Table of Contents Author Guidelines Submit a Manuscript
Case Reports in Dentistry
Volume 2016, Article ID 1354186, 7 pages
http://dx.doi.org/10.1155/2016/1354186
Case Report

Chairside Fabrication of an All-Ceramic Partial Crown Using a Zirconia-Reinforced Lithium Silicate Ceramic

1Dental Practice, 63456 Hanau, Germany
2Department of Prosthetics, University Medical Center Göttingen, 37075 Göttingen, Germany
3Department of Cariology, Endodontology and Periodontology, University of Leipzig, 04103 Leipzig, Germany

Received 21 December 2015; Accepted 16 February 2016

Academic Editor: Jamil A. Shibli

Copyright © 2016 Sven Rinke et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. D. Fasbinder, “Using digital technology to enhance restorative dentistry,” Compendium of Continuing Education in Dentistry, vol. 33, no. 9, pp. 666–672, 2012. View at Google Scholar
  2. D. J. Poticny and J. Klim, “CAD/CAM in-office technology: innovations after 25 years for predictable, esthetic outcomes,” Journal of the American Dental Association, vol. 141, supplement 2, pp. 5S–9S, 2010. View at Google Scholar · View at Scopus
  3. K. Baroudi and S. N. Ibraheem, “Assessment of chair-side computer-aided design and computer-aided manufacturing restorations: a review of the literature,” Journal of International Oral Health, vol. 7, no. 4, pp. 96–104, 2015. View at Google Scholar
  4. S. Ting-shu and S. Jian, “Intraoral digital impression technique: a review,” Journal of Prosthodontics, vol. 24, no. 4, pp. 313–321, 2015. View at Publisher · View at Google Scholar · View at Scopus
  5. J.-G. Wittneben, R. F. Wright, H.-P. Weber, and G. O. Gallucci, “A systematic review of the clinical performance of CAD/CAM single-tooth restorations,” International Journal of Prosthodontics, vol. 22, no. 5, pp. 466–471, 2009. View at Google Scholar · View at Scopus
  6. D. J. Fasbinder, “Clinical performance of chairside CAD/CAM restorations,” Journal of the American Dental Association, vol. 137, pp. 22S–31S, 2006. View at Google Scholar · View at Scopus
  7. T. Otto and D. Schneider, “Long-term clinical results of chairside Cerec CAD/CAM inlays and onlays: a case series,” International Journal of Prosthodontics, vol. 21, no. 1, pp. 53–59, 2008. View at Google Scholar · View at Scopus
  8. R. W. K. Li, T. W. Chow, and J. P. Matinlinna, “Ceramic dental biomaterials and CAD/CAM technology: state of the art,” Journal of Prosthodontic Research, vol. 58, no. 4, pp. 208–216, 2014. View at Publisher · View at Google Scholar · View at Scopus
  9. S. Reich and O. Schierz, “Chair-side generated posterior lithium disilicate crowns after 4 years,” Clinical Oral Investigations, vol. 17, no. 7, pp. 1765–1772, 2013. View at Publisher · View at Google Scholar · View at Scopus
  10. S. Pieger, A. Salman, and A. S. Bidra, “Clinical outcomes of lithium disilicate single crowns and partial fixed dental prostheses: a systematic review,” Journal of Prosthetic Dentistry, vol. 112, no. 1, pp. 22–30, 2014. View at Publisher · View at Google Scholar · View at Scopus
  11. I. Denry and J. R. Kelly, “Emerging ceramic-based materials for dentistry,” Journal of Dental Research, vol. 93, no. 12, pp. 1235–1242, 2014. View at Publisher · View at Google Scholar · View at Scopus
  12. S. Krüger, J. Deubener, C. Ritzberger, and W. Höland, “Nucleation kinetics of lithium metasilicate in ZrO2-bearing lithium disilicate glasses for dental application,” International Journal of Applied Glass Science, vol. 4, no. 1, pp. 9–19, 2013. View at Publisher · View at Google Scholar · View at Scopus
  13. V. Preis, M. Behr, S. Hahnel, and M. Rosentritt, “Influence of cementation on in vitro performance, marginal adaptation and fracture resistance of CAD/CAM-fabricated ZLS molar crowns,” Dental Materials, vol. 31, no. 11, pp. 1363–1369, 2015. View at Publisher · View at Google Scholar
  14. D. Awad, B. Stawarczyk, A. Liebermann, and N. Ilie, “Translucency of esthetic dental restorative CAD/CAM materials and composite resins with respect to thickness and surface roughness,” The Journal of Prosthetic Dentistry, vol. 113, no. 6, pp. 534–540, 2015. View at Publisher · View at Google Scholar
  15. C. D'Arcangelo, L. Vanini, G. D. Rondoni, and F. De Angelis, “Wear properties of dental ceramics and porcelains compared with human enamel,” The Journal of Prosthetic Dentistry, vol. 115, no. 3, pp. 350–355, 2016. View at Publisher · View at Google Scholar
  16. R. Frankenberger, V. E. Hartmann, M. Krech et al., “Adhesive luting of new CAD/CAM materials,” International Journal of Computerized Dentistry, vol. 18, no. 1, pp. 9–20, 2015 (German). View at Google Scholar
  17. M. O. Ahlers, G. Mörig, U. Blunck, J. Hajtó, L. Pröbster, and R. Frankenberger, “Guidelines for the preparation of CAD/CAM ceramic inlays and partial crowns,” International Journal of Computerized Dentistry, vol. 12, no. 4, pp. 309–325, 2009. View at Google Scholar · View at Scopus