Development of Composite Scaffolds for Load-Bearing Segmental Bone Defects

Pilia, Marcello; Guda, Teja; Appleford, Mark

doi:https://doi.org/10.1155/2013/458253

BioMed Research International

On this page

Abstract Introduction References Copyright Related Articles

Review Article | Open Access

Volume 2013 | Article ID 458253 | https://doi.org/10.1155/2013/458253

Development of Composite Scaffolds for Load-Bearing Segmental Bone Defects

Marcello Pilia,¹Teja Guda,¹and Mark Appleford¹

Academic Editor: Aijun Wang

Received01 May 2013

Accepted02 Jul 2013

Published29 Jul 2013

Abstract

The need for a suitable tissue-engineered scaffold that can be used to heal load-bearing segmental bone defects (SBDs) is both immediate and increasing. During the past 30 years, various ceramic and polymer scaffolds have been investigated for this application. More recently, while composite scaffolds built using a combination of ceramics and polymeric materials are being investigated in a greater number, very few products have progressed from laboratory benchtop studies to preclinical testing in animals. This review is based on an exhaustive literature search of various composite scaffolds designed to serve as bone regenerative therapies. We analyzed the benefits and drawbacks of different composite scaffold manufacturing techniques, the properties of commonly used ceramics and polymers, and the properties of currently investigated synthetic composite grafts. To follow, a comprehensive review of in vivo models used to test composite scaffolds in SBDs is detailed to serve as a guide to design appropriate translational studies and to identify the challenges that need to be overcome in scaffold design for successful translation. This includes selecting the animal type, determining the anatomical location within the animals, choosing the correct study duration, and finally, an overview of scaffold performance assessment.

1. Introduction

Orthopedic injuries have been a major area of concern in medicine. In the late 1990s, it was estimated that 7 million fractures occurred each year in the United States alone [1, 2] and that the total medical costs associated with all musculoskeletal conditions added up to nearly $215 billion/year [1–3]. About 800,000 bone grafting procedures conducted annually in the US contributed to these costs [4]. Currently, the bone fractures due to trauma-related injuries account for more than 1.3 million procedures in the United States alone [5, 6]. The aging of the US population as well as the increase in both frequency and severity [7] of these injuries among the elderly has resulted in a significant increase of orthopedic needs and is expected to increase in the near future [1, 4, 8–10]. In the military field, the combat wars in Afghanistan and Iraq have increased the number of trauma procedures performed on a daily basis [11]. These conflicts demonstrated the highest number of debilitating extremity wounds (54%) [11]. Indeed, out of more than 40,000 injuries and casualties sustained in these 2 wars, 82% of them resulted in at least one musculoskeletal extremity wound [12]. The extent of these incapacitating injuries includes soft tissue wounds (53%) and fractures (26%), most of which (82%) were severe open fractures [13].

2. Segmental Bone Defects

Natural bone has the ability to repair itself through a very well-studied healing cascade (Table 1). However, in the case of segmental bone defects (SBDs), the body cannot heal on its own, and, therefore, they represent a significant challenge in the orthopedic community. SBDs are defined as injuries in which a section of bone is completely shattered and/or absent. Usually, the size of the missing section is large enough that bone either cannot regenerate on its own (critical sized defects) or results in the formation of pseudoarthrosis (nonunions), malunions, and loss of function, making corrective surgery or additional fixation using metallic fixators a common complication [14–23].

SBDs can be brought on by trauma, disease, and age. Trauma can be related to fractures, sport, and blast injuries. Diseases include bone cancer (osteosarcoma), tumor resection and reconstruction, osteoporosis, osteoarthritis [24], generic infections, congenital deformity corrections [25], pathological degenerative bone destruction, and other degenerative diseases [20, 26, 27]. Table 2 summarizes the most common causes of SBDs and lists the risks associated with leaving these injuries untreated.

2.1. Bone Tissue-Engineered Scaffolds for the Treatment of SBDs

Autologous bone grafting has long been considered the gold standard for treating SBDs, but synthetic alternatives are being increasingly investigated to overcome the problems of limited availability of secondary graft sites and associated donor site morbidity [28]. Within the past two decades, the advent of tissue engineering has brought new ideas and the discovery and/or development of innovative biomaterials for bone tissue engineering purposes [8]. Figure 1 illustrates a critical size defect in which the orthopedic surgeon placed bone cement and all the necessary hardware to hold it in place. The implantation of these tissue-engineered biological constructs, also known as scaffolds, has been a major advancement in the field of orthopedics [22, 29–36]. Before understanding what the ideal bone scaffold requirements are, it is first necessary to determine the material and biological properties of these constructs. A schematic of the relationship between material and biological tissue engineering scaffolds is seen in Figure 2; Tables 3 and 4 describe the ultimate biological and material requirements that a bone tissue-engineered scaffold should possess.

(a)

(b)

(c)

(d)

2.2. Bioceramics for SBD Repair

The inorganic component of bone is a carbonated Calcium Phosphate (CaP). One phase of the CaP ceramic is hydroxyapatite (HAp). Having a chemical formula (Ca₁₀(PO₄)₆(OH)₂), stoichiometric HAp has a structure very similar to that of natural bone [24, 26, 34, 43–45]. For this reason, synthetic CaP materials including HAp are FDA-approved and were among the most investigated materials for scaffold composition for over three decades [46–51]. CaPs differ from one another in origin, composition, morphology, and physicochemical properties. Most CaP ceramic materials are biocompatible, osteoconductive, have a bioactive surface, and can be biodegradable [18, 52], making them very well suited for bone repair, augmentation, or substitution [21, 24, 38, 39, 53]. The osteoconductive properties of CaPs support tissue ingrowth, osteoprogenitor cell growth, and the development of bone formation [54] by promoting the attachment, proliferation, differentiation, and migration of bone cells [18, 26, 39, 49]. Their surfaces also allow for a direct, adherent, and strong bond with the bone tissue that can mediate an exchange of Ca²⁺ and P ions between cell matrix and substrate [55–57]. The structural or chemical aspect of CaP ceramics can be modified. CaP coating on metals enhances osteoconductivity by stimulating rapid bone growth onto its surface [58].

2.3. Current Bioceramics Being Investigated

There are many different types of CaPs currently being investigated for tissue engineering purposes. HAp [23, 44, 46, 51, 59–62] is the most commonly used ceramic biomaterial in orthopedic applications because of its biocompatibility [63–65]. HAp scaffolds stimulate cell attachment, growth, and differentiation [23, 48, 66], even though they degrade at a very slow rate [67]. β-tricalcium phosphate (β-TCP) is the second most widely used CaP ceramic in bioengineering, and its alkaline nature makes it a good candidate for hybrid scaffolds to counteract the acidity resulting from polymer breakdown [8, 27, 46, 62, 68]. β-TCP degrades much faster than HAp and is known for its excellent biocompatibility and osteoconductivity that stimulates the proliferation and differentiation of cells [46]. Because HAp and β-TCP are so well suited for this application, scaffolds composed of a mixture of HAp and β-TCP (biphasic CaP-BCaP) are commonly reported in the literature. This combination is known for its osteoconductivity, bioactivity, biocompatibility, and degradability [38] and has drawn the attention of researchers [46]. BCaP can have a controllable degradation rate [49]. Specific ceramic properties can be found in Table 5.

The other generic classes of ceramic materials commonly used for orthopedic fixation are the bioglasses (BGs) and the CaP cements (CPC). BGs are silicon-based materials that are known for promoting bioactivity, by being able to bond to bone by developing bone-like apatite layers on their surface in vivo [39], promoting osteoblast differentiation, and they have similar degradation properties to HAp and β-TCP [25, 79]. A different material, mesoporous BG (MBG), has been reported to have greater bioactivity than BG alone [63]. Nevertheless, being a ceramic, all BGs are very brittle [39, 63]. CPCs are combinations of soft-form dicalcium phosphate (DCP) and tetracalcium phosphate (TTCP) that hardens when the two are combined [45, 80]. An advantage of self-hardening CPC is that it allows surgeons to fill in the gap between the two bone endings and conform to the shape of the defects rather than matching the gap with standard size scaffold [1, 45, 80]. Bone cements are also readily available and do not cause any major issues with either immunogenicity or disease transmission [20]. However, this material lacks a 3-dimensional porous structure and does not support bone growth well [20].

2.4. Polymer Properties

Polymeric materials are classified as natural and synthetic polymers. The former are further divided into proteins and polysaccharides. Natural polymers have weak mechanical properties but have hydrophilic surfaces that favor cell attachment and differentiation. Silk fibroin, collagen, and chitosan belong to this family. Silk is known for its biocompatibility, mechanical properties, ability to be handled in many different ways, and has relatively slow degradation rates [63]. Interconnected porosity can be achieved when the silk is prepared with organic solvent and salt leeching [66]. Collagen-I (Col-I) is the organic component of bone ECM. This makes it biocompatible and biodegradable [60], yet it lacks compressive mechanical strength and stiffness [59]. Col-I is sometimes associated with immunogenic responses from the host as well as pathogen transmission. However, the major problems associated with collagen are its cost, solubility, and lack of commercial sources [62]. Gelatin collagen is the denatured version of collagen and does not have the same drawbacks as the naturally occurring counterpart [62]. It is inexpensive, widely available, and mass producible [62]. Chitosan, a partial derivative of chitin, has received much attention because of its excellent biocompatibility and biodegradability [23]. It is only soluble at acidic pH (usually below 6.0), and when degraded it breaks down into nontoxic compounds [81].

In contrast, synthetic biodegradable polymers, such as polylactic acid (PLA), polyglycolic acid (PGA), or poly(lactic-co-glycolic acid) (PLGA), have a common disadvantage of possessing a hydrophobic surface that does not facilitate cell attachment after cell seeding [46, 63, 64]. However, these biodegradable polymers have attracted significant attention from the scientific community because of the ease with which these materials can be fabricated and because of their relative high elasticity. In general, polymers and organic scaffolds can be shaped into many different structures, creating a well suited architecture. In doing so, the mechanical properties of the material are usually lost, often resulting in very low or no compressive strength [62, 66]. These polymeric materials (PLA, PGA and PLGA) have been used as temporary extracellular matrices in bone tissue-engineering scaffolds [64] as well as sutures, thereby providing evidence of safety [27]. Nonetheless, before PLGA polymers are metabolized into their final product, they can release byproducts such as lactic acid and glycolic acid. Being acidic, these byproducts are known to cause bacteria-free inflammation or a foreign body reaction [68, 82]. There are however ways to neutralize these acids. One such way is by adding CaP ceramics, an alkaline material, to the polymeric scaffold [68]. One other disadvantage for using the PLA, PGA, or PLGA is their degradation rates. Although it has been reported that degradation of these polymers can be adjusted in the laboratory by influencing molecular mass, comonomer ratios, specimen size, configuration, and environmental conditions [8], degradation in vivo is difficult to control and remains among the major disadvantages for the use of these polymers [44].

Polycaprolactone (PCL) has been shown to have good mechanical properties and have fully interconnected pores that increase biocompatibility in vitro [5, 6, 38]. PCL also has a slower degradation rate than other polymers [38, 39], exists in an elastic state at room temperature, and has a low melting point of 60°, making it a good candidate for fabrication using fused deposition modeling [83]. Moreover, when implanted, PCL scaffolds do not interfere with imaging techniques [6]. However, PCL’s surface is still hydrophobic and presents low affinity towards cellular attachment. This makes it necessary to find a surface modification technique to make the surface more osteoconductive [83]. Regardless, the mechanical properties of these polymeric materials alone are not similar to those of native bone [44]. PU has been shown to be polymerized in a specific manner that favors biocompatibility with human cells and tissues. It has also been shown to have adequate mechanical properties due to its hydrogen bonds within the macroparticles that hold the structure together. However, after Pierschbacher and Ruoslahti found the protein sequence needed for the cell to attach to the surface [84], cell attachment and affinity increased [82].

3. Hybrid Bone Scaffolds

Even though there are many advantages to CaPs, the drawbacks are significant and include mechanical instability, difficulty at shaping and forming them into a specific architecture, their long degradation rate, and possible bioactivity issues. The greatest concern with HAp specifically, and with ceramics in general, is that they cannot be used alone for load-bearing applications due to the brittleness (failure due to lack of plastic deformation) of these materials and the overall poor mechanical properties [20, 21, 23, 24, 26, 38, 39, 44, 59, 61, 63, 65–67, 76, 80, 85, 86]. In addition, CaP ceramics degrade very slowly [23, 26, 60, 85, 87, 88]. In contrast, fast CaP degradation is also not necessarily beneficial for tissue regeneration. It is known that β-TCP degrades at a much faster rate than HAp. However, faster degradation often equates to a higher level of Ca²⁺ being released, and any localized Ca²⁺ released higher than 10 mMol [89] is detrimental, including being cytotoxic at the site. It is also known that the sintering process makes CaP ceramics stronger, but compromises the surface bioactivity of the scaffold due to the overall increase in crystal size and crystallinity [38]. It has been reported that β-TCP is mechanically weaker than HAp and when released, the body cannot break it down into CaP, preventing strong bonding between the scaffold and the newly secreted bone [88]. In addition some researchers believe that CaPs are difficult to process [65] and are not porous enough [66]. Moreover, since it is difficult to shape sintered scaffolds as a result of their brittleness, surgeons are often forced to create an incision in the injured bone to match the scaffold when using ceramic scaffolds, thereby leading to more bone loss, trauma, and increased surgical time [1]. CPCs also cannot be used in load-bearing applications because of their low mechanical strength and lack of porous architecture that make it difficult to integrate with adjacent bones.

By developing a hybrid scaffold composed of CaP and other polymeric materials, researchers believe that the original structure of bone could be recreated by taking advantage of the CaP’s osteoconductivity as well as eliminating the brittleness of the scaffold. The combination of the osteoconductivity and the strength of CaP, in conjunction with the good workability and elasticity of biopolymers, makes hybrid composite scaffolds very good candidates for bone tissue engineering [27, 61, 66]. Hybrid scaffolds are currently being studied and developed to try to simulate the organic (Col-I) and the inorganic (HAp) portion of natural bone [44, 65]. Hybrid scaffolds consist of polymeric matrices that are paired with ceramics [79]. However, there is a wide range of polymeric materials with different properties available (Table 6). Currently, the challenge in developing a tissue-engineered scaffold with ideal properties is to find a way to combine these completely different materials together, while maintaining a porous architecture and adequate mechanical properties that favor bone formation. Even though material selection for the scaffold has a direct impact on the biological and physical properties of the construct, there are some factors contributing to the low mechanical properties that are not related to the material used. The more porous the architecture of the scaffold is, the weaker its compression strength becomes.

3.1. Properties of Currently Investigated Hybrid Scaffolds

Scaffold fabrication techniques currently used include casting and particulate leaching [5, 46, 82, 90–92], gas foaming [5, 90], freeze drying [5, 25, 59, 90], electrospinning [9, 51, 90], thermally induced phase separation (TIPS) [5, 65, 90, 91], microsphere sintering [90], supercritical CO₂ technology [93], fused deposition modeling (FDM) [5, 6], 3D printing [5], in situ precipitation [61], thermally induced phase inversion [44], selective laser sintering [40], low temperature deposition manufacturing (LDM) [68] ceramic or polymeric coating with either polymers or ceramic slurry, respectively [27], solid-liquid phase separation (SLPS) [39], and a combination of these [8, 77].

As mentioned previously, mechanical strength is considered one of the most important properties and requirements of load-bearing scaffolds. When designing a bone scaffold for tissue engineering, its mechanical properties should match that of natural bone. However, only a small percentage of investigated scaffolds in the literature are being tested for mechanical properties. Of the scaffolds-tested compression strength and/or bending and elastic modulus strength were usually investigated. However, in bone, failure due to compression is very rarely seen; most fractures are due to torsion or bending forces [94]. In contrast, the elastic modulus property determines the slope of the stress-strain curve. Ceramics have been reported to have high elastic modulus and low ductility, whereas polymers, on the contrary, have lower hardness and modulus.

Although the concept of hybrid bone scaffold is a relatively new one, the literature has already been inundated with journal articles describing the technique and the properties of such scaffolds. A wide range of scaffolds with different properties can be found in the literature. It has been demonstrated that hybrid designs increase the overall mechanical properties of the existing scaffolds. There was a wide range of scaffolds fabricated and mechanically tested to determine their similarities to natural trabecular bone. Some implants exhibited very low compressive strength properties, 2–12 MPa, which correlate with the natural compressive strength of trabecular bone [23, 38, 61, 64, 77, 79, 86, 95]. These scaffolds should be considered for non-load-bearing applications because they also exhibited lower modulus values (up to 25 MPa), which are well below the natural range of trabecular bone (50–500 MPa). These scaffolds were generally very porous with ranges between 80, and 87%, which is essential for bone ingrowth.

Scaffolds investigated for load-bearing applications generally had a compressive strength that ranged between 1 and 80 MPa [6, 21, 27, 44, 90, 91]. However, these samples with higher compression strength had porosities lower than 70%. The scaffold with the highest compression strength was investigated by Zhang et al. using an in situ precipitation technique. This HAp/PLLA composite scaffold reported compression values of 110–155 MPa [61], although no information was provided on the porosity/pore size. Nevertheless, the lack of scaffold characterization for porosity or pore size renders inconclusive whether this scaffold has tissue regenerative properties. Overall, scaffolds with lower compressive strength and modulus had a higher porosity which helped with bone growth, but scaffolds with a higher compressive strength needed for stabilization of SBDs had a lower porosity.

4. In Vivo Load-Bearing Application Techniques

With many different in vivo animal studies used to investigate bone regeneration, deciding on the appropriate model and application can be challenging. First, researchers need to determine an appropriate animal model to recreate an SBD large enough that cannot self-heal. Then, proper anatomical location of the investigated scaffold in the animal should be decided, in order to recreate active loading on to the construct. At this point, an estimate length of study to see perceptible results should be determined as well as valid control groups and an adequate analysis technique.

To date, only a few hybrid design scaffolds have been investigated in vivo. However, the literature is overwhelmed with the in vivo investigations of ceramic scaffolds [96]. This is because the concept of hybrid composite scaffolds is still relatively new, and to date, insufficient animal validation testing has been performed. Table 7 shows the summary of the reviewed studies and differentiates them between animal choice, anatomical location, length of study, control, and analysis of results.

4.1. Animal Choice

With many different animals used for research, choosing an adequate model platform for the scaffolds is essential. The most important consideration is that the animal chosen should have anatomical, physiological, and pathophysiological analogies with humans. Previous models that have been used in the field vary in size. They include mice, rats, rabbits, dogs, sheep, and pigs. Once the similarities with humans are determined, it is important to keep in consideration the ability to physically provide care for many animals both during and after the testing. Other factors to keep in mind, yet not as critical, are the costs of acquisition and maintenance of the animals versus statistical size, tolerance to captivity, and ease of housing [97]. Mice and rats are used to test basic cytotoxic properties of the scaffolds, and also they are used to implant scaffolds subdermally to initiate vascularization within the construct or test osteogenicity away from an existing bone source. These are the smallest animals on which bone regeneration is tested. Rabbits, also a small animal species, show easier, faster, and more consistent bone healing. Unfortunately, this model is limited by the size and maturity of the bones and the weight of the animals [98]. Dogs have similar bone density to humans but have a series of disadvantages. Canines have faster solid bony fusion than humans, low nonunion rates, high variation between breeds, and negative perception from the public. Sheep are also very similar to humans in body weight and bone dimensions (especially long bones). The drawback is age-dependent remodeling of bone around 7 to 9 years of age. The pig is the largest animal model used for SBD regeneration. They have a very similar bone density, anatomy, and microstructure to humans. The main drawbacks, especially in load-bearing scaffolds, are that the animals are extremely large and heavy and have an accelerated rate of bone growth, which makes it difficult to differentiate between early and late remodeling [97].

Of the studies reviewed, the animal that was most often chosen was the rat [25, 46, 72, 77, 78]. Other studies also used rabbits [73, 76] and sheep [75]. Since hybrid scaffolds are still a relatively new concept in the bone regenerative field, it is understandable why researchers chose to test the construct on a small animal first to determine initial performance and change it accordingly. It is foreseen that this area of research will yield noticeable results in the near future to help fill the knowledge gap.

4.2. Anatomical Choice for Load-Bearing SBDs

Once the animal model is chosen, the next step requires determining an appropriate surgical site that will accurately test the behavior of the bone scaffold in vivo. For load-bearing applications, it is necessary to use a limb or vertebral bone. This criterion allows focusing on the following bone choices: the femur or the tibia in the hind leg and the ulna/radius or humerus in the fore leg, in addition to the lumbar vertebrae. In most of the studies reviewed, the femur was the preferred anatomical choice [25, 46, 72, 73, 76–78]. However, in the only large animal model reviewed (the sheep), the tibia was chosen with a triangular defect on the medial tibia plateau [75]. The femur is the largest long bone in most animals. Since humans stand up right, the femur directly supports the body’s entire load, but in animals that use four limbs for stabilization, both the humerus and the femur distribute the animal’s weight. Because of these characteristics, the femur is preferred for testing load-bearing SBD model.

After choosing the animal and the bone to test, the specific location is selected. One model involves creating a midshaft defect and placing a matching size scaffold within it [72, 78]. This model requires fixation devices to be implanted around the surgical site to maintain the two endings of the scaffold from crushing the scaffold and from moving. This model tests the mechanical properties of the scaffold and the ability to regenerate large amounts of bone. Also, this surgical site most closely resembles what occurs in clinical practice, as it gives an accurate representation of how well the scaffold will perform in a segmental setting. Extremity injuries from trauma affect all of the bone, not just parts of it. Another model involves creating only a partial defect. This is the case of rabbit radius/ulna, where only the radius is removed and the scaffold is placed next to the ulna [74]. This model might avoid the requirement of utilizing fixation devices to stabilize the animal; however, in the rabbit, this model is not truly weight bearing.

A third model involves drilling longitudinally through the cortical bone into the cancellous bone at the medial epicondyles of femur [25, 46, 76, 77]. The advantages of the medial epicondyle of the femur model is that no surgical fixation devices are required, and since the defects span both the cortical and the trabecular bone, histological evaluation ex vivo can determine how the bone regenerated and whether remodeling occurred. However, if the scaffold being investigated is made to be loaded unidirectionally; then, this model will likely fail in vivo. When implanted in the epicondyle, the scaffold is exposed mostly to circumferential forces, and, therefore, will sustain damages before it can regenerate. Overall, this model is load protected and is seen more as a non-load-bearing model. Thus, based on the scaffold properties and architecture, the femur epicondyle might not be the best anatomical choice for this application.

4.3. Length of Study—Modeling versus Remodeling

The reviewed in vivo studies were analyzed for as little as 2 weeks [77] and for as long as 48 weeks [76]. When selecting the length of study for the in vivo study, there are times during which different stages of healing occur depending on the animal model which was utilized for the study. While animal models do have species-dependent bone formation rates, typically, the first 4 weeks of most animal studies are used to assess the host’s response to the implant (biocompatibility). The first two months are then used for assessment of healing (modeling). Anything beyond that will be testing the remodeling process, during which the newly healed bone will gain strength. Of the reviewed studies, two rat femur models were investigated for less than 4 weeks [77, 78]. This step is of critical importance for hybrid biomaterials, since they have a high risk of causing acute inflammatory reactions depending on what polymeric material was used when constructing the scaffolds. Two other studies reviewed were performed for 1 to 2 months to assess bone healing (modeling) [25, 75], and 4 other studies instead investigated long-term remodeling of bone [46, 72, 73, 76]. Perhaps if the researcher has early in vitro data showing biocompatibility of the scaffold, the animal study will have different time intervals that demonstrate the healing process through early response, modeling, and remodeling processes.

4.4. Analysis of the SBD Models

After developing, characterizing, and implanting the scaffold in an animal, the test subjects are sacrificed so that the ability to regenerate bone can be assessed. There are a number of techniques used by researchers to investigate bone growth: histology, microcomputed tomography (μ-CT) analysis and bone density scans. Load-bearing scaffolds should also be investigated for their ability to gain strength while implanted. This is accomplished through the use of mechanical testing. Using histology, the tissue where the bone scaffold was implanted is processed and stained on thin sections that can be observed by microscopy.

Most researchers use histology (either decalcified or undecalcified) to analyze new bone volume, new soft tissue formation, and area of scaffold resorbed. In hybrid scaffolds, the foreign body reaction should also be analyzed. The other common characterization performed on explanted tissues is μ-CT. This technique isused to analyze new bone formation, regeneration patterns, and bone density. However, because μ-CT reconstructions are very subjective to the operator, there is always the need for histology to support the data. The last test that should be required after investigating a load-bearing scaffold is mechanical analysis of the construct postimplantation. The excised tissues should be tested for ultimate compression, tensile strength, and elastic modulus. Surprisingly, only two long-term studies performed mechanical analysis of the defect after the sacrifice of the animals. Without this test, it is difficult to determine whether the implant was successful at recreating a load-bearing structure.

When analyzing the performance of the scaffold, it is usually compared to positive and negative controls and preferably both. In hybrid scaffolds, a control is usually the ceramic or polymer alone and often an autograft from the same donor. It has been previously shown that there is no need to compare scaffold performance to a defect-only control since it has been shown repeatedly that an empty critical-sized defect does not heal on its own [72].

5. Summary and Perspectives

The clinical issues surrounding the treatment of load-bearing SBDs need a multipronged approach for treatment. Current strategies focus on a combination of osteoconductive substrates delivering osteoinductive growth factors and osteogenic cell sources. This review focuses on the development of composite hybrid scaffolds composed of ceramic and polymeric materials that provide the mechanical stability, structure, and calcium source required to serve as a suitable osteoconductive surface in healing SBDs. This information can be used to develop and implement in vivo testing of the investigated implants by selecting the appropriate animal model, the most accurate anatomical positioning in the bone, determining the length of the study, and finally the analysis of the samples.

Clearly, there is a need for a hybrid scaffold technology with the strength of the ceramics and the elasticity of polymers that will move the field closer to a functional load-bearing scaffold. When developing the scaffolds, it is important to take into consideration the requirements of scaffolds as well as the drawbacks of the materials being used, so that the researcher can then test accordingly. This includes testing for cytotoxicity and mechanical properties. Moreover, when investigating a load-bearing scaffold, the experimental mechanical properties should always be reported. The true difference between a bone scaffold and the load-bearing scaffold resides in the mechanical properties. Surprisingly, this was not the trend seen in the literature, where many load-bearing scaffolds should have been considered safe to handle, but not to load. There are many journal articles that investigate in vitro hybrid bone scaffolds, but very few have moved on to in vivo testing. Of those few, the majority have used small animal models. It is expected that as more suitable composite scaffolds perform well in vitro, in vivo characterization will significantly increase.

After years of focusing on purely ceramic or purely polymeric scaffolds, researchers have started to consider hybrids, and despite the fact they have high potential, the field is still far from having a scaffold that can be fully loaded that supports viable bone regeneration in a reasonable time after the implant. In the best case scenario, these revolutionary scaffolds would eliminate the need of fixation devices or at least they could minimize their need. They could also be used to deliver growth factors to accelerate healing from the scaffold surface and to deliver appropriate stem cells into the wound environment to tackle critical-sized defects. The overall cost of surgeries would decrease, the healing time would be decreased significantly, and there would not be a need for multiple revision surgeries once these technologies are optimized.

Acknowledgment

This paper was prepared as a part of M. Pilia’s doctoral dissertation work.

References

H. H. K. Xu, M. D. Weir, and C. G. Simon, “Injectable and strong nano-apatite scaffolds for cell/growth factor delivery and bone regeneration,” Dental Materials, vol. 24, no. 9, pp. 1212–1222, 2008.
View at: Publisher Site | Google Scholar
A. Praemer, S. Furner, and D. P. Rice, Musculoskeletal Conditions in the United Statesed, American Academy of Orthopaedic Surgeons, Park Ridge, Ill, USA, 1st edition, 1999.
A. M. Ambrosio, J. S. Sahota, Y. Khan, and C. T. Laurencin, “A novel amorphous calcium phosphate polymer ceramic for bone repair: I. Synthesis and characterization,” Journal of Biomedical Materials Research, vol. 58, pp. 295–301, 2001.
View at: Google Scholar
C. T. Laurencin, A. M. A. Ambrosio, M. D. Borden, and J. A. Cooper Jr., “Tissue engineering: orthopedic applications,” Annual Review of Biomedical Engineering, no. 1, pp. 19–46, 1999.
View at: Google Scholar
H. Chim, D. W. Hutmacher, A. M. Chou et al., “A comparative analysis of scaffold material modifications for load-bearing applications in bone tissue engineering,” International Journal of Oral and Maxillofacial Surgery, vol. 35, no. 10, pp. 928–934, 2006.
View at: Publisher Site | Google Scholar
I. Gibson, M. M. Savalani, C. X. Lam et al., “Towards a medium/high load-bearing scaffold fabrication system,” Tsinghua Science and Technology, vol. 14, supplement 1, pp. 13–19, 2009.
View at: Publisher Site | Google Scholar
Y. H. An, Internal Fixation in Osteoporotic Bone, Thieme Medical, New York, NY, USA, 2002.
Y. Yang, Y. Zhao, G. Tang, H. Li, X. Yuan, and Y. Fan, “In vitro degradation of porous poly(l-lactide-co-glycolide)/β-tricalcium phosphate (PLGA/β-TCP) scaffolds under dynamic and static conditions,” Polymer Degradation and Stability, vol. 93, no. 10, pp. 1838–1845, 2008.
View at: Publisher Site | Google Scholar
F. Yang, J. G. C. Wolke, and J. A. Jansen, “Biomimetic calcium phosphate coating on electrospun poly(ε-caprolactone) scaffolds for bone tissue engineering,” Chemical Engineering Journal, vol. 137, no. 1, pp. 154–161, 2008.
View at: Publisher Site | Google Scholar
L. L. Hench and J. M. Polak, “Third-generation biomedical materials,” Science, vol. 295, no. 5557, pp. 1014–1017, 2002.
View at: Google Scholar
B. D. Owens, J. F. Kragh Jr., J. C. Wenke, J. Macaitis, C. E. Wade, and J. B. Holcomb, “Combat wounds in operation iraqi freedom and operation enduring freedom,” Journal of Trauma, vol. 64, no. 2, pp. 295–299, 2008.
View at: Publisher Site | Google Scholar
D. I. Devore, T. J. Walters, R. J. Christy et al., “For combat wounded: extremity trauma therapies from the USAISR,” Military Medicine, vol. 176, no. 6, pp. 660–663, 2011.
View at: Google Scholar
B. D. Owens, J. F. Kragh Jr., J. Macaitis, S. J. Svoboda, and J. C. Wenke, “Characterization of extremity wounds in operation Iraqi freedom and operation enduring freedom,” Journal of Orthopaedic Trauma, vol. 21, no. 4, pp. 254–257, 2007.
View at: Publisher Site | Google Scholar
J. F. Brandoff, J. S. Silber, and A. R. Vaccaro, “Contemporary alternatives to synthetic bone grafts for spine surgery,” American Journal of Orthopedics, vol. 37, no. 8, pp. 410–414, 2008.
View at: Google Scholar
P. Buma, W. Schreurs, and N. Verdonschot, “Skeletal tissue engineering—from in vitro studies to large animal models,” Biomaterials, vol. 25, no. 9, pp. 1487–1495, 2004.
View at: Publisher Site | Google Scholar
C. M. Cowan, C. Soo, K. Ting, and B. Wu, “Evolving concepts in bone tissue engineering,” Current Topics in Developmental Biology, vol. 66, pp. 239–285, 2005.
View at: Publisher Site | Google Scholar
I. Drosse, E. Volkmer, R. Capanna, P. D. Biase, W. Mutschler, and M. Schieker, “Tissue engineering for bone defect healing: an update on a multi-component approach,” Injury, vol. 39, no. 2, pp. S9–S20, 2008.
View at: Publisher Site | Google Scholar
R. Z. LeGeros, “Properties of osteoconductive biomaterials: calcium phosphates,” Clinical Orthopaedics and Related Research, no. 395, pp. 81–98, 2002.
View at: Google Scholar
A. S. Mistry and A. G. Mikos, “Tissue engineering strategies for bone regeneration,” Advances in Biochemical Engineering/Biotechnology, vol. 94, pp. 1–22, 2005.
View at: Google Scholar
C. Weinand, I. Pomerantseva, C. M. Neville et al., “Hydrogel-β-TCP scaffolds and stem cells for tissue engineering bone,” Bone, vol. 38, no. 4, pp. 555–563, 2006.
View at: Publisher Site | Google Scholar
J. A. Puértolas, J. L. Vadillo, S. Sánchez-Salcedo, A. Nieto, E. Gómez-Barrena, and M. Vallet-Regí, “Compression behaviour of biphasic calcium phosphate and biphasic calcium phosphate-agarose scaffolds for bone regeneration,” Acta Biomaterialia, vol. 7, no. 2, pp. 841–847, 2011.
View at: Publisher Site | Google Scholar
Z. Lu, S.-I. Roohani-Esfahani, G. Wang, and H. Zreiqat, “Bone biomimetic microenvironment induces osteogenic differentiation of adipose tissue-derived mesenchymal stem cells,” Nanomedicine: Nanotechnology, Biology, and Medicine, vol. 8, no. 4, pp. 507–515, 2012.
View at: Publisher Site | Google Scholar
J. Fan, L. Bi, T. Wu et al., “A combined chitosan/nano-size hydroxyapatite system for the controlled release of icariin,” Journal of Materials Science. Materials in Medicine, vol. 23, no. 2, pp. 399–407.
View at: Publisher Site | Google Scholar
F. Baino, E. Verné, and C. Vitale-Brovarone, “3-D high-strength glass-ceramic scaffolds containing fluoroapatite for load-bearing bone portions replacement,” Materials Science and Engineering C, vol. 29, no. 6, pp. 2055–2062, 2009.
View at: Publisher Site | Google Scholar
C. Xu, P. Su, X. Chen et al., “Biocompatibility and osteogenesis of biomimetic Bioglass-Collagen-Phosphatidylserine composite scaffolds for bone tissue engineering,” Biomaterials, vol. 32, no. 4, pp. 1051–1058, 2011.
View at: Publisher Site | Google Scholar
S.-S. Kim, M. Sun Park, O. Jeon, C. Yong Choi, and B.-S. Kim, “Poly(lactide-co-glycolide)/hydroxyapatite composite scaffolds for bone tissue engineering,” Biomaterials, vol. 27, no. 8, pp. 1399–1409, 2006.
View at: Publisher Site | Google Scholar
Y. Kang, A. Scully, D. A. Young et al., “Enhanced mechanical performance and biological evaluation of a PLGA coated β-TCP composite scaffold for load-bearing applications,” European Polymer Journal, vol. 47, no. 8, pp. 1569–1577, 2011.
View at: Publisher Site | Google Scholar
A. Khadka, J. Li, Y. Li, Y. Gao, Y. Zuo, and Y. Ma, “Evaluation of hybrid porous biomimetic nano-hydroxyapatite/polyamide 6 and bone marrow-derived stem cell construct in repair of calvarial critical size defect,” Journal of Craniofacial Surgery, vol. 22, no. 5, pp. 1852–1858, 2011.
View at: Publisher Site | Google Scholar
J. M. Bouler, M. Trecant, J. Delecrin, J. Royer, N. Passuti, and G. Daculsi, “Macroporous biphasic calcium phosphate ceramics: influence of five synthesis parameters on compressive strength,” Journal of Biomedical Materials Research, vol. 32, pp. 603–609, 1996.
View at: Google Scholar
S. Deville, E. Saiz, R. K. Nalla, and A. P. Tomsia, “Freezing as a path to build complex composites,” Science, vol. 311, no. 5760, pp. 515–518, 2006.
View at: Publisher Site | Google Scholar
S. Deville, E. Saiz, and A. P. Tomsia, “Freeze casting of hydroxyapatite scaffolds for bone tissue engineering,” Biomaterials, vol. 27, no. 32, pp. 5480–5489, 2006.
View at: Publisher Site | Google Scholar
U. Gbureck, T. Hölzel, C. J. Doillon, F. A. Müller, and J. E. Barralet, “Direct printing of bioceramic implants with spatially localized angiogenic factors,” Advanced Materials, vol. 19, no. 6, pp. 795–800, 2007.
View at: Publisher Site | Google Scholar
S. H. Li, J. R. De Wijn, P. Layrolle, and K. De Groot, “Synthesis of macroporous hydroxyapatite scaffolds for bone tissue engineering,” Journal of Biomedical Materials Research, vol. 61, no. 1, pp. 109–120, 2002.
View at: Publisher Site | Google Scholar
E. B. Montufar, T. Traykova, C. Gil et al., “Foamed surfactant solution as a template for self-setting injectable hydroxyapatite scaffolds for bone regeneration,” Acta Biomaterialia, vol. 6, no. 3, pp. 876–885, 2010.
View at: Publisher Site | Google Scholar
A. R. Studart, U. T. Gonzenbach, E. Tervoort, and L. J. Gauckler, “Processing routes to macroporous ceramics: a review,” Journal of the American Ceramic Society, vol. 89, no. 6, pp. 1771–1789, 2006.
View at: Publisher Site | Google Scholar
C. Vitale-Brovarone, M. Miola, C. Balagna, and E. Verné, “3D-glass-ceramic scaffolds with antibacterial properties for bone grafting,” Chemical Engineering Journal, vol. 137, no. 1, pp. 129–136, 2008.
View at: Publisher Site | Google Scholar
D. J. Hak, “Management of aseptic tibial nonunion,” Journal of the American Academy of Orthopaedic Surgeons, vol. 19, no. 9, pp. 563–573, 2011.
View at: Google Scholar
S.-I. Roohani-Esfahani, S. Nouri-Khorasani, Z. Lu, R. Appleyard, and H. Zreiqat, “The influence hydroxyapatite nanoparticle shape and size on the properties of biphasic calcium phosphate scaffolds coated with hydroxyapatite-PCL composites,” Biomaterials, vol. 31, no. 21, pp. 5498–5509, 2010.
View at: Publisher Site | Google Scholar
P. Fabbri, V. Cannillo, A. Sola, A. Dorigato, and F. Chiellini, “Highly porous polycaprolactone-45S5 Bioglass scaffolds for bone tissue engineering,” Composites Science and Technology, vol. 70, no. 13, pp. 1869–1878, 2010.
View at: Publisher Site | Google Scholar
K. H. Tan, C. K. Chua, K. F. Leong et al., “Scaffold development using selective laser sintering of polyetheretherketone-hydroxyapatite biocomposite blends,” Biomaterials, vol. 24, no. 18, pp. 3115–3123, 2003.
View at: Publisher Site | Google Scholar
G. A. Helm, H. Dayoub, and J. A. Jane Jr., “Gene-based therapies for the induction of spinal fusion,” Neurosurgical Focus, vol. 10, no. 4, article E5, 2001.
View at: Google Scholar
G. A. Helm, H. Dayoub, and J. A. Jane Jr., “Bone graft substitutes for the promotion of spinal arthrodesis,” Neurosurgical Focus, vol. 10, no. 4, article E4, 2001.
View at: Google Scholar
C. E. Tanase, M. I. Popa, and L. Verestiuc, “Biomimetic bone scaffolds based on chitosan and calcium phosphates,” Materials Letters, vol. 65, no. 11, pp. 1681–1683, 2011.
View at: Publisher Site | Google Scholar
H. Wang, Y. Li, Y. Zuo, J. Li, S. Ma, and L. Cheng, “Biocompatibility and osteogenesis of biomimetic nano-hydroxyapatite/polyamide composite scaffolds for bone tissue engineering,” Biomaterials, vol. 28, no. 22, pp. 3338–3348, 2007.
View at: Publisher Site | Google Scholar
H. H. K. Xu, M. D. Weir, E. F. Burguera, and A. M. Fraser, “Injectable and macroporous calcium phosphate cement scaffold,” Biomaterials, vol. 27, no. 24, pp. 4279–4287, 2006.
View at: Publisher Site | Google Scholar
H. Cao and N. Kuboyama, “A biodegradable porous composite scaffold of PGA/β-TCP for bone tissue engineering,” Bone, vol. 46, no. 2, pp. 386–395, 2010.
View at: Publisher Site | Google Scholar
W. E. Teo, S. Liao, C. Chan, and S. Ramakrishna, “Fabrication and characterization of hierarchically organized nanoparticle-reinforced nanofibrous composite scaffolds,” Acta Biomaterialia, vol. 7, no. 1, pp. 193–202, 2011.
View at: Publisher Site | Google Scholar
K. Zhao, Y.-F. Tang, Y.-S. Qin, and J.-Q. Wei, “Porous hydroxyapatite ceramics by ice templating: freezing characteristics and mechanical properties,” Ceramics International, vol. 37, no. 2, pp. 635–639, 2011.
View at: Publisher Site | Google Scholar
H. R. R. Ramay and M. Zhang, “Biphasic calcium phosphate nanocomposite porous scaffolds for load-bearing bone tissue engineering,” Biomaterials, vol. 25, no. 21, pp. 5171–5180, 2004.
View at: Publisher Site | Google Scholar
E. Bernardo, P. Colombo, I. Cacciotti et al., “Porous wollastonite-hydroxyapatite bioceramics from a preceramic polymer and micro- or nano-sized fillers,” Journal of the European Ceramic Society, vol. 32, no. 2, pp. 399–408, 2012.
View at: Publisher Site | Google Scholar
N. D. Luong, I.-S. Moon, D. S. Lee, Y.-K. Lee, and J.-D. Nam, “Surface modification of poly(l-lactide) electrospun fibers with nanocrystal hydroxyapatite for engineered scaffold applications,” Materials Science and Engineering C, vol. 28, no. 8, pp. 1242–1249, 2008.
View at: Publisher Site | Google Scholar
E. Lerouxel, P. Weiss, B. Giumelli et al., “Injectable calcium phosphate scaffold and bone marrow graft for bone reconstruction in irradiated areas: an experimental study in rats,” Biomaterials, vol. 27, no. 26, pp. 4566–4572, 2006.
View at: Publisher Site | Google Scholar
L. Xiong, D. Xiong, Y. Yang, and J. Jin, “Friction, wear, and tensile properties of vacuum hot pressing crosslinked UHMWPE/nano-HAP composites,” Journal of Biomedical Materials Research B, vol. 98, no. 1, pp. 127–138, 2011.
View at: Publisher Site | Google Scholar
M. R. Urist, “Bone: formation by autoinduction,” Science, vol. 150, no. 3698, pp. 893–899, 1965.
View at: Google Scholar
L. L. Hench, “Bioceramics: from concept to clinic,” Journal of the American Ceramic Society, vol. 74, pp. 1487–1510, 1991.
View at: Google Scholar
L. L. Hench, R. J. Splinter, and W. C. Allen, “Bonding mechanisms at the interface of ceramic prosthetic materials,” Journal of Biomedical Materials Research, vol. 5, no. 6, pp. 117–141, 1972.
View at: Google Scholar
J. F. Osborn and H. Newesely, “The material science of calcium phosphate ceramics,” Biomaterials, vol. 1, no. 2, pp. 108–111, 1980.
View at: Publisher Site | Google Scholar
A. Dey, S. K. Nandi, B. Kundu et al., “Evaluation of hydroxyapatite and β-tri calcium phosphate microplasma spray coated pin intra-medullary for bone repair in a rabbit model,” Ceramics International, vol. 37, no. 4, pp. 1377–1391, 2011.
View at: Publisher Site | Google Scholar
R. J. Kane and R. K. Roeder, “Effects of hydroxyapatite reinforcement on the architecture and mechanical properties of freeze-dried collagen scaffolds,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 7, pp. 41–49, 2012.
View at: Publisher Site | Google Scholar
J. Li, Y. Chen, Y. Yin, F. Yao, and K. Yao, “Modulation of nano-hydroxyapatite size via formation on chitosan-gelatin network film in situ,” Biomaterials, vol. 28, no. 5, pp. 781–790, 2007.
View at: Publisher Site | Google Scholar
C. Y. Zhang, H. Lu, Z. Zhuang, X. P. Wang, and Q. F. Fang, “Nano-hydroxyapatite/poly(L-lactic acid) composite synthesized by a modified in situ precipitation: preparation and properties,” Journal of Materials Science: Materials in Medicine, vol. 21, no. 12, pp. 3077–3083, 2010.
View at: Publisher Site | Google Scholar
L. Bakhtiari, H. R. Rezaie, S. M. Hosseinalipour, and M. A. Shokrgozar, “Investigation of biphasic calcium phosphate/gelatin nanocomposite scaffolds as a bone tissue engineering,” Ceramics International, vol. 36, no. 8, pp. 2421–2426, 2010.
View at: Publisher Site | Google Scholar
C. Wu, Y. Zhang, Y. Zhu, T. Friis, and Y. Xiao, “Structure-property relationships of silk-modified mesoporous bioglass scaffolds,” Biomaterials, vol. 31, no. 13, pp. 3429–3438, 2010.
View at: Publisher Site | Google Scholar
A. Asefnejad, A. Behnamghader, T. M. Khorasani, and B. Farsadzadeh, “Polyurethane/fluor-hydroxyapatite nanocomposite scaffolds for bone tissue engineering. part I: morphological, physical, and mechanical characterization,” International Journal of Nanomedicine, vol. 6, no. 1, pp. 93–100, 2011.
View at: Publisher Site | Google Scholar
G. Wei and P. X. Ma, “Structure and properties of nano-hydroxyapatite/polymer composite scaffolds for bone tissue engineering,” Biomaterials, vol. 25, no. 19, pp. 4749–4757, 2004.
View at: Publisher Site | Google Scholar
S. Bhumiratana, W. L. Grayson, A. Castaneda et al., “Nucleation and growth of mineralized bone matrix on silk-hydroxyapatite composite scaffolds,” Biomaterials, vol. 32, no. 11, pp. 2812–2820, 2011.
View at: Publisher Site | Google Scholar
A. Polini, D. Pisignano, M. Parodi, R. Quarto, and S. Scaglione, “Osteoinduction of human mesenchymal stem cells by bioactive composite scaffolds without supplemental osteogenic growth factors,” PLoS One, vol. 6, no. 10, Article ID e26211, 2011.
View at: Publisher Site | Google Scholar
F. Yang, W. Cui, Z. Xiong, L. Liu, J. Bei, and S. Wang, “Poly(l,l-lactide-co-glycolide)/tricalcium phosphate composite scaffold and its various changes during degradation in vitro,” Polymer Degradation and Stability, vol. 91, no. 12, pp. 3065–3073, 2006.
View at: Publisher Site | Google Scholar
I. H. Kalfas, “Principles of bone healing,” Neurosurgical Focus, vol. 10, no. 4, article E1, 2001.
View at: Google Scholar
C. B. Carter and M. G. Norton, Ceramic Materials: Science and Engineering, Springer, New York, NY, USA, 2007.
K. Rezwan, Q. Z. Chen, J. J. Blaker, and A. R. Boccaccini, “Biodegradable and bioactive porous polymer/inorganic composite scaffolds for bone tissue engineering,” Biomaterials, vol. 27, no. 18, pp. 3413–3431, 2006.
View at: Publisher Site | Google Scholar
T.-M. G. Chu, S. J. Warden, C. H. Turner, and R. L. Stewart, “Segmental bone regeneration using a load-bearing biodegradable carrier of bone morphogenetic protein-2,” Biomaterials, vol. 28, no. 3, pp. 459–467, 2007.
View at: Publisher Site | Google Scholar
F. Jegoux, E. Aguado, R. Cognet et al., “Repairing segmental defect with a composite associating collagen membrane and MBCP combined with total bone marrow graft in irradiated bone defect: an experimental study in rabbit,” Key Engineering Materials, vol. 361-363, pp. 1245–1248, 2008.
View at: Google Scholar
T. Guda, J. A. Walker, B. E. Pollot et al., “In vivo performance of bilayer hydroxyapatite scaffolds for bone tissue regeneration in the rabbit radius,” Journal of Materials Science: Materials in Medicine, vol. 22, no. 3, pp. 647–656, 2011.
View at: Publisher Site | Google Scholar
A. A. Ignatius, O. Betz, P. Augat, and L. E. Claes, “In vivo investigations on composites made of resorbable ceramics and poly(lactide) used as bone graft substitutes,” Journal of Biomedical Materials Research, vol. 58, no. 6, pp. 701–709, 2001.
View at: Publisher Site | Google Scholar
M. Jayabalan, K. T. Shalumon, M. K. Mitha, K. Ganesan, and M. Epple, “Effect of hydroxyapatite on the biodegradation and biomechanical stability of polyester nanocomposites for orthopaedic applications,” Acta Biomaterialia, vol. 6, no. 3, pp. 763–775, 2010.
View at: Publisher Site | Google Scholar
D. Lickorish, L. Guan, and J. E. Davies, “A three-phase, fully resorbable, polyester/calcium phosphate scaffold for bone tissue engineering: evolution of scaffold design,” Biomaterials, vol. 28, no. 8, pp. 1495–1502, 2007.
View at: Publisher Site | Google Scholar
B. Rai, J. L. Lin, Z. X. H. Lim, R. E. Guldberg, D. W. Hutmacher, and S. M. Cool, “Differences between in vitro viability and differentiation and in vivo bone-forming efficacy of human mesenchymal stem cells cultured on PCL-TCP scaffolds,” Biomaterials, vol. 31, no. 31, pp. 7960–7970, 2010.
View at: Publisher Site | Google Scholar
N. Barroca, A. L. Daniel-Da-Silva, P. M. Vilarinho, and M. H. V. Fernandes, “Tailoring the morphology of high molecular weight PLLA scaffolds through bioglass addition,” Acta Biomaterialia, vol. 6, no. 9, pp. 3611–3620, 2010.
View at: Publisher Site | Google Scholar
H. H. K. Xu and C. G. Simon Jr., “Self-hardening calcium phosphate composite scaffold for bone tissue engineering,” Journal of Orthopaedic Research, vol. 22, no. 3, pp. 535–543, 2004.
View at: Publisher Site | Google Scholar
A. Yoshida, T. Miyazaki, E. Ishida, and M. Ashizuka, “Preparation of bioactive chitosan-hydroxyapatite nanocomposites for bone repair through mechanochemical reaction,” Materials Transactions, vol. 45, no. 4, pp. 994–998, 2004.
View at: Publisher Site | Google Scholar
Y. Huang, J. Ren, T. Ren et al., “Bone marrow stromal cells cultured on poly (lactide-co-glycolide)/nano-hydroxyapatite composites with chemical immobilization of Arg-Gly-Asp peptide and preliminary bone regeneration of mandibular defect thereof,” Journal of Biomedical Materials Research A, vol. 95, no. 4, pp. 993–1003, 2010.
View at: Publisher Site | Google Scholar
C. Choong, J. T. Triffitt, and Z. F. Cui, “Polycaprolactone scaffolds for bone tissue engineering: effects of a calcium phosphate coating layer on osteogenic cells,” Food and Bioproducts Processing, vol. 82, no. 2 C, pp. 117–125, 2004.
View at: Publisher Site | Google Scholar
M. D. Pierschbacher and E. Ruoslahti, “Cell attachment activity of fibronectin can be duplicated by small synthetic fragments of the molecule,” Nature, vol. 309, no. 5963, pp. 30–33, 1984.
View at: Google Scholar
J. M. Fernandez, M. S. Molinuevo, M. S. Cortizo, and A. M. Cortizo, “Development of an osteoconductive PCL-PDIPF-hydroxyapatite composite scaffold for bone tissue engineering,” Journal of Tissue Engineering and Regenerative Medicine, vol. 5, no. 6, pp. e126–e135, 2011.
View at: Publisher Site | Google Scholar
S. I. Roohani-Esfahani, Z. F. Lu, J. J. Li, R. Ellis-Behnke, D. L. Kaplan, and H. Zreiqat, “Effect of self-assembled nanofibrous silk/polycaprolactone layer on the osteoconductivity and mechanical properties of biphasic calcium phosphate scaffolds,” Acta Biomaterialia, vol. 8, no. 1, pp. 302–312, 2012.
View at: Publisher Site | Google Scholar
J. Wei, J. Jia, F. Wu et al., “Hierarchically microporous/macroporous scaffold of magnesium-calcium phosphate for bone tissue regeneration,” Biomaterials, vol. 31, no. 6, pp. 1260–1269, 2010.
View at: Publisher Site | Google Scholar
S.-C. Wu, H.-C. Hsu, S.-K. Hsu, W.-H. Wang, and W.-F. Ho, “Preparation and characterization of four different compositions of calcium phosphate scaffolds for bone tissue engineering,” Materials Characterization, vol. 62, no. 5, pp. 526–534, 2011.
View at: Publisher Site | Google Scholar
A. Torcasio, G. H. Van Lenthe, and H. Van Oosterwyck, “The importance of loading frequency, rate and vibration for enhancing bone adaptation and implant osseointegration,” European Cells and Materials, vol. 16, pp. 56–68, 2008.
View at: Google Scholar
S. P. Nukavarapu, S. G. Kumbar, J. L. Brown et al., “Polyphosphazene/nano-hydroxyapatite composite microsphere scaffolds for bone tissue engineering,” Biomacromolecules, vol. 9, no. 7, pp. 1818–1825, 2008.
View at: Publisher Site | Google Scholar
A. Nemati Hayati, H. R. Rezaie, and S. M. Hosseinalipour, “Preparation of poly(3-hydroxybutyrate)/nano-hydroxyapatite composite scaffolds for bone tissue engineering,” Materials Letters, vol. 65, no. 4, pp. 736–739, 2011.
View at: Publisher Site | Google Scholar
S. K. Misra, T. I. Ansari, S. P. Valappil et al., “Poly(3-hydroxybutyrate) multifunctional composite scaffolds for tissue engineering applications,” Biomaterials, vol. 31, no. 10, pp. 2806–2815, 2010.
View at: Publisher Site | Google Scholar
Z.-L. Mou, L.-J. Zhao, Q.-A. Zhang, J. Zhang, and Z.-Q. Zhang, “Preparation of porous PLGA/HA/collagen scaffolds with supercritical CO₂ and application in osteoblast cell culture,” Journal of Supercritical Fluids, vol. 58, no. 3, pp. 398–406, 2011.
View at: Publisher Site | Google Scholar
F. A. M. Pereira, J. J. L. Morais, N. Dourado, M. F. S. F. De Moura, and M. I. R. Dias, “Fracture characterization of bone under mode II loading using the end loaded split test,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 4, no. 8, pp. 1764–1773, 2011.
View at: Publisher Site | Google Scholar
H. Liu, L. Zhang, P. Shi, Q. Zou, Y. Zuo, and Y. Li, “Hydroxyapatite/polyurethane scaffold incorporated with drug-loaded ethyl cellulose microspheres for bone regeneration,” Journal of Biomedical Materials Research B, vol. 95, no. 1, pp. 36–46, 2010.
View at: Publisher Site | Google Scholar
T. Guda, S. Oh, M. R. Appleford, and J. L. Ong, “Bilayer hydroxyapatite scaffolds for maxillofacial bone tissue engineering,” The International Journal of Oral & Maxillofacial Implants, vol. 27, pp. 288–294, 2012.
View at: Google Scholar
J. C. Reichert, S. Saifzadeh, M. E. Wullschleger et al., “The challenge of establishing preclinical models for segmental bone defect research,” Biomaterials, vol. 30, no. 12, pp. 2149–2163, 2009.
View at: Publisher Site | Google Scholar
M. A. K. Liebschner, “Biomechanical considerations of animal models used in tissue engineering of bone,” Biomaterials, vol. 25, no. 9, pp. 1697–1714, 2004.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2013 Marcello Pilia et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

6223

Downloads

2715

Citations