Abstract

A low profile, compact dual band slotted patch antenna has been designed using finite element method-based high frequency full-wave electromagnetic simulator. The proposed antenna fabricated using LPKF printed circuit board (PCB) fabrication machine on fiberglass reinforced epoxy polymer resin material substrate and the performance of the prototype has been measured in a standard far-field anechoic measurement chamber. The measured impedance bandwidths of (reflection coefficient  dB) 12.26% (14.3–16.2 GHZ), 8.24% (17.4–18.9 GHz), and 3.08% (19.2–19.8) have been achieved through the proposed antenna prototype. 5.9 dBi, 3.37 dBi, and 3.32 dBi peak gains have been measured and simulated radiation efficiencies of 80.3%, 81.9%, and 82.5% have been achieved at three resonant frequencies of 15.15 GHz, 18.2 GHz, and 19.5 GHz, respectively. Minimum gain variation, symmetric, and almost steady measured radiation pattern shows that the proposed antenna is suitable for Ku and K band satellite applications.

1. Introduction

In response to the fast growing microwave technology, there is increasing demand of compact, low profile, low cost, and light weight wireless communication module. In order for the communication terminal to be small, the antennas are needed to be low profile and compact in size [13]. Further demand of the planar patch antennas is intensified due to the attractive properties like simple geometric structure, compact, low profile, ease of integration, and fabrication characteristics with wide bandwidth. Nowadays, there is increasing demand of portable wireless communication devices and it is necessary to be dual/multiband compatible to use in different areas or countries. Due to the scarcity of bandwidth in the lower band, Ku/K band antenna design receives significant research attention recently [4, 5]. As a result, the demand of satellite-based portable communication devices is increasing remarkably, especially vehicle tracking, portable satellite station, weather forecasting, and so forth. Numerous types of patch antennas have been studied and examined by several researchers due to their excellent properties. These antennas use the monopole configuration, such as ring, elliptical, circular disc, annual ring, triangle, pentagon, and hexagonal antennas, and the dipole configuration like bow-tie antennas [611].

In order to design small and compact wireless device, it is obligatory to miniaturize the antenna size accordingly. There are numbers of requirements such as wide bandwidth, less expensive, miniature size, steady radiation patterns, and consistent gain for multiband antennas [5, 12]. Several studies have reported applications and technologies of the multiband antenna design, including dipole antenna loaded with single-cell metamaterial [13], slot-ring antenna with single- and dual-capacitive coupled patch [14], metamaterial-based planar antenna [15, 16], dual-patch elements [6], E-shape fractal antenna [17], and electromagnetic band gap (EBG) structure-based antenna [10]. A numerous concentration has given by several researchers that cutting the printed slot at the edge of radiating patch to create the desired antenna shape with targeted resonant frequency can be obtained [18, 19]. Although the resonance of the antenna not only depends on the slot but also depends on the size of the radiating element, feed line characteristics, ground plane, and so forth.

Furthermore, a significant amount of research attention has been given into microstrip patch antennas since decades. A 79 mm × 38 mm EE-H shaped L probe microstrip patch antenna has been introduced and achieved bandwidth 440 MHz with peak gain 9.5 dBi [20]. A 58 mm × 58 mm wideband dual polarized patch antenna has been proposed and obtained 1.03 GHz bandwidth with 9.3 dBi gain [21]. A 12 mm × 16 mm ultrawideband antenna with dual notched band characteristics has been offered and achieved 8.3 GHz bandwidth and 3.8 dBi maximum gain [22]. However, the reported antennas are either narrower in bandwidth, lower in gain, or larger in size compared to the proposed antenna. Nonetheless, more research concentration needs to be given to improve gain, efficiency, and bandwidth alongside the miniaturization of overall antenna size.

Therefore, a 20 mm × 15 mm compact, low profile dual band slotted patch antenna has been designed and prototyped on epoxy polymer resin-based printed circuit board (PCB). The performance of the proposed antenna prototype has been measured in a standard far-field anechoic measurement chamber. The impedance bandwidths (reflection coefficient < −10 dB) ranging from 14.3 GHz to 16.2 GHz (1.9 GHz), from 17.4 GHz to 18.9 GHz (1.5 GHz), and from 19.2 GHz to 19.8 GHz (0.6 GHz) have been measured from the proposed antenna prototype. The gains of 5.9 dBi, 3.37 dBi, and 3.32 dBi have measured and radiation efficiencies of 80.3%, 81.9%, and 82.5% have been simulated at three resonant frequencies of 15.15 GHz, 18.2 GHz, and 19.5 GHz, respectively. Radiation characteristics and surface current distribution along the radiating patch are also analyzed in this paper.

2. Antenna Design and Configurations

The proposed antenna is designed and analyzed by using finite element method-based high frequency electromagnetic field simulator [12, 23]. The design configuration starts with 20 mm (1.01 ) long and 15 mm (0.75 ) planar slotted shape radiating patch. In the proposed antenna design, is corresponding to the wavelength at the fundamental frequency 15.15 GHz. The shape is obtained by cutting 4 slots perpendicular to each other from rectangular shape. The size of the radiating patch has a major effect on the antenna performance. The overall size of the proposed antenna has been determined by using widely used mathematical formulation for patch antennas [24]. The available mathematical modeling of patch antennas is based on rectangular patch. Although due to the four cutting slots in radiating patch the overall size calculation is not straightforward as simple rectangular patch antenna, it has been optimized using HFSS optimetrics [16, 2527]. The electromagnetic wave propagates toward the endfire direction headed by the parasitic director element on the top while acting as an impedance matching element simultaneously. The design of the microstrip radiating patch element involves the estimation of its dimensions. The patch width () has a minor effect on the resonance and it has been determined by using the mathematical modeling as shown below [24]: where is the speed of light in free space and is the relative permittivity of the substrate material of the proposed antenna. The microstrip patch lies between air and the dielectric material, and, thus, the electromagnetic wave sees an effective permittivity () given by [24]:

The length of the radiating patch () is responsible for the resonant frequency and is a critical parameter in design because of the inherent narrow bandwidth of the patch. The design value for can be determined by using the following formula [24]: where is the effective permittivity of the substrate material of the proposed antenna. The additional line length on both ends of the patch length, due to the effect of fringing fields, is given by [3]

The effective patch length can be written as [20]

The proposed antenna fed by 2 mm long 1 mm wide widely used microstrip feed line to achieve impedance characteristics of 50 ohm. An SMA connector is connected at the end of the microstrip feed line. The design geometry of the proposed antenna has shown in Figure 1. The length of the radiating patch dominates bandwidth and resonance, whereas the width has minor effect. The microstrip feed line with 5 mm × 1 mm dimension is placed at the center of -axis to achieve 50 ohm impedance characteristics. The details of the proposed antenna configuration are tabulated in Table 1.

The schematic of the radiating patch of the proposed antenna has been shown in Figure 1 and the detail configuration. The proposed antenna is printed on more available, low cost, durable epoxy polymer resin material substrate with thickness of 1.6 mm, relative permittivity of 4.6, dielectric loss tangent of 0.02, using in-house S63 PCB prototyping machine from LPKF, Garbsen, Germany. At the end of the microstrip feed line, SMA connector is connected. The fabricated prototype of the proposed antenna is illustrated in Figure 2.

3. Measurement Environment

The prototype of the proposed antenna has been measured in a standard far-field testing environment [18, 28]. A rectangular shape 5.5 × 4.5 m2 and a 4 m height anechoic measurement chamber were used to measure the result parameter of the proposed antenna prototype. A double ridge guide horn antenna has been used as reference antenna. Pyramidal shape electrically thick foam absorber with less than −60 dB reflectivity at normal incidence has been used on the wall, celling and floor. A turn table of 1.2 m diameter has been used to rotate the measuring antenna with specification, 1 rpm rotation speed; 360° rotation angle connected with 10 meter cable between controllers. An Agilent PNA-series vector network analyzer (Agilent E8362C) ranging up to 20 GHz has been used for measurement procedure. Figure 3 shows the photograph of the anechoic antenna measurement chamber.

4. Performance Result and Discussion

The performance results of the proposed antenna prototype are deliberated in this section. The measured and simulated reflection coefficients are shown in Figure 4. It can be clearly seen that the impedance bandwidth (reflection coefficient < −10 dB) ranging from 14.3 GHz to 16.2 GHz (1.9 GHz), from 17.4 GHz to 18.9 GHz (1.5 GHz), and from 19.3 GHz to 19.8 GHz (0.6 GHz) was measured from the proposed antenna prototype. The slight inconsistency observed between simulated and measured reflection coefficients could be due to SMA soldering effect or the loss introduced by the cable between antenna under test and the controller. However, the measurement setup has been calibrated using Agilent automatic calibration tools. The simulated and measured gain of the proposed antenna has been shown in Figure 5. Average gains of 5.6 dBi, 3.5 dBi, and 3.1 dBi have been measured for first, second, and third bands correspondingly. For the gain measurement of the proposed antenna, three antenna measurement systems have been used with two identical horn antennas [29, 30].

The radiation efficiency of the proposed antenna is shown in Figure 6. It exhibits 80.3%, 81.9%, and 82.5% at three resonant frequencies of 15.15 GHz, 18.2 GHz, and 19.5 GHz, respectively, with minimum variation. The measured almost steady radiation pattern of the proposed antenna prototype is shown in Figure 7. The cross polarization effects of both and planes are lower than copolarization. Figure 8 shows the Smith chart of the proposed antenna. The VSWR and impedance () characteristics can be validated from the Smith chart. It can be clearly observed that the three resonant frequencies are in the VSWR 2 : 1 circle.

5. Conclusion

A 20 mm × 15 mm slotted patch antenna was designed and fabricated on the epoxy polymer resin composite material substrate for dual band applications. The measured performance results of the proposed antenna exhibit the impedance bandwidth (reflection coefficient < −10 dB) ranging from 14.3 GHz to 16.2 GHz (12.26%), from 17.4 GHz to 18.9 GHz (8.24%), and from 19.3 GHz to 19.8 GHz (3.08%). Average gains of 5.6 dBi, 3.5 dBi, and 3.1 dBi have been measured at first, second, and third bands, respectively. Radiation efficiencies of 80.3%, 81.9%, and 82.5% have been simulated at three resonant frequencies of 15.15 GHz, 18.2 GHz, and 19.5 GHz correspondingly. The measured almost steady omnidirectional radiation pattern shows that the proposed antenna is suitable for Ku and K band applications.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.