Abstract

Microalgae are considered to be a potential major biomass feedstock for biofuel due to their high lipid content. However, no correlation equations as a function of initial nitrogen concentration for lipid accumulation have been developed for simplicity to predict lipid production and optimize the lipid production process. In this study, a lipid accumulation model was developed with simple parameters based on the assumption protein synthesis shift to lipid synthesis by a linear function of nitrogen quota. The model predictions fitted well for the growth, lipid content, and nitrogen consumption of Coelastrum sp. HA-1 under various initial nitrogen concentrations. Then the model was applied successfully in Chlorella sorokiniana to predict the lipid content with different light intensities. The quantitative relationship between initial nitrogen concentrations and the final lipid content with sensitivity analysis of the model were also discussed. Based on the model results, the conversion efficiency from protein synthesis to lipid synthesis is higher and higher in microalgae metabolism process as nitrogen decreases; however, the carbohydrate composition content remains basically unchanged neither in HA-1 nor in C. sorokiniana.

1. Introduction

Microalgae have been considered as a potential biomass feedstock for renewable energy technologies due to its high cellular concentration of lipids, resources sustainability, and greater potential environmental benefits than conventional biofuel [13]. However, realizing industrial production of algal-derived biofuel faces many obstacles; in particular, the cost and technical constraints are the two currently major limits for widespread adoption of algae oil [47]. Therefore, algae-derived oil development may require progress in various scientific and engineering disciplines, such as optimizing cultivation parameters to increase lipid productivities [4, 8, 9]. Considering the assumption that the algae biomass (dry weight) was the sum of protein, lipids, and carbohydrates [5], the lipid productivity could be affected by protein and carbohydrate synthesis. Although the excess carbon fixed by photosynthesis is changed to triacylglycerides synthesis for lipid accumulation under nitrogen starvation, the growth rate of microalgae is reduced since fundamental proteins cannot be synthesized [5, 1012]. On the other hand, mechanism on neutral lipid synthesis about how TAGs are biosynthesized is still in its early stage. Li et al. and Hong et al. [13, 14] observed the competitive relationship between TAGs and carbohydrates biosynthesis after nitrogen depletion. Interestingly, some strains show significant higher quantities of both carbohydrates and lipid during nitrogen-deprived condition [15, 16]. For this reason a suitable way to increase both lipid content and biomass is an urgent and pressing need for producing microalgal biofuels.

The growth model of algae has been well developed with various algae species under different growth environment [1720]. However, the easily adaptable model of algal lipid content is rarely published with respect to various nitrogen concentrations. A new widely simplified applicable mathematical model should be developed for various nitrogen treatments to fully understand the microalgae lipid productivity.

In this study, the lipid content was represented as a linear function of nitrogen quota which was calculated based on the mass balance in the growth medium to study lipid accumulation. It was validated in Coelastrum sp. HA-1 under various initial nitrogen concentrations and applied in Chlorella sorokiniana at different light conditions. The growth was modeled by a nonautonomous differential equation incorporating the logistic equation and adjustment function [14, 15], whereas Michaelis-Menten function was used to model the nitrogen uptake [18, 19].

2. Methods

2.1. Algae Growth Kinetic Modeling

In order to obtain the relationship between culture conditions and the specific growth rate, a simple but useful model (1) was expressed in this work by a nonautonomous differential equation [2123]. where is the specific growth rate of cell population (day−1), is the microalgal concentration at time (g dw·L−1), is the maximum specific growth rate of cells (day−1), is the adjustment function, and is the maximum microalgal concentration during cultivation (g dw·L−1).

Baranyi and Roberts [21, 22] reported based on an assumption that the growth of cells in the lag phase was inhibited by intracellular substance. The adaptation of microalgal cells can be described by when cells entered in a new condition of the bioreactor. Adjustment functionis expressed as where is called the dimensionless parameter of Baranyi-Roberts model. Adjustment function has the following characteristics: it is a monotonic function; ; when , ; when , .

2.2. Nitrogen Assimilation and Nitrogen Quota Modeling

In this work, we assumed that nitrogen uptake is a function of external nitrogen concentration; thus, Michaelis-Menten function [18, 19] was used to simulate nitrogen uptake during cultivation.

The differential equation for nitrogen uptake is expressed aswhere is the external nitrogen concentration at time (g N·L−1), is the maximum nitrogen uptake rate (g N g−1 dw·day−1), and is the half-saturation coefficient of nitrogen uptake (g N·L−1).

Integration of (3) yields the remaining nitrogen in the growth media at time . The nitrogen quota that is defined as the rate between the mass of internal nitrogen and total dry weight of biomass can be obtained by mass balance [24]. It is expressed as where is the nitrogen quota at time (g N g−1 dw), is the initial nitrogen concentration in growth media (g N·L−1), is the initial nitrogen quota (g N g−1 dw), and is the initial microalgal concentration (g dw·L−1).

2.3. Lipid Accumulation Modeling

The conversion efficiency from protein synthesis to lipid or carbohydrate synthesis is higher and higher in microalgae metabolism process when nitrogen is depleted causing a change in the biomass composition [20, 25]. Once nitrogen is depleted, lipid content increased from 9 percent to 62 percent of dry weight; however, protein content decreased from 53 percent to 23 percent of dry weight, and carbohydrate content increased a little in the biomass [20]. The lipid accumulation model thus was expressed as (5) by assuming that the biomass is made up of protein, lipid, and carbohydrate, and protein synthesis shifts to lipid synthesis with nitrogen depletion. where is the lipid content (g Lipid g−1 dw), is the nitrogen-to-protein conversion factor, and is the carbohydrate content of biomass (g carbohydrate g−1 dw).

After rearranging (4)-(5) and replacing . with , the lipid content becomes

We could easily obtain the lipid content according to (6) by analyzing nitrogen concentrations and microalgal biomass.

2.4. Experimental Approach

The seeds of Coelastrum sp. and C. sorokiniana were cultured to logarithmic phase for further use in 250 mL Erlenmeyer flasks with 150 mL F medium (nutrient elements are twofold compared to those in f/2 medium) and Kuhl medium under continuous illumination (100 μmol·m−2·s−1), respectively [26, 27]. The temperature was maintained at 25°C; pH was adjusted to 7.5 initially.

In order to evaluate the effect of nitrogen on the dry weight and lipid yield of the Coelastrum sp. within 24 days, the F medium with 150 μmol·m−2·s−1 was modified by adjusting NaNO3 concentrations to 0.075, 0.15, 0.3, 0.6, and 0.9 g·L−1. For model application on fresh water microalgae C. sorokiniana, the cells were cultivated in modified Kuhl medium with 1 g·L−1 NaNO3 under different light intensities (50, 100, and 200 μmol·m−2·s−1). In the experiments, 50 mL logarithmic phase seed cells were centrifuged and resuspended with the corresponding medium to wipe out the effect of residual nitrogen source and then transferred to glass columns (4.1 cm in diameter, 37 cm in height) with 2% (v/v) CO2 at 25°C. The cell concentration (OD680) of each column reactor was approximately 0.2. For dry weight measurement, microalgal culture sample (10 mL) was filtered through pretreated glass-fiber filter paper (0.8 μm pore size); then 0.5 mole solution of ammonium formate was used to wash the filter paper in order to remove salt. Finally, the filter paper was dried 24 h at 105°C [28, 29]. The dry weight was calculated by the difference between the cell-containing dried filter paper and the weight before filtration. The lipid content and nitrogen concentration were measured according to Yuan et al.’s method [29]. All experiments were performed with triplicates.

2.5. Parameter Estimation

In order to determine the parameter values of (6), the MATLAB routine was firstly used to estimate the parameter values of (1) and (3) which were integrated by Runge-Kutta integration method. Then, (6) was used for fitting the experimental data of lipid content under different initial nitrogen concentrations. For HA-1, the parameter values and simulation were shown at different initial nitrogen concentrations in Table 1. The parameter values of the model for predicting growth, lipid content, and nitrogen uptake of Chlorella sorokiniana were in Table 2.

3. Results and Discussion

3.1. Effect of Initial Nitrogen Concentration on the Final Lipid Content in Coelastrum sp. HA-1

The final lipid content of HA-1 under low initial nitrogen concentration was higher than those with high nitrogen concentration (Figure 1(c)). It might be explained from the point of energy balance that cell growth will not continue under low nitrogen concentration. However, carbon fixation is still in progress at rates exceeding the needs of the cell. In order to maintain a safe turnover of the ATP and reductant pools sustained by light reaction, neutral lipid synthesis is upregulated because fatty acid production needs more ATP and reductant than other substance production in cell; neutral lipids store significantly more energy and its synthesis requires twice energy than carbohydrate or protein [30].

In order to quantify the relationship between initial nitrogen concentration and the final lipid content in HA-1, a correlation equation of was firstly given by polynomial fitting with initial nitrogen concentrations. The empirical correlation equation of was

Based on (6), the final lipid content could be calculated by initial nitrogen concentration when algal concentration reached the maximum value. After rearranging (6) and (7), the final lipid content could be expressed as where is the final lipid content (g Lipid g−1 dw). The simulation result of (8) is meaning for final lipid content data (Figure 2(a)).

The simulation of (7) agreed with the initial nitrogen concentration data to a great degree (Figure 2(b)), and the simulation was 0.9982. Equation (7) showed that the relationship between and initial concentration of nitrogen was not linear, especially when the initial concentration of nitrogen was higher in growth medium (Figure 2(b)). Compared to high nitrogen conditions, the maximum microalgal concentration increased significantly with the nitrogen concentration increasing under low nitrogen conditions. The biomass with 0.3 g·L−1 nitrogen was about 1.86-fold compared to those in 0.075 g·L−1 nitrogen medium. While the nitrogen increased from 0.6 to 0.9 g·L−1, the maximum microalgal concentration was only increased about 11.1%. Although the growth decreased with nitrogen concentration increasing, the final microalgal concentration increased to 6.48 g·L−1. The results strongly imply that growth is limited by another nutrient or light intensity when BG-11 is rich in nitrogen. A similar result was also reported by Packer et al. [24].

Equation (8) showed that the final lipid content could be described as a function of initial nitrogen concentration. Decreasing the initial nitrogen concentration is a good method to obtain high lipid production especially for outdoor cultivation. It is important to note that the range of initial concentration of nitrogen for artificial regulation needs to be obtained based on experimental data under a certain cultivation condition. Based on (7) and (8), a two-stage cultivation process may be an effective way to reach great lipid productivity, similar to the previous reports [3134]. The first stage increases biomass by controlling high initial concentration and then improves the lipid content by controlling low initial nitrogen concentration in lipid accumulation stage. This model also can be used for other microalgal species by adjusting parameter values.

3.2. Models Validation in HA-1

The simulation results of (1)–(6) for dry weight (Figure 1(a)), NaNO3 concentration (Figure 1(b)), and lipid content (Figure 1(c)) were in agreement with the experimental data. With the increase of initial nitrogen concentration, the maximum specific growth rate was basically stable. In order to explain the relationship between and initial NaNO3 concentration, we fit and initial NaNO3 concentration () to build a linear model: . Meanwhile, is a monotonic function, , when , . Hence, can indicate the grow rate of microalgae in difference initial NaNO3 concentrations. The value of was negative at different nitrogen concentrations and trended to decrease with an increase of the initial concentration of nitrogen. Figure 1(a) showed the mathematical model fitting of growth with the average of repeated experimental values. For low nitrogen levels (0.075 and 0.15 g·L−1 NaNO3), the short logarithmic phase resulted in low cell density. However, in 0.6 and 0.9 g·L−1 NaNO3 groups, the logarithmic phase of the cells exceeds 20 days and the maximum biomass was 6.48 g·L−1 at 0.9 g·L−1 initial NaNO3 concentration. Figure 1(b) showed that NaNO3 with initial concentrations of 0.075, 0.15, and 0.3 were absolutely depleted at the 4th day and with 0.6 and 0.9 g·L−1 were depleted at the 8th day. Meanwhile, lipid content was increasing sharply when NaNO3 was depleted and subsequently became stable (Figure 1(c)). The results and (7) imply that biomass and lipid accumulation can be controlled by nitrogen supply in a certain range in terms of other conditions unchanged. However, the varying uncontrollable culture conditions for large scale open outdoor restricted the application. Thus, we further discussed application of light, one of the restricting factors, in our model.

The maximum lipid content was 38% which was reached in 0.075 g·L−1 NaNO3 after 24 days. As initial concentration of NaNO3 is increasing, the final lipid content decreased from 38% to 25% (Figure 1(c)). These results indicate that nitrogen quota is the key factor for lipid accumulation, especially on the nitrogen limitation condition. The similar results were also reported in previous literatures [24, 3537].

As illustrated in Table 1, a simple sensitivity analysis for parameters of the model was performed based on two repeats, and all of the parameter values had a range for the model. The sensitivity results show that the model is stable for HA-1 in two repeats.

3.3. Model Application for C. sorokiniana under Photoautotrophic Condition

In order to extend application of the model in other microalgal species under various cultivation conditions, the model was used to predict the growth, NaNO3 consumption, and lipid accumulation of the C. sorokiniana under phototrophic cultivation condition.

Based on these experimental data, the model was used to predict the growth, lipid content, and NaNO3 consumption (Table 2). The values of the nitrogen-to-protein conversion factor, the carbohydrate content of biomass, and were estimated according to the final lipid content of C. sorokiniana. The parameters and of Coelastrum sp. HA-1 at 0.9 g·L−1 initial NaNO3 concentration were used directly; then the final lipid content and the biomass data of C. sorokiniana at different light intensity were as target to estimate , , , , and Φ using (1), (3), and (6). In addition, the sensitivity analysis was analyzed in Section 3.5.

The growth of C. sorokiniana was slow (Figure 3(a)) under phototrophic cultivation condition. After 7 days, the maximum dry weight (0.77 g·L−1) for C. sorokiniana was reached under 50 μmol·m−2·s−1 of light intensity. The data of NaNO3 consumption (Figure 3(b)) of C. sorokiniana were similar to HA-1. According to the predictions, NaNO3 was completely depleted around days 12, 12, and 15 at 50, 100, and 200 μmol·m−2·s−1, respectively.

The predictions of lipid content of C. sorokiniana were shown in Figure 3(c) under light intensity of 50, 100, and 200 μmol·m−2·s−1. During logarithmic phase, the lipid content of C. sorokiniana decreased for three types of light conditions. The lipid content of C. sorokiniana was to increase when the NaNO3 was depleted at 50, 100, and 200 μmol·m−2·s−1; however, the final lipid content for 50, 100, and 200 μmol·m−2·s−1 was only 15.28%, 14.84%, and 10.42%, respectively (Figure 3(c)), which was lower than initial lipid content. These predictions may imply that, when the growing environment is comfortable for microalgae, the photosynthate is mainly used for growth. Both biomass and lipid content for C. sorokiniana are low under phototrophic condition, which may imply that the C. sorokiniana is not suitable for phototrophic cultivation, or the growth medium may be a bottleneck for growth or lipid accumulation [38].

3.4. Neutral Lipid Productivity of HA-1 and C. sorokiniana

As demonstrated in Figure 4, the maximum neutral lipid productivity of HA-1 was 0.083 g·L−1·day−1 for 0.6 g·L−1 initial nitrogen concentration at 24th day. For 0.075, 0.15, 0.3, and 0.9 g·L−1 the neutral lipid productivity was 0.023, 0.036, 0.064, and 0.069 g·L−1·day−1, respectively. The lipid productivity of C. sorokiniana was only 0.013, 0.0089, and 0.0065 g·L−1·day−1 at 50, 100, and 200 μmol·m−2·s−1, respectively.

3.5. Sensitivity Analysis

As showed in Figure 5, a sensitivity analysis was performed by increasing and decreasing each input by 20%, then estimating -ratios of each input parameter for the variance of lipid content of C. sorokiniana using analysis of variance to the model. Sensitivity results for 50, 100, and 200 μmol·m−2·s−1 were presented in Figures 5(a), 5(b), and 5(c), respectively.

The -ratio value of parameter (carbohydrate content) in (6) was not shown in Figure 5, because the relationship between parameter and lipid content was linear. It was sensitive for the model when the parameter value of carbohydrate content changed. The -ratio values of parameter were 1.131 × 1016, 5.796 × 1015, and for 50, 100, and 200 μmol·m−2·s−1, respectively. Hence, the value of parameter should be firstly determined by mass balance or experiment when the model is applied in other algal species.

For all of light conditions, variables associated with nitrogen-to-protein conversion factor, Baranyi-Roberts parameter, and the maximum algal concentration have a significant effect on lipid accumulation. The model is insensitivity to variance of lipid content in some parameters such as the parameter under different light conditions.

Those variables with a -ratio greater than the -ratio at 95% confidence interval have a large effect on the model outputs and thus need to be obtained more accurately than those in this interval when adapting the model to other algal species.

4. Conclusion

Lipid content has been modeled by a linear function of nitrogen quota of cell, and the growth of microalgae has been simulated by a kinetic model at different initial nitrogen concentrations and light intensities. The model was validated in HA-1 and applied in C. sorokiniana. After sensitivity analysis for the model, carbohydrate content, nitrogen conversion factor, and the maximum algal concentration were significant effect on lipid accumulation. Upregulating initial nitrogen concentrations helped in producing higher biomass, and low nitrogen levels accelerated lipid accumulation. Thus, multiscale regulation of nitrogen was beneficial to get higher lipid productivity in commercial scale.

Competing Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Authors’ Contributions

Zhenhua Yang, Yue Zhao, and Yuyong Hou designed the experiment. Zhenhua Yang and Yue Zhao performed the experiment. Zhiyong Liu analyzed the data with Chenfeng Liu. Zhipeng Hu and Yuyong Hou wrote the paper. All authors read and agreed on the final paper. Zhenhua Yang and Yue Zhao contributed equally to this work.

Acknowledgments

The authors thank Fangjian Chen (Tianjin Institute of Industrial Biotechnology, Chinese Academy of Sciences) for analysis of mathematical model. This work was supported partly by the Key Program for International Cooperation Projects of Sino-Canada (no. 155112KYSB20160030), the National Natural Science Foundation of China (Grant no. 31570047), the Hi-Tech Research and Development Program (863) of China (2014AA0221003), and Key Program for International S&T Cooperation Projects of China (2014DFA61040).