processing Technology, vol. 209, no. 10, pp. 4704–4710, 2009. View at Publisher · View at Google Scholar · View at Scopus
  2. A. Ebrahimi and M. M. Moshksar, “Evaluation of machinability in turning of microalloyed and quenched-tempered steels: tool wear, statistical analysis, chip morphology,” Journal of Materials Processing Technology, vol. 209, no. 2, pp. 910–921, 2009. View at Publisher · View at Google Scholar · View at Scopus
  3. P. Twardowski, S. Legutko, G. M. Królczyk, and S. Hloch, “Investigation of wear and tool life of coated carbide and cubic boron nitride cutting tools in high speed milling,” Advances in Mechanical Engineering, vol. 7, no. 6, pp. 1–9, 2015. View at Publisher · View at Google Scholar · View at Scopus
  4. S. Zhang and Y. B. Guo, “An experimental and analytical analysis on chip morphology, phase transformation, oxidation, and their relationships in finish hard milling,” International Journal of Machine Tools and Manufacture, vol. 49, no. 11, pp. 805–813, 2009. View at Publisher · View at Google Scholar · View at Scopus
  5. F. B. de Oliveira, A. R. Rodrigues, R. T. Coelho, and A. F. de Souza, “Size effect and minimum chip thickness in micromilling,” International Journal of Machine Tools and Manufacture, vol. 89, pp. 39–54, 2015. View at Publisher · View at Google Scholar · View at Scopus
  6. R. Li, L. Riester, T. R. Watkins, P. J. Blau, and A. J. Shih, “Metallurgical analysis and nanoindentation characterization of Ti-6Al-4V workpiece and chips in high-throughput drilling,” Materials Science and Engineering A, vol. 472, no. 1-2, pp. 115–124, 2008. View at Publisher · View at Google Scholar · View at Scopus
  7. F. Ke, J. Ni, and D. A. Stephenson, “Continuous chip formation in drilling,” International Journal of Machine Tools and Manufacture, vol. 45, no. 15, pp. 1652–1658, 2005. View at Publisher · View at Google Scholar · View at Scopus
  8. D. Zhu, S. Yan, and B. Li, “Single-grit modeling and simulation of crack initiation and propagation in SiC grinding using maximum undeformed chip thickness,” Computational Materials Science, vol. 92, pp. 13–21, 2014. View at Publisher · View at Google Scholar · View at Scopus
  9. D. Setti, M. K. Sinha, S. Ghosh, and P. Venkateswara Rao, “Performance evaluation of Ti-6Al-4V grinding using chip formation and coefficient of friction under the influence of nanofluids,” International Journal of Machine Tools and Manufacture, vol. 88, pp. 237–248, 2015. View at Publisher · View at Google Scholar · View at Scopus
  10. P.-L. Tso, “An investigation of chip types in grinding,” Journal of Materials Processing Technology, vol. 53, no. 3-4, pp. 521–532, 1995. View at Publisher · View at Google Scholar · View at Scopus
  11. Y. C. Wong and E. D. Doyle, “Implications of high strain deformation in grinding,” Wear, vol. 233–235, pp. 395–401, 1999. View at Publisher · View at Google Scholar · View at Scopus
  12. S. Malkin, “Negative rake cutting to simulate chip formation in grinding,” CIRP Annals—Manufacturing Technology, vol. 28, no. 1, pp. 209–212, 1979. View at Google Scholar · View at Scopus
  13. E. D. Doyle and S. K. Dean, “An insight into grinding from materials viewpoint,” CIRP Annals—Manufacturing Technology, vol. 29, no. 2, pp. 571–575, 1980. View at Google Scholar
  14. H. Letner, “Modern perspective of grinding process,” Grinding and Finishing, no. 1, p. 36, 1995. View at Google Scholar
  15. D. J. Badger, “Grinding: a pictorial odyssey; An examination of the grinding process through the lens of an electron microscope,” Cutting Tool Engineering Magazine, vol. 61, no. 2, pp. 44–49, 2009. View at Google Scholar · View at Scopus
  16. J. Badger, “Grinding: a pictorial odyssey, part II,” Cutting Tool Engineering, vol. 61, no. 12, pp. 48–52, 2009. View at Google Scholar · View at Scopus
  17. L. Lu, T. N. Farris, and S. Chandrasekar, “Sliding microindentation wear particles: spheres in grinding swarf,” Tribology Series, vol. 21, pp. 257–263, 1992. View at Publisher · View at Google Scholar
  18. G. Su and Z. Liu, “Experimental analysis on spherical chips in high-speed machining of hardened AerMet100,” Materials Science Forum, vol. 723, pp. 67–71, 2012. View at Publisher · View at Google Scholar · View at Scopus
  19. W. Kapłonek and K. Nadolny, “Assessment of the grinding wheel active surface condition using SEM and image analysis techniques,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 35, no. 3, pp. 207–215, 2013. View at Publisher · View at Google Scholar · View at Scopus
  20. K. Nadolny and W. Kapłonek, “SEM-based morphological analysis of the new generation aion-based abrasive grains (Abral) with reference to Al2O3/SiC/cBN abrasives,” Acta Microscopica, vol. 24, no. 1, pp. 64–78, 2015. View at Google Scholar · View at Scopus