Degradation of Abamectin Using the Photo-Fenton Process

Matos, Thiago Augusto de Freitas; Dias, Alexandra Lemos Nunes; Reis, Amanda Di Piazza; Silva, Milady Renata Apolinário da; Kondo, Márcia Matiko

doi:https://doi.org/10.1155/2012/915724

International Journal of Chemical Engineering

On this page

Abstract Introduction Experimental Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Special Issue

Recent Advances in Valorization Methods of Inorganic/Organic Solid, Liquid, and Gas Wastes

View this Special Issue

Research Article | Open Access

Volume 2012 | Article ID 915724 | https://doi.org/10.1155/2012/915724

Degradation of Abamectin Using the Photo-Fenton Process

Thiago Augusto de Freitas Matos,¹Alexandra Lemos Nunes Dias,¹Amanda Di Piazza Reis,¹Milady Renata Apolinário da Silva,¹and Márcia Matiko Kondo¹

Academic Editor: Licínio M. Gando-Ferreira

Received15 Oct 2011

Revised11 Jan 2012

Accepted16 Jan 2012

Published25 Mar 2012

Abstract

The cultivation of strawberries generally requires substantial use of pesticides, and abamectin is the active principle of one of those most commonly employed. Conventional water treatment does not remove pesticides efficiently, so there is a need to investigate alternative procedures. The use of advanced oxidation processes (AOPs) can achieve good results in removal of toxic organic compounds present in aqueous solutions. The photo-Fenton process, one example of an AOP, was employed to study the degradation of abamectin. Results showed that when natural water samples contaminated with abamectin were treated using the photo-Fenton process, 70% of the initial amount of the compound was removed within 60 minutes of UV irradiation, and 60% mineralization was observed after 180 minutes of reaction.

1. Introduction

Biocides are one of the most important classes of compounds introduced into surface waters by human activities [1]. They are widely used in agriculture and can contaminate rivers and other water bodies due to transport from cultivated areas [2–5]. Although the pesticide industry has developed new compounds that are more effective, even at lower concentrations, and that present lower environmental impacts [6], the misuse of such pesticides can pose considerable toxicity risks to operators, consumers, and the wider environment [7].

The cultivation of strawberries uses large amounts of pesticides. One of the most commonly employed is Vertimec 18 EC, which contains 1.8% (w/v) of abamectin, the active principle. Abamectin belongs to the avermectin group and has the molecular formula C₄₈H₇₂O₁₄ (avermectin B1a) + C₄₇H₇₀O₁₄ (avermectin B1b). It is used primarily as a biocide. Abamectin is a toxic chemical and can be fatal if inhaled, ingested, or absorbed by the skin. It causes skin and eye irritation, and at high doses can cause damage to the central nervous system (CAS no., 71751-41-2). The substance is also highly toxic to fish and aquatic invertebrates. The maximum acceptable daily intake (ADI) is 0.01 mg kg⁻¹ body weight, and the maximum residue limit is 0.02 mg kg⁻¹ of the commercial product [8].

Effluents containing biocides cannot usually be treated efficiently using biological techniques, since the effluents are toxic to the microorganisms involved so that the biodegradation efficiency is reduced [9].

An alternative treatment that has been investigated is based on the use of advanced oxidation processes (AOPs), which are very efficient for the removal of potentially toxic organic compounds from water systems. In AOPs, hydroxyl radicals are formed as highly reactive intermediates, and can mineralize organic compounds to H₂O, CO₂, and mineral acids [10–13].

The photo-Fenton process, an AOP, has attracted considerable interest due to its high efficiency in producing hydroxyl radicals during H₂O₂ decomposition catalysed by Fe²⁺ in acid solution under UV irradiation (1) and (2) [14]. Advantages of this process include the ability to use relatively low-cost reagents, and solar irradiation as the UV source. At the end of the process, the iron ions present can be precipitated by increasing the pH, while the H₂O₂ is consumed during the reaction [15]:

The generated can degrade organic pollutants present in aqueous solutions. Parameters such as pH and reagent concentration ratios must be controlled, in order to enhance the efficiency of the degradation process. The optimum pH range for the Fenton and photo-Fenton processes is 2.5–3.0 [16, 17]. The use of an excess amount of H₂O₂ can reduce the efficiency, since hydrogen peroxide can scavenge, generating which has a lower reducing potential than the hydroxyl radical [18, 19].

Fenton and photo-Fenton processes have been successfully employed to treat a variety of effluents containing compounds such as dyes [20], antibiotics [21, 22], landfill leachates [23], and emerging contaminants [24].

The Federal University of Itajubá (Universidade Federal de Itajubá) is located in one of the major strawberry cultivation areas of Brazil. The objective of the present paper was to investigate the degradation efficiency of abamectin using the photo-Fenton process with UV irradiation.

2. Experimental

2.1. Pesticide Solutions

Abamectin solutions were prepared from the commercially available pesticide, in distilled water at a concentration of 9 mg L⁻¹ (400 mg L⁻¹ TOC). This concentration is the same as that used by farmers during strawberry cultivation.

2.2. Photo-Fenton Process

Iron nitrate (0.5 mmol L⁻¹) was added to the abamectin solution, and the pH was adjusted to 2.5 using 1.0 mol L⁻¹ H₂SO₄. The photoreactor consisted of an UV lamp (Hg, 125 W, λ_max = 365 nm), inserted into a double jacket whereby the system could be cooled by water recirculation, and was immersed in the reaction solution. 6.0 mmol L⁻¹ of H₂O₂ was added to the abamectin solution, and the lamp was turned on to start the reaction (17 mW cm⁻², as measured by a Cole-Parmer radiometer, series 9811). Samples were withdrawn at predetermined intervals, over periods of 60 or 180 minutes. To halt the Fenton reaction, the pH was raised to pH 10 using 6.0 mol L⁻¹ NaOH, in order to precipitate iron hydroxide. The supernatant was separated by centrifugation and used for the different chemical analyses. The choice of pH value and the H₂O₂ and Fe³⁺ concentrations was based on previous work that used the Fenton reaction to treat another herbicide [25–27].

Natural water samples from the José Pereira stream (22°24′50″S and 45°24′02″W, in WGS 84 datum) were also spiked with the same concentration of abamectin and irradiated under the conditions already described. The objective of these tests was to study the efficiency of the Fenton reaction under conditions more representative of those arising from agricultural contamination.

Experiments were also performed without irradiation (Fenton process), using the H₂O₂/UV advanced oxidative process. Control experiments using UV alone (direct photolysis), H₂O₂ alone, and iron alone with UV were conducted in order to evaluate the influence of each parameter on the degradation process.

2.3. Abamectin Quantification

Abamectin was quantified by GC/FID using a Varian Model CP 3380 instrument equipped with an AB-5 column (25 m0.25 mm0.25 μm). Aliquots (1 μL) of the eluted samples were injected into the GC. The operating conditions of the oven were an initial temperature of 50°C for 1 minute, a ramp to 200°C at 15°C min⁻¹, and a final hold at 200°C for 1 minute. The injector temperature was 240°C, and the FID detector temperature was 300°C. All samples were injected 4 times, and the results were calculated as averages. All experiments were performed in triplicate.

Analytical grade abamectin (Sigma-Aldrich) was used to generate the calibration curve. The detection limit (DL) and quantification limit (QL) were calculated using the ratio of the standard deviation (s) and the slope (S) of the calibration curve (3) and (4) [28]:

Since the abamectin solution used for the degradation experiments was prepared from a commercially available pesticide that contained other compounds, it was necessary to separate the abamectin from the aqueous solutions prior to the chromatographic analyses. This was achieved by solid phase extraction using Waters Sep-Pak C₁₈ cartridges [29]. After the degradation process, the samples were centrifuged in order to separate out the iron precipitate. The supernatant (50 mL) was passed through the Sep-Pak cartridge at a flow rate of 1.66 mL min⁻¹, using a glass syringe. The abamectin retained in the cartridge was then eluted with an aqueous solution containing 85% methanol. This extract was used for abamectin quantification using GC.

2.4. Statistical Analysis

The statistical analysis employed R software and its complement Tinn-R [30] and considered the data to be randomly distributed. The residuals of the data were determined, together with the homogeneity of the variances. The multiple comparison analysis used the Tukey test (at a 5% significance level).

2.5. Hydrogen Peroxide Determination

The hydrogen peroxide concentration was monitored spectrophotometrically using the metavanadate method [31].

2.6. Total Organic Carbon (TOC)

The mineralization of organic material in the solution during the photodegradation was monitored by quantifying total organic carbon (TOC) using a carbon analyser (TOC 5000A, Shimadzu). These analyses were performed in the laboratory of the LAPOA group, at the Institute of Chemistry, UNESP (Araraquara, São Paulo, Brazil).

3. Results and Discussion

Determination of abamectin is usually performed by liquid chromatography [32–35]. At present there are no reports in the literature concerning analysis of the compound by gas chromatography, so that a new method therefore needed to be developed. Injection of a methanolic solution of abamectin showed that it eluted at a retention time of 5.7 minutes. Validation of an analytical method involving a separation technique (such as GC) requires determination of parameters including the linearity of the analytical curve, the DL, and the QL [28]. The calibration curve obtained here showed good linearity, with a high correlation coefficient (0.9988). The calculated detection and quantification limits were 0.0168 mg L⁻¹ and 0.0511 mg L⁻¹, respectively, which are low compared to the initial pesticide concentration. Repeatable quantification of abamectin was achieved after separation using Sep-Pak cartridges, showing that the method was also selective. These results demonstrated that the technique used to quantify abamectin met the requirements of the present paper, which were to identify abamectin and monitor its concentration with precision during the photo-Fenton treatment process.

3.1. Control Experiments

In order to understand the influence of the different experimental variables on the degradation of abamectin, experiments were performed using each variable individually. Combinations of variables (such as iron and UV) were also employed. Figure 1 shows the comparative results obtained for these tests.

Abamectin was destroyed by direct photolysis, with 39% removal after 1 hour of irradiation (Figure 1). This result indicates that the pesticide could be photodegraded if present in surface water within the photic zone. Mushtaq et al. [36] showed that avermectin, the chemical group to which abamectin belongs, was also degraded by direct photolysis in natural water after 22 days of solar irradiation. Nevertheless, direct photolysis will not occur in the natural environment when the compound is absorbed in the sediment, or when it is present below the photic zone.

Kamel et al. [37] studied the degradation of abamectin in Saudi Arabian soil. Removal rates of 66% and 88% were observed after 7 and 14 days of solar irradiation, respectively. However, the residual concentration remained higher than that permitted by legislation.

When iron was used alone, together with UV, there was 45% abamectin removal after 60 minutes of irradiation. This probably indicates that photoactive complexes formed between iron and other compounds present in the original pesticide sample, and/or their intermediates, were generated during the degradation process [25, 38]. Similar behaviour was observed by Park et al. [39] using the dye Acid Orange 7, by Silva et al. [25] during photo-Fenton degradation of the herbicide tebuthiuron using solar irradiation, and by Sun and Pignatello [40], who attributed the second stage of 2,4-D degradation to iron complex photolysis in the presence of pesticide degradation intermediates. The relatively high degradation efficiency obtained here is interesting since there was no use of H₂O₂, which could reduce the costs of treatment.

For more than 30 years, the use of H₂O₂, a strong oxidant, has been commonplace in treatments involving oxidation of organic and inorganic pollutants [41, 42]. In the present paper, use of H₂O₂ alone (in the absence of irradiation) resulted in 30% removal of abamectin after 60 minutes (Figure 1).

3.2. Degradation Studies

Considering that in the control experiments abamectin removal was in the region of only 30% to 45%, the efficiency of degradation of the compound was also investigated using three different AOPs. Figure 2 shows the results of abamectin degradation using Fenton and photo-Fenton reactions, and the H₂O₂/UV system.

In the experiments using the Fenton reaction, there was 40% abamectin removal after 1 hour of irradiation. Similar degradation efficiency was observed after the same time interval using H₂O₂/UV. Due to the radiation source used, which had a wavelength limit of λ_max = 365 nm, the UV radiation was not able to cause H₂O₂ decomposition, which requires a wavelength near 254 nm [43]. In the present study, the UV radiation probably only acted to remove abamectin by direct photolysis.

Use of the photo-Fenton system improved abamectin degradation, with up to 55% removal after 30 minutes of reaction, and 80% removal after 60 minutes of irradiation. Similar results were obtained by Pignatello [16], who showed that the photo-Fenton process was more efficient than the Fenton process for degradation of 2,4-dichlorophenoxyacetic acid, since photo-reduction of Fe³⁺ ions to Fe²⁺ increased the catalytic effect. The Fe²⁺ ions can react again with H₂O₂, and continue the Fenton reaction. The results obtained in the present paper indicate that the photo-Fenton process is effective for the treatment of water and effluents contaminated with abamectin, with a high removal rate within a short irradiation period of up to 60 minutes.

The hydrogen peroxide concentration is an important parameter influencing Fenton and photo-Fenton processes. At high concentrations it can be detrimental to the degradation of organic compounds in water, since excess H₂O₂ can act as radical scavenger [44]. On the other hand, a lack of H₂O₂ interrupts the Fenton reaction, because its absence can halt hydroxyl radical production and, consequently, destruction of organic compounds. Therefore, monitoring the H₂O₂ concentration can help in adjustment of its initial concentration, and identify any need for further addition during the Fenton process.

Monitoring H₂O₂ levels showed that after 60 minutes there was a residual concentration of at least 10% of the initial concentration, and that there was therefore no need to add more H₂O₂ during the period of irradiation.

Figure 3 shows the outcome of the multiple comparison tests (Tukey’s test at 5% level of significance) applied to the results of the degradation experiments. The photo-Fenton reaction (a) presented higher abamectin degradation efficiency than the other treatments. The Fe/UV treatment (b) showed better degradation efficiency compared to the H₂O₂ and H₂O₂/UV treatments (c). The results using UV alone and the Fenton process were statistically similar to the results obtained for Fe/UV, H₂O₂ alone, and H₂O₂/UV. These results indicated that each individual process could degrade abamectin to some extent; however, the best results were obtained using the photo-Fenton process.

3.3. Photo-Fenton Degradation of Abamectin in Natural Aquatic Samples

Abamectin removal by the photo-Fenton process reached 80% using solutions prepared in distilled water. In order to investigate removal of the pesticide under more natural conditions, the influences of the different physical and chemical parameters were investigated using water samples collected from the José Pereira stream, which were spiked with abamectin. Samples were collected on rainy and dry days. The water collected on a dry day showed values of 120 mg L⁻¹ of total solids and 2 mg L⁻¹ of BOD, while the sample collected during precipitation showed values of 307 mg L⁻¹ of total solids and 4 mg L⁻¹ of BOD. A comparison of abamectin degradation using either distilled water or the natural water samples is shown in Figure 4. It has been reported that organic compound degradation decreases in the presence of natural organic matter and solids, due to reduced penetration of UV radiation. The organic material can compete with the target compound for hydroxyl radicals and/or form complexes with iron, which reduces the efficiency of Fenton degradation [45]. However, even given the possible interferences, abamectin degradation under these conditions reached 70% after 60 minutes of reaction. No difference was observed between degradation of the pesticide in natural water samples collected on rainy or dry days.

3.4. TOC Analysis

Although the results showed that abamectin could be degraded, there was no significant difference in the TOC values after 60 minutes of irradiation. This suggests that abamectin was not mineralised, but that intermediates were generated during the reaction. In a similar study, Fallmann et al. [46] used the photo-Fenton process to treat an aqueous solution containing 100 ppm (TOC) of Vertimec, and observed 20% mineralization after 50 minutes of irradiation, achieving 90% after 150 minutes. However, the authors used a smaller quantity of initial TOC compared to the amount used in the present work (400 ppm). In another study, Bauer et al. [43] used the photo-Fenton reaction to treat a liquid effluent containing a mixture of 10 different pesticides, including Vertimec. The authors used an initial TOC concentration of 10 ppm of each pesticide in distilled water, which was treated in a solar UV reactor (300–400 nm). For the photo-Fenton process they used a concentration of 10⁻³ mmol L⁻¹ FeSO₄·7H₂O and 33 wt % of H₂O_2, which was added in five portions. TOC removal was in excess of 80% after 3 hours of irradiation using the solar photo-Fenton process. The results of these two earlier studies suggest that in the present work, where the Vertimec solution contained an initial 400 ppm of TOC, the irradiation time and the amount of H₂O₂ were probably not sufficient to achieve pesticide mineralization.

Additional experiments were therefore performed in order to try to improve removal of TOC. In an attempt to reproduce the results obtained by Fallmann et al. [46], the initial concentration of TOC was decreased from 400 ppm to 100 ppm of Vertimec, the H₂O₂ concentration was raised to 20 mmol L⁻¹, with an iron concentration of 0.5 mmol L⁻¹. The exposure time was increased to 180 minutes, in line with that employed by Fallmann et al. [46]. The results of these studies, with a ratio Fe/H₂O₂ of 0.0833, showed that 60% of TOC was removed after 180 minutes. This result is very similar to those reported by Bauer et al. [43] and Fallmann et al. [46].

The possibility of reducing treatment costs was studied by decreasing the Fe/H₂O₂ ratio used for mineralization of 400 ppm (TOC) of Vertimec. Using iron and H₂O₂ concentrations of 1.0 mmol L⁻¹ and 80 mmol L⁻¹, respectively (Fe/H₂O₂ ratio of 0.0125), there was 60% TOC removal after 180 minutes of irradiation. A further experiment was performed employing 0.5 mmol L⁻¹ of iron and 80 mmol L⁻¹ of H₂O₂ (Fe/H₂O₂ ratio of 0.00625); however, there was no observable removal of TOC. These results showed that there was a limiting amount of reagents required to achieve TOC removal. Abamectin could be degraded using Fe/H₂O₂ ratios smaller than 0.0125; however, there was no change in the TOC value, indicating that both the original organic compound and TOC should be monitored in order to ensure detoxification of the solution.

Studies of the toxicity and biodegradability of the possible reaction intermediates will be essential in order to establish the optimum concentrations of the photo-Fenton reagents. Future investigations should provide information that addresses the need to effectively mineralize the pesticide, or at least degrade it to a nontoxic intermediate. Additional work is also needed to investigate the possibility of combining a biological process with the photo-Fenton treatment described in the present work.

4. Conclusions

Determination of abamectin by gas chromatography was successfully used to assess the efficiency of degradation of the pesticide by the photo-Fenton process.

The photo-Fenton process was shown to be an effective treatment for water and effluents contaminated with abamectin, achieving a high removal rate of 70% of the chemical after 60 minutes of UV irradiation. Increasing the concentrations of Fe²⁺ and H₂O₂ enabled attainment of at least 60% pesticide mineralization after 180 minutes of irradiation.

Acknowledgments

The authors would like to thank CNPq, CAPES/REUNI, and FAPEMIG for financial support; Dr. José Roberto Guimarães (UNICAMP); Dr. Raquel F. Pupo Nogueira (UNESP) for assistance with the analytical procedures.

References

Z. Huang, Y. Li, B. Chen, and S. Yao, “Simultaneous determination of 102 pesticide residues in Chinese teas by gas chromatography-mass spectrometry,” Journal of Chromatography B, vol. 853, no. 1-2, pp. 154–162, 2007.
View at: Publisher Site | Google Scholar
I. K. Konstantinou, D. G. Hela, and T. A. Albanis, “The status of pesticide pollution in surface waters (rivers and lakes) of Greece. Part I. Review on occurrence and levels,” Environmental Pollution, vol. 141, no. 3, pp. 555–570, 2006.
View at: Publisher Site | Google Scholar
A. J. Dos Santos Neto and M. E. P. B. De Siqueira, “Analysis of organophosphorus pesticides in water using SPE C18 disks and gas chromatography: evaluation of Furnas dam contamination,” Química Nova, vol. 28, no. 5, pp. 747–750, 2005.
View at: Google Scholar
M. J. Cerejeira, P. Viana, S. Batista et al., “Pesticides in Portuguese surface and ground waters,” Water Research, vol. 37, no. 5, pp. 1055–1063, 2003.
View at: Publisher Site | Google Scholar
E. Maloschik, A. Ernst, G. Hegedus, B. Darvas, and A. Székács, “Monitoring water-polluting pesticides in Hungary,” Microchemical Journal, vol. 85, no. 1, pp. 88–97, 2007.
View at: Publisher Site | Google Scholar
F. P. Carvalho, “Agriculture, pesticides, food security and food safety,” Environmental Science and Policy, vol. 9, no. 7-8, pp. 685–692, 2006.
View at: Publisher Site | Google Scholar
N. D. Uri, “A note on the development and use of pesticides,” Science of the Total Environment, vol. 204, no. 1, pp. 57–74, 1997.
View at: Publisher Site | Google Scholar
Joint FAO/WHO Food Standards Program, Codex Committee on Pesticide Residues, CX/PR 97/9 pp. 159, 1997.
M. B. Kralj, P. Trebše, and M. Franko, “Applications of bioanalytical techniques in evaluating advanced oxidation processes in pesticide degradation,” Trends in Analytical Chemistry, vol. 26, no. 11, pp. 1020–1031, 2007.
View at: Publisher Site | Google Scholar
R. Andreozzi, V. Caprio, A. Insola, and R. Marotta, “Advanced oxidation processes (AOP) for water purification and recovery,” Catalysis Today, vol. 53, no. 1, pp. 51–59, 1999.
View at: Google Scholar
V. Claret Dos Santos and M. M. Kondo, “TiO₂ immobilizan onto concrete: chloroform and phenol photodegradation,” Química Nova, vol. 29, no. 2, pp. 251–255, 2006.
View at: Google Scholar
M. Klavarioti, D. Mantzavinos, and D. Kassinos, “Removal of residual pharmaceuticals from aqueous systems by advanced oxidation processes,” Environment International, vol. 35, no. 2, pp. 402–417, 2009.
View at: Publisher Site | Google Scholar
D. Hermosilla, M. Cortijo, and C. P. Huang, “Optimizing the treatment of landfill leachate by conventional Fenton and photo-Fenton processes,” Science of the Total Environment, vol. 407, no. 11, pp. 3473–3481, 2009.
View at: Publisher Site | Google Scholar
J. J. Pignatello, E. Oliveros, and A. MacKay, “Advanced oxidation processes for organic contaminant destruction based on the fenton reaction and related chemistry,” Critical Reviews in Environmental Science and Technology, vol. 36, no. 1, pp. 1–84, 2006.
View at: Publisher Site | Google Scholar
R. F. Pupo Nogueira, A. G. Trovó, M. R. A. Da Silva, R. D. Villa, and M. C. De Oliveira, “Fundaments and environmental applications of Fenton and photo-Fenton processes,” Química Nova, vol. 30, no. 2, pp. 400–408, 2007.
View at: Publisher Site | Google Scholar
J. J. Pignatello, “Dark and photoassisted Fe³⁺-catalyzed degradation of chlorophenoxy herbicides by hydrogen peroxide,” Environmental Science and Technology, vol. 26, no. 5, pp. 944–951, 1992.
View at: Publisher Site | Google Scholar
R. F. Pupo Nogueira and J. R. Guimarães, “Photodegradation of dichloroacetic acid and 2,4-dichlorophenol by ferrioxalate/H₂O₂ system,” Water Research, vol. 34, no. 3, pp. 895–901, 2000.
View at: Publisher Site | Google Scholar
J. A. Herrera-Melián, E. Tello Rendón, J. M. Doña Rodríguez et al., “Incidence of pretreatment by potassium permanganate on hazardous laboratory wastes photodegradability,” Water Research, vol. 34, no. 16, pp. 3967–3976, 2000.
View at: Publisher Site | Google Scholar
E. Balanosky, F. Herrera, A. Lopez, and J. Kiwi, “Oxidative degradation of textile waste water. Modeling reactor performance,” Water Research, vol. 34, no. 2, pp. 582–596, 2000.
View at: Publisher Site | Google Scholar
T. Maezono, M. Tokumura, M. Sekine, and Y. Kawase, “Hydroxyl radical concentration profile in photo-Fenton oxidation process: generation and consumption of hydroxyl radicals during the discoloration of azo-dye Orange II,” Chemosphere, vol. 82, pp. 1422–1430, 2010.
View at: Publisher Site | Google Scholar
M. Pérez-Moya, M. Graells, G. Castells et al., “Characterization of the degradation performance of the sulfamethazine antibiotic by photo-Fenton process,” Water Research, vol. 44, no. 8, pp. 2533–2540, 2010.
View at: Publisher Site | Google Scholar
O. Rozas, D. Contreras, M. A. Mondaca, M. Pérez-Moya, and H. D. Mansilla, “Experimental design of Fenton and photo-Fenton reactions for the treatment of ampicillin solutions,” Journal of Hazardous Materials, vol. 177, no. 1–3, pp. 1025–1030, 2010.
View at: Publisher Site | Google Scholar
V. J. P. Vilar, E. M. R. Rocha, F. S. Mota, A. Fonseca, I. Saraiva, and R. A. R. Boaventura, “Treatment of a sanitary landfill leachate using combined solar photo-Fenton and biological immobilized biomass reactor at a pilot scale,” Water Research, vol. 45, no. 8, pp. 2647–2658, 2011.
View at: Publisher Site | Google Scholar
N. Klamerth, L. Rizzo, S. Malato, M. I. Maldonado, A. Agüera, and A. R. Fernández-Alba, “Degradation of fifteen emerging contaminants at μg $L^{- 1}$ initial concentrations by mild solar photo-Fenton in MWTP effluents,” Water Research, vol. 44, no. 2, pp. 545–554, 2010.
View at: Publisher Site | Google Scholar
M. R. A. Silva, A. G. Trovó, and R. F. P. Nogueira, “Degradation of the herbicide tebuthiuron using solar photo-Fenton process and ferric citrate complex at circumneutral pH,” Journal of Photochemistry and Photobiology A, vol. 191, no. 2-3, pp. 187–192, 2007.
View at: Publisher Site | Google Scholar
M. R. A. Silva, W. Vilegas, M. V. B. Zanoni, and R. F. Pupo Nogueira, “Photo-Fenton degradation of the herbicide tebuthiuron under solar irradiation: iron complexation and initial intermediates,” Water Research, vol. 44, no. 12, pp. 3745–3753, 2010.
View at: Publisher Site | Google Scholar
M. M. Kondo, K. U. C. G. Leite, M. R. A. Silva, and A. D. P. Reis, “Fenton and photo-fenton processes coupled to uasb to treat coffee pulping wastewater,” Separation Science and Technology, vol. 45, no. 11, pp. 1506–1511, 2010.
View at: Publisher Site | Google Scholar
M. Ribani, C. B. Grespan Bottoli, C. H. Collins, I. C. S. Fontes Jardim, and L. F. Costa Melo, “Validation for chromatographic and electrophoretic methods,” Química Nova, vol. 27, no. 5, pp. 771–780, 2004.
View at: Google Scholar
J. Hernández-Borges, L. M. Ravelo-Pérez, E. M. Hernández-Suárez, A. Carnero, and M. A. Rodríguez-Delgado, “Analysis of abamectin residues in avocados by high-performance liquid chromatography with fluorescence detection,” Journal of Chromatography A, vol. 1165, no. 1-2, pp. 52–57, 2007.
View at: Publisher Site | Google Scholar
R Development Core Team, R: A Language and Environment for Statistical Computing, R Foundation for Statistical Computing, Vienna, Austria, 2009.
R. F. P. Nogueira, M. C. Oliveira, and W. C. Paterlini, “Simple and fast spectrophotometric determination of H₂O₂ in photo-Fenton reactions using metavanadate,” Talanta, vol. 66, no. 1, pp. 86–91, 2005.
View at: Publisher Site | Google Scholar
H. Diserens and M. Henzelin, “Determination of abamectin residues in fruits and vegetables by high-performance liquid chromatography,” Journal of Chromatography A, vol. 833, no. 1, pp. 13–18, 1999.
View at: Publisher Site | Google Scholar
A. I. Valenzuela, D. S. Popa, M. J. Redondo, and J. Mañes, “Comparison of various liquid chromatographic methods for the analysis of avermectin residues in citrus fruits,” Journal of Chromatography A, vol. 918, no. 1, pp. 59–65, 2001.
View at: Publisher Site | Google Scholar
M. Danaher, L. C. Howells, S. R. H. Crooks, V. Cerkvenik-Flajs, and M. O'Keeffe, “Review of methodology for the determination of macrocyclic lactone residues in biological matrices,” Journal of Chromatography B, vol. 844, no. 2, pp. 175–203, 2006.
View at: Publisher Site | Google Scholar
M. D. Hernando, J. M. Suárez-Barcena, M. J. M. Bueno, J. F. Garcia-Reyes, and A. R. Fernández-Alba, “Fast separation liquid chromatography-tandem mass spectrometry for the confirmation and quantitative analysis of avermectin residues in food,” Journal of Chromatography A, vol. 1155, no. 1, pp. 62–73, 2007.
View at: Publisher Site | Google Scholar
M. Mushtaq, A. C. Chukwudebe, C. Wrzesinski, L. R. S. Allen, D. Luffer-Atlas, and B. H. Arison, “Photodegradation of emamectin benzoate in aqueous solution,” Journal of Agricultural and Food Chemistry, vol. 46, no. 3, pp. 1181–1191, 1998.
View at: Google Scholar
A. Kamel, S. Al-Dosary, S. Ibrahim, and M. Asif Ahmed, “Degradation of the acaricides abamectin, flufenoxuron and amitraz on Saudi Arabian dates,” Food Chemistry, vol. 100, no. 4, pp. 1590–1593, 2007.
View at: Publisher Site | Google Scholar
R. F. P. Nogueira, M. R. A. Silva, and A. G. Trovó, “Influence of the iron source on the solar photo-Fenton degradation of different classes of organic compounds,” Solar Energy, vol. 79, no. 4, pp. 384–392, 2005.
View at: Publisher Site | Google Scholar
J. S. Park, K. H. Kim, G. J. Kwon et al., “Development of small and efficient ozone generation using corona discharge,” Korus-Physics, vol. 1, pp. 282–284, 2001.
View at: Google Scholar
Y. Sun and J. J. Pignatello, “Photochemical reactions involved in the total mineralization of 2,4-D by Fe³⁺/H₂O₂/UV,” Environmental Science and Technology, vol. 27, no. 2, pp. 304–310, 1993.
View at: Google Scholar
E. Neyens and J. Baeyens, “A review of classic Fenton's peroxidation as an advanced oxidation technique,” Journal of Hazardous Materials, vol. 98, no. 1–3, pp. 33–50, 2003.
View at: Publisher Site | Google Scholar
R. Venkatadri and R. W. Peters, “Chemical oxidation technologies: ultraviolet light/hydrogen peroxide, Fenton's reagent, and titanium dioxide-assisted photocatalysis,” Hazardous Waste and Hazardous Materials, vol. 10, no. 2, pp. 107–149, 1993.
View at: Google Scholar
R. Bauer, G. Waldner, H. Fallmann et al., “The photo-fenton reaction and the TiO₂/UV process for waste water treatment—novel developments,” Catalysis Today, vol. 53, no. 1, pp. 131–144, 1999.
View at: Google Scholar
W. C. Paterlini and R. F. P. Nogueira, “Multivariate analysis of photo-Fenton degradation of the herbicides tebuthiuron, diuron and 2,4-D,” Chemosphere, vol. 58, no. 8, pp. 1107–1116, 2005.
View at: Publisher Site | Google Scholar
R. G. Zepp, B. C. Faust, and J. Holgné, “Hydroxyl radical formation in aqueous reactions (pH 3-8) of iron(II) with hydrogen peroxide: the photo-fenton reaction,” Environmental Science and Technology, vol. 26, no. 2, pp. 313–319, 1992.
View at: Google Scholar
H. Fallmann, T. Krutzler, R. Bauer, S. Malato, and J. Blanco, “Applicability of the Photo-Fenton method for treating water containing pesticides,” Catalysis Today, vol. 54, no. 2-3, pp. 309–319, 1999.
View at: Google Scholar

Copyright

Copyright © 2012 Thiago Augusto de Freitas Matos et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

4002

Downloads

2060

Citations