Preparation of Zirconium Oxide Powder Using Zirconium Carboxylate Precursors

Al-Hazmi, Mohammed H.; Choi, YongMan; Apblett, Allen W.

doi:https://doi.org/10.1155/2014/429751

Advances in Physical Chemistry

On this page

Abstract Introduction Methods Results and Discussion Conclusions Acknowledgments Supplementary Materials References Copyright Related Articles

Research Article | Open Access

Volume 2014 | Article ID 429751 | https://doi.org/10.1155/2014/429751

Preparation of Zirconium Oxide Powder Using Zirconium Carboxylate Precursors

Mohammed H. Al-Hazmi,¹YongMan Choi,¹and Allen W. Apblett²

Academic Editor: Dennis Salahub

Received14 Sept 2014

Accepted03 Dec 2014

Published31 Dec 2014

Abstract

Zirconia was prepared at low temperatures (<450°C) using single several source precursors based on zirconium carboxylates where the R groups were systematically varied. The combination of density functional theory (DFT) calculations and extensive characterization of the precursors (i.e., X-ray diffraction, thermal gravimetric analysis, infrared spectroscopy, and scanning electron microscopy) indicated that the carboxylic acid complexes may link the zirconium metal with a cis bidentate configuration. Periodic DFT calculations were performed to examine the interaction between monoclinic ZrO₂ and propanoic acid. Dissociative adsorption takes place through the cis bidentate structure with an adsorption energy of −1.43 eV. Calculated vibrational frequencies using the optimized structure are in good agreement with experimental findings.

1. Introduction

While zirconia (ZrO₂) finds extensive use as a ceramic material it also has important applications in catalysts [1]. Due to its unique chemical properties (i.e., surface acidity and basicity [2, 3]), it is a valuable catalyst for elimination, dehydration, hydrogenation, and oxidation. As reported previously [4, 5], the properties of tetragonal zirconia (t-ZrO₂) that is employed in the aforementioned applications are highly dependent on the precursors used for its preparation. To date, most interest has focused on the preparation of a stable ZrO₂ powder at <450°C by using different precursors [6] including zirconium carboxylates. The latter can be prepared straightforwardly by the reaction of sodium carboxylate with an aqueous solution of a zirconium salt [7], leading to the linking of zirconium cations to the carboxylate anions. One of the most widely used precursors for the synthesis of zirconia may be zirconium acetate-based ones [8–13]. For example, zirconium tetraacetate can be prepared by the reaction of zirconium tetrachloride with an excess of acetic acid at 80°C [8]. Refluxing the mixture to the boiling point produces the formation of zirconium oxyacetate [8, 9]. Zirconium oxyacetate, Zr₄O₃(CH₃COO)₁₀·3H₂O, can be also prepared by refluxing of a small amount of zirconium oxychloride with acetic acid [14]. Recently, Guo and Chen [15] reported a novel zirconium oxy-hydroxy acetate complex synthesized from zirconium oxychloride and acetic acid solution, followed by a precipitation with concentrated ammonium hydroxide at pH = 6. The product was determined to be Zr₄O₃(OH)₇(CH₃COO)₃·5H₂O and produced a tetragonal zirconium oxide phase with a crystallite size of 30 nm when pyrolyzed at 545°C. Regardless of the numerous studies, few studies have been carried out to investigate the preparation of zirconia from zirconium carboxylates complexes with varying R-groups and their influence on the properties of the oxides from them. Therefore we recently reported a benchmark study using zirconium benzilate as a single source precursor for the synthesis of zirconia [16]. To more systematically understand the synthesis approach, the zirconia synthesis was executed with various types of carboxylate complexes derived from aliphatic and α-hydroxyl carboxylic acids. In addition, periodic density functional theory (DFT) simulations were applied to support the experimental observation from infrared spectroscopy (IR).

2. Methods

2.1. Experimental

Summarized in Table S1 (in Supplementary Materials available online at http://dx.doi.org/10.1155/2014/429751) are the chemical structures of the carboxylic acids used for the preparation of the zirconium carboxylates. Aqueous ammonium hydroxide (NH₄OH, Scientific Products), zirconium oxychloride (ZrOCl₂·8H₂O, Alfa Aesar), sodium bicarbonate (NaHCO₃, Alfa Aesar), 2-ethylhexanoic acid (C₈H₁₆O₂, MCB), α-hydroxyisobutyric acid (C₄H₈O₃, Fluka), propanoic acid (C₃H₆O₂, Aldrich), sodium butyrate (C₄H₇O₂Na, Aldrich), isobutyric acid (C₄H₈O₂, Aldrich), pivalic acid (C₅H₁₀O₂, Aldrich), mandelic acid (C₈H₈O₃, Aldrich), and hydroxypivalic acid (C₅H₁₀O₃, Aldrich) were used without further purification. Zirconium carboxylates precursors were prepared from the reaction of zirconium oxychloride with the sodium or ammonium carboxylic acid salts of the acids listed above. These syntheses are summarized in Table S2. The yields using zirconium carboxylate precursors were ~90%. The precipitates were washed several times with distilled water and subsequently dried in an oven at 120°C for 12 hours. They were then calcined at different temperatures in air. The chloride content was determined using a conventional gravimetric analysis [17] to confirm that no chloride ions were left in the solution.

The precursors and zirconia powders were characterized by the Brunauer-Emmett-Teller (BET) multilayer nitrogen adsorption method (Quantachrome Nova 1200), thermogravimetric analyses (Seiko EXSTAR 6000 TG/DTA 6200), scanning electron micrograph (SEM) (JEOL JXM 6400), diffuse reflectance infrared spectroscopy (Nicolet Magna-IR 750), and X-ray powder diffraction (XRD) patterns using copper K_α radiation with a wavelength of 1.5418 Å (Bruker AXS D8). The volume fraction of the tetragonal and monoclinic phases (t-ZrO₂ and m-ZrO₂, resp.) and the relative ratio of t-ZrO₂ to m-ZrO₂ were determined using the method proposed by Toraya and coworkers [18] (see supporting information).

2.2. Computational

To examine the interaction between zirconia and carboxylic acid, periodic DFT calculations [19] were performed using Vienna ab initio simulation package (VASP) [20, 21]. The projector augmented wave method (PAW) [22] with the generalized gradient approximation (GGA) using the Perdew-Burke-Ernzerhof (PBE) functional [23] was used. In keeping with previous studies [16, 24], a stable () plane with a (2 × 2) surface was utilized. Similar to the previous study [24], a supercell with 16 Zr and 32 O atoms was constructed. A vacuum space of 15 Å and a 415 eV kinetic energy cut-off for a plane wave basis set was applied. The Monkhorst-Pack [25] meshes with (3 × 3 × 3) and (3 × 3 × 1) k-points were used for bulk and surface calculations, respectively. For 2D surface calculations, half of the atomic layers were fixed to the bulk structure, and the remaining layers and the adsorbate were fully relaxed. Adsorption energies (E_ads) were defined as E_ads = E(adsorbate/ZrO₂) − E(ZrO₂) − E(adsorbate), where E(adsorbate/ZrO₂), E(ZrO₂), and E(adsorbate) are the calculated energies of a carboxylic acid on zirconia, a bare zirconia, and gas-phase carboxylic acid. The surface coverage was 25% [24]. To support the infrared spectroscopic measurements, frequencies were also calculated on the basis of the optimized structures. In this study, we applied the same k-point used for geometry optimization since our previous study showed the minor difference between prediction and experiment [16].

3. Results and Discussion

3.1. Zirconium Carboxylate Precursors for Zirconia

Representative TGA curves for propionate, pivalate, 2-ethylhexanoate, and mandelate are shown in Figure 1. These demonstrate that the weight loss is correlated with the nature of the carboxylate ligands of the precursors and clearly show that the weight loss starts at room temperature and is complete between 400 and 500°C. Furthermore, the TGA results illustrate that the total weight loss of the zirconium α-hydroxyl carboxylate complexes (Figure 1(b)) is lower than that of the aliphatic zirconium carboxylates (Figure 1(a)). The reason may be the ability of the α-hydroxyl carboxylates to chelate to a zirconium ion via the hydroxyl and the carboxylate. The formula weights of the complexes were calculated from the ceramic yields of ZrO₂ from the TGA data. These were combined with the carbon and hydrogen content from elemental analysis to yield the proposed formulae for the zirconium carboxylates that are compiled in Table 1.

(a)

(b)

The low angle XRD patterns of the calcined zirconium pivalate complex at 25°C, 250°C, and 300°C suggest the formation of a mesoporous solid (Figure 2). A single broad diffraction peak was observed with a d-spacing of 14.3 Å, 18.1 Å, and 20.0 Å for the freshly synthesized complex and the products from its calcination at 250°C and 300°C, respectively. The breadths of the reflection peaks reflect either a distribution of pore sizes or an organization of the pores in limited regions of the solid. The BET analysis of the zirconium pivalate complex shows a high surface area of 297 m²/g, supporting an ordered porous structure. As shown in Figure 2, as the d-spacing increases, the scattering intensity decreases. This may indicate that the structure undergoes a contraction during the calcination and is transformed into a less ordered structure by the removal of the alkyl groups. This is also confirmed by the sharp decrease of the specific surface area during the calcination due to the collapse of the structure. The observed increase in the d-spacing might be due to the loss of adsorbed water molecules and a gradual thermal decomposition of the alkyl groups, leading to longer pores and an expansion in the distance between the structure layers. As reported previously [17, 18], the polymerization of the zirconium carboxylate tetramer may take place due to the presence of the OH groups forming a bridge between two tetramers. Such a polymerization process could be the reason for the formation of the high surface area porous zirconium carboxylates. As listed in Table 1, the synthesized zirconium α-hydroxyisobutyrate (Zr-9) contains a large number of water molecules as compared to the other carboxylates. The extra water may be ascribed to water molecules that are linked to zirconium ion, resulting in a high polarization that induces strong interactions with other water molecules via hydrogen bonding.

Infrared spectroscopy was performed to examine the coordination modes of the carboxylate ligands. It is known that the carboxylate ligands bound in a bridging bidentate configuration have a value of about 160 cm⁻¹ (splitting between the asymmetric and symmetric carbonyl stretching frequencies), while chelating bidentate carboxylates have a smaller value (100 cm⁻¹ or less). Monodentate carboxylates, on the other hand, result in a greater value of about 200 cm⁻¹ [26, 27]. The infrared spectrum of the zirconium aliphatic carboxylate, zirconium propionate (Zr-1) (Figure 3(a)), shows a band centered at 3,377 cm⁻¹ corresponding to the hydrogen bonded O–H stretching band, while that at 3,643 cm⁻¹ is related to the stretching mode for free OH. The bands at 2,980 cm⁻¹ and 2,930 cm⁻¹ can be assigned to the asymmetric and symmetric methyl groups of the carboxylate ligands, respectively, while that at 1,340 cm⁻¹ is attributed to the vibration mode of the CH₃ group. The bands around 1,560 cm⁻¹ and 1,439 cm⁻¹ correspond to the asymmetric and symmetric carboxylate stretching vibrations, respectively. The IR band at about 1,470 cm⁻¹ is attributed to the bending modes for CH₃ and C–O–H. Table 2 lists the stretching frequencies of the carboxylate carbonyl group and and the splitting () between the asymmetric and symmetric carbonyl stretching frequencies of the zirconium carboxylate complexes. The values of α-hydroxy carboxylate zirconium complexes were in the range 227–274 cm⁻¹, while the other zirconium carboxylate complexes showed lower values in the range 121–152 cm⁻¹. The lower values for nonhydroxylated zirconium carboxylates may be attributed to a bridging bidentate bonding mode for the carboxylates. The results in Table 2 also show that the values for the zirconium carboxylates increase slightly with increasing chain length or branching of the carboxylate ligands. Among the aliphatic carboxylates, the propionate (Zr-2) has the lowest value of 121 cm⁻¹, while pivalate (Zr-5) has the highest value of 152 cm⁻¹. Furthermore, the aliphatic complexes (i.e., zirconium propionate, zirconium pivalate, zirconium hydroxypivalate, and 2-ethylhexanoate) show lower asymmetric stretching frequencies of the carbonyl groups than the α-hydroxyl carboxylate zirconium complexes. A large shift of the carbonyl stretching frequencies between the free acid carbonyl (1,700–1,730 cm⁻¹) and the complexes (1,560–1,580 cm⁻¹) was observed. This shift is due to the fact that when the zirconium metal coordinates to the oxygen moiety of the carbonyl group in the carboxylate ligands with a bidentate configuration, the C–O bonds are weakened due to the sharing of the carbonyl oxygen electrons in the bonding to the zirconium ions. In contrast, the α-hydroxyl carboxylate complexes showed a higher asymmetric stretching for the carbonyl groups (1,620–1,650 cm⁻¹). This may be due to the chelation of one oxygen atom of the carbonyl group and the oxygen of the α-hydroxyl group to the zirconium ion to a five-membered ring. This will result in a monodentate carboxylate that is expected to have a large value.

(a)

(b)

(c)

3.2. Zirconia Prepared from Zirconia Carboxylate Complexes

Figures 3(b) and 3(c) show the infrared spectra of the products obtained from the pyrolysis of the zirconium propionate complex at different calcination temperatures. These display a sharp band at about 2,339 cm⁻¹ that is attributed to the adsorbed CO₂ species on the surface that resulted from the thermal decomposition of the carboxylate ligand. This assignment is in good agreement with previous studies on the adsorption of CO₂ onto ZrO₂ and modified ZrO₂ [28, 29]. The peak observed at about 1,424 cm⁻¹ for the zirconium propionate calcined at 470°C (Figure 3(b)) probably corresponds to the presence of some carbonate species adsorbed on the surface of t-ZrO₂. The calcined sample at 470°C shows a band at 1,533 cm⁻¹ attributed to bidentate carbonate species present on the oxide surface. It is noted that according to the TGA analysis, about 40% of its weight was lost when calcined at ~470°C, corresponding to the expected loss for ZrO₂ formation. However, the sample color was still brown at this calcination temperature, indicating that the band at 1,533 cm⁻¹ may be due to the bidentate carbonate and carbon species deposited on the oxide surface not the ZrO₂ formation [28, 30]. The intensity of this peak decreased at the calcination temperature of 720°C (Figure 3(c)). The band observed at ~790 cm⁻¹ for the sample calcined at 470°C is probably due to the carbonate-water interaction. With increase in the calcination temperature, the intensity of this band decreased.

As described above, periodic DFT calculations were carried out to understand the interaction between stable m-ZrO₂ and acetic acid and propanoic acid. We chose the two acids since acetic acid is the smallest carboxyl acid, while propanoic acid is the smallest one used in the experiment. For the zirconia surface, a stable (2 × 2) () plane was used as a surface. In this study, the cis configuration was examined, in accordance with a previous study [24], since the cis configuration is more stable than the trans configuration. Figure 4 schematically depicts the gas-phase acetic and propanoic acids. In addition, it was found that both acetic and propanoic acids are dissociatively adsorbed on the surface and their adsorption energies are −1.39 eV and −1.43 eV, respectively. Both of the cis structures have similar Zr-O distances (~2.2 Å), while those of the H from the OH group are 2.51 Å and 2.46 Å, indicating total dissociation. Based on the structure of propanoic acid (Figure 4(b)), a vibrational-frequency calculation was executed to compare with the experimental results (Figure 3(a) and Table 2). Its surface OH stretching mode is calculated to be 3,605 cm⁻¹, which is close to the typical OH stretching of Zr-1 (Figure 3(a); 3,643 cm⁻¹). In particular, the calculated asymmetric mode for COO is 1,497 cm⁻¹, which is also in line with the experimental finding of 1,564 cm⁻¹ (Table 2). The vibrational-frequency simulations along with geometry optimization support the conclusion that the cis bidentate structure is preferred to the trans configuration. As a matter of fact, it is highly difficult to construct a more plausible model to simulate the zirconium carboxylates as proposed (Table 1; [Zr₄O₂(OH)₅(OAP)₅Cl₂]·8H₂O). However, if one takes into account the hydrogen bond, more accurate results could be produced.

(a)

(b)

X-ray powder diffraction demonstrated that the pyrolysis product from zirconium propionate at 230°C is amorphous (Figure 5). With further heating to 420°C, a mixture of tetragonal and cubic phases started to appear as a result of the transformation of the zirconium carboxylate to ZrO₂. Upon heating to 590°C, a more crystalline t-ZrO₂ phase was observed. Then, as the oxide was heated above 600°C, a phase transformation occurred from the tetragonal phase to the monoclinic one. When the oxide was further calcined to 800°C, the monoclinic phase was the dominant phase with about 90% relative abundance. In this study, a general trend was found for the phase transformation from the tetragonal to monoclinic phase with the initial crystallization of ZrO₂ being detected between 350°C and 450°C.

Figure 6 shows the ZrO₂ crystallite size distribution calculated by application of Scherrer’s equation [31] to the XRD patterns for zirconium propionate calcined at different temperatures. A slight increase in the average crystallite size from 3.2 nm to 6.7 nm was observed when the precursor was heated at 590°C and 720°C, respectively. A bigger average crystallite size of 18.4 nm was observed when the sample calcined at 800°C, in which the powder is almost completely transformed into the monoclinic phase (Table S3).

The phase transformation data and the surface area values are presented in Table S3. The results show that the zirconium oxides derived from aliphatic zirconium carboxylates undergo a phase transformation to the monoclinic system at higher temperature (>720°C) than the α-hydroxyl carboxylate complexes. The oxides derived from the thermal calcination of zirconium mandelate and zirconium hydroxybutyrate transformed into the monoclinic phase rapidly in the temperature range of 600°C to 720°C. It can be concluded that the different coordination mode α-hydroxy acids to zirconia leads to a different decomposition pathway that produces amorphous zirconium oxide with a structure predisposed to formation of monoclinic zirconia.

As depicted in Table S3 and Figure 7, the surface area results for the zirconium precursors showed a slight increase by the calcination due to the loss of the ligand and the formation of oxides with open pores. Further heating led to the gradual sintering of the oxide particles and decrease in the surface area. The precursors that showed a long order range and very high surface areas (zirconium pivalate) exhibited a sharp decrease in the surface area due to the collapse of the metalloorganic framework upon formation of the oxide and then a slow decrease in the surface area due to the sintering process. Furthermore, ZrO₂ obtained from the aliphatic carboxylates (Table S3) showed a dependence on the carboxylate ligands: the longer the carboxylate ligand chain, the higher the surface area of the resulting zirconia. For example, ZrO₂ obtained from zirconium ethylhexanoate (Zr-7) showed a relatively higher surface area compared to that prepared from the other aliphatic zirconium carboxylate complexes. Also, to examine the influence of the zirconium carboxylate precursor on the morphology of the final oxide, scanning electron microscopy was performed. Figure 8 shows the SEM images of ZrO₂ derived from the thermal treatment of the zirconium pivalate complex (Zr-5) at 400°C, demonstrating the formation of agglomerates containing spherical nanosize particles with an approximate average diameter of about 100–200 nm.

(a)

(b)

4. Conclusions

Zirconia was prepared form of a variety of zirconium carboxylate complexes that were synthesized by the reaction of zirconium oxychloride with carboxylic acids or carboxylate salts in aqueous media. The carboxylates used in this study included aliphatic carboxylic acids and α-hydroxyl carboxylic acids. It was determined that the aliphatic zirconium carboxylate complexes coordinate to the zirconium ions in a bridging bidentate mode, while a bridging chelating bonding with incorporation of the OH in the bonding was observed with the α-hydroxyl carboxylate complexes. A vibrational-frequency calculation with a simplified structure of propanoic acid on m-ZrO₂ supports that a cis bidentate configuration is a more plausible structure. Notably, it was found that the nature of the zirconium carboxylate plays a profound role in the crystallinity, surface area, and other properties of the zirconia produced by their decomposition.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors acknowledge SABIC’s management for the financial support of this research. DFT calculations were performed at KAUST Supercomputing Laboratory.

Supplementary Materials

The structures of carboxylic acids and zirconium carboxylates, the structures and properties of zirconium carboxylate complexes, and surface areas and phase composites of ZrO₂ are summarized.

Supplementary Material

References

M. Stoia, P. Barvinschi, L. Barbu-Tudoran, A. Negrea, and F. Barvinschi, “Influence of thermal treatment on the formation of zirconia nanostructured powder by thermal decomposition of different precursors,” Journal of Crystal Growth, vol. 381, pp. 93–99, 2013.
View at: Publisher Site | Google Scholar
K. T. Jung and A. T. Bell, “Effects of catalyst phase structure on the elementary processes involved in the synthesis of dimethyl carbonate from methanol and carbon dioxide over zirconia,” Topics in Catalysis, vol. 20, no. 1–4, pp. 97–105, 2002.
View at: Publisher Site | Google Scholar
N. V. Vlasenko, Y. N. Kochkin, and P. E. Strizhak, “Effect of acid-base characteristics of ZrO₂-Y2O₃ on catalytic properties in carboxylation of methanol,” Theoretical and Experimental Chemistry, vol. 45, no. 4, pp. 271–275, 2009.
View at: Publisher Site | Google Scholar
W. H. Rhodes, “Controlled transient solid second-phase sintering of yttria,” Journal of the American Ceramic Society, vol. 64, no. 1, pp. 13–19, 1981.
View at: Publisher Site | Google Scholar
F. F. Lange, “Transformation toughening,” Journal of Materials Science, vol. 17, no. 1, pp. 240–246, 1982.
View at: Publisher Site | Google Scholar
R. N. Kapoor and R. C. Mehrotra, “Organic compounds of zirconium. V. Studies of zirconium mandelates,” Journal of the American Chemical Society, vol. 80, no. 14, pp. 3569–3573, 1958.
View at: Publisher Site | Google Scholar
W. Blumenthal, The Chemical Behavior of Zirconium, Van Nostrand Company, Princeton, NJ, USA, 1958.
R. C. Paul, O. B. Baidya, R. C. Kumar, and R. Kapoor, “Zirconium(IV) carboxylates,” Australian Journal of Chemistry, vol. 29, no. 7, pp. 1605–1607, 1976.
View at: Publisher Site | Google Scholar
N. W. Alcock, V. M. Tracy, and T. C. Waddington, “Acetates and acetate-complexes. Part 1. Preparation of acetato-complexes and conductimetric studies in the acetic anhydride solvent system,” Journal of the Chemical Society, Dalton Transactions, no. 21, pp. 2238–2242, 1976.
View at: Publisher Site | Google Scholar
M. L. Balmer, F. F. Lange, and C. G. Levi, “Metastable phase selection and partitioning in ZrO₂–MgO processed from liquid precursors,” Journal of the American Ceramic Society, vol. 75, no. 4, pp. 946–952, 1992.
View at: Publisher Site | Google Scholar
A. C. Geiculescu and H. G. Spencer, “Thermal decomposition and crystallization of aqueous sol-gel derived zirconium acetate gels: effects of the precursor solution pH,” Journal of Sol-Gel Science and Technology, vol. 16, no. 3, pp. 243–256, 1999.
View at: Publisher Site | Google Scholar
F. J. Berry, S. J. Skinner, I. M. Bell, R. J. H. Clark, and C. B. Ponton, “The influence of pH on zirconia formed from zirconium (IV) acetate solution: characterization by X-ray powder diffraction and Raman spectroscopy,” Journal of Solid State Chemistry, vol. 145, no. 2, pp. 394–400, 1999.
View at: Publisher Site | Google Scholar
A. Samdi, B. Durand, M. Roubin et al., “Pressing and sintering behaviour of yttria stabilized zirconia powders prepared from acetate solutions,” Journal of the European Ceramic Society, vol. 12, no. 5, pp. 353–360, 1993.
View at: Publisher Site | Google Scholar
L. N. Kommisarova, “New oxyacetates of zirconium and hafnium,” Russian Journal of Inorganic Chemistry, vol. 8, no. 1, pp. 56–62, 1963.
View at: Google Scholar
G.-Y. Guo and Y.-L. Chen, “Preparation and characterization of a novel zirconia precursor,” Ceramics International, vol. 30, no. 3, pp. 469–475, 2004.
View at: Publisher Site | Google Scholar
M. H. Al-Hazmi, Y. Choi, and A. W. Apblett, “Synthesis of zirconium oxide at low temperature using zirconium benzilate: an experimental and computational study,” Science of Advanced Materials, vol. 6, no. 7, pp. 1438–1444, 2014.
View at: Publisher Site | Google Scholar
G. Svehla, Vogel's Quantitative Inorganic Analysis, Longman, London, UK, 7th edition, 1997.
H. Toraya, M. Masahiro, and S. Somiya, “Calibration curve for quantitative analysis of the monoclinic-tetragonal ZrO₂ system by X-ray diffraction,” Journal of the American Ceramic Society, vol. 67, no. 6, pp. C119–C121, 1984.
View at: Publisher Site | Google Scholar
W. Kohn and L. J. Sham, “Self-consistent equations including exchange and correlation effects,” Physical Review, vol. 140, no. 4, pp. A1133–A1138, 1965.
View at: Google Scholar | MathSciNet
G. Kresse and J. Hafner, “Ab initio molecular dynamics for liquid metals,” Physical Review B, vol. 47, no. 1, pp. 558–561, 1993.
View at: Publisher Site | Google Scholar
G. Kresse and J. Furthmüller, “Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set,” Physical Review B: Condensed Matter and Materials Physics, vol. 54, no. 16, pp. 11169–11186, 1996.
View at: Publisher Site | Google Scholar
P. E. Blöchl, “Projector augmented-wave method,” Physical Review B, vol. 50, no. 24, pp. 17953–17979, 1994.
View at: Publisher Site | Google Scholar
J. P. Perdew, K. Burke, and M. Ernzerhof, “Generalized gradient approximation made simple,” Physical Review Letters, vol. 77, no. 18, pp. 3865–3868, 1996.
View at: Publisher Site | Google Scholar
A. V. Ignatchenko, “Density functional theory study of carboxylic acids adsorption and enolization on monoclinic zirconia surfaces,” The Journal of Physical Chemistry C, vol. 115, no. 32, pp. 16012–16018, 2011.
View at: Publisher Site | Google Scholar
H. J. Monkhorst and J. D. Pack, “Special points for Brillouin-zone integrations,” Physical Review B, vol. 13, no. 12, pp. 5188–5192, 1976.
View at: Publisher Site | Google Scholar | MathSciNet
K. Nakamoto, Infrared and Raman Spectra of the Inorganic and Coordination Compounds, Wiley, New York, NY, USA, 5th edition, 1997.
G. Deacon and R. Phillips, “Relationships between the carbon-oxygen stretching frequencies of carboxylato complexes and the type of carboxylate coordination,” Coordination Chemistry Reviews, vol. 33, no. 3, pp. 227–250, 1980.
View at: Publisher Site | Google Scholar
V. Bolis, G. Magnacca, G. Cerrato, and C. Morterra, “Effect of sulfation on the acid-base properties of tetragonal zirconia. A calorimetric and IR spectroscopic study,” Topics in Catalysis, vol. 19, no. 3-4, pp. 259–269, 2002.
View at: Google Scholar
C. Morterra, M. Peñarroya Mentruit, and G. Cerrato, “Acetonitrile adsorption as an IR spectroscopic probe for surface acidity/basicity of pure and modified zirconias,” Physical Chemistry Chemical Physics, vol. 4, no. 4, pp. 676–687, 2002.
View at: Publisher Site | Google Scholar
V. Bolis, G. Magnacca, G. Cerrato, and C. Morterra, “Microcalorimetric and IR-spectroscopic study of the room temperature adsorption of CO₂ on pure and sulphated t-ZrO₂,” Thermochimica Acta, vol. 379, no. 1-2, pp. 147–161, 2001.
View at: Publisher Site | Google Scholar
A. W. Apblett, S. I. Kuriyavar, and B. P. Kiran, “Preparation of micron-sized spherical porous iron oxide particles,” Journal of Materials Chemistry, vol. 13, no. 5, pp. 983–985, 2003.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2014 Mohammed H. Al-Hazmi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

8920

Downloads

1762

Citations