Abstract

Energy recovery potential of a mesophilic co-digester treating OFMSW and primary sludge at an integrated biomethanization plant was investigated based on feasibility study results. Since landfilling is still the main solid waste disposal method in Turkey, land scarcity will become one of the most important obstacles. Restrictions for biodegradable waste disposal to sanitary landfills in EU Landfill Directive and uncontrolled long-term contamination with gas emissions and leachate necessitate alternative management strategies due to rapid increase in MSW production. Moreover, since energy contribution from renewable resources will be required more in the future with increasing oil prices and dwindling supplies of conventional energy sources, the significance of biogas as a renewable fuel has been increased in the last decade. Results indicated that almost 93% of annual total cost can be recovered if 100% renewable energy subsidy is implemented. Besides, considering the potential revenue when replacing transport fuels, about 26 heavy good vehicles or 549 cars may be powered per year by the biogas produced from the proposed biomethanization plant (PE = 100,000; XPS = 61 g TS/PE·day;  g TS/PE·day).

1. Introduction

Primary energy sources are classified as fossil and renewable energy sources and nuclear fuels. Globally, most energy is provided from the fossil energy sources whereas nuclear power plants contribute to only a very small percentage. Therefore, the dependence of the global economy on fossil-derived fuels, coupled with political instability in oil-producing countries, has pushed petroleum prices near all-time highs. On the other hand, although energy supply from renewable energy sources has been improved significantly, its contribution is quite limited. Water, sun, wind, geothermal heat, tides, and biomass are reported as the renewable energy sources. Since demand for energy is expected to increase more than 50% by 2025, there is an ongoing search to develop sustainable, affordable, environmentally sound energy from renewable sources [1, 2]. Biofuels derived from plant-based feedstocks, such as corn and sugarcane, are considered renewable and are an environmentally clean energy source, and they have potential to significantly decrease fossil fuel consumption. Bioethanol and biodiesel can be used in the form of a gasoline/diesel blend [2]. Besides, biogas which is produced at most biological treatment plants has been considered as one of the most important renewable energy sources. Anaerobic biotechnology has been reported as a sustainable alternative to current disposal strategies because the volume of the organic waste is reduced and stabilized, a residue (compost) that can be used for soil conditioning is produced, and energy in the form of methane is recovered [3]. Methane production can be estimated from chemical oxygen demand (COD) or ultimate biochemical oxygen demand (BODL) stabilization based on the fact that 1 kg COD destroyed produces 0.35 m3 CH4 at standard temperature and pressure (STP). Although methane generation is the focus, anaerobic biotechnology may also convert organic-rich waste streams into hydrogen or ethanol. Temperature, pH, alkalinity, hydraulic and organic loading rates, the presence of toxic and inhibitory substances, type of substrate, and total solids (TS)/volatile solids (VS) content are the factors affecting the amount of gas produced. The methane content of biogas is also very important, because it imparts fuel value to the gas. It was reported that biogas, produced during anaerobic digestion of biodegradable organic solids, typically contains about 60–65% methane, which is a valuable resource and can be used to offset part of the energy needs for in-plant use. The produced biogas can replace natural gas, coal, and electricity. Moreover, the residues resulting from anaerobic digestion are rich in nutrients (N and P) and can be land applied which also significantly reduce use of chemical fertilizer. In addition, the treated effluent can be recycled as process water for in-plant use [2, 4].

In the countries like Turkey where landfilling is still the main solid waste management method, land scarcity will become one of the most important obstacles for municipal solid wastes (MSW) disposal. It was reported that ca. 60 × 103 tonnes of MSW are produced per day in Turkey, which includes almost 50% biodegradable materials. For instance in Istanbul, almost 45% of the produced MSW is in organic nature whereas 34% of it may be recovered and 21% is composed of miscellaneous materials. Thus, MSW should be considered as the “valuable products” instead of the “wastes” [5]. In the framework of the Kyoto agreements, which Turkey has already signed, the production of methane from wastes should be encouraged, for example, by subsidizing electricity from biogas with the net added price of as much as 0.1 per kWh. Since current biomethane potential of the produced OFMSW in Turkey is about 109 m3 CH4 per year considering 50% biomethanization of 5 × 106 ton/year biodegradable waste as volatile solids (VSs), the biomethanization of OFMSW can become a feasible option by applying subsidies to electricity production from wastes [6]. In year 2000, the law of “Renewable Energies,” which stated the rules for the subsidization of the power supplied by biogas facilities, became effective in Europe [1]. It was reported that around the world, the potential for biogas production is so large that it could replace about 20–30% of total natural gas consumption [4]. Moreover, the restrictions for biodegradable waste disposal in EU Landfill Directive [7] and uncontrolled long-term contamination with gas emissions and leachate necessitate alternative sustainable and integrated management strategies due to rapid increase in the production of MSW, that is, anaerobic biological treatment, either in anaerobic digesters or in landfill bioreactors [8, 9]. It was reported that most wastes with a high-solid content, for example, municipal sludge (primary solids and waste-activated sludge (WAS)), animal manure, food wastes, and agricultural residues contain a significant amount of biodegradable organic carbon. These organic-rich wastes and residues are ideal feedstocks for renewable energy (methane, hydrogen, or butanol) generation through nonoxidative metabolism (anaerobic fermentation) [10]. Codigestion of the organic fraction of municipal solid wastes (OFMSW) with other cosubstrates is reported as an attractive alternative for sustainable management of different separate waste streams produced at large amounts. Since codigestion concept involves the treatment of several types of waste in a single treatment facility, mixing of several waste types has positive effects both on the anaerobic digestion process itself and on the treatment economy which shows itself with an increase in methane yield and in process stability. The most appropriate cosubstrate alternatives for codigestion with OFMSW are reported as the sewage sludge which provides codigestion application to be realised in existing digesters at the treatment plants without great investments, a situation which makes this alternative more appealing. Moreover, theoretical CH4 content for primary sludge is reported as about 63% [3, 4].

The aim of this study is to evaluate energy recovery potential if mesophilic (30–35°C) codigestion of OFMSW with primary sludge is applied at a full-scale municipal wastewater treatment plant (WWTP) for 100,000 population equivalent (PE) (Figure 1). Here, the treatment plant is composed of an activated sludge system (C, N, and P removal) with presedimentation. The produced primary sludge will be codigested with the mixed wastes originating from the restaurants and canteens and from the supermarkets (greengrocery part) where both waste streams were the source sorted organic fraction of the municipal solid wastes (SS-OFMSWs). In the scope of this study, feasibility, biogas production and its potential revenue when replacing transport fuels (i.e., diesel or gasoline) were investigated for the proposed integrated biomethanization plant.

2. The Mass Balance Calculations

In order to calculate the fundamental data for the process design and to establish the mass balance, first of all the produced primary sludge and the OFMSW should be determined. The typical raw primary sludge production and its total solids (TSs) content from a municipal wastewater treatment plant are given in the ranges of 0.92–2.20 L/PE·day and 2–8%, respectively [11]. If raw primary sludge production and its TS content are assumed as 1.5 L/PE·day and 4%, respectively, primary sludge amount (XPS) is calculated as about 61 g/PE·day (density 1010 kg/m3). TS content and VS/TS ratio for the SS-OFMSW from the restaurants and canteens are given in the range of 21.4–27.4% and 91–99%, respectively. On the other hand, TS content and VS/TS ratio for the SS-OFMSW from the greengrocery parts of the supermarkets are given in the range of 5.4–13.3% and 78–92%, respectively.

The OFMSW production from municipal sources is about 0.25 kg/PE·day. If the mixed SS-OFMSW production from the restaurants and canteens and from the greengrocery parts of the supermarkets is assumed as 20% of this amount, SS-OFMSW amount () per capita is calculated as about 50 g/PE·day (TS = 12%; VS/TS = 90%; density 1015 kg/m3). If it is assumed that 20% of dual (separate) sorted (DS) OFMSW originating from households (only kitchen wastes) is added, amount will increase to about 100 g/PE·day (i.e., 0.25 × 0.2 + 0.05 = 0.1 kg/PE·day). The amount of the would increase if DS-OFMSW addition is more than 20%. In the light of the above given data, the flowrates of raw primary sludge and SS-OFMSW as the influents of the pulper (Figure 1) can be calculated as about 150 and 41 m3 per day, respectively, for the 100,000 PE plant. The effluent of the pulper is composed of the supernatant and the bottom phases which can be calculated as about 3 and 4 m3 per day, respectively. Therefore, the flowrate of the mid-phase (Figure 1) of the pulper (which is the influent of the anaerobic codigester when primary sludge is given to the effluent stream of the grinder) is about 184 m3/day with a TS content of about 5.5%. The results of the above calculations are summarized and explained in Table 1.

3. Biomethane Recovery as a Potential Energy Source

Since daily methane production is calculated as about 2220 m3 (Table 1), total annual savings based on electricity and heat energies can be determined as about 263,350 using (1) as follows: However, since it is assumed that 85% of this energy can be sold in the market, net energy income is expected to be ca. 223,850/yr. Here, energy potential per m3 of methane is approximately 33,810 kJ which corresponds to about 10 kWh. Unit energy selling prices are assumed according to Turkey’s current market conditions, that is, 0.07 for electricity and 0.02 for heat per kWh, respectively. If the above calculations are repeated according to  g/PE·day ( t/day for PE = 100,000), daily methane production is calculated as about 2980 m3 which corresponds to net energy income of about 300,500. Hence, results indicated that energy savings that can be recovered annually from the proposed biomethanization plant would be in the range of 2.24–3.00 per capita by the codigestion of the primary sludge and SS-OFMSW. This range may increase to 4.48–6.00/PE·year if 100% renewable energy subsidy is implemented. It was observed that over the past few years, the number of biogas facilities has been continuously rising in Europe, especially after implementing even higher subsidies. For example, in Germany about 1500 biogas facilities were in use. From these 1500 installed facilities, about 720 MW electric power production is reported [1].

4. Total Cost of the Biomethanization Plant

Pretreatment of the feedstock is generally essential to enhance their digestibility and bioenergy generation potential because it was reported that one major challenge to the feedstocks is their slow digestibility and the rate-limiting hydrolysis step. In order to accelerate digestion, various pretreatment methods are applied such as mechanical, thermal, chemical, or biological which help solubilize particulate matter. Pretreatment would become a standard practice for all high-solids organic wastes and residues in the coming years [10]. In the scope of this study, a preliminary treatment unit (PTU) is included for the pretreatment of the SS-OFMSW before the mesophilic anaerobic codigester. This unit consists of a magnet by which the metals are separated, a grinder, and a pulper. The primary sludge is not subjected to magnet and grinder but may be given to the effluent stream of the grinder when needed. In order to calculate total project cost including investment and operation and maintenance (O&M) costs for the proposed integrated biomethanization plant, the cost for PTU (magnet, grinder, and pulper) should be determined. For this purpose, primary components of the investment cost which were already determined for a biomethanization plant treating OFMSW and the primary sludge for a PE = 200,000 capacity were taken into consideration [12]. According to the study, the primary investment cost components were construction including preconstruction (engineering and consultancy) and civil works as ~2.5 × 106, equipment (mechanical, electrical, instrumentation, piping, and mounting) as ~1.65 × 106, and thus giving a total investment cost of about 4.15 × 106. On the other hand, annual O&M cost without PTU was calculated ca. 300,000/year [12]. If investment cost for PTU is assumed as 25% of total investment cost (for PE = 200,000 plant) and if it is assumed that O&M cost (for PE = 200,000 plant) would increase by 20% by the addition of PTU, annual total cost is calculated as 4.82/PE·yr for the proposed biomethanization plant (PE = 100,000). Cost estimation results are summarized in Table 2, and change in annual cost values for the plants serving 100,000–1,000,000 PE is presented in Figure 2. Consequently, when compared with the annual energy savings (4.48/PE·yr), almost 93% of annual total cost (4.82/PE·year) can be recovered from the proposed integrated biomethanization plant (for PE = 100,000; XPS = 61 g/PE·day;  g/PE·day) in the case of implementing 100% renewable energy subsidy with a payback period of 13.2 years.

Unfortunately, integrated biomethanization plants would not be much feasible without public subsidy at the current situation. Subsidies have undeniable effect on the improvement of renewable energy production. It is considered that energy subsidies not only cover operating costs of companies but also encourage access to the modern energy sources and help to reduce energy import dependency especially in developing countries such as Turkey. The gate fee (or tipping fee) for MSW disposal also has significant effect on the decrease of the payback period although no subsidy is implemented for energy. Municipalities currently pay approximately 15 Euro/tonne landfill gate fee for the MSW and municipal sludge in Turkey. However, this fee needs to be increased in order to meet EU limitations. Comparative costs of landfill in different EU Member States have indicated that gate fee values might fluctuate in the range of 6–220 Euro per tonne of waste excluding tax [13]. Regarding the proposed biomethanization plant, if approximately 40 Euro gate fee is assumed per tonne of waste, the payback period is calculated to be 3.2 years in the case of only gate fee implementation. However, if public subsidy (as 100%) is also implemented together with this gate fee, the payback period will shorten to 2.6 years indicating the positive effects of the incentives on system feasibility.

5. Utilization of Biogas as Transport Fuel

There are different ways of using the produced biogas from the biomethanization plants. These are (i) direct steam generation, (ii) direct combustion, for example, by internal combustion engines (ICE), (iii) simultaneous electricity and useful heat generation, that is, cogeneration at combined heat and power (CHP) plants, (iv) pumping into central natural gas grid after pretreatment, and (v) usage for powering vehicles after pretreatment. Typical fuel value is reported to be 22,400 kJ per 1 m3 normal biogas. Biogas can be used either for the production of heat only or for the generation of electric power. When current is obtained, normally heat is produced in parallel by the combined heat and power (CHP) generation plants. Here, biogas is converted to electricity using on-site power generation equipment at which heat is recovered in the form of hot water or steam for heating applications [1]. Although boilers and other direct combustion applications are by far the cheapest and easiest use options for energy utilization, CHP is one of the most common forms of energy recycling. Turkey has a wide-spread natural gas grid typically used as domestic and industrial power sources, and biogas generated from anaerobic digestion of wastes can also be distributed via this network for community use. However, it was reported that using biogas to power vehicles had the lowest carbon footprint, followed by the use of biogas on-site in a CHP plant. Pumping gas into the grid was the next most efficient [14]. Due to increased use of fossil fuels, atmospheric carbon dioxide which hastens the global warming crisis has also increased [2]. The EU Directive on the promotion of the use of energy from renewable sources sets ambitious targets for all Member States, such that the EU will reach a 20% share of energy from renewable sources by 2020 and a 10% share of renewable energy specifically in the transport sector [15]. Besides, key goals of the “An EU Strategy for Biofuels” is to promote the use of biofuel in transport with the aim of reducing the environmental impact of fossil fuels to define a minimum share of biofuel to be sold on the market of each Member State by 2010 [16]. Thus, use of biogas produced from the wastes as the fuel (gasoline and/or diesel) for transport has increased extensively in recent years. By this way, significant decreases in air emissions from the vehicles and noise pollution would be achieved, dependency on other countries to supply petroleum would cease, biogas wastage at the treatment plants via gas flares would be prevented, and a new income source as well as economic benefit would be provided. It was reported that biogas has been used as vehicle fuel in around 14 cities in Europe, among them the leading two countries are Sweden and Switzerland. For example, in Stockholm, the annual biogas production of about 1.5 × 106 m3 could power about 425 automobiles and 3 trucks, which was obtained from the municipal WWTP serving 600,000 PE [4, 17, 18]. However, some modifications are required on the vehicle and engine technologies. For example, gasoline and diesel vehicles need to be retrofitted for natural gas unless new vehicles are used. Biofuels need to be processed to consistent standards for optimal performance in ICE. Optimization of vehicles includes fine-tuning control systems and engine designs to run on varying blends for maximum fuel efficiency and minimum emissions across the full range of potential blend mixes. Since the Member States of EU must ensure that the minimum share of biofuels sold on their markets is 2% by 31 December 2005 at the latest, and 5.75% by December 2010, most of the automobile industries guarantee its usage safely [16, 19]. Biogas should also comply some quality standards in order to be used as the fuel for transport purposes. Not only does biogas consist mainly of methane and CO2, but it also contains several impurities [1]. It was reported that biogas has to be upgraded to natural gas quality for use in vehicles designed to function on natural gas. This calls for removal of particulates, carbon dioxide, hydrogen sulfide, moisture, and any other contaminants present in the gas to increase the methane content to over 95% (by volume). The carbon dioxide present in biogas dilutes the fuel value of the gas and has to be removed. Hydrogen sulfide can increase corrosion in the presence of water and moisture can cause clogging at lower temperatures. For this purpose, the biogas should be purified by a suitable method, for example, by water scrubbing. [4]. Then this purified biogas can be stored under 200–250 bar pressure at biogas stations and can be sold afterwards. Since clean biogas has the same characteristics as natural gas, the existing natural gas infrastructure can support the use of biogas. Generally biogas is mixed with natural gas, and blending with natural gas can also enhance the distribution of biogas even at relatively small quantities. Moreover, CO2, NOx, and particulate emissions are reported at much lower rates compared to other fuel types; for example, CO, hydrocarbon, NOx, CO2, and particulate emissions from heavy good vehicles powered by biogas are almost 2.5-, 1.14-, 0.6-, 5-, and 7-folds lower than the heavy good vehicles powered by diesel, respectively. It is also reported that benzene (which is a known human carcinogen) emissions are eliminated [4]. Tilche and Galatola [20] reported that the use of biomethane, in particular as biofuel, has been shown to be able to produce large greenhouse gas savings. Methane amounts for the proposed integrated biomethanization plant (at 35°C and 1 atm) were calculated as 2220 m3/day ( g TS/PE·day) and 2980 m3/day ( g TS/PE·day). CH4-enriched biogas (95% CH4) equivalents of the above values can be calculated as 2340 and 3140 m3/day, respectively. Since 1 m3 enriched biogas replaces about 0.8 L of diesel or 1.0 L of gasoline according to Table 3, annual amounts in diesel or gasoline substitutes are about 615,636 or 775,880 L, respectively, for 2340 m3/day CH4-enriched biogas. Moreover, results showed that about 26 or 549 ( g TS/PE·day) and 35 or 737 ( g TS/PE·day) heavy good vehicles and cars could be powered by the produced biogas from the proposed integrated biomethanization plant (PE = 100,000) instead of diesel or gasoline, respectively. The production cost and the selling price of 1 m3 biogas are reported in the ranges of 0.2–0.75 and 0.66–1.1, respectively [17]. Transport fuel susbstituted values determined for the proposed biomethanization plant are summarized in Table 3.

6. Conclusion

The significance of renewable alternative fuels has increased in the last decade due to dwindling supplies of conventional energy sources and rising oil prices. Since natural gas and electricity costs have been increasing day by day, the share of renewable energy in total global energy consumption increases and energy recovery from biogas becomes attractive. Biogas is reported as one of the most important renewable energy sources, and biogas production is mainly based on anaerobic digestion of organic wastes. Turkey’s oil import bills likely to grow and put increasing pressure on the economy. Turkey has the highest gasoline and diesel prices in the world, and there is a high motivation and public acceptance in alternative and relatively cheaper fuels. Only about 0.2% of current energy power in Turkey is obtained from biogas and solid wastes. Since the current energy production is heavily dependant on the imported natural gas and coal in Turkey, renewable energy recovery by anaerobic digestion of organic wastes (biomethanization) has been gaining vital importance in recent years. Towards the EU membership of Turkey, waste minimization and recovery strategy will be based on this approach especially in metropolitan cities. Codigestion of OFMSW with other cosubstrates is reported as an attractive alternative for sustainable management of different separate waste streams produced at large amounts. Although, the most appropriate cosubstrate alternatives for codigestion with OFMSW are reported as the sewage sludge, animal slurries, garden wastes, fruit wastes, and so forth, they may be also used as alternative feedstocks. In this study, an integrated biomethanization plant is proposed at which primary sludge is codigested with SS-OFMSW (mixed wastes originating from the restaurants and canteens and from the greengrocery parts of the supermarkets). Results of this study indicated that almost 93% of annual total cost can be recovered if 100% renewable energy subsidy is implemented with a payback period of 13.2 years. However, if approximately 40 Euro gate fee is also implemented per tonne of waste with public subsidy, the payback period would shorten to 2.6 years indicating the positive effects of the incentives on system feasibility. Since landfilling is still the main solid waste disposal method in Turkey, other benefits of the proposed biomethanization plant would be the reduction of landfill volume requirement and the protection of the groundwater.

In accordance with the EU, the authoritatives in Turkey are aware of that serious precautions should be taken in terms of sustainable environmental protection such as usage of alternative fuels for transport. For example, urban air pollution is often a key driver of alternative fuels for transport in developing countries due to its magnitude and visibility and the degree of public exposure to the problem. In this scope, if transport fuel substitute of the produced biogas is calculated, about 26 heavy good vehicles using diesel or 549 cars using gasoline may be powered per year (PE = 100,000; XPS = 61 g TS/PE·day;  g TS/PE·day). The number of heavy good vehicles or cars might increase up to 35 or 737 in the case of  g TS/PE·day. However, the biogas has to be upgraded for use in vehicles, and some modifications are required on the vehicle and engine technologies.

It is known for certain that number of such proposed biogas plants will increase in Turkey following the government incentive to promote their installations. However, the related regulations regarding energy productivity, environment, Kyoto agreements, clean ecoproduction, and renewable energy should be immediately completed with the supply of the required infrastructure for investment.

Acknowledgment

The authors gratefully acknowledge The Scientific and Technological Research Council of Turkey (TUBITAK) (Project no. 105G024) for the financial support.