Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2016, Article ID 8089525, 5 pages
http://dx.doi.org/10.1155/2016/8089525
Research Article

Enhanced Thermal Performance and Impact Strength of UHMWPE/Recycled-PA6 Blends Synthesized via a Melting Extrusion Route

1School of Materials Science and Engineering, Qiqihar University, Qiqihar 161006, China
2Center of Super-Diamond and Advanced Films (COSDAF), Department of Physics and Materials Science, City University of Hong Kong, Hong Kong
3Department of Mechanical Engineering and Shenzhen Research Institute, Hong Kong Polytechnic University, Hung Hom, Kowloon 999077, Hong Kong

Received 11 January 2016; Accepted 10 April 2016

Academic Editor: Gianluca Cicala

Copyright © 2016 Xiuying Yang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. P. Smith and P. J. Lemstra, “Ultra-high-strength polyethylene filaments by solution spinning/drawing,” Journal of Materials Science, vol. 15, no. 2, pp. 505–514, 1980. View at Publisher · View at Google Scholar · View at Scopus
  2. D. M. Bigg, M. M. Epstein, R. J. Fiorentino, and E. G. Smith, “Continuous extrusion of high-modulus semicrystalline polymers,” Journal of Applied Polymer Science, vol. 26, no. 2, pp. 395–409, 1981. View at Publisher · View at Google Scholar · View at Scopus
  3. P. Campbell, S. Ma, B. Yeom, H. McKellop, T. P. Schmalzried, and H. C. Amstutz, “Isolation of predominantly submicron-sized UHMWPE wear particles from periprosthetic tissues,” Journal of Biomedical Materials Research, vol. 29, no. 1, pp. 127–131, 1995. View at Publisher · View at Google Scholar · View at Scopus
  4. H.-G. Willert, H. Bertram, and G. Hans Buchhorn, “Osteolysis in alloarthroplasty of the hip: the role of ultra-high molecular weight polyethylene wear particles,” Clinical Orthopaedics and Related Research, no. 258, pp. 95–107, 1990. View at Google Scholar · View at Scopus
  5. Y. Lei, J. L. Guo, and X. D. Peng, “Molding technology of ultra high molecular weight polyethylene pipe and its application in oil and gas storage and transportation,” Petroleum Engineering Construction, vol. 31, pp. 1–3, 2005. View at Google Scholar
  6. W. S. Chow, Z. A. M. Ishak, J. Karger-Kocsis, A. A. Apostolov, and U. S. Ishiaku, “Compatibilizing effect of maleated polypropylene on the mechanical properties and morphology of injection molded polyamide 6/polypropylene/organoclay nanocomposites,” Polymer, vol. 44, no. 24, pp. 7427–7440, 2003. View at Publisher · View at Google Scholar · View at Scopus
  7. J. Roeder, R. V. B. Oliveira, M. C. Gonçalves, V. Soldi, and A. T. N. Pires, “Polypropylene/polyamide-6 blends: influence of compatibilizing agent on interface domains,” Polymer Testing, vol. 21, no. 7, pp. 815–821, 2002. View at Publisher · View at Google Scholar · View at Scopus
  8. C. Damm, H. Münstedt, and A. Rösch, “The antimicrobial efficacy of polyamide 6/silver-nano- and microcomposites,” Materials Chemistry and Physics, vol. 108, no. 1, pp. 61–66, 2008. View at Publisher · View at Google Scholar · View at Scopus
  9. H.-G. Wang, L.-Q. Jian, B.-L. Pan, J.-Y. Zhang, and S.-R. Yang, “Mechanical and tribological behaviors of polyamide 66/ultra high molecular weight polyethylene blends,” Polymer Engineering and Science, vol. 47, no. 5, pp. 738–744, 2007. View at Publisher · View at Google Scholar · View at Scopus
  10. Z. H. Yao, Z. H. Yin, G. E. Sun et al., “Morphology, thermal behavior, and mechanical properties of PA6/UHMWPE blends with HDPE-g-MAH as a compatibilizing agent,” Journal of Applied Polymer Science, vol. 75, no. 2, pp. 232–238, 2000. View at Publisher · View at Google Scholar · View at Scopus
  11. Z. Denchev and N. Dencheva, “Manufacturing and properties of aramid reinforced composites,” in Synthetic Polymer-Polymer Composites, chapter 8, pp. 251–280, Carl Hanser Verlag GmbH & Co, 2012. View at Google Scholar
  12. Y. Gong and G. Yang, “Single polymer composites by partially melting recycled polyamide 6 fibers: preparation and characterization,” Journal of Applied Polymer Science, vol. 118, no. 6, pp. 3357–3363, 2010. View at Publisher · View at Google Scholar · View at Scopus
  13. I. Kotter and W. Grellmann, Polymer Solids and Polymer Melts-Mechanical and Thermomechanical Properties of Polymers, vol. 6A3 of Landolt-Börnstein—Group VIII Advanced Materials and Technologies, Springer, 2014.
  14. D. Ghidoni, E. Bencini, and R. Nocci, “Compatibilizing PPE and PA6 with nitro-phthalimide derivatives,” Journal of Materials Science, vol. 31, no. 1, pp. 95–101, 1996. View at Publisher · View at Google Scholar · View at Scopus
  15. S. C. Tjong, S. A. Xu, and Y. W. Mai, “Impact fracture toughness of short glass fiber-reinforced polyamide 6,6 hybrid composites containing elastomer particles using essential work of fracture concept,” Materials Science and Engineering A, vol. 347, no. 1-2, pp. 338–345, 2003. View at Publisher · View at Google Scholar · View at Scopus
  16. M. Pracella, L. Rolla, D. Chionna, and A. Galeski, “Compatibilization and properties of poly(ethylene terephthalate)/polyethylene blends based on recycled materials,” Macromolecular Chemistry and Physics, vol. 203, no. 10-11, pp. 1473–1485, 2002. View at Publisher · View at Google Scholar · View at Scopus
  17. O. De Giacomo, A. Cesàro, and L. Quaroni, “Synchrotron based FTIR spectromicroscopy of biopolymer blends undergoing phase separation,” Food Biophysics, vol. 3, no. 1, pp. 77–86, 2008. View at Publisher · View at Google Scholar · View at Scopus