Parametric Analysis of a High Temperature PEM Fuel Cell Based Microcogeneration System

Nomnqa, Myalelo; Ikhu-Omoregbe, Daniel; Rabiu, Ademola

doi:https://doi.org/10.1155/2016/4596251

International Journal of Chemical Engineering

On this page

Abstract Introduction Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2016 | Article ID 4596251 | https://doi.org/10.1155/2016/4596251

Parametric Analysis of a High Temperature PEM Fuel Cell Based Microcogeneration System

Myalelo Nomnqa,¹Daniel Ikhu-Omoregbe,¹and Ademola Rabiu¹

Academic Editor: Deepak Kunzru

Received23 Mar 2016

Accepted22 May 2016

Published23 Jun 2016

Abstract

This study focuses on performance analysis of a 1 microcogeneration system based on a high temperature proton exchange membrane (HT-PEM) fuel cell by means of parametric investigation. A mathematical model for a system consisting of a fuel processor (steam reforming reactor and water-gas shift reactor), a HT-PEM fuel cell stack, and the balance-of-plant components was developed. Firstly, the fuel processor performance at different fuel ratios and equivalence ratio was examined. It is shown that high fuel ratios of 0.9–0.95 and equivalence ratios of less than 0.56 are suitable for acceptable carbon monoxide content in the synthetic gas produced. Secondly, a parametric study of the system performance at different fuel and equivalence ratios using key system operating parameters was conducted. Steam-to-carbon ratio, stack operating temperature, and anode stoichiometry were varied to observe the changes in the microcogeneration system. The analysis shows that the system can reach electrical and cogeneration efficiencies of 30% and 84%, respectively.

1. Introduction

Because of the inefficiency and pollution associated with centralized power generation, there has been growing interest in shifting to distributed (decentralized) power generation systems. Cogeneration (or Combined Heat and Power (CHP)) is seen to have the potential to primary energy savings and greenhouse gas emissions reduction when compared with large power stations [1, 2]. Cogeneration is the combined production of electrical and thermal energy from a single primary energy source. In residential applications, cogeneration provides electricity and heat (for hot water and space heating) for the household. Fuel cells, specifically the polymer electrolyte membrane (PEM) fuel cell and the solid oxide fuel cell (SOFC), are considered as an alternative to combustion based technologies utilized to meet heating requirements. This is because they exhibit high efficiencies, low emissions and noise levels, modularity, and a low heat-to-power ratio [3]. The low temperature PEM (LT-PEM) fuel cells are the most developed and widely studied type of PEM fuel cell, operating at relatively low temperatures (<80°C) and have Nafion based membrane. Microcogeneration systems based on LT-PEM fuel cell have been widely demonstrated and have enjoyed some commercialization success [4]; there are however disadvantages associated with this stack technology. For instance, the proton conduction mechanism of Nafion membrane requires water management systems to prevent MEA flooding/drying. The low operating temperature makes the LT-PEM fuel cell be susceptible to carbon monoxide poisoning and thus requires 99.99% hydrogen-rich gas.

The development of a high temperature PEM (HT-PEM) fuel cell which operates at higher temperature (120°C–200°C) has overcome these issues. Because the proton conduction mechanism in the polybenzimidazole- (PBI-) based HT-PEM fuel cell is dependent on the phosphoric acid content and not on the membrane water content [5, 6], the need for complex water management systems is eliminated, thus simplifying the system design. The high temperature operation improves the PEM fuel cell performance and has operational advantages, such as tolerance to carbon monoxide (CO) levels [7–10]. The HT-PEM fuel cell has a tolerance of CO of up to 3% in hydrogen at 0.8 A cm⁻² and 200°C as reported by Li et al. [10]. The improved tolerance to CO allows use of a synthetic gas from various fuel sources without the need for complex CO clean-up systems [11–15]. Gardemann et al. [11] demonstrated a compact ethanol fuel processor for small scale system (200 W–500 W) [11]. Maximini et al. [12] reported on the development of a steam reforming based fuel processor for diesel operation. Samsun et al. [13] explored a start-up strategy based on utilization of electrical heaters at different locations in the fuel processor to heat process air of diesel and kerosene fuel processor via modeling and experiments. They reported an improved start-up time of the fuel processor from 22 min to 9.5 min when the strategy is applied. Authayanun et al. [14] analyzed the integration of a glycerol fuel processor and a HT-PEM. They considered the effects of steam-to-carbon ratio (S/C) and reforming temperature on the reformate gas composition. Similarly, Perna et al. [15] conducted a sensitivity analysis of a LPG reformer coupled with a membrane shift reactor for a 5 kW system with results showing the reforming pressure as a critical parameter for improved fuel processor performance.

Recently there has been increased interest in studying cogeneration systems based on HT-PEM fuel cell. Authayanun et al. [16] conducted a comparison study of a 3 cogeneration system, based on HT-PEM and LT-PEM fed with pure hydrogen, and using a reformate gas from a glycerol reformer. The LT-PEM system demonstrated better performance for pure hydrogen operation, while the HT-PEM system exhibited better performance for reformate operation at full load (4000 A m⁻²). Similar results were shown by Jannelli et al. [17] when they compared three cogeneration systems operating at 60°C, 160°C, and 180°C, based on fuel stacks with different membranes. Their results indicated that the HT-PEM systems had electrical and cogeneration efficiencies of 40% and 78%, respectively. Because fuel cell systems do not always operate at design points, as when there is less demand for electrical energy, some authors have studied off-design performance. Arsalis et al. [18] and Zuliani and Taccani [19] investigated partial load performance of a 1 HT-PEM cogeneration system, with similar results showing that the efficiency increased at partial loads. Both investigations showed that the system balance-of-plant (BoP) components do not have a significant effect on the system performance when the load is reduced. The work done by Najafi et al. [20] showed that the electrical efficiency can be increased from 21.18% to 29.21% and the primary saving index from 6.07% to 17.50% when a LT-PEMFC stack is replaced with an HT-PEM stack in an existing 30 cogeneration system.

Other researchers have optimized the system performance [21–23]. Rabiu et al. [21] reported on application of heat integration technique to optimize the heat exchanger network of a 2 kW system. Arsalis et al. [22] investigated optimization using two techniques: pinch analysis for maximization of electrical efficiency and mixed integer nonlinear programming for minimization of heat exchanger network (HEN) annual costs. The authors showed that the combination of these two techniques could lead to a lower HEN annual cost of US$8,147/year without affecting electrical efficiency. Arsalis et al. [23] have optimized a heat-pump assisted cogeneration system by considering thermophysical parameters at different loads. Najafi et al. [24] explore the use of operating strategies to mitigate the decay of electrical and thermal power output in the first 15,000 hours of a 30 kW plant. According to their recovery strategy, 422.6 MWh of electricity is generated as compared to the 381.3 MWh generated at normal operation during the system lifetime.

The objective of this study was to establish the effects of fuel processor operating parameters on performance parameters such as component yields from fuel processor, system power outputs, and their related efficiencies. Future studies will incorporate these findings in optimization studies exploring the effect of the cogeneration system operating parameters.

2. Modeling of the Cogeneration System

A schematic representation of the natural gas-fuelled system consisting of two subsystems, the HT-PEM fuel cell and the fuel processing subsystem, is shown in Figure 1. It is assumed that natural gas contains only methane (CH₄).

2.1. Methane Steam Reformer (MSR)

The model presented can apply any kinetic model appropriate for the type of catalyst used. In this work, the intrinsic kinetic expressions reported by Xu and Froment [26] for nickel-alumina catalysts that have been widely used in literature are adopted. The reaction kinetics are based on the Langmuir-Hinshelwood reaction mechanism, consisting of the steam reforming reaction and the water-gas shift (WGS) reaction. Two global reaction schemes are considered and are expressed as follows:Their respective rate equations are as follows: For methane steam reforming, For water-gas-shift,The rate constants and adsorption constants are determined by the Arrhenius and Van’t Hoff relations:

2.2. Water-Gas Shift (WGS)

The reformate gases leaving the steam reformer are a mixture of mainly hydrogen (H₂), carbon dioxide (CO₂), water vapor (H₂O), carbon monoxide (CO), and small traces of methane (CH₄). The platinum catalyst used in the fuel cell stack is prone to CO poisoning in the temperature range at which it operates. Thus, to reduce the CO content in the reformate gas, the gas is fed to a shift reactor where the CO reacts with H₂O to produce more H₂. In the WGS reactor the CO content should be reduced to an acceptable level (for the fuel cell stack) of less than 2%. The kinetic model of the WGS reactor is described in detail in Kim et al. [27], and global reaction considered is expressed as follows:

2.3. Catalytic Combustor

The steam reforming reaction is highly endothermic and needs to be supplied with heat for it to proceed. The anode off-gas is fed to the catalytic combustor, where the unreacted H₂, CH₄, and CO are burned with air to supply the required heat to the steam reformer. Additional CH₄ is also supplied to the combustor because the anode off-gas is not sufficient to maintain the required temperature in the steam reformer. The reactions occurring in the combustor areThe reaction kinetics of hydrogen (Schefer [28]) methane (Song et al. [29]) and carbon monoxide (Cant et al. [30]) combustion on a platinum catalyst are used.

For methane combustion,

For hydrogen combustion,

For carbon monoxide combustion,

2.4. HT-PEM Fuel Cell Stack

The fuel cell stack model was developed using a modular approach in which each component (flow channel, gas diffusion layer, and catalyst layer) was individually modeled and the connectivity equations at the boundaries are used to connect the adjacent layers. Figure 2 shows the schematic of the modeling domain considered in the fuel cell model.

Basic Assumptions(1)All chemical components of working fluid are considered as ideal incompressible gases, and fully developed laminar flow is considered.(2)Single phase operation.(3)Isothermal operation.(4)No reactant crossover in the electrolyte.(5)The concentration polarization loss is neglected.(6)Steady state operation is assumed.(7)Heat loss to surroundings is negligible.

2.4.1. Gas Channel Subdomain

In the gas channels the consumption of hydrogen and oxygen (O₂) due to electrochemical reactions occurs and water vapor is produced. The conservation of the mass in the presence of electrochemical reactions leads to a set of ordinary differential equations for the rate of change of molar concentrations with respect to axial position within the flow channel. The conservation of mass is solved along the axial coordinate () for the anode and cathode as follows:where is the total gas concentration in the channel, is the gas velocity, and represents the species molar fractions. The source term represents the species reaction. The source terms of species taking part in the reactions (H₂, O₂, and H₂O) are calculated aswhere represents the current density and the molecular mass of each species. The mass conservation equations are complemented with the associated boundary. The boundary conditions dictate that the molar concentrations of each species at the channel inlet are equal to those of the respective feed stream. A first-order finite difference method (BFDM) with 20 discrete points was used to solve the governing equations in the flow channel.

2.4.2. MEA Subdomain

In MEA five components are included in the model: the anode and cathode gas diffusion layers, the anode and cathode electrodes, and the membrane. Only mass transport due to diffusion is considered in the MEA direction (). Mass transport in the gas diffusion layer is considered to be 1D along the diffusion flux direction. The Stefan-Maxwell equation is to describe the mass transfer in the GDL:where is the effective binary diffusion coefficient between species and and represents the molar flux of species . The correlation proposed by Jiao et al. [31] was used to determine the binary diffusion coefficients (18), which were subsequently corrected using Bruggeman’s correlation to account for the tortuosity and porosity of porous media (19). A second-order centre finite difference method with 5 discrete points is employed to solve the governing equation in the GDL:

2.4.3. Electrochemical Model

The electrochemical reactions in the HT-PEMFC occur in the thin catalyst zones which are close to the electrode and membrane. In this work it is assumed that electrochemical reactions only occur at the GDL/CL interface, and as such the catalyst layers are modeled as interfaces. This simplification has been widely used in cell-level and system-level analysis. The concentrations of the reacting species (H₂ and O₂) at the catalyst interface are determined using Fick’s law of diffusion [32]: represents the species concentration on the catalyst surface, is the equilibrium concentration in the acid thin film at the studied temperature, and is the film thickness. The concentrations of the species dissolving at the thin film boundary () are calculated from their solubility [32]:where is the species mole fraction at the electrode/electrolyte interface. The correlations employed by Cheddie and Munroe [33] are used to calculate the solubility and diffusivity of O₂ in phosphoric acid, whereas the diffusivity and solubility of H₂ are assumed to be two times and four times those of O₂, respectively. The activation over voltage due to electrochemical reactions is calculated using the Butler-Volmer equation for the Oxygen Reduction Reaction and Hydrogen Oxidation Reaction:where the exchange current density is approximated byBecause of a reformate gas operation, the effect of CO poisoning on the anode catalyst layer is accounted for using a modified the current density () [34]:where the temperature dependence of the surface coverage of the reaction site by CO () is obtained by correlation employed by Dhar et al. [35]:The ohmic loss follows Ohm’s law and is caused by a resistance of ions in the electrolyte through membrane. The proton conductivity () as a function of temperature and acid doping level () follows the Arrhenius law as obtained from Cheddie and Munroe [33]:The total cell voltage () is given bywhere the thermodynamic equilibrium potential () is determined using the Nernst equation:

2.5. Heat Exchangers

The thermal analysis of the heat exchangers is based on the number of transfer units (NTU) method based on the concept of heat exchanger effectiveness (). The effectiveness of a heat exchanger is the ratio of the actual heat transfer rate to the thermodynamically limited maximum possible heat transfer rate if an infinite heat transfer surface area was available. For a cross-flow compact heat exchanger with both fluids unmixed, the -NTU function is

2.6. System Performance Parameters

The objective functions that are used in the analysis of the system performance are the fuel processor efficiency (), fuel consumption (), electrical efficiency (), and cogeneration efficiency (). The fuel processor efficiency is defined as the ratio of hydrogen produced in the fuel processor and the amount of chemicals available in the input gas (methane) entering the system:where is the mass flow rate of hydrogen at the anode inlet and is the total mass flow rate of methane which is consumed. Fuel conversion/consumption rate is one of the most widely used parameters evaluating fuel processor performance defined aswhere is the methane flow rate at the MSR outlet and is methane flow rate at the MSR inlet. The electrical efficiency is defined as the ratio of the electrical power output from the fuel cell stack divided by the chemical energy of the hydrogen from the fuel processor:where represents the electrical power produced in the fuel cell stack. The system cogeneration efficiency is defined as the sum of the thermal and electrical power divided by the amount of methane which is consumed:where is the thermal energy recoverable from the cogeneration heat exchanger. The system model was implemented in a commercial application, gPROMS Model Builder version 3.6.0 from PSE Ltd. [36]. The computation station consists of a 64-bit Windows platform, 8 GB RAM, and an Intel(R) Core™ i5 3.20 GHz processor. The gPROMS DASolver is used to solve numerical functions during simulation.

3. Model Validation

The fuel cell characteristics obtained from the model and experimental results from Bujlo et al. [37] at different operating conditions are compared in Figure 3. The model is calibrated using the gPROMS parameter estimation module where the fuel cell electrochemical parameters (Table 1) are estimated to predict the performance of the model to that of the experiment. As can be noted in Figure 3, there is an acceptable agreement between the model and the experimental results, which verifies the validity of the model. To verify the validity of the fuel processor model, the simulation results were compared with results from the literature. Two sets of data were selected for this purpose, experimental data by Di Bona et al. [38] and numerical data by Jung et al. [39].

Figure 4 compares the simulation, experimental, and numerical results of the dry gas composition at the outlet of the WGS reactor. The simulation results from this work agree well with these data sets. Similar to the fuel processor validation, the cogeneration system developed in this paper is validated using numerical and experimental data from literature of HT-PEM [19] and LT-PEM [25] based systems. In Zuliani and Taccani [19] commercial software Aspen Plus™ is employed to simulate the performance of a natural gas-fuelled system using energy balances. It can be noted in Table 2 that the cogeneration system in this paper compares well with the data of the HT-PEM system, showing similar electrical, fuel processor, thermal and cogeneration efficiencies. Briguglio et al. [25] conducted experiments to explore using direct water injection in the cathode of LT-PEM system operating at 73°C as a heat recovery strategy from the stack and it suitability for cogeneration application. The LT-PEM system has higher electrical efficiency of 44% (HHV) and lower thermal efficiency of 36% (HHV) when compared to the system developed by the authors.

4. Simulation Results

A parametric study was conducted to investigate the effect of different operating parameters on the system performance. Accordingly, to study the behavior of the fuel processor, the mixed effect of variation of combustor equivalence ratio and the fuel ratio on the performance of the systems was considered first. Based on this, a case study in which four operating points based on the combination of the two parameters was chosen.

In the four points chosen, the required constraints such as the CO concentration in the fuel cell anode inlet were met. From a design perspective, to maintain realistic dimensions of the cogeneration system, the fuel cell stack design parameters as shown in Table 3 and all heat exchangers geometries were kept constant in each of the cases considered.

4.1. Combustor Operating Parameters

As an initial investigation, the effect of variation of the combustion parameters (fuel ratio and equivalence ratio) on the fuel processor performance was investigated. The combustion of the fuel and air is a chemical reaction that strongly depends on the composition of the fuel and air fed to the combustor. The fuel ratio (FR) was defined as the ratio of the combined flow rate of combustion fuel (auxiliary CH₄ and combustible gases in the anode off-gas) to that of the CH₄ flow rate into the reformer; it was varied by increasing the auxiliary CH₄ flow rate into the combustor. The equivalence ratio () was defined as the actual fuel/oxidant (air) ratio normalized by the stoichiometric fuel/oxidant ratio into the combustor [40]:Figure 5 presents the contour plots of the simulated cases carried out for fuel ratios range (0.75–0.95) and equivalence ratios range (0.45–0.75). The results of combined effect of the fuel ratio and equivalence ratio are summarized by plots of the temperature of the MSR and WGS reactors, fuel processor efficiency, and fuel consumption rate. Figures 5(a) and 5(b) show the temperature at the outlet of the MSR and WGS reactors. It can be seen that increasing the equivalence ratio and fuel ratio results in a rise of reactor outlet temperatures. The simulation shows that the temperatures of the reactor outlets are the highest when the approaches unity for all fuel ratios considered. This is caused by the increase in the heat of combustion due to increased fuel conversion in the combustor which raises the heat transferred to the reforming reactor. Figure 5(c) shows that for equivalence ratio less 0.56 the fuel processor efficiency increases with increased fuel ratios (a similar trend to the reactor temperatures). However, a peak of the efficiency is visible at different fuel ratios for equivalence ratios greater than 0.56. If the fuel ratio is higher than the peak fuel ratio the fuel processor efficiency decreases. This implies that when the reforming temperature rises above 1020 K, the fuel processor efficiency drops.

(a)

(b)

(c)

(d)

The fuel processor efficiency depends on the H₂ production rates from both the fuel MSR and WGS reactors. Increased steam reforming temperature increases the rates of the MSR reaction and decreases the WGS reaction. Because the magnitude of the reaction rate of the WGS reaction is lower on the MSR reactor, H₂ production is expected to be high in the MSR reactor at high temperatures. In the WGS reactor the effects of the high temperature operation on the WGS reaction are visible because of the magnitude of this reaction. The higher temperature results in less CO being converted to H₂, reducing the H₂ production rate from the fuel processor, which explains the peak observed in the fuel processor efficiency. Another important variable to measure the performance of the fuel processor is the fuel consumption/conversion. Figure 5(d) shows the relationship between the fuel consumption and the two fuel processor parameters. Because the fuel consumption and the fuel processor efficiency are related, they are expected to exhibit the same trend. However, the results show that the fuel consumption does not reach a peak like the fuel processor efficiency. Unlike the fuel processor efficiency, the fuel consumption only depends only on the CH₄ reforming in the MSR reactor. As mentioned above increasing the reforming temperature results in an increase in CH₄ conversion towards H₂ and CO. This explains the similar trend of the fuel consumption and the MSR reactor temperature when the fuel and equivalence ratios are varied.

It is important to consider how the fuel processor parameters affect the quality of the reformate gas produced. Lee et al. [40] showed that to maximize the synthesis gas production from a steam reformer, for use in a SOFC and MCFC, the fuel ratio should not exceed 80%. In this work the effect of varying the fuel ratio and equivalence ratio on the reformate gas composition is considered. Figure 6 presents the concentration (in dry basis) of the reformate species entering the fuel cell stack. It can be noted in Figure 6(a) that the CH₄ concentration decreases with increased equivalence ratio for range of fuel ratios. This is consistent with what is shown in Figure 5(d), illustrating the increased temperature effects on CH₄ consumption. Figure 6(c) depicts an increasing trend in the H₂ concentration when the fuel ratio is increased at every equivalence ratio. The highest value for H₂ concentration of 79.3% is obtained at high fuel and equivalence ratios. Figure 6(d) shows the carbon monoxide concentration in the fuel processor. For fuel ratios between 0.75 and 0.85, a decrease in the CO concentration is observed when the equivalence ratio is increased. However, when the equivalence ratio reaches 0.56, the CO concentration starts to increase. For fuel ratios above 0.85, the CO concentration has been observed to increase monotonically with the equivalence ratio.

(a)

(b)

(c)

(d)

4.2. System Operating Parameters

To investigate the behavior of the system at various operating conditions, four operating points, based on different combinations of fuel ratio and equivalence ratio, were chosen and are presented in Table 4. The operating points were chosen so that they cover a wide range of CO inlet into fuel cell stack. The effects of the varying the S/C ratio (2.5–4) on the performance of the fuel processor are presented in Figures 7 and 8. It can be seen in Figure 7 that increasing the S/C ratio from 2.5 to 4 results in 14.67%, 13.92%, 12.49%, and 11.3% increase in the fuel processor efficiency for cases A, B, C, and D, respectively. The main reason for this behavior is that increasing the S/C ratio has a positive effect on the kinetics of the reactors in the fuel processor. It increases the rate of the steam reforming and water-gas-shift reactions in the MSR ((1) and (2)) and the water-gas-shift reaction [20] in the shift reactor (6). The net effect of this is increased H₂ concentration (in dry basis) for the four cases in the reformate gas entering the fuel cell stack. The calculated carbon monoxide concentration (in dry basis) in the reformate gas entering the fuel cell stack for varying S/C ratio is presented in Figure 8. As it would be expected, increasing the S/C ratio from 2.5 to 4 reduces the carbon monoxide concentration by 50.5%, 57.3%, 65.6%, and 68.3% for cases A, B, C, and D, respectively. The decrease in CO concentration and strong influence in fuel processor efficiency is in agreement with work published by Ersöz and Sayar [41] for an Autothermal Reforming based system.

The effect of varying the fuel cell stack operating temperature in the performance of the system is shown in Figures 9 and 10. From Figure 9, it is observed that increasing the stack operating temperature results in an increase in the stack average cell voltage for all cases considered as expected. This is a result of improved reaction kinetics in the cell catalyst layer that decreases the associated cell voltage losses [32]. To explain the observed behavior for each case in Figure 9, we consider two cases (A and D). The operating points for each case in Table 4 lead to different carbon monoxide composition in the stack anode inlet, lowest in case A (0.32%) and highest in case D (0.72%). As a result of this, case A results in the highest cell voltage and case D in the lowest one for all temperatures. It can be also noted that while there is small difference in the cell voltage at lower temperatures, case A and case B show better performance at high temperatures because of the low CO content in the anode inlet. Figure 10 presents the variation of the stack electrical efficiency at different stack operating temperatures. Because the power generated in the stack is proportional to the stack voltage, a trend similar to that of the voltage at different operating temperature is observed [20].

The anode stoichiometric ratio is an important parameter in the system as it determines the concentration of fuel in the combustor [42] and operating temperature. Simulations of system performance were conducted at four anode stoichiometric ratios (1.25–1.55) and the results are presented in Figure 11. As the stoichiometric ratio is increased, the molar fraction of hydrogen in the anode off-gas is increased. This results in increased temperature in the combustor and reformer, thus increasing the fuel processor efficiency and system thermal efficiency. Increased temperature of combustion gases also leads to large amounts of heat available for thermal power generation in cogeneration heat exchanger (HX-1). An increasing trend was observed in the cogeneration efficiency from 79% to 82% as a result of an increment (from 1.25 to 1.55) in the anode stoichiometric ratio for case C. Although increasing the stoichiometric ratio results in better cogeneration efficiency, this is to the detriment of the stack electrical efficiency as it decreases. The higher heat transferred to the reformer leads to increased CO levels in the anode inlet, which subsequently results in decreased cell voltage. The effect of the stoichiometric ratio on the electrical efficiency is also shown in Figure 11 and a decreasing trend can be observed for all the cases considered.

Surface plots were generated in order to investigate the sensitivity of the electrical and cogeneration efficiency to the changes in the three parameters. In doing so, the effect of changing two parameters within one simulation can be determined. For this analysis case C has been considered. Figures 12 and 13 present the sensitivity of the electrical and cogeneration efficiencies of the system. The system optimal point for maximum electrical efficiency can be defined from Figures 12(a), 12(b), and 12(c). It corresponds to high S/C ratio, high temperature, and lower anode stoichiometry. In a similar manner, surface plots depicting the sensitivity of the cogeneration efficiency to the three parameters are presented in Figures 13(a), 13(b), and 13(c). For maximizing cogeneration efficiency high anode stoichiometry, high S/C ratio, and high temperature present the optimal point. The selection of maximizing electrical or cogeneration efficiency depends on the operation strategy selected by the end user [43]. The two commonly used strategies are the electrical load driven and thermal load driven operations. For electricity load driven operation where the system is operated to meet the electrical demand, operating point which maximizes the electrical efficiency would be considered as optimal. Similarly for a user with high thermal load demand, maximizing the cogeneration efficiency would be preferred.

(a)

(b)

(c)

(a)

(b)

(c)

5. Conclusions

In this work, a model for a 1 HT-PEM fuel cell cogeneration system suitable for residential application is presented. In the first part of our investigations, a parametric study of the combustor parameters (fuel ratio and equivalence ratio) was conducted. It is shown that while higher fuel ratio and equivalence ratio lead to high fuel processor efficiencies, they result in high levels of CO content in the reformate gas that are not acceptable to the fuel cell stack. Using four operating points that represent the combination of fuel ratio and equivalence ratio, a parametric study of the cogeneration system was conducted. Variation of the steam-carbon ratio, stack operating temperature, and anode stoichiometric ratio on the system performance was considered. Increasing the SC ratio (2.5–4.0) resulted in increased fuel processor performance, reducing the anodic CO molar fraction to less than 0.4% for all the cases. The stack average cell voltage was shown to increase as a result of lower CO molar fraction in the anode inlet. It was shown that increasing the stack operating temperature (403–443 K) increased the electrical efficiency from 34.84% to 38.34% for case A. It was also shown that while high temperature operation results in increased voltage for all cases, better performance for cases with lower CO content is obtained at high temperatures. Increasing the anode stoichiometric ratio from 1.25 to 1.55 has a positive impact on the cogeneration efficiency while the electrical efficiency dropped, showing that the anode stoichiometry can be useful in regulating the system load demands.

Symbols

	Concentration (mol/m³)
:	Heat capacity ratio
:	Activation energy (kJ/mol)
:	Faraday constant (C/mol)
HEX:	Heat exchanger
:	Exchange current density (A/m)
:	Reaction rate constant (kmol bar^0.5/ h)
:	Adsorption constant (1/bar)
:	Equilibrium constant
LHV:	Lower heating value (kJ/kg)
:	Mass flow rate (kg/s)
:	Number of electrons transferred
:	Number of transfer units
:	Partial pressure (Pa)
:	Reaction rate (kmol/s )
:	Universal gas constant (kJ/kmol K)
:	Temperature (K)
:	Voltage (V)
:	Power (W)
:	Acid doping level (—)
:	Mole fraction (—).

Greek

:	Efficiency
:	Heat exchanger effectiveness
:	Transfer coefficient
:	Fraction of catalyst surface covered by CO.

Subscripts and Superscripts

:	Activation
:	Anode
:	Cathode
cell:	Single cell
cogen:	Cogeneration
el:	Electrical
eq:	Equilibrium
:	Component
:	Reaction
ocv:	Open-circuit voltage
ohm:	Ohmic
ox:	Oxidation
rd:	Reduction
th:	Thermal.

Competing Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The financial assistance of the National Research Foundation (NRF) towards this research is hereby acknowledged. Opinions expressed and conclusions arrived at are those of the authors and are not necessarily to be attributed to the NRF. The authors would like to thank Dr. Yusuf Isa from the Durban University of Technology for his assistance in the development of the models.

References

G. Angrisani, C. Roselli, and M. Sasso, “Distributed microtrigeneration systems,” Progress in Energy and Combustion Science, vol. 38, no. 4, pp. 502–521, 2012.
View at: Publisher Site | Google Scholar
D. Sonar, S. L. Soni, and D. Sharma, “Micro-trigeneration for energy sustainability: technologies, tools and trends,” Applied Thermal Engineering, vol. 71, no. 2, pp. 790–796, 2014.
View at: Publisher Site | Google Scholar
J. Geraldo de Melo Furtado, G. C. Gatti, E. T. Serra, and S. C. Anibal De Almeida, “Performance analysis of a 5 kW PEMFC with a natural gas reformer,” International Journal of Hydrogen Energy, vol. 35, no. 18, pp. 9990–9995, 2010.
View at: Publisher Site | Google Scholar
FuelCellToday, The Fuel Cell Industry Review, 2013.
L. Xiao, H. Zhang, T. Jana et al., “Synthesis and characterization of pyridine-based polybenzimidazoles for high temperature polymer electrolyte membrane fuel cell applications,” Fuel Cells, vol. 5, no. 2, pp. 287–295, 2005.
View at: Publisher Site | Google Scholar
J. Zhang, J. Wu, H. Zhang, and J. Zhang, “High-temperature PEM fuel cells,” in Pem Fuel Cell Testing and Diagnosis, J. Zhang, J. Wu, H. Zhang, and J. Zhang, Eds., chapter 10, pp. 243–282, Elsevier, Amsterdam, The Netherlands, 2013.
View at: Google Scholar
Z. Qi and S. Buelte, “Effect of open circuit voltage on performance and degradation of high temperature PBI-H₃PO₄ fuel cells,” Journal of Power Sources, vol. 161, no. 2, pp. 1126–1132, 2006.
View at: Publisher Site | Google Scholar
L. Qingfeng, H. A. Hjuler, and N. J. Bjerrum, “Phosphoric acid doped polybenzimidazole membranes: physiochemical characterization and fuel cell applications,” Journal of Applied Electrochemistry, vol. 31, no. 7, pp. 773–779, 2001.
View at: Publisher Site | Google Scholar
N. H. Jalani, M. Ramani, K. Ohlsson et al., “Performance analysis and impedance spectral signatures of high temperature PBI-phosphoric acid gel membrane fuel cells,” Journal of Power Sources, vol. 160, no. 2, pp. 1096–1103, 2006.
View at: Publisher Site | Google Scholar
Q. Li, R. He, J.-A. Gao, J. O. Jensen, and N. J. Bjerrum, “The CO poisoning effect in PEMFCs operational at temperatures up to 200°C,” Journal of the Electrochemical Society, vol. 150, no. 12, pp. A1599–A1605, 2003.
View at: Publisher Site | Google Scholar
U. Gardemann, M. Steffen, and A. Heinzel, “Design and demonstration of an ethanol fuel processor for HT-PEM fuel cell applications,” International Journal of Hydrogen Energy, vol. 39, no. 31, pp. 18135–18145, 2014.
View at: Publisher Site | Google Scholar
M. Maximini, P. Engelhardt, M. Brenner, F. Beckmann, and O. Moritz, “Fast start-up of a diesel fuel processor for PEM fuel cells,” International Journal of Hydrogen Energy, vol. 39, no. 31, pp. 18154–18163, 2014.
View at: Publisher Site | Google Scholar
R. C. Samsun, C. Krupp, A. Tschauder, R. Peters, and D. Stolten, “Electrical start-up for diesel fuel processing in a fuel-cell-based auxiliary power unit,” Journal of Power Sources, vol. 302, pp. 315–323, 2016.
View at: Publisher Site | Google Scholar
S. Authayanun, W. Wiyaratn, S. Assabumrungrat, and A. Arpornwichanop, “Theoretical analysis of a glycerol reforming and high-temperature PEMFC integrated system: hydrogen production and system efficiency,” Fuel, vol. 105, pp. 345–352, 2013.
View at: Publisher Site | Google Scholar
A. Perna, S. P. Cicconardi, and R. Cozzolino, “Performance evaluation of a fuel processing system based on membrane reactors technology integrated with a PEMFC stack,” International Journal of Hydrogen Energy, vol. 36, no. 16, pp. 9906–9915, 2011.
View at: Publisher Site | Google Scholar
S. Authayanun, M. Mamlouk, K. Scott, and A. Arpornwichanop, “Comparison of high-temperature and low-temperature polymer electrolyte membrane fuel cell systems with glycerol reforming process for stationary applications,” Applied Energy, vol. 109, pp. 192–201, 2013.
View at: Publisher Site | Google Scholar
E. Jannelli, M. Minutillo, and A. Perna, “Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances,” Applied Energy, vol. 108, pp. 82–91, 2013.
View at: Publisher Site | Google Scholar
A. Arsalis, M. P. Nielsen, and S. K. Kær, “Modeling and off-design performance of a 1kWe HT-PEMFC (high temperature-proton exchange membrane fuel cell)-based residential micro-CHP (combined-heat-and-power) system for Danish single-family households,” Energy, vol. 36, no. 2, pp. 993–1002, 2011.
View at: Publisher Site | Google Scholar
N. Zuliani and R. Taccani, “Microcogeneration system based on HTPEM fuel cell fueled with natural gas: performance analysis,” Applied Energy, vol. 97, pp. 802–808, 2012.
View at: Publisher Site | Google Scholar
B. Najafi, A. Haghighat Mamaghani, A. Baricci, F. Rinaldi, and A. Casalegno, “Mathematical modelling and parametric study on a 30 kWel high temperature PEM fuel cell based residential micro cogeneration plant,” International Journal of Hydrogen Energy, vol. 40, no. 3, pp. 1569–1583, 2015.
View at: Publisher Site | Google Scholar
A. M. Rabiu, N. Dlangamandla, and Ø. Ulleberg, “Novel heat integration in a methane reformer and high temperature PEM fuel cell-based mCHP system,” APCBEE Procedia, vol. 3, pp. 17–22, 2012.
View at: Publisher Site | Google Scholar
A. Arsalis, M. P. Nielsen, and S. K. Kær, “Optimization of a high temperature PEMFC micro-CHP system by formulation and application of a process integration methodology,” Fuel Cells, vol. 13, no. 2, pp. 238–248, 2013.
View at: Publisher Site | Google Scholar
A. Arsalis, S. K. Kær, and M. P. Nielsen, “Modeling and optimization of a heat-pump-assisted high temperature proton exchange membrane fuel cell micro-combined-heat-and-power system for residential applications,” Applied Energy, vol. 147, pp. 569–581, 2015.
View at: Publisher Site | Google Scholar
B. Najafi, A. Haghighat Mamaghani, F. Rinaldi, and A. Casalegno, “Long-term performance analysis of an HT-PEM fuel cell based micro-CHP system: operational strategies,” Applied Energy, vol. 147, pp. 582–592, 2015.
View at: Publisher Site | Google Scholar
N. Briguglio, M. Ferraro, G. Brunaccini, and V. Antonucci, “Evaluation of a low temperature fuel cell system for residential CHP,” International Journal of Hydrogen Energy, vol. 36, no. 13, pp. 8023–8029, 2011.
View at: Publisher Site | Google Scholar
J. Xu and G. F. Froment, “Methane steam reforming, methanation and water-gas shift: I. Intrinsic kinetics,” AIChE Journal, vol. 35, no. 1, pp. 88–96, 1989.
View at: Publisher Site | Google Scholar
G.-Y. Kim, J. R. Mayor, and J. Ni, “Parametric study of microreactor design for water gas shift reactor using an integrated reaction and heat exchange model,” Chemical Engineering Journal, vol. 110, no. 1–3, pp. 1–10, 2005.
View at: Publisher Site | Google Scholar
R. W. Schefer, “Catalyzed combustion of H2/air mixtures in a flat plate boundary layer: II. Numerical model,” Combustion and Flame, vol. 45, pp. 171–190, 1982.
View at: Publisher Site | Google Scholar
X. Song, W. R. Williams, L. D. Schmidt, and R. Aris, “Ignition and extinction of homogeneous-heterogeneous combustion: CH₄ and C₃H₈ oxidation on PT,” Symposium (International) on Combustion, vol. 23, no. 1, pp. 1129–1137, 1991.
View at: Publisher Site | Google Scholar
N. W. Cant, P. C. Hicks, and B. S. Lennon, “Steady-state oxidation of carbon monoxide over supported noble metals with particular reference to platinum,” Journal of Catalysis, vol. 54, no. 3, pp. 372–383, 1978.
View at: Publisher Site | Google Scholar
K. Jiao, I. E. Alaefour, and X. Li, “Three-dimensional non-isothermal modeling of carbon monoxide poisoning in high temperature proton exchange membrane fuel cells with phosphoric acid doped polybenzimidazole membranes,” Fuel, vol. 90, no. 2, pp. 568–582, 2011.
View at: Publisher Site | Google Scholar
K. Scott and M. Mamlouk, “A cell voltage equation for an intermediate temperature proton exchange membrane fuel cell,” International Journal of Hydrogen Energy, vol. 34, no. 22, pp. 9195–9202, 2009.
View at: Publisher Site | Google Scholar
D. F. Cheddie and N. D. H. Munroe, “A two-phase model of an intermediate temperature PEM fuel cell,” International Journal of Hydrogen Energy, vol. 32, no. 7, pp. 832–841, 2007.
View at: Publisher Site | Google Scholar
T. Sousa, M. Mamlouk, and K. Scott, “An isothermal model of a laboratory intermediate temperature fuel cell using PBI doped phosphoric acid membranes,” Chemical Engineering Science, vol. 65, no. 8, pp. 2513–2530, 2010.
View at: Publisher Site | Google Scholar
H. P. Dhar, L. G. Christner, A. K. Kush, and H. C. Maru, “Performance study of a fuel cell Pt-on-C anode in presence of CO and CO₂ and calculation of adsorption parameters for CO poisoning,” Journal of the Electrochemical Society, vol. 133, no. 8, pp. 1574–1582, 1986.
View at: Publisher Site | Google Scholar
PSE, “gPROMS ModelBuilder v3.6,” 2015, http://www.psenterprise.com/.
View at: Google Scholar
P. Bujlo, S. Pasupathi, Ø. Ulleberg et al., “Validation of an externally oil-cooled 1 kWel HT-PEMFC stack operating at various experimental conditions,” International Journal of Hydrogen Energy, vol. 38, no. 23, pp. 9847–9855, 2013.
View at: Publisher Site | Google Scholar
D. Di Bona, E. Jannelli, M. Minutillo, and A. Perna, “Investigations on the behaviour of 2 kW natural gas fuel processor,” International Journal of Hydrogen Energy, vol. 36, no. 13, pp. 7763–7770, 2011.
View at: Publisher Site | Google Scholar
U. H. Jung, W. Kim, K. Y. Koo, and W. L. Yoon, “Genuine design of compact natural gas fuel processor for 1-kWe class residential proton exchange membrane fuel cell systems,” Fuel Processing Technology, vol. 121, pp. 32–37, 2014.
View at: Publisher Site | Google Scholar
C.-B. Lee, S.-H. Cho, D.-W. Lee, K.-R. Hwang, J.-S. Park, and S.-H. Kim, “Combination of preferential CO oxidation and methanation in hybrid MCR (micro-channel reactor) for CO clean-up,” Energy, vol. 78, pp. 421–425, 2014.
View at: Publisher Site | Google Scholar
A. Ersöz and A. Sayar, “A process simulation study of a newly designed fuel processing system for a high temperature PEM fuel cell unit,” International Journal of Hydrogen Energy, vol. 40, no. 42, pp. 14469–14482, 2015.
View at: Publisher Site | Google Scholar
A. Arsalis, M. P. Nielsen, and S. K. Kær, “Modeling and parametric study of a 1 kWe HT-PEMFC-based residential micro-CHP system,” International Journal of Hydrogen Energy, vol. 36, no. 8, pp. 5010–5020, 2011.
View at: Publisher Site | Google Scholar
J. Kupecki, “Off-design analysis of a micro-CHP unit with solid oxide fuel cells fed by DME,” International Journal of Hydrogen Energy, vol. 40, no. 35, pp. 12009–12022, 2015.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2016 Myalelo Nomnqa et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

4740

Downloads

1743

Citations