Ionospheric Delay Handling for Relative Navigation by Carrier-Phase Differential GPS

Renga, A.; Tancredi, U.; Grassi, M.

doi:https://doi.org/10.1155/2015/570382

International Journal of Aerospace Engineering

On this page

Abstract Introduction Results Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2015 | Article ID 570382 | https://doi.org/10.1155/2015/570382

Ionospheric Delay Handling for Relative Navigation by Carrier-Phase Differential GPS

A. Renga,¹U. Tancredi,²and M. Grassi¹

Academic Editor: Mahmut Reyhanoglu

Received11 Apr 2015

Revised25 Jun 2015

Accepted02 Jul 2015

Published16 Jul 2015

Abstract

The paper investigates different solutions for ionospheric delay handling in high accuracy long baseline relative positioning by Carrier-Phase Differential GPS (CDGPS). Standard literature approaches are reviewed and the relevant limitations are discussed. Hence, a completely ionosphere-free approach is proposed, in which the differential ionospheric delays are cancelled out by combination of dual frequency GPS measurements. The performance of this approach is quantified over real-world spaceborne GPS data made available by the Gravity Recovery and Climate Experiment (GRACE) mission and compared to the standard solution.

1. Introduction

Carrier-Phase Differential GPS (CDGPS) is a proven technology in several fields of application. CDGPS has been already employed for relative positioning of Low Earth Orbit (LEO) satellites flying in formation [1–4], of aircraft with respect to runways [5] and for cooperative self-separation of general aviation aircraft [6]. The capability to achieve high accuracy by CDGPS is based on the possibility to exploit the integer nature of Double Difference (DD) carrier-phase ambiguities [7]. However, as the separation among the satellites increases, the correlation of ionospheric delays among the receivers decreases [8]. As a result, DD GPS observables are affected by significant errors that complicate the integer resolution task. This paper investigates the effects of different strategies for ionospheric delay compensation on the accuracy in the relative positioning of GPS receivers in LEO over long baselines. Its results can be extended, at least in principle, to other formation flying applications [9], such as those involving Very Light Jets [10] and/or Unmanned Aerial Systems [11–13].

Different approaches exist in the literature for dealing with ionospheric delays. In high accuracy, postprocessing applications with dual frequency data [14, 15], the DD ionospheric delays are estimated within a dynamic filter [16], for example, the Extended Kalman Filter (EKF), and are modelled by very simple stochastic models, typically using random walk processes in the filter’s state vector. As an alternative, delays are modelled by Lear’s model [1, 17] which allows relating the slant ionospheric delays to the Vertical Total Electron Content (VTEC) above the receivers. Even though modelling the ionospheric delays helps to increase their observability, and thus to aid in the ambiguity resolution task, Lear’s model is known to be structurally capable of reproducing actual ionospheric delays only to a limited extent [8].

It is well known that linear combinations of GPS dual frequency measurements can be used to delete the ionospheric delays to first order. When those combinations are used as an input to the EFK, it can be expected that the magnitude of the ionospheric delays does not affect the achievable relative positioning accuracy. However, the use of an ionosphere-free approach is known to complicate significantly the integer ambiguities resolution task if compared to approaches that attempt to model the ionosphere [18, 19]. Hence, the choice between model-based methods (e.g., based on Lear’s model) and ionosphere-free approaches is in general not trivial [20], depending on the relative distance between the receivers, on relative dynamics, and on the status of ionospheric activity. In this sense, the ionospheric activity plays a major role in determining the set of GPS measurements and combinations to process to improve the relative positioning accuracy.

In this paper, a completely ionosphere-free approach is pursued, in which the ionospheric delays are cancelled out by combination of dual frequency GPS measurements. Several alternative combinations are investigated based on the ionosphere-free combination of pseudorange and carrier-phase observables, but also on GRoup And PHase Ionospheric Correction (GRAPHIC) and Melbourne-Wubbena combinations and thus the best combinations are selected. Based on a relative positioning scheme previously developed by the authors [17], the performance of each approach is quantified over real-world spaceborne GPS data made available by the Gravity Recovery and Climate Experiment (GRACE) mission.

The paper is organized as follows. First the conventional approach is presented in which the ionospheric delays are estimated as part of the state vector through Lear’s model. Then ionosphere-free observables are derived from the DD observation models, and two different combinations are selected for being integrated in an ionosphere-free formulation of the EKF. The developed filter is finally tested on GRACE data.

2. Ionospheric Delays Estimated by Lear’s Model

The most common approach for handling the differential ionospheric delays in high accuracy long baseline applications is to estimate the DD ionospheric delays within the EKF modelling them using random walk processes in the state vector [14, 15]. This scheme usually integrates an EKF with an Integer Least Squares estimator based on the LAMDBA method. This approach can be not sufficiently accurate in real-time on-board implementations when accurate stochastic and dynamic models cannot be used. In such conditions, a reliable way to proceed is to model the ionospheric delays through the VTEC above the receivers by Lear’s mapping function [1, 8]. With specific reference to a formation of two satellites, this approach leads to the following state and measurement vectors:where and are the baseline and the relative velocity vectors expressed in the Earth-Centred Earth-Fixed (ECEF) reference frame and stack together the cycle ambiguities on the L1 frequency for the DD couples:where the pivot satellite, that is, the reference GPS satellite selected for calculating DD observables, is indicated with 0 for simplicity. , instead, stacks together wide-lane cycle ambiguities. In (1) indicates DD pseudorange observables and represents DD carrier-phase ones. The subscripts 1 and 2 stand for L1 and L2 GPS frequencies, respectively, whereas and subscripts refer to the receivers onboard the satellites. Finally, VTEC is the vector including the two vertical total electron contents for the two receivers. According to Lear’s model the zero difference ionospheric delay in meters for the GPS satellite and the receiver can be written as [1, 8]where is L1 carrier frequency in Hz, is the (scalar) vertical total electron content for modeling the ionospheric delay of the receiver and is expressed in number of electrons per square meter, and is the elevation of the GPS satellite with respect to the receiver .

The main advantage of Lear’s model is the capability to predict zero difference ionospheric delays, relevant to different tracked GPS satellites, as a function of a single unknown parameter (i.e., VTEC_A), which is a desirable property for navigation filters [1].

This reference model of (1)–(3) has shown satisfactory observability features [17], since it is capable of delivering good estimates of the Integer Ambiguities (IA) even in case of only 3 DD observations. However, this VTEC-based EKF has some inherent accuracy limitations, due to its inability of rejecting deviations of the true ionosphere from Lear’s model, which appear as additional error terms in the baseline estimate [8]. In what follows, the possibility is discussed of overcoming the limitations of the VTEC-based EKF by deleting the ionospheric delays through measurement combinations.

3. Ionosphere-Free Observables

Dual frequency DD carrier-phase and pseudorange observables can be combined in different ways to generate ionosphere-free measurements. The complete DD observation model is thus presented before deriving the relevant ionosphere-free observables.

3.1. DD Observation Model

The DD measurements have the following expressions [21]:where(i) is ratio between the L2 and L1 frequencies, and the and superscripts refer to the GPS satellites radiating the navigation signal;(ii), are the wavelengths of L1 and L2 signals, respectively;(iii) is the DD geometric term between the two receivers;(iv) is the DD ionospheric delay on the L1 frequency, which is denoted simply by ionospheric delay in the following;(v) is the integer ambiguity on the L1 frequency (on L2 which is analogous);(vi) is the noise term on the L1 frequency (on L2 which is analogous);(vii) is the noise term on the L1 frequency (on L2 which is analogous).Each of the four observables in (4) is assumed to be independent from the other ones. However, the DD measurements of the same kind at a certain time epoch are mutually correlated due to the presence of the pivot satellite in all the measurements. More precisely, denoting generically by the observation type, that is, , and by its standard deviation, we have

3.2. Ionospheric Free Combination

The most common combination for eliminating the ionospheric delay, referred to as Ionosphere-Free (IF) [21], is concerned with combining observations of the same type on the two carrier frequencies, exploiting the frequency dependence of the first-order ionospheric delay effect. More precisely, the IF combinations are obtained asThus, two IF observables per each DD couple out of the four measurements in (4) areThe IF observation model can be obtained combining (4), (6), and (7) which yieldsSince the observation types are assumed to be independent, assuming white Gaussian measurements noises, the IF combinations are affected by Gaussian white noise with varianceHence, the noise is increased compared to the original uncombined observations.

3.3. GRAPHIC Combinations

GRAPHIC combinations exploit the asymmetry of the ionospheric effect on group and phase propagation [22]. In practice, they combine pseudorange and carrier-phase measurements on each frequency, as follows:From the above equations, the GRAPHIC observation model and variance readwhere , indicate the noise terms of and combinations, respectively.

3.4. Melbourne-Wubbena Combinations

Melbourne-Wubbena (MW) combinations combine all four observable types for cancelling out the ionospheric delay [23, 24]. They build upon the definition of the wide and narrow lane (NL) wavelengths:where is the speed of light in vacuum. The MW combinations are obtained asand have the following observation model and variance:where represents the noise term of the combination.

4. Ionosphere-Free Relative Positioning

This section is concerned with establishing which of the measurement combinations presented in Section 3 is suitable for computing the relative position of the two receivers in long baseline applications. The measurement combinations available with no ionospheric effects are the combinations, the combinations, the GRAPHIC combinations on L1 and L2, and the MW combinations, for a total of measurements. However, the measurements are not linearly independent. In particular, each group of 5 observables per each of the DD couples can be seen as a linear transformation of the 4 uncombined measurements of (4). More precisely, the cancellation of the ionosphere from (4) can be seen as a linear projection of the 4-dimensional measurement vector onto a 3-dimensional hyperplane. This implies that no more than three linear combinations of the four dimensional vector exist being linearly independent, and thus suitable for use as measurement vector in an EKF. In addition, whatever set of three linearly independent vectors lying on the hyperplane can be used as a basis for describing all the vectors belonging to the hyperplane. Even though any of such bases would yield theoretically equivalent positioning solutions, significant differences exist in practical applications due to unmodeled systematic errors. In order to find such “best” basis, its performance in accurately estimating both the geometric term and the cycle ambiguity is analyzed. A natural indicator to evaluate the accuracy achieved by a specific measurement combination is the standard deviation (STD) of the noise affecting the measurements.

Hence, a specific analysis has been performed. Starting from different candidate noise levels for the uncombined measurements, that is, , , , and (see the first three columns in Table 1), reflecting typical performance of spaceborne GPS receivers, the expected STD for the estimation of the geometric term is derived as listed in Table 1. The rationale of this analysis is that different combinations of GPS measurements may modify, that is either amply or reduce, the uncertainty of the geometric term. Combinations able to reduce this uncertainty should be preferred for implementation in an ionosphere-free EKF. The same analysis is then repeated for the integer ambiguity on L1. Again, the smaller the uncertainty on this ambiguity, the larger the probability to correctly fix it. The results are shown in Table 2. In this case, a scale factor is introduced to represent the STD of combined measurements as a fraction of L1 cycles. In addition to this theoretical analysis, the dispersion of actual GRACE data is computed and the relevant STD is calculated (see the last row in Tables 1 and 2) for gaining further insight into the true-world accuracy of the various combinations.

According to the results presented in Tables 1 and 2, the set of measurements including , , and MW combinations is the one allowing a higher potential accuracy on both the DD geometric term and the cycle ambiguities. This set of measurements is called set “” in what follows. A potential limitation of set is that cycle ambiguities are present in all the three observation models. Hence, when the number of fixed ambiguities is smaller than three, the observation model provides no useful information to the EKF, which is thus forced to rely only on its propagation model. In this particular situation, the EKF is expected to perform poorly. To cope with this problem an additional set is considered, called set “” and made of , , and MW combinations, plus the uncombined measurement. The addition of observations allows the filter to rely on relative positioning information even when less than three cycle ambiguities are fixed.

Because the various combinations have different observation models selecting different sets of measurements affects the observability of the EKF state vector differently. The observability of the system at hand is extremely involved to be analyzed. Indeed, the dynamical system is nonlinear and evolves on a time-varying trajectory. Its linearization is thus time-varying and depends on the state estimate. The observation model is nonlinear, due to the DD geometry terms. Its linearization depends on the state trajectory, and thus it is time-varying as well. Both the dynamical and the observation models depend on an exogenous vector parameter (e.g., the absolute position of one of the receivers) [17]. Finally, both the EKF state vector and the measurements depend on the number of DD couples , which is time-varying as well. In such a condition, instead of developing a complicated observability analysis a different approach is pursued, which is based on numerically evaluating the EKF performances using both set and set as shown in the next section.

4.1. No-Iono EKF Dynamic Model

The no-iono EKF state vector is defined asConcerning the process model, the baseline dynamics is described by the nonlinear relative Keplerian model with J2 effects included. This model is equal to the one used in the VTEC-based EKF [17] and is denoted at the time epoch as follows:where is the nonlinear baseline propagation function, denotes the receiver position vector in ECEF, is the time-discrete baseline propagation matrix, is the baseline process noise vector, and indicates the mathematical expectation.

Cycle ambiguities are instead assumed to be constant. However, a small process noise might be injected, letting them be modeled as a random constant plus random walk. The model is equal to the one used in the VTEC-based EKF [17] and is denoted by ( is the -by- identity matrix)

4.2. No-Iono EKF Observation Model

The two different observation models share some common structure, which is discussed first. Then, details on each of the two models will be given. The no-iono EKF measurement vector is made of a series of measurement combinations, depending on the chosen set. Each measurement combination stacks together the combinations for each of the DD couples:The covariance matrix of has a nonsparse structure, due to the presence of the various uncombined measurements in more combinations, and because of the full covariance matrix of each of the uncombined measurements . In order to have the desired covariance matrix, , it is possible to introduce the vector that stacks the uncombined DD observations :The chosen combined measurements set can be expressed as a linear function of the uncombined measurement vector , by means of a matrix depending on the chosen set. The matrix can be obtained by applying the linear transformation:The observation model relating the EKF state to the observables is nonlinear due to the geometric term. The geometric term is independent from the chosen measurement set and thus is discussed herein. The DD geometric terms are related to the baseline by the following equations ( denotes the th GPS satellite position vector in ECEF):The nonlinear observation model and the linear delta observation model, needed for the computation of the Kalman gain in the EKF, are obtained by linearization of the propagated state vector, and it can be expressed generically asThus, at each time epoch, from the observation equations, the measurement vector is computed combining uncombined measurements. The choice of the measurement set to consider thus changes only the following: matrix for obtaining the EKF combined measurement vector from the uncombined one , nonlinear observation function, and matrix of the linearized observation model. These items are discussed in the following subsections for each measurement set.

4.2.1. Set

The matrix, the function, and the matrix take the following form:where vector stacks together DD geometric terms, is the gradient operator with respect to the baseline vector, and is the -by- null matrix.

4.2.2. Set

The matrix, the function, and the matrix take the following form:where the subscript “” is used to indicate matrix and functions relevant to set . It is worth noting that, since the ionospheric delay is cancelled and not included in the state vector, the implemented observation model for measurement is Comparing (4) to (26), it is evident that set implicitly assumes the DD ionospheric delay modelled as an additional Gaussian white noise affecting the measurements. In other words, considering that the DD ionospheric delay is only a small fraction of the total ionospheric delays, the DD observable noise is modelled as if the ionospheric delay was not time correlated but included within the white noise error. This approach resembles that one used in [7, 14] where ionospheric delays are modelled as random walk processes characterized by large process noises and correlation times in the order of the filter time step.

5. Results

The reference EKF and the no-iono solutions have been run on GRACE data. Comparisons among the solutions are performed looking at the baseline magnitude estimation error and at the capability to obtain correct estimates of the integer ambiguities. Both of them are estimated thanks to the high accuracy reference solutions, which can be computed processing GRACE data [8]. As expected, application to mild and moderate ionospheric conditions, not shown herein for brevity, suggest that the filter with Lear’s model is capable to achieve a baseline estimation error which is the half of the no-iono approach (both set and set ). This behaviour changes under strong ionospheric activity. In order to show this, DOY286 (October 13th) 2011 has been selected for the analysis, in which the two GRACE spacecrafts are separated of more than 200 km, and ionospheric activity is extremely intense. Figures 1–3 report the baseline magnitude estimation error and the IA estimation performance for the reference solution and the no-iono solutions, respectively. Specifically, only L1 estimation performance is shown because wide lane fail rates are significantly lower than those on L1.

Figure 1 shows that, under strong ionospheric activity, Lear’s model is not able to support the integer estimation, so a significant number of ambiguities is wrong and baseline magnitude estimation errors larger than 1 m occur. IA estimation performance increases notably when set is considered (see Figure 2), and the baseline estimation error reduces to decimetre scale in this case. Finally, with reference to set , it is evident that the addition of the measurements is not a successful strategy when the ionospheric activity is intense. Indeed, DD ionospheric delays dominate over measurement noise and so they cannot be modelled as additional Gaussian white noise.

6. Concluding Remarks

This paper has compared various strategies for compensating ionospheric delays in long baseline relative positioning applications for LEO spacecraft using dual-frequency CDGPS techniques. Based on a relative positioning technique previously developed by the authors, problem settings that do not require ionospheric delays estimation have been investigated. The ionosphere-free alternatives have been also compared with a reference solution making use of a standard ionospheric delay model for spaceborne applications, originally developed by Lear. Results suggest that, among the possible alternatives and under strong ionospheric activity, best performance is achieved using the observation model made of ionosphere-free combinations of carrier-phase measurements, GRAPHIC combinations on the L1 frequency, and Melbourne-Wubbena combinations. Future work will deal with the extension of these results to a more complete data set, including different levels of the ionospheric activity. The ultimate goal is the introduction of quantitative tools to guide the selection between model-based and ionosphere-free approaches depending on the ionospheric activity and the available ionospheric models.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The activities of Urbano Tancredi in this work have been carried out also with the contribution of Regione Campania in the framework of the ArchAero project, financed by the Regional Law n.5/2002 for the promotion of scientific research in Campania.

References

S. Leung and O. Montenbruck, “Real-time navigation of formation-flying spacecraft using global-positioning-system measurements,” Journal of Guidance, Control, and Dynamics, vol. 28, no. 2, pp. 226–235, 2005.
View at: Publisher Site | Google Scholar
O. Montenbruck, T. Ebinuma, E. G. Lightsey, and S. Leung, “A real-time kinematic GPS sensor for spacecraft relative navigation,” Aerospace Science and Technology, vol. 6, no. 6, pp. 435–449, 2002.
View at: Publisher Site | Google Scholar
M. L. Psiaki and S. Mohiuddin, “Modeling, analysis, and simulation of GPS carrier phase for spacecraft relative navigation,” Journal of Guidance, Control, and Dynamics, vol. 30, no. 6, pp. 1628–1639, 2007.
View at: Publisher Site | Google Scholar
F. Zuiani and M. Vasile, “Preliminary design of debris removal missions by means of simplified models for low-thrust, many-revolution transfers,” International Journal of Aerospace Engineering, vol. 2012, Article ID 836250, 22 pages, 2012.
View at: Publisher Site | Google Scholar
P. M. Xavier, A. Víctor, and S. Santiago, “Enhancing the development of a particular network of aerodromes using EGNOS,” in Proceedings of the 56th International Astronautical Congress, International Astronautical Federation, Fukouka, Japan, 2005.
View at: Google Scholar
D. J. Wing and W. B. Cotton, “For spacious skies: self-separation with ‘autonomous flight rules’ in US domestic airspace,” in Proceedings of the 11th AIAA Aviation Technology, Integration, and Operations (ATIO) Conference, September 2011.
View at: Publisher Site | Google Scholar
R. Kroes, O. Montenbruck, W. Bertiger, and P. Visser, “Precise GRACE baseline determination using GPS,” GPS Solutions, vol. 9, no. 1, pp. 21–31, 2005.
View at: Publisher Site | Google Scholar
U. Tancredi, A. Renga, and M. Grassi, “Ionospheric path delay models for spaceborne GPS receivers flying in formation with large baselines,” Advances in Space Research, vol. 48, no. 3, pp. 507–520, 2011.
View at: Publisher Site | Google Scholar
Y. Gu, G. Campa, and M. Innocenti, “Formation flight control,” International Journal of Aerospace Engineering, vol. 2011, Article ID 798981, 2 pages, 2011.
View at: Publisher Site | Google Scholar
T. Dautermann, “Civil air navigation using GNSS enhanced by wide area satellite based augmentation systems,” Progress in Aerospace Sciences, vol. 67, pp. 51–62, 2014.
View at: Publisher Site | Google Scholar
Y. Xu, W. Sun, and P. Li, “A miniature integrated navigation system for rotary-wing unmanned aerial vehicles,” International Journal of Aerospace Engineering, vol. 2014, Article ID 748940, 13 pages, 2014.
View at: Publisher Site | Google Scholar
M.-S. Huang, R. M. Narayanan, Y. Zhang, and A. Feinberg, “Tracking of noncooperative airborne targets using ADS-B signal and radar sensing,” International Journal of Aerospace Engineering, vol. 2013, Article ID 521630, 12 pages, 2013.
View at: Publisher Site | Google Scholar
L. Forlenza, G. Fasano, D. Accardo, and A. Moccia, “Flight performance analysis of an image processing algorithm for integrated sense-and-avoid systems,” International Journal of Aerospace Engineering, vol. 2012, Article ID 542165, 8 pages, 2012.
View at: Publisher Site | Google Scholar
R. Kroes, Precise relative positioning of formation flying spacecraft using GPS [Ph.D. thesis], Delft University of Technology, Delft, The Netherlands, 2006.
S.-C. Wu and Y. E. Bar-Sever, “Real-time sub-cm differential orbit determination of two low-earth orbiters with GPS bias fixing,” in Proceedings of the 19th International Technical Meeting of the Satellite Division of the Institution of Navigation (ION GNSS '06), pp. 2515–2522, Fort Worth, Tex, USA, 2006.
View at: Google Scholar
S. T. Goh, O. Abdelkhalik, and S. A. Zekavat, “Implementation of a differential geometric filter for spacecraft formation orbit estimation,” International Journal of Aerospace Engineering, vol. 2012, Article ID 910496, 13 pages, 2012.
View at: Publisher Site | Google Scholar
U. Tancredi, A. Renga, and M. Grassi, “Real-time relative positioning of spacecraft over long baselines,” Journal of Guidance, Control, and Dynamics, vol. 37, no. 1, pp. 47–58, 2014.
View at: Publisher Site | Google Scholar
T. Richert and N. El-Sheimy, “Ionospheric modeling. The key to GNSS ambiguity resolution,” GPS World, pp. 35–40, 2005.
View at: Google Scholar
O. Montenbruck, M. Wermuth, and R. Kahle, “GPS based relative navigation for the TanDEM-X mission—first flight results,” Navigation, Journal of the Institute of Navigation, vol. 58, no. 4, pp. 293–304, 2011-2012.
View at: Google Scholar
B. Li, S. Verhagen, and P. J. G. Teunissen, “Robustness of GNSS integer ambiguity resolution in the presence of atmospheric biases,” GPS Solutions, vol. 18, no. 2, pp. 283–296, 2014.
View at: Publisher Site | Google Scholar
J. Farrel and M. Barth, The Global Positioning System and Inertial Navigation, chapter 5, McGraw-Hill, New York, NY, USA, 1999.
T. P. Yunck, “Orbit determination,” in Global Positioning System: Theory and Applications, B. W. Parkinson and J. J. Spilker, Eds., vol. 2, pp. 559–592, American Institute of Aeronautics and Astronautics, Washington, DC, USA, 1996.
View at: Google Scholar
W. G. Melbourne, “The case for ranging in GPS-based geodetic systems,” in Proceedings of the 1st Intenational Symposium on Precise Positioning with the Global Positioning System, pp. 373–386, Ockville, Md, USA, 1985.
View at: Google Scholar
G. Wubbena, “Software developments for geodetic positioning with GPS using TI 4100 code and carrier measurements,” in Proceedings of the 1st Intenational Symposium on Precise positioning with the Global Positioning System, pp. 403–412, Rockville, Md, USA, 1985.
View at: Google Scholar

Copyright

Copyright © 2015 A. Renga et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2172

Downloads

1116

Citations