Table of Contents Author Guidelines Submit a Manuscript
Advances in Materials Science and Engineering
Volume 2018, Article ID 4572989, 11 pages
https://doi.org/10.1155/2018/4572989
Research Article

Mode-I Metal-Composite Interface Fracture Testing for Fibre Metal Laminates

Aerospace Engineering Cluster, School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore

Correspondence should be addressed to Gin Boay Chai; gs.ude.utn@iahcbgm

Received 15 October 2017; Accepted 20 December 2017; Published 28 February 2018

Academic Editor: Fabrizio Sarasini

Copyright © 2018 Periyasamy Manikandan and Gin Boay Chai. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. A. Vlot and J. W. Gunnink, Fibre Metal Laminates: An Introduction, Kluwer Academic Publishers, Norwell, USA, 2001.
  2. G. B. Chai and P. Manikandan, “Low velocity impact response of fibre-metal laminates—A review,” Composite Structures, vol. 107, pp. 363–381, 2014. View at Publisher · View at Google Scholar · View at Scopus
  3. M. Sadighi, R. C. Alderliesten, and R. Benedictus, “Impact resistance of fiber-metal laminates: a review,” International Journal of Impact Engineering, vol. 49, pp. 77–90, 2012. View at Publisher · View at Google Scholar · View at Scopus
  4. T. Sinmazçelik, E. Avcu, M. Ö. Bora, and O. Çoban, “A review: fibre metal laminates, background, bonding types and applied test methods,” Materials & Design, vol. 32, no. 7, pp. 3671–3685, 2011. View at Publisher · View at Google Scholar · View at Scopus
  5. L. J. Hart Smith, “Adhesive joints for composites-phenomenological considerations,” in Proceedings of Conference on Composite Technology, EI Segundo, CA, USA, September 1978.
  6. A. Vlot and J. W. Van Ingen, “Delamination resistance of post-stretched fibre metal laminates,” Journal of Composite Materials, vol. 32, no. 19, pp. 1784–1805, 1998. View at Publisher · View at Google Scholar · View at Scopus
  7. B. A. Huppe, High Reliability Adhesive Joining of Metal and Composite Components, Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA, USA, 2001.
  8. J. R. Reeder, K. Demarco, and K. S. Whitley, “The use of doubler reinforcement in delamination toughness testing,” Composites Part A: Applied Science and Manufacturing, vol. 35, no. 11, pp. 1337–1344, 2004. View at Publisher · View at Google Scholar · View at Scopus
  9. M. D. Thouless, J. L. Adams, M. S. Kafkalidis, S. M. Ward, R. A. Dickie, and G. L. Westerbeek, “Determining the toughness of plastically deforming joints,” Journal of Materials Science, vol. 33, no. 1, pp. 189–197, 1998. View at Publisher · View at Google Scholar
  10. G. Lawcock, L. Ye, Y. W. Mai, and C. T. Sun, “The effect of adhesive bonding between aluminum and composite prepreg on the mechanical properties of carbon-fiber-reinforced metal laminates,” Composites Science and Technology, vol. 57, no. 1, pp. 35–45, 1997. View at Publisher · View at Google Scholar · View at Scopus
  11. G. V. Reyes and W. J. Cantwell, “The mechanical properties of fiber-metal laminates glass fibre reinforced polypropylene,” Composites Science and Technology, vol. 60, no. 7, pp. 1085–1094, 2000. View at Publisher · View at Google Scholar · View at Scopus
  12. S. Mostovoy, E. J. Ripling, and C. F. Bersch, “Fracture toughness of adhesive joints,” Journal of Adhesion, vol. 3, no. 2, pp. 125–144, 1971. View at Publisher · View at Google Scholar · View at Scopus
  13. K. Song, K. C. G. Dávila, and C. A. Rose, “Guidelines and parameter selection for the simulation of progressive delamination,” in Proceedings of Abaqus User Conference, Newport, RI, USA, May 2008.
  14. A. Turon, C. G. Dávila, P. P. Camanho, and J. Costa, “An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models,” Engineering Fracture Mechanics, vol. 74, no. 10, pp. 1665–1682, 2007. View at Publisher · View at Google Scholar · View at Scopus
  15. B. R. K Blackman, J. P. Dear, A. J. Kinloch, and S. Osiyemi, “The calculation of adhesive fracture energies from double-cantilever beam test specimens,” Journal of Materials Science Letters, vol. 10, no. 5, pp. 253–256, 1991. View at Publisher · View at Google Scholar · View at Scopus
  16. B. R. K Blackman, A. J. Kinloch, F. S. Rodriguez-Sanchez, and W. S. Teo, “The fracture behaviour of adhesively-bonded composite joints: effects of rate of test and mode of loading,” International Journal of Solids and Structures, vol. 49, no. 13, pp. 1434–1452, 2012. View at Publisher · View at Google Scholar · View at Scopus
  17. P. Manikandan and G. B. Chai, “A layer-wise behavioral study of metal based interply hybrid composites under low velocity impact load,” Composite Structures, vol. 117, pp. 17–31, 2014. View at Publisher · View at Google Scholar · View at Scopus
  18. A. Hillerborg, M. Modéer, and P. E. Petersson, “Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements,” Cement and Concrete Research, vol. 6, no. 6, pp. 773–781, 1976. View at Publisher · View at Google Scholar · View at Scopus