Frequency Diverse Array MIMO Radar Adaptive Beamforming with Range-Dependent Interference Suppression in Target Localization

Gao, Kuandong; Shao, Huaizong; Cai, Jingye; Chen, Hui; Wang, Wen-Qin

doi:https://doi.org/10.1155/2015/358582

International Journal of Antennas and Propagation

On this page

Abstract Introduction Conclusion References Copyright Related Articles

Research Article | Open Access

Volume 2015 | Article ID 358582 | https://doi.org/10.1155/2015/358582

Frequency Diverse Array MIMO Radar Adaptive Beamforming with Range-Dependent Interference Suppression in Target Localization

Kuandong Gao,¹Huaizong Shao,¹Jingye Cai,¹Hui Chen,¹and Wen-Qin Wang¹

Academic Editor: Jaume Anguera

Received01 Feb 2015

Accepted10 Sept 2015

Published11 Oct 2015

Abstract

Conventional multiple-input and multiple-output (MIMO) radar is a flexible technique which enjoys the advantages of phased-array radar without sacrificing its main advantages. However, due to its range-independent directivity, MIMO radar cannot mitigate nondesirable range-dependent interferences. In this paper, we propose a range-dependent interference suppression approach via frequency diverse array (FDA) MIMO radar, which offers a beamforming-based solution to suppress range-dependent interferences and thus yields much better DOA estimation performance than conventional MIMO radar. More importantly, the interferences located at the same angle but different ranges can be effectively suppressed by the range-dependent beamforming, which cannot be achieved by conventional MIMO radar. The beamforming performance as compared to conventional MIMO radar is examined by analyzing the signal-to-interference-plus-noise ratio (SINR). The Cramér-Rao lower bound (CRLB) is also derived. Numerical results show that the proposed method can efficiently suppress range-dependent interferences and identify range-dependent targets. It is particularly useful in suppressing the undesired strong interferences with equal angle of the desired targets.

1. Introduction

Multiple-input and multiple-output (MIMO) radar has received much attention in recent years. But for conventional colocated MIMO radar, the array manifold caused by time delay only depends on the angle and thus has difficulty in distinguishing the targets and interferences that have the same angle but different ranges by general beamforming techniques [1–3]. Moreover, the localization performance will also be significantly degraded [4, 5] with the targets with the same angle but different ranges. The conventional MIMO radar cannot distinguish range-dependent targets. According to the radar ambiguity function, the range and velocity of a target cannot be simultaneously estimated. Several methods have been suggested to solve these problems. A potential solution is using multiple distributed receivers. But it requires clock synchronization due to separated receivers, which is a technical challenge.

Frequency diverse array (FDA) radar proposed in [6–8] can suppress range-dependent interferences. Different from phased-array radar, a small frequency increment, as compared to the carrier frequency, is applied between FDA elements [9, 10]. This small frequency increment results in a range-angle-dependent beampattern [11–13]. The time and angle periodicity of FDA beampattern was analyzed in [14]. A linear FDA was proposed in [15] for forward-looking radar ground moving target indication. The application of FDA for bistatic radar system was analyzed in [16]. And the imaging of FDA radar was investigated in [17–19]. In [20], we have derived the FDA Cramér-Rao lower bounds (CRLBs) for estimating direction, range, and velocity. Although FDA has drawn much attention in antenna and radar areas, the existing literature concentrates on FDA conceptual system design [21, 22]. Furthermore, most of the FDA MIMO radar literature focuses on beamforming algorithm [23–25], and little work on target localization application and its performance analysis has been reported [26, 27].

In this paper, we design the FDA MIMO radar for range-dependent beamforming and target localization. Our proposed approach exploits jointly the advantages of FDA and MIMO techniques. The advantages of FDA MIMO radar as compared to conventional MIMO radar are investigated. Furthermore, the FDA MIMO radar performance is evaluated by the corresponding transmitting-receiving beampattern, and output signal-to-interference-plus-noise ratio (SINR) is also examined. The contributions of this paper can be summarized as follows. (i) We formulate the data model of FDA MIMO radar. (ii) Range-dependent interferences/targets with the same angle of the targets are suppressed/detected by the FDA MIMO adaptive beamformer. (iii) The CRLB of FDA MIMO radar is derived, along with extensive numerical results. (iv) We derive and verify the resolution probability of FDA MIMO radar localization.

The rest of this paper is organized as follows. In Section 2, we formulate the FDA MIMO radar data model. And we present an FDA MIMO radar adaptive beamforming approach with range-dependent interference suppression in Section 3. In Section 4, the multiple signal classification (MUSIC) algorithm is employed for target localization in angle-range dimension. Simulation results are provided in Section 5. Finally, conclusions are drawn in Section 6.

2. Data Model of FDA MIMO Radar

Consider an FDA MIMO radar equipped with colocated transmitting elements and colocated receiving elements. Assume the transmit and receiving arrays are closely located, so that a target located in far field can be seen by both of them at the same spatial angle. Each transmitting element sends out a distinct omnidirectional waveform , and . Let be the vector collecting all these waveforms. The baseband equivalent model, in complex-valued form, of the transmitted signals from the th transmit element can be expressed aswhereis the th entry of the transmit steering vector with being the frequency increment [25] while is the element space, is the carrier wavelength, denotes the light speed, and and are the target angle and range, respectively. As a comparison, (3) gives the th entry of the steering vector for a phased array, which is not related to the range variable :The FDA MIMO radar transmit steering vector depends on both the range and the angle, whereas that of conventional MIMO radar depends only on the angle. Therefore, the interferences with the same angle of the targets cannot be suppressed by conventional MIMO radar but may be resolved by the FDA MIMO radar.

For a position with angle and range , the phase difference between the two signals transmitted by two adjacent elements isThereby, the transmit steering vector is given byAfter being reflected by the targets or interferences, the signals are received by the colocated receiving array. Taking the first element as a reference, the phase difference of the signals received by two adjacent elements isSimilarly, the receiving steering vector iswhere denotes the transpose operator. The phase difference of the transmit steering vector becomeswhere is caused by reflected range. Therefore, the new transmit steering vector at the receiving array is given bySuppose there is a target located at the position along with multiple interferences located at . receiving complex vector of the receiver observations can be written aswhere stands for the complex amplitude of the target and represents the complex amplitude of the th interference source and is additive zero-mean white Gaussian noise term with covariance matrix , with being the noise power. Note that is the slow time and is the fast time. Since is orthogonal, the received signals can be processed by a matched filter, which outputs an matrix:where and denote the matrix inverse operator and conjugate transpose operator, respectively, and denotes summation operator. Furthermore, it is easy to show that is independent and identically distributed (i.i.d.) Gaussian entries with zero mean and variance . Stacking the columns of , we obtain an virtual data vectorwhere denotes vectorization operator and , anddenotes the joint transmit-receiving virtual steering vector, in which stands for the Kronecker product. The interference-plus-noise covariance matrix can be expressed aswhere denotes the index of interferences and is the averaged power.

3. Adaptive Beamforming and SINR Analysis for FDA MIMO Radar

In this section, we consider the adaptive beamforming which can suppress the range-dependent interferences having the same angle but different ranges from that of targets. The performance is examined in terms of the output signal-to-interference-plus-noise ratio (SINR). For discussion convenience, we rewrite the output of matched filter as follows:To suppress the interferences, the conventional MVDR beamformer for a target located at is employed byThe first term denotes the interference power minimization, and the second term stands for ensuring the target signal without distortion. The weight vector can be solved asHowever, the MVDR beamformer does not make constraints on the sidelobe. In order to suppress the sidelobes, (17) can be reformulated aswhere is the position of the sidelobe and is the sidelobe level. Accordingly, the beampattern is given by

The SINR can be calculated bywhere and are the target signal and interference signals averaged power, respectively, and the diagonal is the noise covariance matrix.

It is well known that inverse of an Hermitian symmetric matrix requires operations. For the FDA MIMO radar, since is an vector, computing and requires and operations, respectively [28]. Then, computation complexity is . The traditional MIMO radar has the same computation complexity. However, traditional MIMO radar has equal transmit and receiving array spacing, and its computing complexity will be [29].

4. FDA MIMO Radar Localization Performance and Resolution Probability Analysis

In this section, we analyze the FDA MIMO radar localization performances in terms of CRLB and resolution probability. The FDA MIMO radar localization can estimate not only target angles, but also target ranges. We can regard both target and interferences as sources. In this case, (13) can be reformulated aswhere the subscript “” denotes the number index of targets. Defining , we can getThe first column is the receiving steering vector given in (9). Thus, we can estimate the target angle through the received signals. Similarly, the range can also be estimated.

According to (22), the covariance matrix can be obtained bywhere is the receiving steering matrix for multiple signals with being the number of targets and . For independent target signals and noise, can be reformulated as where and are the unitary matrices of signal and noise subspaces, respectively, denotes the target signal power, and is the unit matrix. The rank of is equal to the number of targets. Once the number of signals is obtained, the sizes of and are known accordingly. According to the MUSIC principle, the targets can be localized by searching the following peaks:

The eigenvalue decomposition (EVD) of an Hermitian symmetric matrix requires a computation complexity of [28]. According to Section 3, the total computation complexity of an FDA MIMO radar is , which is the same as that of a traditional MIMO radar. When the transmit and receiving arrays have the same element spacing, the computation complexity will be [29].

To derive the CRLB, we rewrite (10) as where with denoting a diagonal matrix. Note that, for notation convenience, has been included in . The unknown parameter vector to be estimated is then given by where , , , and are the real part and image part of , respectively. We divide into deterministic and random components, where are the deterministic parameters and are random components. The Fisher information matrix (FIM) with respect to is where is the noise covariance matrix, denotes the real part, and stands for the trace of a matrix. Equation (31) can be written as where the facts that and are used. Due to the fact that , we can get We take a derivative with respect to where represents the th column of the unit matrix and denotes the derivation of (similar for ). We take also a derivative with respect to , We then have where the fact that is utilized. Define The FIM with respect to part can be calculated by Similarly, we have where and are the real and imaginary part of reflection coefficient , respectively. Defining and , we can get [30] Therefore, the FIM of FDA MIMO radar is derived asFinally, the CRLBs with respect to and are the two diagonal elements of the inverse of the FIM: where is the inverse of and is the element at the th row and th column of the matrix. Since matrices and depend on both range and , the CRLBs are influenced by .

Furthermore, we use the resolution probability defined as follows to compare the localization performance. Two targets can be resolved only when the following relation is achieved: where and are the true directions.

5. Simulation Results

Suppose the following simulation parameters: , GHz, , m/s, KHz, , dB, and . The additive noise is modeled as complex Gaussian zero-mean spatially and temporally white random sequences.

Example 1 (adaptive beamforming and performance analysis). In the first example, one target of interest and multiple interferences are located at = (10°, 10 km) and = (10°, 6.5~9 km), respectively.

Figure 1(a) gives the adaptive beampattern of conventional MIMO radar. Obviously, it cannot suppress the interferences having the same angle as the targets shown in Figure 2. In this case, the interferences will degrade the SINR performance. In contrast, the beampattern mainlobe of FDA MIMO radar can be steered to suppress range-dependent interferences, as shown in Figure 1(b) and Figure 2. The FDA MIMO radar beampattern has zero nullings at the interference locations and, thus, the sidelobes are significantly suppressed.

(a)

(b)

We also examined the adaptive beamformer output SINR versus input SINR. In the first case, we assume that the target and interference have the same angle but different ranges. Figure 3(a) shows the comparative beamforming performance. It is noticed that FDA MIMO radar has a much higher output SINR than conventional MIMO radar. In the second case, the target and interference are at angles and , respectively. It is seen from Figure 3(b) that the output SINR of FDA MIMO radar is equivalent to that of phased MIMO radar. Consequently, FDA MIMO radar outperforms conventional MIMO radar in interference suppression.

(a)

(b)

Example 2 (localization and performance analysis). Consider four targets with locations (, 8 km), (, 8 km), (, 10 km), and (, 10 km) and dB. Figure 4 compares the localization results. Since conventional MIMO radar can only estimate target angles, there are only two curves for conventional MIMO radar. Consequently, conventional MIMO radar fails to resolve the four targets completely.

(a)

(b)

In contrast, the four targets can be easily identified by the FDA MIMO radar, as shown in Figure 4(a). Furthermore, to clearly compare the performance, the amplitude spectrum profile cut at angle is given in Figure 5. It shows that the target ranges are correctly estimated by the FDA MIMO radar.

Figure 6 compares the CRLB as a function of SNR. The FDA MIMO radar steering vector depends on . Figure 6(a) gives the CRLB for angle estimation at different . It is seen that CRLB for holds as increases, whereas CRLB for range decreases as increases, as shown in Figure 6(b).

(a)

(b)

Figures 7(a) and 7(b) show the mean square error (MSE) [31] and CRLB on angle and range estimations versus SNR, respectively. Note that the MSEs are computed based on 100 independent Monte Carlo simulation runs. In Figure 7(a), the conventional MIMO radar has two target signals having the same angle whereas the FDA MIMO radar MSE is obtained by considering only one target. Therefore, the previous result outperforms that of the FDA MIMO radar in angle estimation. Nevertheless, it can be seen that the proposed approach gives a satisfactory estimation performance.

(a)

(b)

Finally, the resolution probability performances are compared in Figure 8(a). It can be seen that FDA MIMO radar still outperforms conventional MIMO radar. Figure 8(b) shows the resolution probability versus . Since , if increases, the range will decrease. Hence, the resolution probability will decrease along with the decrease of for FDA MIMO radar.

(a)

(b)

6. Conclusion

In this paper, we proposed an FDA MIMO adaptive beamforming and localization scheme for range-dependent targets and interferences with the same angle but different ranges. The FDA MIMO radar provides a promising range-dependent beampattern, which is particularly valuable for suppressing range-dependent interferences. The FDA MIMO radar has higher output SINR than the conventional MIMO radar. Besides, the ranges and angles of targets can be solely estimated with MUSIC-based algorithm. This conclusion is also validated by the CRLB and MSE for FDA MIMO radar which are also analyzed to examine the estimation performance comparisons.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgment

This work was supported in part by the Program for New Century Excellent.

References

B. D. Van Veen and K. M. Buckley, “Beamforming: a versatile approach to spatial filtering,” IEEE ASSP Magazine, vol. 5, no. 2, pp. 4–24, 1988.
View at: Publisher Site | Google Scholar
E. Tuncer and B. Freidlander, Classical and Modern Direction-of-Arrival Estimation, Elsevier, New York, NY, USA, 2009.
J. Ding, H. Chen, H. Wang, X. Li, and Z. Zhuang, “Low-grazing angle detection in compound-gaussian clutter with hybrid MIMO radar,” International Journal of Antennas and Propagation, vol. 2013, Article ID 374342, 8 pages, 2013.
View at: Publisher Site | Google Scholar
Y. A. S. Dama, R. A. Abd-Alhameed, S. M. R. Jones et al., “An envelope correlation formula for (N, N) MIMO antenna arrays using input scattering parameters, and including power losses,” International Journal of Antennas and Propagation, vol. 2011, Article ID 421691, 7 pages, 2011.
View at: Publisher Site | Google Scholar
C. Yunhe, Z. Zijing, W. Shenghua, and D. Fengzhou, “Direction finding for bistatic MIMO radar with uniform circular array,” International Journal of Antennas and Propagation, vol. 2013, Article ID 674878, 6 pages, 2013.
View at: Publisher Site | Google Scholar
P. Antonik, M. C. Wicks, H. D. Griffiths, and C. J. Baker, “Frequency diverse array radars,” in Proceedings of the IEEE Radar Conference, pp. 215–217, Verona, NY, USA, April 2006.
View at: Publisher Site | Google Scholar
M. C. Wicks and P. Antonik, “Frequency diverse array with independent modulation of frequency, amplitude, and phase,” U.S.A Patent 7,319,427, January 2008.
View at: Google Scholar
P. Antonik and M. C. Wicks, “Method and apparatus for simultaneous synthetic aperture and moving target indication,” U.S.A Patent, application 20080129584, June 2008.
View at: Google Scholar
P. Antonik, M. C. Wicks, H. D. Griffiths, and C. J. Baker, “Multi-mission multi-mode waveform diversity,” in Proceedings of the IEEE Radar Conference, pp. 580–582, IEEE, Verona, NY, USA, April 2006.
View at: Publisher Site | Google Scholar
P. Antonik and M. C. Wicks, “Method and apparatus for a frequency diverse array,” U.S.A Patent 7.511,665B2, March 2009.
View at: Google Scholar
P. Antonik, An investigation of a frequency diverse array [Ph.D. dissertation], University College London, London, UK, 2009.
A. Aytun, Frequency diverse array radar [M.S. thesis], Naval Postgraduate School, 2010.
S. Brady, Frequency diverse array radar: signal characterization and measurement accuracy [M.S. thesis], Air Force Institute of Technology, 2010.
M. Secmen, S. Demir, A. Hizal, and T. Eker, “Frequency diverse array antenna with periodic time modulated pattern in range and angle,” in Proceedings of the IEEE Radar Conference, pp. 427–430, Boston, Mass, USA, April 2007.
View at: Publisher Site | Google Scholar
P. Baizert, T. B. Hale, M. A. Temple, and M. C. Wicks, “Forward-looking radar GMTI benefits using a linear frequency diverse array,” Electronics Letters, vol. 42, no. 22, pp. 1311–1312, 2006.
View at: Publisher Site | Google Scholar
P. F. Sammartino and C. J. Baker, “The frequency diverse bistatic system,” in Proceedings of the International Waveform Diversity and Design Conference (WDD '09), pp. 155–159, Orlando, Fla, USA, February 2009.
View at: Publisher Site | Google Scholar
J. Farooq, M. A. Temple, and M. A. Saville, “Application of frequency diverse arrays to synthetic aperture radar imaging,” in Proceedings of the International Conference on Electromagnetics in Advanced Applications (ICEAA '07), pp. 447–449, Torino, Italy, September 2007.
View at: Publisher Site | Google Scholar
J. Farooq, M. A. Temple, and M. A. Saville, “Exploiting frequency diverse array processing to improve SAR image resolution,” in Proceedings of the IEEE Radar Conference (RADAR '08), pp. 1–5, IEEE, Rome, Italy, May 2008.
View at: Publisher Site | Google Scholar
J. Farooq, Frequency diversity for improving synthetic aperture radar imaging [Ph.D. thesis], Air Force Institute of Technology, 2009.
Y. Wang, W.-Q. Wang, and H. Shao, “Frequency diverse array radar cramér-rao lower bounds for estimating direction, range, and velocity,” International Journal of Antennas and Propagation, vol. 2014, Article ID 830869, 10 pages, 2014.
View at: Publisher Site | Google Scholar
V. Ravenni, “Performance evaluations of frequency diversity radar system,” in Proceedings of the 4th European Radar Conference, pp. 436–439, Munich, Germany, October 2007.
View at: Publisher Site | Google Scholar
W.-Q. Wang, “Range-angle dependent transmit beampattern synthesis for linear frequency diverse arrays,” IEEE Transactions on Antennas and Propagation, vol. 61, no. 8, pp. 4073–4081, 2013.
View at: Publisher Site | Google Scholar | MathSciNet
P. F. Sammartino, C. J. Baker, and H. D. Griffiths, “Frequency diverse MIMO techniques for radar,” IEEE Transactions on Aerospace and Electronic Systems, vol. 49, no. 1, pp. 201–222, 2013.
View at: Publisher Site | Google Scholar
L. Zhuang and X. Z. Liu, “Application of frequency diversity to suppress grating lobes in coherent MIMO radar with separated subapertures,” EURASIP Journal on Advances in Signal Processing, vol. 2009, Article ID 481792, 10 pages, 2009.
View at: Publisher Site | Google Scholar
W.-Q. Wang, “Phased-MIMO radar with frequency diversity for range-dependent beamforming,” IEEE Sensors Journal, vol. 13, no. 4, pp. 1320–1328, 2013.
View at: Publisher Site | Google Scholar
W.-Q. Wang and H. Shao, “Range-angle localization of targets by a double-pulse frequency diverse array radar,” IEEE Journal on Selected Topics in Signal Processing, vol. 8, no. 1, pp. 106–114, 2013.
View at: Publisher Site | Google Scholar
W.-Q. Wang and H. C. So, “Transmit subaperturing for range and angle estimation in frequency diverse array radar,” IEEE Transactions on Signal Processing, vol. 62, no. 8, pp. 2000–2011, 2014.
View at: Publisher Site | Google Scholar | MathSciNet
S. D. Somasundaram, N. H. Parsons, P. Li, and R. C. de Lamare, “Reduced-dimension robust capon beamforming using Krylov-subspace techniques,” IEEE Transactions on Aerospace and Electronic Systems, vol. 51, no. 1, pp. 270–289, 2015.
View at: Publisher Site | Google Scholar
K. W. Forsythe, D. W. Bliss, and G. S. Fawcett, “Multiple-input multiple-output (MIMO) radar: performance issues,” in Proceedings of the 38th Asilomar Conference on Signals, Systems and Computers, vol. 1, pp. 310–315, IEEE, Pacific Grove, Calif, USA, November 2004.
View at: Publisher Site | Google Scholar
J. Li, L. Xu, P. Stoica, K. W. Forsythe, and D. W. Bliss, “Range compression and waveform optimization for MIMO radar: a Cramér-Rao bound based study,” IEEE Transactions on Signal Processing, vol. 56, no. 1, pp. 218–232, 2008.
View at: Publisher Site | Google Scholar | MathSciNet
L. W. Nolte, S. C. Lee, and S.-C. Liu, “On performance of array signal processing,” IEEE Journal of Oceanic Engineering, vol. 12, no. 1, pp. 148–154, 1987.
View at: Google Scholar

Copyright

Copyright © 2015 Kuandong Gao et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1599

Downloads

1511

Citations