Table of Contents
Conference Papers in Science
Volume 2015 (2015), Article ID 548238, 6 pages
http://dx.doi.org/10.1155/2015/548238
Conference Paper

A Novel Test Method to Determine the Wear Resistance of Agricultural Cutting Tools with an Analyzing Method Based on an Ellipse-Fit Algorithm

FMDauto, University of Applied Sciences Düsseldorf, Josef-Gockel-Strasse 9, 40474 Düsseldorf, Germany

Received 1 August 2014; Revised 18 December 2014; Accepted 22 December 2014

Academic Editor: Michael Moseler

This Conference Paper is based on a presentation given by Hunn Sim at “European Symposium on Friction, Wear, and Wear Protection” held from 6 May 2014 to 8 May 2014 in Karlsruhe, Germany.

Copyright © 2015 Andreas Jahr et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. ADM Germany GmbH, Statistische Informationen zum Getreide- und Futtermittelmarkt, 2014, http://www.acti.de.
  2. K. J. Wild, V. Walther, and J. K. Schueller, “Optimizing fuel consumption and knife wear in a self-propelled forage chopper by improving the grinding strategy,” in Proceedings of the American Society of Agricultural and Biological Engineers Annual International Meeting, pp. 5899–5916, Reno, Nev, USA, June 2009. View at Scopus
  3. Landtechnik 55, Häckslermesser und Gegenschneide eines Feldhäckslers, 2000.
  4. ASTM Standard G65; 2004, Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus, ASTM International, West Conshohocken, Pa, USA, 2010, http://www.astm.org/.
  5. H. Czichos and K.-H. Habig, Tribologie-Handbuch, chapter 1, Vieweg+Teubner, Wiesbaden, Germany, 3rd edition, 1991.
  6. J. Kurzynski, Entwicklung eines Verfahrens und Ermittlung von Werkstoffkennwerten für eine Beanspruchungsgerechte Auswahl verschleißbeständiger Stähle, Forschungsbericht, Verlag und Vertriebsgesellschaft, Düsseldorf, Germany, 1999.
  7. J. Fehrmann, G. Bernhardt, M. Flanhardt, and A. Achimas, “Standzeiterhöhung der Werkzeuge bei der Strohzerkleinerung durch Optimieren von Werkzeugform, Werkstoff und Materialbehandlungsverfahren,” in VDI/MEG-Tagung Landtechnik Hannover 4-5, November 2005, VDI-Berichte 1895, pp. 425–433, Düsseldorf VDI, 2005. View at Google Scholar
  8. A. Heinrich, Grundlagen für ein Messsystem zur Bestimmung des Verschleißzustandes des Häckselaggregates eines Feldhäckslers, TUDPress, 2007.
  9. T. S. R. Murthy, “A comparison of different algorithms for circularity evaluation,” Precision Engineering, vol. 8, no. 1, pp. 19–23, 1986. View at Publisher · View at Google Scholar · View at Scopus
  10. P. Sturm and P. Gargallo, “Conic fitting using the geometric distance,” in Computer Vision—ACCV 2007, Y. Yagi, S. B. Kang, I. S. Kweon, and H. Zha, Eds., vol. 4844 of Lecture Notes in Computer Science, pp. 784–795, Springer, Berlin, Germany, 2007. View at Publisher · View at Google Scholar
  11. F. Tikal, Schneidkantenpräparation—Ziele, Verfahren und Messmethoden: Berichte aus Industrie und Forschung, Kassel University Press, Kassel, Germany, 2009.
  12. A. W. Fitzgibbon, M. Pilu, and R. B. Fisher, “Direct least squares fitting of ellipses,” in Proceedings of the 13th International Conference on Pattern Recognition (ICPR '96), pp. 253–257, Vienna, Austria, August 1996. View at Publisher · View at Google Scholar · View at Scopus