Hydrocolloid-Stabilized Magnetite for Efficient Removal of Radioactive Phosphates

Vellora Thekkae Padil, Vinod; Rouha, Michael; Černík, Miroslav

doi:https://doi.org/10.1155/2014/504760

BioMed Research International

On this page

Abstract Introduction Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2014 | Article ID 504760 | https://doi.org/10.1155/2014/504760

Hydrocolloid-Stabilized Magnetite for Efficient Removal of Radioactive Phosphates

Vinod Vellora Thekkae Padil,¹Michael Rouha,¹and Miroslav Černík¹

Academic Editor: Ismail Kiran

Received06 Sept 2013

Accepted02 Jan 2014

Published18 Feb 2014

Abstract

Liquid radioactive waste is a common by-product when using radioactive isotopes in research and medicine. Efficient remediation of such liquid waste is crucial for increasing safety during the necessary storage of the material. Herein, we present a novel Gum Karaya stabilized magnetite for the efficient removal of radioactive phosphorus ³²P from liquid radioactive waste. This environmentally friendly material is well suited to be used as a nanohydrogel for the removal of liquid waste, which can then be stored in a smaller space and without the risk of the spills inherent to the initial liquid material. The maximum adsorption capacity of the GK/M in this study was found to be 15.68 GBq/g. We present a thorough morphological characterization of the synthesised GK/M, as well as a discussion of the possible phosphorus adsorption mechanisms.

1. Introduction

Radioactive waste containing radioactive material is usually a by-product of nuclear power generation and other applications of nuclear technology, such as research and medicine. Radioactive waste is hazardous to most forms of life and the environment. As the radioactivity diminishes over time, the waste is typically isolated and stored for a period of time until it no longer poses a hazard. One of the major approaches to managing radioactive waste has been segregated storage [1]. In the case of liquid radioactive waste, the risk of radioactive spills contaminating a large area, while being stored, is high. Efficient remediation of such liquid waste is therefore crucial for increasing safety during the necessary storage.

Specifically, the radioactive isotope of phosphorus, ³²P, has been extensively used to trace the path of biochemical reactions. A radioactive tracer can also be used to track the distribution of a substance within a natural system such as a cell or tissue. Radioactive tracers are also used to determine the location of fractures created by hydraulic fracturing in natural gas production. Radioactive tracers also form the basis of a variety of imaging systems, such as PET scans, SPECT scans, and Technetium scans [2]. During the synthesis of ³²P-labelled biomolecules, and the use of these compounds in various research activities, a large volume of liquid radioactive waste containing phosphates is generated.

There are several available processes used for the removal of nonradioactive phosphates from wastewater, such as reverse osmosis, biological nitrification, and electrodialysis [3–5]. Most of these approaches are, generally, suitable for the removal of high levels of phosphorus contamination; however, they are less suited for low level contamination. Furthermore, most of these methods are relatively expensive; they generate secondary products, such as sludge and foams, and the toxicity of the used materials is not always clear [6]. For low levels of contamination, adsorption is regarded as one of the most effective and economical processes, for which a variety of adsorbents are available [7–9].

Recently, natural gums have been shown to be effective biosorbents for the remediation of toxic heavy metal ions [10–13]. These natural gums are relatively inexpensive, biodegradable, and nontoxic hydrocolloids, which are amenable to both chemical and biochemical modifications [14]. Extensive research has been carried out on Gum Karaya (GK), a partially acetylated polysaccharide produced as an exudate by trees, with a branched structure and a high molecular mass [15]. GK contains about 60% neutral sugars and 40% acidic sugars and is mainly used for food, and nonfood, applications due to its acid stability, high viscosity, and suspension properties [14, 16].

With gum as the adsorbent, magnetic nanoparticles have been successfully used to further improve the efficiency of biosorption by increasing the accessible surface area for the adsorbate [17]. Besides, biomagnetic nanoparticles have great potential in water treatment as their recovery is energy efficient and environmentally friendly. For such an application, it is necessary to use purification methods that do not generate secondary waste and involve only recyclable materials that can be easily used on an industrial scale. Nanoparticles of metal oxides are candidate materials for providing better kinetics for the adsorption of metal ions from aqueous solutions [18, 19].

Specifically, magnetite nanoparticles have attracted increasing research interest in environmental remediation in recent years. Good adsorption activities of magnetite nanoparticles for many heavy metal ions have been reported in the literature [20]. In the water treatment industry, adsorption of phosphate by magnetite has proven to be an effective technique for removing phosphorus from wastewater [21–30]. Magnetite is used not only because of its strong adsorption activity but also because it can be easily separated and collected by an external magnetic field. By this means, it has the capability to treat large amounts of wastewater within a short period of time and then be conveniently separated from the water. Moreover, it can be modified using functionalized polymers and novel molecules to impart surface reactivity.

In this study, we present a novel nontoxic biomagnetic nanoadsorbent, based on surface modification of magnetic iron oxide nanoparticles with Gum Karaya, for the adsorption of radioactive phosphates from liquid radioactive waste. The synthesised Gum Karaya/magnetite (GK/M) nanoparticles are characterised and investigated as an environmentally friendly mediator in the bioremediation of phosphorus. To the best of our knowledge, this is the first time a nanocomposite of a tree-gum and magnetite is used for the bioremediation of radioactive phosphates generated during the synthesis of ³²P-labelled biomolecules. We also present a detailed study of the adsorption characteristics of the material.

2. Experimental Section

2.1. Materials

Gum Karaya (GK) powders, FeCl₃·6H₂O, FeCl₂·4H₂O, and NH₄OH, were purchased from Sigma-Aldrich (Sigma-Aldrich Company LTD, MO, USA). The ³²P effluents generated during the synthesis [31] of ³²P-labelled biomolecules were collected, and the radioactive concentration was determined using liquid scintillation counting (Tri-Carb 2910 TR, Liquid Scintillation Analyser, Perkin Elmer, USA). All chemicals were of analytical grade and used as received without any further purification.

2.2. Synthesis of GK/M Nanocomposites

Iron oxide nanoparticles were prepared by coprecipitating Fe²⁺ and Fe³⁺ ions with a NH₄OH solution and treated under hydrothermal conditions [32]. In detail, that means that 25 mg of GK was suspended in 50 mL Milli-Q-deionized water and agitated at 100 rpm for 15 min to achieve complete dissolution. Another solution containing a mixture of 0.3 M FeCl₂ and FeCl₃ (Fe²⁺ : Fe³⁺ = 2 : 1) dissolved in Milli-Q-deionized water was then added to the aqueous gum medium. The whole mixture was kept at ~363 K in a water bath under vigorous stirring. During the reaction process, a suitable amount of NH₄OH solution was gradually added into the mixture and the pH was maintained above 10. The formation of a black ferrofluidic mixture was observed during the reaction, indicating the formation of iron oxide nanoparticles. Stirring was continued for 30 min. After that, the ferrofluidic mixture was cooled down to room temperature (298.15 K). The resulting GK/M colloidal dispersion was washed several times with Milli-Q water and separated with the help of an external magnetic force. As a last step, the dispersion was freeze-dried to the form of nanocomposites.

2.3. Characterization of GK/M Nanocomposites

The composition and morphology of the GK and GK/M nanocomposite were studied using energy dispersive X-ray analysis attached to a scanning electron microscope (ZEISS, Ultra/Plus, Germany). The X-ray diffraction (XRD) pattern of the GK/M nanocomposite was obtained using a Philips X-ray diffractometer with Cu-Kα radiation (Philips PW 3020, Holland) and the ATR-FTIR of GK and GK/M was obtained on a spectrophotometer (NICOLET IZ10, Thermo Scientific FTIR Spectrometer Company, USA). The spectrometer is equipped with a multireflection variable angle horizontal ATR accessory. Transmission electron microscopy (TEM) analysis of the GK/M colloids was performed using a TEM (Tecnai F 12, Japan) operating at an acceleration voltage of 150 kV. X-ray photoelectron spectroscopy (XPS) analysis of powder samples of GK and GK/M was performed on a Kratos AXIS 165 instrument (Shimadzu Corporation, Kyoto, Japan). XPS spectra were obtained by applying an Mg-Kα (1253.6 eV) energy source of monochromatic radiation operating at 15 kV and 10 mA. The residual pressure in the analysis chamber was 5 × 10⁻¹⁰ Torr (6.66 × 10⁻⁸ Pa). Survey scans were recorded in the binding energy range 0–1100 eV (1.76239422 × 10⁻¹⁶ J) with a pass energy of 80 eV (1.28174125 × 10⁻¹⁷ J). Hysteresis loop measurements on the GK/M were performed using a vibrating sample magnetometer (ADE make, model EV9, MicroSense, LLC, Massachusetts, USA) up to field strength of 2 T.

2.4. Batch Mode Adsorption Experiments

Biosorption experiments were conducted using solutions having 3.7 TBq/m³ of ³²P with an optimum GK/M concentration (1000 g/m³). The solutions (100 mL) including the GK/M were shaken for the desired contact time in an electrically thermostatic reciprocating shaker (Innova-43, New Brunswick Scientific Co. LTD, NJ, USA) at 200 rpm. Contact time, optimum pH, initial radioactive phosphate concentration, sorbent dose, and adsorption capacity experiments were performed at room temperature (298 ± 2) K. The batch studies were performed at different experimental conditions such as initial radioactive phosphorus concentration (0.37–3.7 TBq/m³), contact time (10–180 min), pH (2–10), GK/M concentration (0.1–5.0 kg/m³), and temperature (298–328 K). The equilibrium time was estimated by drawing samples at regular intervals until equilibrium was reached. The adsorption (%) of ³²P and adsorption capacity () of GK/M were calculated. The experiments were run in triplicate; the mean of the results obtained is used in the analysis.

2.5. Langmuir and Freundlich Adsorption Isotherm Models

The sorption isotherms of the ³²P on GK/M were determined based on batch experiments at (298 ± 2) K. The GK/M nanocomposite (100 g/m³) was allowed to equilibrate with solutions at different initial ³²P concentrations (0.37–3.7 TBq/m³). The pH value of the solutions was adjusted to (6.0 ± 0.1). The whole mixture was kept at a contact time of 120 min (equilibration time) in an electrically thermostatic reciprocating shaker (Innova-43, New Brunswick Scientific Co., LTD, NJ, USA) at 200 rpm. After the equilibration time, the mixture was centrifuged for 10 min at 5000 rpm. The ³²P concentration in the supernatant was measured using liquid scintillation counting (Tri-Carb 2910 TR, Liquid Scintillation Analyser, Perkin Elmer, USA).

In order to optimize the biosorption process parameter, both Langmuir and Freundlich isotherm models were tested on the experimental results [33, 34]. The Langmuir model, which is based on the assumption that maximum adsorption occurs when a saturated monolayer of solute molecules is present on the adsorbent surface, the energy of adsorption being a constant and with no migration of adsorbed molecules in the surface plane, is given by where and are the equilibrium and maximum uptake capacities, is the equilibrium concentration, and is the Langmuir isotherm constant related to free energy of adsorption. The slope of the plot of against gives 1/, the intercept 1/.

The Freundlich isotherm model is given by the equation where and are Freundlich’s constants related to the adsorption capacity and intensity of adsorption, respectively. The values of and can be determined from the log-log plot of versus as the intercept and slope, respectively.

2.6. Kinetic Studies

In order to examine the controlling mechanism of the adsorption process, kinetic models are used to test the experimental data. The kinetic adsorption data can be processed to understand the dynamics of the adsorption reaction in terms of the order of the rate constant. Pseudo-first-order and pseudo-second-order kinetic models may present the process of ³²P adsorption by the GK/M nanocomposite from the radioactive effluents. Conformity between the experimental data and the model-predicted values is expressed by the correlation coefficient (). The closer its value is to unity, the more accurately the model describes the kinetics of adsorption.

The pseudo-first-order kinetic model describes the adsorption rate based on the adsorption capacity. Its linear form is generally expressed as where and are the adsorption capacity and adsorption at time , respectively, and is the first order rate constant. A plot of log () versus gives as the slope and log as the intercept value.

The pseudo-second-order model applied to adsorption kinetics was given by Ho and McKay [35] as where is the amount of sorbate on the sorbent at time , is the rate constant of pseudo-second-order sorption kinetics, and is the equilibrium uptake. The plot of versus should show a linear relationship, if the second-order kinetics are applicable. Values of and were calculated from the intercept and slope of the plots.

2.7. Thermodynamics of Adsorption

The energy of activation for the adsorption processes was calculated by using the Arrhenius equation, and other thermodynamic parameters such as change in free energy, enthalpy, and entropy associated with the adsorption process. The energetics of the adsorption process was also examined by temperature studies. The temperature dependency on the rate of a reaction is important to predict the feasibility of the reaction. Arrhenius has shown the relation between the rate constant and the temperature as follows: where is the rate constant, is the Arrhenius factor, is the universal gas constant, and is the thermodynamic temperature. The value of the activation energy is determined from the slope of versus .

The thermodynamic aspects of ³²P ions adsorption by the GK/M nanocomposite were investigated using thermodynamic parameters such as enthalpy change (), free energy change (), and entropy change (). The free energy change of the adsorption reaction is given by the following equation: where is the free energy change, is the universal gas constant, is the thermodynamic temperature, and () is the distribution coefficient.

According to the Van’t Hoff equation: the enthalpy change () and the entropy change () parameters can be calculated. and values were calculated from the slope and intercept of the plot of versus , respectively.

3. Results and Discussion

3.1. Morphological Characterization

To investigate the surface and particle size distribution of the nanoparticles formed during the chemical process, the morphology of the synthesised GK/M nanocomposite was characterised and compared to that of pure GK. The scanning electron micrograph of GK/M (Figure 1) clearly shows the magnetite beads before phosphate adsorption. Upon the functionalization of the iron oxide nanoparticles, the branched-network morphology of the GK has been significantly modified into spherical aggregate structures containing iron oxide nanoparticles, as illustrated by the TEM micrograph (Figure 2). The size of the iron oxide nanoparticles within the gum matrix was in the range of 10–15 nm.

(a)

(b)

FT-IR characterization was carried out to identify the functional groups that are responsible for the formation of the iron nanoparticles treated with GK. Due to the binding of the iron oxide nanoparticles to the surface of the GK matrix, the intensity of the FT-IR spectra peak at 1036 cm⁻¹ is considerably contracted in the case of the GK/M nanocomposite (Figure 3). The intensity of the O–H stretching at 3,359 cm⁻¹ for the GK/M is lower than that of the native gum. The peaks at 1,721 cm⁻¹ and 1,249 cm⁻¹ (CH₃CO group) present in the GK are displaced in the GK/M samples, which suggests that the acetyl groups play an important role in the formation of the GK/M nanocomposite. Another peak shift, from 1,427 cm⁻¹ to 1,370 cm⁻¹, is observed in the case of GK/M, implying that both the carbonyl and hydroxyl functional groups of GK have a strong affinity to bind the magnetite nanoparticles. The lower peak at 1,604 cm⁻¹ in the GK/M, compared to the peak for GK, indicates that the negatively charged COO groups bind to positive sites in the surface of the magnetite.

XRD analysis was performed to evaluate the formation of the GK/M nanocomposite. The amorphous nature of GK can be seen from the XRD patterns (Figure 4(a)), which have no intense peaks. GK/M on the other hand (Figure 4(b)), has distinct peaks corresponding to the formation of iron oxide nanoparticles within the network of the GK matrix. The diffraction peaks at 30.4°, 35.9°, 43.5°, 52.9°, 57.3°, and 62.8° correspond to the (220), (311), (400), (422), (511), and (440) planes of bulk crystalline magnetite (JCPDS number 75-1610), respectively. The XRD pattern thus clearly shows that the synthesised iron oxide nanoparticles are crystalline in nature. A broadening of peaks due to the small crystal size effect can be seen in the case of GK/M. The crystallite size, calculated using the Debye-Scherer formula [36], is ~(11.0 ± 5.0) nm, which is in good agreement with the aforementioned range of 10–15 nm obtained by the TEM analysis.

(a)

(b)

We used XPS to further confirm the presence of magnetite and find its oxidation state. The XPS survey scan (Figure 5), shows the binding energy peaks of carbon and oxygen in GK and in the case of GK/M the Fe2p spectrum for magnetite. The 2P_3/2 peak is centred at binding energy 710.2 eV (1.1378658 × 10⁻¹⁶ J), and the 2P_1/2 peak is at 732.8 eV (1.17407499 × 10⁻¹⁶ J), which matches well with the reference data of magnetite [37].

(a)

(b)

The magnetic properties of GK/M were investigated using a vibrating sample magnetometer at room temperature with an applied field ranging from −398 to 398 A/m. The hysteresis loop of the GK/M nanocomposite (Figure 6) shows ferromagnetic behaviour with magnetic saturation values of ~60 m²A/kg. The magnetization values indicate that GK/M can have a strong magnetic response and therefore can easily be separated from the solution with the help of an external magnetic force. This magnetization value of GK/M is comparable to earlier reported values for magnetic chitosan nanocomposites [38], another natural product, showing that GK/M might have the same potential for applications as the widely used chitosan.

3.2. Adsorption Study

The maximum adsorption (%) of ³²P, obtained from adsorption experiments conducted at different pH (1–10) (Figure 7) was found to be at pH 5–7 and reaches (96.4 ± 1.0)%. Fe(OH)₃ is found in a hydrated form and precipitates as an amorphous complex that changes its structure over time. The mechanisms responsible for this are ion exchange and precipitation of ³²P on the surface of the GK/M nanocomposite. It was suggested [39] that phosphates form bonds with the metal hydroxyl complex. These bonds are very strong and bind the phosphate to the structure. It was previously reported that the stoichiometric ratio of metal and phosphorus in the precipitant depends on many factors, including the phosphate concentration in the liquid, the chemical dose, the age of the hydroxyl complex, and mixing [40, 41].

Our previous work on pure Gum Karaya [15] indicates that the formation of complexes with phosphorous is favoured due to the high amount of calcium present in the gum. It was previously reported [30] that calcium ions can form stable complexes with phosphorus and that a high amount of calcium enhances the retention capacity of phosphorus irrespective of pH. Several studies have shown that Ca²⁺ was effective for the removal of phosphorus from an aqueous solution by surface precipitation. Magnetite surface was used as nucleus for heterogeneous Ca-phosphate precipitation [42, 43]. It was earlier reported that phosphate adsorbed on magnetite by inner-sphere complex mechanism [44].

We further investigated the adsorption capacity for ³²P as a function of GK/M nanocomposite dosage (Figure 8). The removal of ³²P was found to be dependent on the concentration of the GK/M nanocomposite. We find the expected result [13] that with an increase in the nanocomposite concentration the metal removal efficiency is enhanced due to an increase in the number of adsorption sites. On the other hand, with an increase of the GK/M nanocomposite concentration from 0.1 to 1 kg/m³, the adsorption capacity decreased from (562.4 ± 9.25) to (360.75 ± 6.66) MBq/g (Figure 8). Increasing the concentration further has no effect on the adsorption, as saturation is achieved. The drop in adsorption capacity is due to an excess of adsorption sites that due to a lack of material remain unsaturated during the adsorption process. The effect of the contact time on ³²P adsorption on the GK/M nanocomposite was also studied (Figure 9) and we observed an increase in the adsorption capacity of ³²P by the GK/M nanocomposite with an increase in the contact time. The initial rapid adsorption changes to a very slow process and the equilibrium point is reached after 120 min. The nature of the adsorbent and its available sorption sites affected the time needed to reach equilibrium.

To reveal the specific relation between the concentration of the adsorbate and the adsorption capacity of the adsorbent at a constant temperature, we interpreted the experimental equilibrium adsorption data using nonlinear forms of the Langmuir and Freundlich isotherm models. The Langmuir isotherms for adsorption of ³²P on GK/M at optimized experimental conditions (Figure 10) give the maximum amount of ³²P adsorbed to be 15.68 GBq/g. The adsorption energy is 3 × 10⁻⁶ m³/g. The nonlinear Freundlich isotherm (Figure 11) giving and , also satisfactorily describes the relationship between the amount of ³²P adsorbed by the nanocomposite and its equilibrium concentration in the solution.

We employed the Lagergren first-order kinetic model to describe the adsorption rate based on the adsorption capacity. The first-order kinetic model parameters (Table 1) do not fit the experimental results satisfactorily; therefore, the calculated adsorption capacity does not agree with the experimental values. This is an indication that the biosorption of ³²P by the GK/M nanocomposite does not follow the pseudo-first-order kinetic reaction.

The pseudo-second-order model, based on the sorption capacity of a solid phase, was then used to fit the results. The second-order sorption rate constant () and adsorption capacity () values (Table 1) were determined from the slopes and intercepts of the plots of versus . The values calculated by the model agree perfectly with the experimental values. This suggests that the biosorption follows the pseudo-second-order model. This model is based on the assumption that the rate-limiting step may be a chemical sorption involving valence forces through sharing or exchange of electrons between the adsorbent and the adsorbate [45]. This provides the best correlation for the experimental data.

We further examined the energetics of the adsorption process by thermodynamic studies. The temperature dependence on the rate of reaction is important to predict the feasibility of the reaction. It can be described by a simple but remarkably accurate formula, Arrhenius’ equation. When evaluated, the activation energy is , and the preexponential factor is . From the value of the activation energy, we can derive whether the adsorption mechanism is diffusion-controlled () or surface-controlled () [46]. The activation energy therefore clearly indicates that the adsorption of ³²P on the GK/M nanocomposite is a chemical precipitation process, that is, a surface-controlled reaction.

The thermodynamic aspects of ³²P ion adsorption by the GK/M nanocomposite were further investigated based on the equation in Section 2.7. The Gibbs free energy change () for the adsorption of the ³²P ions on the GK/M nanocomposite was found to be −10.49 kJ/mol at a temperature of 298 K, −10.84 kJ/mol at 308 K, −11.19 kJ/mol at 318 K, and −11.34 kJ/mol at 328 K. The negative value of the Gibbs free energy change indicates that the biosorption is thermodynamically feasible and of a spontaneous nature. Furthermore, the decrease of the Gibbs free energy change with increasing temperature shows a decrease in the feasibility of the biosorption.

In the temperature range of 298.15–328.15 K at an initial pH of 6 and initial ³²P concentration of 3.7 TBq/m³, the enthalpy change is and the entropy change is . The positive value of the enthalpy change shows that the biosorption of ³²P ions on the GK/M nanocomposite is endothermic in nature; that is, the values decrease with increasing temperature. The positive value of suggests some structural changes in the adsorbate and the adsorbent during the adsorption process [47].

3.3. Storage of ³²P Effluents

After adsorption of ³²P by the GK/M, the excess aqueous phase was removed from the mixture using a speed Vac concentrator. The ³²P content was also determined using liquid scintillation and no radioactive contamination was found in the aqueous phase. The ³²P adsorbed by the GK/M was stored until a negligible level of radioactive contamination was detected in this nano-composite. The results indicated that the GK/M could be developed as a green biosorbent for effective storage of radioactive isotopes and it could also help to reduce the amount of liquid radioactive waste in a gel form, in order to save precious water.

3.4. Desorption

In order to apply biosorbent to real industrial effluent samples, desorption process of toxic material is essential.Almost 98% of the adsorbed ³²P was desorbed from the GK/M nanogel using 0.1 N HCl as an eluent. The release of ³²P from the GK/M by acid suggests an ion-exchange mechanism. The adsorption-desorption cycle was repeated five times with the same adsorbent using 0.1 N HCl. The adsorption capacity with the regeneration cycles varied from 98% to 90% from one to five cycles of operation.

4. Conclusions

In this work, we synthesised and characterised a Karaya hydrocolloid stabilized magnetite. This composite of gum and magnetite was then successfully used for the removal of radioactive phosphates generated from ³²P-labelled biomolecules. To the best of our knowledge, no other material for the removal of radioactive phosphorus has been presented so far. The presented study shows that the synthesised magnetite effectively removes radioactive phosphorus, especially at low concentrations of input phosphorus, with a maximum adsorption capacity of 15.68 GBq/g. The contact and sedimentation times of the presented remediation method are also relatively short, which is a desirable property for real-life application. Based on our findings, the possibility arises to fabricate nontoxic hydrocolloid-based magnetic nanohydrogels that could be used for the long-term storage of initially liquid radioactive waste. The results for phosphorus further suggest that the studied biodegradable hydrocolloid-based materials could be used for the efficient remediation of other radionuclides. The presented material also represents a green alternative to common methods of nonradioactive phosphate removal.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The research reported in this paper was in part supported by the Project OPR&DI, Centre for Nanomaterials, Advanced Technologies, and Innovation (no. CZ.1.05/2.1.00/01.0005), by the Project Development of Research Teams of R&D Projects at the Technical University of Liberec (no. CZ.1.07/2.3.00/30.0024), and by the Competence Centre (no. TE01020218). Experiments involving radioactive matter were conducted at Jonaki, BRIT, Hyderabad, India.

References

A. Hagen, “Waste management-nuclear power, man and the environment,” IAEA Bulletin, vol. 24, no. 2, pp. 3–5, 2007.
View at: Google Scholar
H.-S. Wu, W.-S. Huang, Y.-C. Liu, R.-F. Yen, Y.-Y. Shen, and C.-H. Kao, “Comparison of FDG-PET and Technetium-99m MIBI SPECT to Detect Metastatic Cervical Lymph Nodes in Well-differentiated Thyroid Carcinoma with Elevated Serum HTG but Negative I-131 Whole Body Scan,” Anticancer Research, vol. 23, no. 5, pp. 4235–4238, 2003.
View at: Google Scholar
L. Thörneby, K. Persson, and G. Trägårdh, “Treatment of liquid effluents from dairy cattle and pigs using reverse osmosis,” Journal of Agricultural Engineering Research, vol. 73, pp. 159–170, 1999.
View at: Google Scholar
A. M. O. Mohamed, “Development of a novel electro-dialysis based technique for lead removal from silty clay polluted soil,” Journal of Hazardous Materials, vol. 90, no. 3, pp. 297–310, 2002.
View at: Publisher Site | Google Scholar
R. Zhu, M. Wu, H. Zhu, Y. Wang, and J. Yang, “Enhanced phosphorus removal by a humus soil cooperated sequencing batch reactor using acetate as carbon source,” Chemical Engineering Journal, vol. 166, no. 2, pp. 687–692, 2011.
View at: Publisher Site | Google Scholar
D. Zhao and A. K. Sengupta, “Ultimate removal of phosphate from wastewater using a new class of polymeric ion exchangers,” Water Research, vol. 32, no. 5, pp. 1613–1625, 1998.
View at: Publisher Site | Google Scholar
L. E. De-Bashan and Y. Bashan, “Recent advances in removing phosphorus from wastewater and its future use as fertilizer,” Water Research, vol. 38, no. 19, pp. 4222–4246, 2004.
View at: Publisher Site | Google Scholar
S. Wang, H. M. Ang, and M. O. Tadé, “Novel applications of red mud as coagulant, adsorbent and catalyst for environmentally benign processes,” Chemosphere, vol. 72, no. 11, pp. 1621–1635, 2008.
View at: Publisher Site | Google Scholar
M. Ahmaruzzaman, “Adsorption of phenolic compounds on low-cost adsorbents: a review,” Advances in Colloid and Interface Science, vol. 143, no. 1-2, pp. 48–67, 2008.
View at: Publisher Site | Google Scholar
V. T. P. Vinod, R. B. Sashidhar, B. Sreedhar, B. Rama Rao, T. Nageswara Rao, and J. T. Abraham, “Interaction of Pb²⁺ and Cd²⁺ with gum kondagogu (Cochlospermum gossypium): a natural carbohydrate polymer with biosorbent properties,” Carbohydrate Polymers, vol. 78, no. 4, pp. 894–901, 2009.
View at: Publisher Site | Google Scholar
V. T. P. Vinod, R. B. Sashidhar, and B. Sreedhar, “Biosorption of nickel and total chromium from aqueous solution by gum kondagogu (Cochlospermum gossypium): a carbohydrate biopolymer,” Journal of Hazardous Materials, vol. 178, no. 1–3, pp. 851–860, 2010.
View at: Publisher Site | Google Scholar
V. T. P. Vinod, R. B. Sashidhar, and A. A. Sukumar, “Competitive adsorption of toxic heavy metal contaminants by gum kondagogu (Cochlospermum gossypium): a natural hydrocolloid,” Colloids and Surfaces B, vol. 75, no. 2, pp. 490–495, 2010.
View at: Publisher Site | Google Scholar
V. T. P. Vinod, R. B. Sashidhar, N. Sivaprasad et al., “Bioremediation of mercury (II) from aqueous solution by gum karaya (Sterculia urens): a natural hydrocolloid,” Desalination, vol. 272, no. 1–3, pp. 270–277, 2011.
View at: Publisher Site | Google Scholar
D. Verbeken, S. Dierckx, and K. Dewettinck, “Exudate gums: occurrence, production, and applications,” Applied Microbiology and Biotechnology, vol. 63, no. 1, pp. 10–21, 2003.
View at: Publisher Site | Google Scholar
V. T. P. Vinod, R. B. Sashidhar, V. U. M. Sarma, and S. S. Raju, “Comparative amino acid and fatty acid compositions of edible gums kondagogu (Cochlospermum gossypium) and karaya (Sterculia urens),” Food Chemistry, vol. 123, no. 1, pp. 57–62, 2010.
View at: Publisher Site | Google Scholar
D. A. Silva, A. C. F. Brito, R. C. M. de Paula, J. P. A. Feitosa, and H. C. B. Paula, “Effect of mono and divalent salts on gelation of native, Na and deacetylated Sterculia striata and Sterculia urens polysaccharide gels,” Carbohydrate Polymers, vol. 54, no. 2, pp. 229–236, 2003.
View at: Publisher Site | Google Scholar
S. S. Banerjee and D.-H. Chen, “Fast removal of copper ions by gum arabic modified magnetic nano-adsorbent,” Journal of Hazardous Materials, vol. 147, no. 3, pp. 792–799, 2007.
View at: Publisher Site | Google Scholar
L.-S. Zhong, J.-S. Hu, H.-P. Liang, A.-M. Cao, W.-G. Song, and L.-J. Wan, “Self-assembled 3D flowerlike iron oxide nanostructures and their application in water treatment,” Advanced Materials, vol. 18, no. 18, pp. 2426–2431, 2006.
View at: Publisher Site | Google Scholar
J.-S. Hu, L.-S. Zhong, W.-G. Song, and L.-J. Wan, “Synthesis of hierarchically structured metal oxides and their application in heavy metal ion removal,” Advanced Materials, vol. 20, no. 15, pp. 2977–2982, 2008.
View at: Publisher Site | Google Scholar
P. Yuan, D. Liu, M. Fan et al., “Removal of hexavalent chromium [Cr(VI)] from aqueous solutions by the diatomite-supported/unsupported magnetite nanoparticles,” Journal of Hazardous Materials, vol. 173, no. 1–3, pp. 614–621, 2010.
View at: Publisher Site | Google Scholar
S. Yeoman, T. Stephenson, J. N. Lester, and R. Perry, “The removal of phosphorus during wastewater treatment: a review,” Environmental Pollution, vol. 49, no. 3, pp. 183–233, 1988.
View at: Google Scholar
Y. S. R. Chen, J. N. Butler, and W. Stumm, “Kinetic study of phosphate reaction with aluminum oxide and kaolinite,” Environmental Science and Technology, vol. 7, no. 4, pp. 327–332, 1973.
View at: Google Scholar
L. Lijklema, “Interaction of orthophosphate with Iron (III) and aluminum hydroxides,” Environmental Science and Technology, vol. 14, no. 5, pp. 537–541, 1980.
View at: Google Scholar
Y. Arai and D. L. Sparks, “ATR-FTIR spectroscopic investigation on phosphate adsorption mechanisms at the ferrihydrite-water interface,” Journal of Colloid and Interface Science, vol. 241, no. 2, pp. 317–326, 2001.
View at: Publisher Site | Google Scholar
E. Laiti, P. Persson, and L.-O. Öhman, “Balance between surface complexation and surface phase transformation at the alumina/water interface,” Langmuir, vol. 14, no. 4, pp. 825–831, 1998.
View at: Google Scholar
E. Laiti, P. Persson, and L.-O. Öhman, “Surface complexation and precipitation at the H⁺-orthophosphate-aged γ-Al₂O₃/water interface,” Langmuir, vol. 12, no. 12, pp. 2969–2975, 1996.
View at: Google Scholar
P. A. Connor and A. J. McQuillan, “Phosphate adsorption onto TiO₂ from aqueous solutions: an in situ internal reflection infrared spectroscopic study,” Langmuir, vol. 15, no. 8, pp. 2916–2921, 1999.
View at: Publisher Site | Google Scholar
C. Yee, G. Kataby, A. Ulman et al., “Self-assembled monolayers of alkanesulfonic and -phosphonic acids on amorphous iron oxide nanoparticles,” Langmuir, vol. 15, no. 21, pp. 7111–7115, 1999.
View at: Google Scholar
C. Luengo, M. Brigante, J. Antelo, and M. Avena, “Kinetics of phosphate adsorption on goethite: comparing batch adsorption and ATR-IR measurements,” Journal of Colloid and Interface Science, vol. 300, no. 2, pp. 511–518, 2006.
View at: Publisher Site | Google Scholar
B. Nowack and A. T. Stone, “Competitive adsorption of phosphate and phosphonates onto goethite,” Water Research, vol. 40, no. 11, pp. 2201–2209, 2006.
View at: Publisher Site | Google Scholar
T. F. Walseth and R. A. Johnson, “The enzymatic preparation of [α-32P]nucleoside triphosphates, cyclic [³²P]AMP, and cyclic [³²P]GMP,” BBA Section Nucleic Acids And Protein Synthesis, vol. 562, no. 1, pp. 11–31, 1979.
View at: Google Scholar
A.-H. Lu, E. L. Salabas, and F. Schüth, “Magnetic nanoparticles: synthesis, protection, functionalization, and application,” Angewandte Chemie—International Edition, vol. 46, no. 8, pp. 1222–1244, 2007.
View at: Publisher Site | Google Scholar
I. Langmuir, “The constitution and fundamental properties of solids and liquids. Part I: solids,” The Journal of the American Chemical Society, vol. 38, no. 2, pp. 2221–2295, 1916.
View at: Google Scholar
H. T. M. Freudlich, “Over the adsorption in solution,” Journal of Physical Chemistry, vol. 57, pp. 385–471, 1906.
View at: Google Scholar
Y. S. Ho and G. McKay, “Pseudo-second order model for sorption processes,” Process Biochemistry, vol. 34, no. 5, pp. 451–465, 1999.
View at: Publisher Site | Google Scholar
H. P. Klug and L. E. Alexander, X-Ray Diffraction Procedures for Crystalline and Amorphous Solids, Wiley-Interscience, New York, NY, USA, 1974.
Y. Gao and S. A. Chambers, “Heteroepitaxial growth of α-Fe₂O₃, γ-Fe₂O₃ and Fe₃O₄ thin films by oxygen-plasma-assisted molecular beam epitaxy,” Journal of Crystal Growth, vol. 174, no. 1–4, pp. 446–454, 1997.
View at: Google Scholar
X. Liu, Q. Hu, Z. Fang, X. Zhang, and B. Zhang, “Magnetic chitosan nanocomposites: a useful recyclable tool for heavy metal ion removal,” Langmuir, vol. 25, no. 1, pp. 3–8, 2009.
View at: Publisher Site | Google Scholar
M. R. Unnithan, V. P. Vinod, and T. S. Anirudhan, “Ability of iron(III)-loaded carboxylated polyacrylamide-grafted sawdust to remove phosphate ions from aqueous solution and fertilizer industry wastewater: adsorption kinetics and isotherm studies,” Journal of Applied Polymer Science, vol. 84, no. 13, pp. 2541–2553, 2002.
View at: Publisher Site | Google Scholar
C. Vohla, M. Kõiv, H. J. Bavor, F. Chazarenc, and Ü. Mander, “Filter materials for phosphorus removal from wastewater in treatment wetlands: a review,” Ecological Engineering, vol. 37, no. 1, pp. 70–89, 2011.
View at: Publisher Site | Google Scholar
A. Ler and R. Stanforth, “Evidence for surface precipitation of phosphate on goethite,” Environmental Science and Technology, vol. 37, no. 12, pp. 2694–2700, 2003.
View at: Publisher Site | Google Scholar
J. S. Freeman and D. L. Rowell, “The adsorption and precipitation of phosphate onto calcite,” Journal of Soil Science, vol. 32, pp. 75–84, 1981.
View at: Google Scholar
S. Brand-Klibanski, M. I. Litaor, and M. Shenker, “Overestimation of phosphorus adsorption capacity in reduced soils: an artifact of typical batch adsorption experiments,” Soil Science Society of America Journal, vol. 71, no. 4, pp. 1128–1136, 2007.
View at: Publisher Site | Google Scholar
L. Li and R. Stanforth, “Distinguishing adsorption and surface precipitation of phosphate on goethite (α-FeOOH),” Journal of Colloid and Interface Science, vol. 230, no. 1, pp. 12–21, 2000.
View at: Publisher Site | Google Scholar
G. E. Boyd, A. W. Adamson, and L. S. Myers Jr., “The exchange adsorption of ions from aqueous solutions by organic zeolites. II: kinetics,” Journal of the American Chemical Society, vol. 69, no. 11, pp. 2836–2848, 1947.
View at: Google Scholar
C. Liu and P. M. Huang, “Kinetics of lead adsorption by iron oxides formed under the influence of citrate,” Geochimica et Cosmochimica Acta, vol. 67, no. 5, pp. 1045–1054, 2003.
View at: Publisher Site | Google Scholar
J. H. Park and D. I. Jung, “Removal of total phosphorus (TP) from municipal wastewater using loess,” Desalination, vol. 269, no. 1–3, pp. 104–110, 2011.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2014 Vinod Vellora Thekkae Padil et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1861

Downloads

1084

Citations

BioMed Research International

Hydrocolloid-Stabilized Magnetite for Efficient Removal of Radioactive Phosphates

Abstract

1. Introduction

2. Experimental Section

2.1. Materials

2.2. Synthesis of GK/M Nanocomposites

2.3. Characterization of GK/M Nanocomposites

2.4. Batch Mode Adsorption Experiments

2.5. Langmuir and Freundlich Adsorption Isotherm Models

2.6. Kinetic Studies

2.7. Thermodynamics of Adsorption

3. Results and Discussion

3.1. Morphological Characterization

3.2. Adsorption Study

3.3. Storage of 32P Effluents

3.4. Desorption

4. Conclusions

Conflict of Interests

Acknowledgments

References

Copyright

3.3. Storage of ³²P Effluents