Analysis of Titania Nanosheet Adsorption Behavior Using a Quartz Crystal Microbalance Sensor

Tashiro, Yuichiro; Komasa, Satoshi; Miyake, Akiko; Nishizaki, Hiroshi; Okazaki, Joji

doi:https://doi.org/10.1155/2018/7461245

Advances in Materials Science and Engineering

On this page

Abstract Introduction Materials and Methods Results Discussion Conclusions Conflicts of Interest Authors’ Contributions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 7461245 | https://doi.org/10.1155/2018/7461245

Analysis of Titania Nanosheet Adsorption Behavior Using a Quartz Crystal Microbalance Sensor

Yuichiro Tashiro,¹Satoshi Komasa,¹Akiko Miyake,²Hiroshi Nishizaki,¹and Joji Okazaki¹

Academic Editor: Marco Cannas

Received17 Aug 2017

Accepted29 Nov 2017

Published19 Feb 2018

Abstract

We investigated the adsorption of albumin and fibronectin on a titania nanosheet- (TNS-) modified quartz crystal microbalance (QCM) sensor. A Ti QCM sensor was fabricated by reactive magnetron sputtering. A thin layer of Ti was deposited on the QCM sensor. This sensor was then alkali-modified by treatment with NaOH at room temperature to fabricate the titania nanosheets. Scanning probe microscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy were performed to investigate the surface topology and chemical components of each sensor. The TNS had a titanium oxide film exhibiting a nodular structure and a thickness of 13 nm on the QCM sensor. Furthermore, QCM measurements showed significantly greater amounts of albumin and fibronectin adsorbed on the TNS than on titanium. The NaOH treatment of titanium modified the sensor surface and improved the adsorption behaviors of proteins related to the initial adhesion of bone marrow cells. Therefore, we concluded that TNS improves the initial adhesion between the implant materials and the surrounding tissues.

1. Introduction

Titanium is a biocompatible material that is commonly used in dentistry and orthopedic reconstruction. The surface features of implant materials have important functions in cell or extracellular matrix interrelationships and eventual osseointegration. Therefore, interrelationships between cells and microtopography have been intensively studied.

An important contemporary advance in dental implant research is the ability to modify implant surface materials at the nanoscale [1, 2]. Materials with an expanded surface region and a better surface roughness may yield better mechanical interlocking between tissues and titanium [3]. However, more importantly, such nanoscale features are also believed to directly affect osteogenic cell behaviors around implant fixtures with nonconventional surfaces, creating a biomimetic relationship between alloplastic surfaces and host tissues by the replication of the natural cellular environment at the nanometer level [1, 2, 4].

Low-dimensional TiO₂ nanostructures have attracted recent attention because these materials can take the forms of nanotubes [5], nanofibers [6], and nanowires [7]. Compared with mass materials or nanoparticles, TiO₂ nanotubes have high particular surface zones accessible for the adsorption of color sensitizers, and they provide channels to improve electron exchange, thus expanding the effectiveness of solar cells [5]. Titania nanosheets (TNSs) are similar to TiO₂ nanotubes, created by titania deposition using the sputtering process [5].

In our previous study [8], we showed that TNSs created by compound processing enhance the osteogenic separation of rodent bone marrow (RBM) cells. The surface properties and structural characteristics of materials play an important role in protein and cell adsorption behaviors. The initial amount adsorbed and the conformation of proteins contained in the serum could alter the bioactivity of stem cells on TNSs. However, the bioactivities of TNS materials, including their roles in osteogenic differentiation and the biointegration of dental implants into the alveolar bone, have not been elucidated.

A quartz crystal microbalance (QCM) sensor is a profoundly delicate and handy device that is used to observe protein adsorption and cell behavior in situ. A QCM-based sensor comprises a quartz crystal and a detection material. A 27 MHz QCM can provide highly sensitive measurements of mass in aqueous solutions; the resonance frequency decreases in relation to the mass of the protein bound on the QCM electrode surface. We previously fabricated several types of QCM sensors by coating the gold electrode of the quartz crystal with a thin film of a biomaterial [9]; this QCM sensor achieved an increase in sensitivity approximately 24 times that of a conventional 5 MHz QCM. PMMA (poly(methyl methacrylate)), Au, and Ti have been used as QCM electrode surface materials to imitate denture materials and evaluate the adsorption behaviors of various bovine salivary proteins [10]. These previous findings support the potential utility of the QCM method for the evaluation of protein adsorption behaviors on implant surfaces.

In this study, we evaluated the effects of modified surfaces on the adsorption of albumin and fibronectin in RBM cells and simulated body fluid (SBF) in QCM analyses.

2. Materials and Methods

2.1. Sputtering Procedure

A thin layer of Ti was deposited on quartz discs (diameter: 8 mm, area: 4.9 mm²) by reactive magnetron sputtering using a radio-frequency magnetron sputtering system (CFS-4ES-231; Shibaura Mechatronics Co., Ltd., Kanagawa, Japan). The QCM crystal was cleaned using piranha solution (H₂SO₄/30% H₂O₂ (v/v): 7 : 3). Before deposition was conducted, the quartz surfaces were ultrasonically cleaned in high-purity acetone (99.999%). Pure Ti powder was used to prepare the target, which was formed by pressing the powder into a disc with a diameter of 75 mm. The quartz substrates were positioned 85 mm above the target, and the magnetron sputtering chamber was evacuated to a pressure of 3 × 10⁻³ Pa. Argon was used as the working gas, and its pressure was kept constant at 6.7 × 10⁻¹ Pa. All of the films were fabricated using a constant radio-frequency discharge power of 480 W, and the Ti thin films were deposited at room temperature at a deposition rate of 20.0 nm/min, yielding a film thickness of approximately 240 nm. The crystals were washed and cleaned with both sodium dodecyl sulfate and UV-Ozone Cleaner (PC450; Meiwafosis Co., Ltd., Osaka, Japan) prior to QCM measurements.

2.2. Sample Preparation

In the TNS group, Ti sensors were treated to produce TNS on their surfaces. An unprocessed QCM sensor was used as the Ti sensor. These sensors were immersed in 10 M NaOH (aq) and were then placed in an oil bath, which was kept at a temperature of 30°C for 24 h. The solution in each flask was replaced and treated with distilled water (200 mL), and this procedure was repeated until the point that a conductivity of 5 μS/cm³ was reached. The specimens were then dried at room temperature.

2.3. Characterization of Materials

Scanning electron microscopy (S-4800; Shimadzu, Kyoto, Japan) and scanning probe microscopy (SPM-9600; Shimadzu) over a surface area of 2.0 μm × 2.0 μm were conducted to observe the surface topology and roughness of the fabricated TNS and Ti sensors. The composition of the coating was analyzed by X-ray photoelectron spectroscopy (XPS; ESCA 5600, Ulvac-Phi Inc., Kanagawa, Japan) using surface etching with ionized argon. In addition, the surfaces of the fabricated Ti sensors were subjected to XPS analysis with an Al Kα line (15 kV, 300 W) as an X-ray source. During XPS, argon ion sputtering was applied to determine the thickness and structure of the surface layers.

2.4. Contact Angle Measurements

Contact angles were measured for the TNS and Ti sensors using a video contact angle measurement system (model VSA 2500 XE; AST Products Inc., Billerica, MA, USA). A small droplet of a deionized water solution with Hanks’ Balanced Salt Solution and bovine serum albumin (BSA; approximately 3 mg) was placed on the TNS to measure the static contact angle. Estimation of the contact edge is a straightforward strategy for breaking down the vitality and hydrophilic nature of a surface.

2.5. Proteins

BSA (Wako Pure Chemical Industries Ltd., Osaka, Japan) was dissolved in phosphate-buffered saline (PBS; pH 7.4) at 200 μg/mL. Human plasma fibronectin (HFN; Nacalai Tesque, Inc., Kyoto, Japan) was dissolved in PBS (pH 7.4) at 500 μg/mL.

2.6. Cell Culture

Since most bone embed materials are embedded in adult bone that is in direct contact with bone marrow tissue, the effects and success of new embed materials can be investigated by examining bone marrow cell cultures from adult rats. RBM cells multiply and separate into a phenotype that expresses bone cell markers in vitro. RBM cells were extracted from the femurs of 7-week-old Sprague–Dawley rats. The rats were humanely sacrificed utilizing 4% isoflurane, and the bones were aseptically extracted from the hind limbs. The external soft tissues were discarded, and the extracted bone samples were immersed in 50 mL of Eagle’s minimal essential medium (EMEM; Wako) supplemented with 20% fetal bovine serum (lot number 1,412,447; Invitrogen, Life Technologies Corp., Carlsbad, CA, USA) and penicillin (850 U/mL) for approximately 15 min.

The proximal end of the femur and the distal end of the tibia were cut. An 18-gauge needle (TERMO, Japan) was introduced into the opening at the knee-joint end of each bone, and the marrow was washed out of the bone shaft by EMEM. The obtained marrow pellet was separated by trituration, and the cell suspensions obtained from all the bones were combined by centrifugation. RBM cells were cultured in 75 cm² culture flasks (TD75; Falcon) in EMEM. At confluence, the cells were removed by trypsinization, washed twice in EMEM, resuspended in culture medium, and seeded on test and control titanium disks at a concentration of 4 × 10⁴ cells/cm² in 24-well tissue culture plates. The cells were incubated for 3 days in a CO₂ incubator at 37°C. This investigation was conducted in accordance with the Guidelines for Animal Experimentation of Osaka Dental University (Approval no. 16-08001).

2.7. QCM Measurements

The amounts of proteins (BSA and HFN) and RBM cells were determined by QCM measurements (Affinix QN μ; Initium Co., Ltd., Tokyo, Japan). Affinix QN μ had a 550 µL cell outfitted with a 27 MHz QCM plate at the base of the cell. The diameter of the quartz plate was 8 mm, and the area of the gold-plated quartz was 4.9 mm². The unit also included a mixing bar and a temperature controller. The adjustment in recurrence was checked utilizing a universal frequency counter connected to a microcomputer.

The Ti QCM sensors and TNS were immersed in 500 μL of PBS (0.01 M PBS at pH 7.4). Changes in the QCM frequency were measured as a function of time; recording started immediately after the infusion of 5 μL (20 μg/mL) of BSA, HFN, and RBM cells. The solution was mixed to avoid any influence of protein dispersion on the measured results. Stirring did not influence the soundness of the frequency or the degree of frequency adjustment. The frequency change relied upon the adsorbed mass in accordance with the Sauerbrey equation:

As per this condition, at 27 MHz, a frequency shift of 1 Hz relates to a mass difference in roughly 0.62 ng·cm⁻². In the Sauerbrey equation, is the fundamental frequency of the quartz crystal (27 × 10⁶ Hz), is the measured frequency shift (Hz), is the density of quartz (2.65 g·cm⁻³), is the mass change (g), is the electrode area (0.049 cm²), and is the shear modulus of quartz (2.95 × 1011 dyn·cm⁻²). QCM observation was performed at 25°C, and the test was repeated four times. Results are depicted as mean ± standard deviation.

2.8. XPS Analysis after Measuring the Adsorption of BSA and HFN Using Ti and TNS QCM Sensors

The biochemical constituents of the adsorbed protein films on the QCM sensors were investigated by XPS on an AXIS Ultra DLD spectrometer (Kratos Instruments, Manchester, UK) equipped with a monochromated Al Kα X-ray source (hv = 1486.6 eV) operated at 75 W. XPS was utilized to investigate the proteinaceous carbon (C1s) and nitrogen (N1s) signals produced by the protein. Evaluation of the C1s and N1s signals emerging from the peptide bonds of the protein was conducted to determine the relative amount of protein adsorbed on various surfaces.

2.9. Preparation of SBF

Since SBF is supersaturated with respect to apatite, improper planning can prompt the precipitation of apatite in the solution. Therefore, the solution should remain colorless and transparent, and there should not be any deposition on the inner surface of the container. If precipitation is observed, the preparation of SBF should be halted, and the procedure should be restarted at the step of washing the apparatus.

For preparation of 1 L of SBF, 700 mL of ion-exchanged and distilled water was added to a 1 L plastic beaker with a stir bar. The beaker was covered with plastic wrap, and the water was heated to 36.5 ± 1.5°C under stirring. Reagents 1–8 were then dissolved into the solution in order (given in Table 1) at 36.5 ± 1.5°C, and reagents 9 (Tris) and 10 (HCl) were added after pH adjustment.

Note that during this procedure, instead of glass containers, plastic containers with smooth, unscratched surfaces were used because apatite nucleation can be induced on the surfaces of glass containers or the edges of scratches. Additionally, reagents were dissolved completely before addition of the next reagent. The volume of 1 M HCl was measured using a cylinder after the cylinder had been washed with 1 M HCl. Finally, hygroscopic reagents, such as KCl, K₂HPO₄·3H₂O, MgCl₂·6H₂O, CaCl₂, and Na₂SO₄, were measured as quickly as possible.

The temperature of the solution was set to 36.5 ± 1.5°C. If the amount of solution was less than 900 mL, ion-exchanged and distilled water was added to increase the volume to 900 mL. The pH of the solution was then determined. Before Tris was added to the solution and dissolved, the pH of the solution was 2.0 ± 1.0. The solution temperature was kept within the range of 35–38°C (optimal: 36.5 ± 0.5°C), and the added Tris was dissolved slowly, while changes in pH were noted. Tris was added until the pH reached approximately 7.45.

3. Results

3.1. Scanning Electron Microscopy (SEM) and SPM Analysis

SEM images are shown in Figure 1. After modification in NaOH at 30°C, the TNS sensor surfaces showed a nanoscale network structure. SPM was utilized to gauge the depth of the surface characteristics of the specimens, and the surface morphologies of the TNS and Ti sensors are shown in Figure 2. Many nanonodules were detected on the TNS surface; these formations had horizontal dimensions of approximately 300 nm. The surface roughness (Ra) values were 3.9 and 18.9 nm for the Ti and TNS sensors, respectively.

(a)

(b)

(a)

(b)

3.2. XPS Analysis

Figure 3 shows the results of wide-scan XPS surface chemical analyses of Ti and TNS QCM sensors. The presence of Ti, O, C, and N was confirmed on the surfaces of Ti and TNS QCM sensors. In addition, the presence of Na was confirmed on the surface of the TNS QCM sensor. Moreover, the Ti and O concentrations of TNS QCM sensors were higher than those on the surface of TNS QCM sensors.

(a)

(b)

3.3. Surface Wettability

The contact angle for a water drop on the Ti sensor was 42.5°. However, the water drops spread very rapidly as they reached the test sensor, and the contact angle could not be determined. However, the behavior on the TNS sensor indicated that the sensor was superhydrophilic (contact angle of less than 5°).

3.4. QCM Measurement of Proteins

Figure 4 shows the adsorption of albumin and fibronectin based on QCM measurements. An immediate decrease in frequency was observed after the injection of albumin and fibronectin. This decrease in frequency was identified with the adsorption of albumin and fibronectin. The adsorption of albumin and fibronectin on the TNS sensor produced a decrease in frequency that was greater than that measured for the Ti sensor. According to Sauerbrey’s equation, at 27 MHz, a frequency decrease of 1 Hz compares to a mass difference of around 0.62 ng/cm² [10]. After 30 min, the amounts of albumin adsorbed on the TNS and Ti sensors were 187.8 and 117.5 ng/cm², respectively, and the amounts of fibronectin adsorbed on the TNS and Ti sensors were 827.6 and 533.7 ng/cm², respectively.

(a)

(b)

3.5. QCM Measurement of RBM Cells

Figure 5 shows the adsorption of rat bone marrow cells based on QCM measurements. An immediate decrease in frequency was observed after the injection of RBM cells. The adsorption of RBM cells on the TNS sensor produced a decrease in frequency that was greater than that measured for the Ti sensor. Using Sauerbrey’s equation, after 30 min, the amounts of albumin adsorbed on the TNS and Ti sensors were 1491.1 and 872.5 ng/cm², respectively.

3.6. XPS Analysis after Adsorption of Proteins

The XPS spectra of the Ti and TNS QCM sensors after immersion in BSA are summarized in Figures 6 and 7, and those of the Ti and TNS QCM sensors after immersion in HFN are shown in Figures 8 and 9. For XPS analysis, the N1s and C1s spectra were measured. The coupling energies (BEs) of the C1s range for adsorbed BSA were 284.8 eV (C-C/C-H), 286.4 eV (C-O/C-N), and 288.2 eV (O=C-O) for the Ti QCM sensors and 284.8 eV (C-C/C-H), 286.4 eV (C-O/C-N), and 288.6 eV (O=C-O) for the TNS QCM sensors. There were N1s peaks for the Ti and TNS QCM sensors after the adsorption of BSA. The BEs of the C1s spectrum for adsorbed HFN were 284.8 eV (C-C/C-H), 286.4 eV (C-O/C-N), and 288.0 eV (O=C-O) in the Ti QCM sensors and 284.7 eV (C-C/C-H), 286.4 eV (C-O/C-N), and 288.0 eV (O=C-O) for the TNS QCM sensors. After adsorption of the HFN, there were also N1s center-level spectra for the Ti and TNS QCM sensors.

(a)

(b)

(a)

(b)

(a)

(b)

(a)

(b)

3.7. Characterization after Immersion in SBF

Figure 10 shows the adsorption of apatite after exposure to the SBF solution based on QCM measurements. A quick frequency reduction was seen after the infusion of SBF. The adsorption of SBF on the TNS sensor produced a decrease in the frequency that was greater than that measured for the Ti sensor.

Figure 11 shows the surface morphology of the Ti and TNS QCM sensors after immersion in SBF for 24 h. After immersion, a recently framed layer was seen on the Ti and TNS surfaces. The surface was covered by single and grouped ball-like particles with a size of around 1.5 μm. The number of particles on the surface of the TNS QCM sensor was clearly greater than that on the surface of the Ti QCM sensor.

(a)

(b)

4. Discussion

In this study, Ti sensors were realized by depositing a thin Ti film on a QCM electrode using a reactive DC magnetron sputtering technique; this sensor was further alkali modified using NaOH treatment to fabricate the TNS. SPM and XPS analyses were carried out to characterize the nanostructure of the TNSs. We evaluated the quality of the TNSs and the potential application of the high-frequency TNS sensors by investigating the in situ binding behaviors for TNS sensors, two proteins, RBM cells, and SBF to determine the effects of these parameters on biological reactions in solution.

Several studies have demonstrated that implant surfaces affect nanoscale topography and thereby alter cell behaviors or change the nanofeatures of structures to improve the osseointegration process [4, 11, 12]. The embed surface can be adjusted by various approaches to add nanoscale features to the surfaces in specific combinations. The most well-known techniques are chemical processes, such as alkaline hydrothermal [13, 14] or acid [15, 16] oxidation, on titanium surfaces to produce diverse nanoscale topographies. Kasuga et al. [5] demonstrated that TiO₂ nanotubes with a diameter of about 8 nm and a length of about 100 nm could be formed by Ti treatment with a 10 M NaOH aqueous solution for 20 h at 110°C, without the need for templates or replication. Essential factors in regulating cell reactions at the implant-tissue interface can dramatically affect tissue coordination [17]. In a recent work, we demonstrated that TiO₂ nanotubes and TNSs could be formed on titanium metal surfaces by treatment with a 10 M NaOH aqueous solution at 30°C, and we used this method to prepare TNS-modified disks. Komasa et al. [8] suggested that TNSs on titanium surfaces can be applied to control the osteogenic differentiation of bone marrow cells and enhance mineralization. Our results demonstrated that TNS-modified titanium disks were more hydrophilic and showed uniquely enhanced wettability in comparison with unmodified disks. Further studies of the surface roughness and topography of modified titanium alloy surfaces are needed to assess their wettability. Ra is a commonly used height parameter to describe implant surface roughness; Ra of the TNS-modified titanium surface was 19 nm, which was greater than that of the untreated titanium surface. The contact angles of the alkali-treated titanium disks gradually decreased in comparison with those of the control group, indicating that the wettability of the surface of the test group was reduced by NaOH treatment. In previous studies, a surface roughness of between 13 and 16 nm was found to be optimal for RBM cell culture [18, 19]. The nanonetwork structure framed on the titanium disks here was like the hierarchical structure outlined by Zhao et al. [12]. In their work, hierarchical nanotextured titanium surface topographies with TNS structures that mirrored the hierarchical structures of bone tissues were created by etching followed by anodization. Natural tissues are hierarchical structures of nanoscale building blocks organized in a structured way. Hierarchical structures composed of nanocomponents may give a more reasonable surface topography for bone marrow cell functions than simpler structures because they can better copy the structures of natural tissues. Our research revealed that NaOH treatment prompts the development of a Ti-O-Na titanate layer on the titanium surface. Thus, we expect that NaOH treatment results in the formation of a thick oxide film on the TiO₂ layer on the titanium surface. The deconvolution procedure suggested that this may have been due to surface contamination resulting from the binding of O to C [20].

Before argon ion etching was performed, the XPS depth profiles perpendicular to the surface of the sample showed a carbon contamination overlayer on the surface. This carbon contaminant was removed after the initial etching cycles. The oxygen and Ti concentrations gradually decreased and increased, respectively, as the number of etching cycles increased. Kim et al. [21] demonstrated that NaOH and heat treatment resulted in the covering of the Ti substrate with a titanium oxide layer with a thickness of approximately 1000 nm; AES depth profiles of the Ti oxide layer indicated the presence of an amorphous sodium titanate hydrogel layer. Kasuga et al. [5] likewise showed that NaOH treatment prompted the formation of a Ti-O-Na titanate layer on the Ti surface. At a greater depth of approximately 250 nm, the oxygen concentrations remained almost constant at 5 atom%. In addition, the remaining oxygen content was approximately 5 atom% inside the titanium film, which was attributed to the presence of residual oxygen in the chamber after preparation of the Ti sample.

All embed surfaces are promptly covered with a layer of protein from the in vitro culture medium or in vivo biological fluids, and this interface regulates the course of cell reactions and behaviors [22]. To elucidate the connection between the Ti implant surface properties, opsonization, and phagocytosis under in vivo conditions, phagocytic experiments were previously conducted using a cell culture medium supplemented with serum albumin and human opsonizing serum factors [23]. Fibronectin plays a crucial role in the progressive differentiation of osteoblasts [24]. Additionally, fibronectin has RGD sequences and is a large extracellular matrix dimer glycoprotein [25] with a molecular weight of approximately 440 kDa [26]. Albumin is the most abundant plasma protein; it suppresses the adsorption of other proteins that may empower aggravation and bacterial colonization [27]. The molecular weight of BSA is approximately 6-7 kDa [28]. In this study, the amount of fibronectin adsorbed was greater than the amount of albumin adsorbed, suggesting that adsorption quantity was related to the molecular weight of the injection solutions. After adsorption of BSA and BSF, N1s core-level spectra were obtained for both QCM sensors. Endo [29] detected C, O, and N obtained from the organic material or metal oxide on the titanium surface by XPS investigation. In the present study, based on XPS, the C1s and N1s peaks derived from BSA and BSF were detected on both QCM sensor surfaces tested. Evaluation of the N1s peak emerging from the peptide bonds of the implant-bone bonding protein may be a successful measure of the relative amount of protein adsorbed onto implant surfaces on the TNS QCM sensor.

Our results are the first comparison of RBM cell proliferation on TNS-modified titanium surfaces and unprocessed controls. Surfaces with nanostructures have higher surface areas than those of surfaces without such features [11, 30]. This expanded surface territory permits increased adhesion of cells, such as osteoblasts and fibroblasts. Thus, the altered surface energies of materials with nanostructures may promote tissue growth via increased adsorption of select proteins compared with materials with microscale features [31]. The adsorption of select proteins can in this manner guide the adhesion of cells on the implant material surface, among other capabilities. Various investigations have exhibited improved cell adhesion and multiplication on nanostructured surfaces, with various potential tissue applications, including applications in the bladder, bone, vasculature, and nervous system [32–34]. A prior study suggested that TNSs on titanium surfaces facilitate the regulation of osteoblastic differentiation of bone marrow cells and enhance mineralization. The current study showed that the TNSs formed nanonodules with a diameter of about 19 nm on the titanium surfaces, and these structures promoted the adhesion and/or multiplication of cells. The network structure of TNSs on titanium alloy facilitated rapid cell adhesion, spreading, and multiplication due to the mechanics of the TNS structure and chemical nature of the Ti-O-Na layer.

To enhance bone-titanium bonding, Kokubo et al. recently demonstrated that a blend of alkalis resulted in the formation of bone-like apatite on the surface of titanium in SBF with an ion concentration almost equivalent to that of human blood [35]. Apatite development on the material surface is accepted to be essential for bioactivity, that is, direct bone bonding. In our study, there was an apatite layer on the TNS QCM sensor after 24 h. Thus, the increased adhesion of RBM cells and SBF on the TNS QCM sensor suggested that TNS induced bone differentiation.

In the TNS sensor, the concentration of Ti exceeded that of oxygen at a depth of approximately 170 nm. Subsequently, the NaOH treatment was thought to produce a thick oxide film. Nonetheless, the chemical structure of the treated surfaces did not vary fundamentally; Ti oxides (mostly TiO₂) formed at the surface. Albumin and fibronectin were readily adsorbed, to a greater extent on the TNS sensor than on the reference Ti sensor. The TNS surface seemed to adsorb more protein for a given geometric surface area than the reference Ti sensor; this may have been a result of its rough morphology, as evidenced by the SEM and SPM results. Several studies [36, 37] have shown that nanostructured topographies can act as good mimics of natural extracellular matrixes. Advancement of the surface topography could be indirect; the adsorption of proteins or ions may function as an extension between the nanosurface structure and cells [38]. Webster et al. [39] observed increases in the adsorption of vitronectin on nanostructured surfaces (compared with conventional surfaces), which resulted in preferable adhesion of osteoblasts. In addition, here, the protein adsorption rate on the TNSs was correlated with the contact angle, suggesting that the hydrophilicity of titanium greatly affected its protein adsorption ability. The contact angle of the TNS and Ti sensors fluctuated in the hydrophilic range; the hydrophilicity of the surfaces expanded after treatment, corresponding to the formation of the TNSs. Thus, the growth of the titanium oxide layer increased the surface energy, resulting in a more hydrophilic surface [40].

5. Conclusions

In conclusion, TNS structures were obtained on a titanium surface via treatment with a NaOH aqueous solution at room temperature. Nanoscale network structures and a large number of nanoscale nodules were observed by SEM and SPM. In addition, the chemical composition of the TNS structures was estimated by XPS. The results confirmed the presence of a combined titanium and oxide titanate layer, which induced the adsorption of albumin and fibronectin. In the fields of tissue engineering and biomaterials, nanostructuring technologies are expected to yield novel, biologically optimized surfaces.

Conflicts of Interest

The authors declare that they have no conflicts of interest regarding the publication of this article.

Authors’ Contributions

Satoshi Komasa conceived and designed the experiments; Yuichiro Tashiro performed the experiments; Yuichiro Tashiro, Satoshi Komasa, and Akiko Miyake analyzed the data; Hiroshi Nishizaki and Joji Okazaki contributed reagents, materials, and analysis tools; Yuichiro Tashiro and Satoshi Komasa wrote the paper.

Acknowledgments

The authors wish to express their thanks to Tohru Sekino from Osaka University for setting up the nanosheets and for his supportive recommendations. The authors are also grateful to the members of the Department of Removable Prosthodontics and Occlusion and the Department of Oral Health Engineering for their advice and assistance. The authors also thank Toshio Tamaki and Hirokazu Hojyo. This work was supported by grants from the Japan Society for the Promotion of Science (16K20524).

References

M. Annunziata, A. Oliva, A. Buosciolo, M. Giordano, A. Guida, and L. Guida, “Bone marrow mesenchymal stem cell response to nano-structured oxidized and turned titanium surfaces,” Clinical Oral Implants Research, vol. 23, no. 6, pp. 733–740, 2012.
View at: Publisher Site | Google Scholar
G. Mendonca, D. Mendonca, F. J. L. Aragao, and L. F. Cooper, “Advancing dental implant surface technology–From micron-to nanotopography,” Biomaterials, vol. 29, no. 28, pp. 3822–3835, 2008.
View at: Publisher Site | Google Scholar
L. Meirelles, F. Currie, M. Jacobsson, T. Albrektsson, and A. Wennerberg, “The effect of chemical and nanotopographical modifications on the early stages of osseointegration,” International Journal of Oral and Maxillofacial Implants, vol. 23, no. 4, p. 641, 2008.
View at: Google Scholar
K. Kubo, N. Tsukimura, F. Iwasa et al., “Cellular behavior on TiO₂ nanonodular structures in a micro-to-nanoscale hierarchy model,” Biomaterials, vol. 30, no. 29, pp. 5319–5329, 2009.
View at: Publisher Site | Google Scholar
T. Kasuga, M. Hiramatsu, A. Hoson, T. Sekino, and K. Niihara, “Titania nanotubes prepared by chemical processing,” Advanced Materials, vol. 11, no. 15, pp. 1307–1311, 1999.
View at: Publisher Site | Google Scholar
X. Gao, H. Zhu, G. Pan et al., “Preparation and electrochemical characterization of anatase nanorods for lithium-inserting electrode material,” Journal of Physical Chemistry B, vol. 108, no. 9, pp. 2868–2872, 2004.
View at: Publisher Site | Google Scholar
A. R. Armstrong, G. Armstrong, J. Canales, and P. G. Bruce, “TiO₂ nanowires,” Angewandte Chemie International, vol. 43, no. 17, pp. 2286–2288, 2004.
View at: Publisher Site | Google Scholar
S. Komasa, Y. Taguchi, H. Nishida, M. Tanaka, and T. Kawazoe, “Bioactivity of nanostructure on titanium surface modified by chemical processing at room temperature,” Journal of Prosthodontic Research, vol. 56, no. 3, pp. 170–177, 2012.
View at: Publisher Site | Google Scholar
Y. Hashimoto, S. Minoura, A. Nishiura et al., “Development of titanium quartz crystal microbalance sensor by magnetron sputtering,” Journal of Oral Tissue Engineering, vol. 8, pp. 52–59, 2010.
View at: Google Scholar
A. Miyake, S. Komasa, Y. Hashimoto, Y. Komasa, and J. Okazaki, “Adsorption of saliva related protein on denture materials: an X-ray photoelectron spectroscopy and quartz crystal microbalance study,” Advances in Materials Science and Engineering, vol. 2016, Article ID 5478326, 9 pages, 2016.
View at: Publisher Site | Google Scholar
G. Mendonca, D. B. Mendonca, F. J. Aragao, and L. F. Cooper, “The combination of micron and nanotopography by H(2)SO(4)/H(2)O(2) treatment and its effects on osteoblast-specific gene expression of hMSCs,” Journal of Biomedical Materials Research A, vol. 94, no. 1, pp. 169–179, 2010.
View at: Publisher Site | Google Scholar
L. Zhao, S. Mei, P. K. Chu, Y. Zhang, and Z. Wu, “The influence of hierarchical hybrid micro/nano-textured titanium surface with titania nanotubes on osteoblast functions,” Biomaterials, vol. 31, no. 19, pp. 5072–5082, 2010.
View at: Publisher Site | Google Scholar
W. Zhang, Z. Li, Y. Liu et al., “Biofunctionalization of a titanium surface with a nano-sawtooth structure regulates the behavior of rat bone marrow mesenchymal stem cells,” International Journal of Nanomedicine, vol. 7, pp. 4459–4472, 2012.
View at: Publisher Site | Google Scholar
W. Dong, T. Zhang, J. Epstein et al., “Multifunctional nanowire bioscaffolds on titanium,” Chemistry of Materials, vol. 19, no. 18, pp. 4454–4459, 2007.
View at: Publisher Site | Google Scholar
S. Bauer, J. Park, K. von der Mark, and P. Schmuki, “Improved attachment of mesenchymal stem cells on super-hydrophobic TiO₂ nanotubes,” Acta Biomaterials, vol. 4, no. 5, pp. 1576–1582, 2008.
View at: Publisher Site | Google Scholar
E. Hosono, H. Matsuda, I. Honma, M. Ichihara, and H. Zhou, “Synthesis of a perpendicular TiO₂ nanosheet film with the superhydrophilic property without UV irradiation,” Langmuir, vol. 23, no. 14, pp. 7447–7450, 2007.
View at: Publisher Site | Google Scholar
T. Albrektsson, P. I. Brånemark, H. A. Hansson, and J. Lindström, “Osseointegrated titanium implants: requirements for ensuring a long-lasting, direct bone-to-implant anchorage in man,” Acta Orthopaedica, vol. 52, no. 2, pp. 155–170, 1981.
View at: Publisher Site | Google Scholar
H. Xing, S. Komasa, Y. Taguchi, T. Sekino, and J. Okazaki, “Osteogenic activity of titanium surfaces with nanonetwork structures,” International Journal of Nanomedicine, vol. 9, p. 1741, 2014.
View at: Publisher Site | Google Scholar
T. Fujino, Y. Taguchi, S. Komasa, T. Sekino, and M. Tanaka, “Cell differentiation on nanoscale features of a titanium surface: effects of deposition time in NaOH solution,” Journal of Hard Tissue Biology, vol. 23, no. 1, pp. 63–70, 2014.
View at: Publisher Site | Google Scholar
M. Pisarek, A. Roguska, M. Andrzejczuk et al., “Effect of two-step functionalization of Ti by chemical processes on protein adsorption,” Applied Surface Science, vol. 257, no. 19, pp. 8196–8204, 2011.
View at: Publisher Site | Google Scholar
H. M. Kim, F. Miyaji, T. Kokubo, S. Nishiguchi, and T. Nakamura, “Graded surface structure of bioactive titanium prepared by chemical treatment,” Journal of Biomedical Materials Research, vol. 45, pp. 100–107, 1999.
View at: Publisher Site | Google Scholar
M. Roser, D. Fischer, and T. Kissel, “Surface-modified biodegradable albumin nano-and microspheres. II: effect of surface charges on in vitro phagocytosis and biodistribution in rats,” European Journal of Pharmaceutics and Biopharmaceutics, vol. 46, no. 3, pp. 255–263, 1998.
View at: Publisher Site | Google Scholar
P. Roach, D. Farrar, and C. C. Perry, “Interpretation of protein adsorption: surface-induced conformational changes,” Journal of the American Chemical Society, vol. 127, no. 22, pp. 8168–8173, 2005.
View at: Publisher Site | Google Scholar
A. M. Moursi, C. H. Damsky, J. Lull et al., “Fibronectin regulates calvarial osteoblast differentiation,” Journal of Cell Science, vol. 109, pp. 1369–1380, 1996.
View at: Google Scholar
J. P. Quigley, L. I. Gold, R. Schwimmer, and L. M. Sullivan, “Limited cleavage of cellular fibronectin by plasminogen activator purified from transformed cells,” Proceedings of the National Academy of Sciences U. S. A., , vol. 84, no. 9, pp. 2776–2780, 1987.
View at: Publisher Site | Google Scholar
D. Khang, S. Y. Kim, P. Liu-Snyder, G. T. R. Palmore, S. M. Durbin, and T. J. Webster, “Enhanced fibronectin adsorption on carbon nanotube/poly (carbonate) urethane: independent role of surface nano-roughness and associated surface energy,” Biomaterials, vol. 28, no. 32, pp. 4756–4768, 2007.
View at: Publisher Site | Google Scholar
C. McFarland, C. De Filippis, M. Jenkins et al., “Albumin-binding surfaces: in vitro activity,” Journal of Biomaterials Science Polymer Edition, vol. 9, no. 11, pp. 1227–1239, 1998.
View at: Publisher Site | Google Scholar
A. Amaral, N. Alvarado, I. Marigomez, R. Cunha, K. Hylland, and M. Soto, “Autometallography and metallothionein immunohistochemistry in hepatocytes of turbot (Scophthalmus maximus L.) after exposure to cadmium and depuration treatment,” Biomarkers, vol. 7, no. 6, pp. 491–500, 2002.
View at: Publisher Site | Google Scholar
K. Endo, Y. Araki, H. Ohno, and K. Matsuda, “ESCA analysis of tarnish films on dental alloys removed from the oral cavities (Part 1) Ag-In alloys,” Journal of Dental Materials, vol. 7, pp. 184–191, 1988.
View at: Google Scholar
K. Anselme, “Osteoblast adhesion on biomaterials,” Biomaterials, vol. 21, no. 7, pp. 667–681, 2000.
View at: Publisher Site | Google Scholar
G. Balasundaram and T. J. Webster, “An overview of nano-polymers for orthopedic applications,” Macromolecular Bioscience, vol. 7, no. 5, pp. 635–642, 2007.
View at: Publisher Site | Google Scholar
R. L. Price, K. Ellison, K. M. Haberstroh, and T. J. Webster, “Nanometer surface roughness increases select osteoblast adhesion on carbon nanofiber compacts,” Journal of Biomedical Materials Research Part A, vol. 70, no. 1, pp. 129–138, 2004.
View at: Publisher Site | Google Scholar
R. Langer and D. A. Tirrell, “Designing materials for biology and medicine,” Nature, vol. 428, no. 6982, pp. 487–492, 2004.
View at: Publisher Site | Google Scholar
L. Zhang and T. J. Webster, “Nanotechnology and nanomaterials: promises for improved tissue regeneration,” Nano Today, vol. 4, no. 1, pp. 66–80, 2009.
View at: Publisher Site | Google Scholar
T. Kokubo, F. Miyaji, H. M. Kim, and T. Nakamura, “Spontaneous apatite formation on chemically surface treated Ti,” Journal of the American Ceramic Society, vol. 79, no. 4, pp. 1127–1129, 1996.
View at: Publisher Site | Google Scholar
K. Woo, G. Wei, and P. Ma, “Enhancement of fibronectin-and vitronectin-adsorption to polymer/hydroxyapatite scaffolds suppresses the apoptosis of osteoblasts,” Journal of Bone Mineral Research, vol. 17, p. 49, 2002.
View at: Google Scholar
K. Woo, R. Zhang, H. Deng, and P. Ma, “Protein-mediated osteoblast survival and migration on biodegradable polymer/hydroxyapatite composite scaffolds,” in Proceedings of Transactions of the 28th Annual Meeting of the Society for Biomaterials, Tampa, FL, USA, April 2002.
View at: Google Scholar
V. Bucci-Sabattini, C. Cassinelli, P. G Coelho, A. Minnici, A. Trani, and D. M. D. Ehrenfest, “Effect of titanium implant surface nanoroughness and calcium phosphate low impregnation on bone cell activity in vitro,” Oral Surgery, Oral Medicine, Oral Pathology, Oral Radiology, Endodontology, vol. 109, no. 2, pp. 217–224, 2010.
View at: Publisher Site | Google Scholar
T. J. Webster, C. Ergun, R. H. Doremus, R. W Siegel, and R. Bizios, “Specific proteins mediate enhanced osteoblast adhesion on nanophase ceramics,” Journal of Biomedical Materials Research, vol. 51, no. 3, pp. 475–483, 2000.
View at: Publisher Site | Google Scholar
Y. Shibata, D. Suzuki, S. Omori et al., “The characteristics of in vitro biological activity of titanium surfaces anodically oxidized in chloride solutions,” Biomaterials, vol. 31, no. 33, pp. 8546–8555, 2010.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2018 Yuichiro Tashiro et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1087

Downloads

915

Citations