Electrochemical Synthesis of Polyaniline/Poly-<i>O</i>-Aminophenol Copolymers in Chloride Medium

Mascaro, Lucia H.; Berton, Alessandra N.; Micaroni, Liliana

doi:https://doi.org/10.4061/2011/292581

International Journal of Electrochemistry

On this page

Abstract Introduction Experimental Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2011 | Article ID 292581 | https://doi.org/10.4061/2011/292581

Electrochemical Synthesis of Polyaniline/Poly-O-Aminophenol Copolymers in Chloride Medium

Lucia H. Mascaro,¹Alessandra N. Berton,²and Liliana Micaroni²

Academic Editor: Hamilton Varela

Received11 Jan 2011

Revised21 Apr 2011

Accepted30 Apr 2011

Published28 Jun 2011

Abstract

The copolymerization of o-aminophenol (OAP) and aniline (ANI) on Pt and ITO electrodes was studied using cyclic voltammetry in 0.1 M HCl/0.4 M NaCl solution. The films were characterized by SEM, cyclic voltammetry, and UV-Vis spectroscopy. The properties of the copolymer were compared with PANI and POAP films. The results strongly suggest that the growth of PANI-POAP films does not consist of the simple buildup of layers of homopolymers on the electrode surface as a result of OAP or ANI oxidation products in the monomer mixture, but that a new conducting polymer is formed by copolymerization.

1. Introduction

The polymerization of substituted anilines has been studied with an aim to achieve the formation of soluble polymeric films in order to improve processability while maintaining electric properties [1]. However, the electropolymerization of benzyl monomers containing both −NH₃ and −OH groups is more recent and less well explored [2]. O-aminophenol monomer (OAP) is an aniline derivative that has been shown to hold two groups in the benzenic ring: an amine and a hydroxyl group, which supply many more coordination sites [2]. There is controversy in the literature with regard to dimeric structures formed after chemical and electrochemical oxidation of OAP in aqueous medium. Electrophilic reactions may occur at the meta or para position of the −NH₂ group of OAP, yielding two types of heteroaminic. structures. While chemical oxidation of OAP yields the formation of 2-aminophenoxazine (APZ) [3–6], redox reactions involving the B structure (phenoxazine units) have been proposed for electrochemically prepared POAP films [7–10] (Scheme 1).

However, most conducting polymers suffer from some limitations. For example, polyaniline (PANI) with alkyl substituents presents limitations that are imposed on the conductivity of the produced polymer despite its solubility being improved when compared with PANI. Efforts have been made towards the design of new conducting materials. In this way, the conductivity of polyanilines and the solubility of substituted polyanilines can be achieved by copolymerization [11].

Copolymerization allows chemical modification as well as the introduction of specific functional groups to side substituents to control the physicochemical properties of materials [12]. The copolymerizations of sulfonated aniline and aniline have been successfully carried out [13–15]. There are many examples of polyaniline-type copolymers: copolymers of aniline and o-toluidine [16–18], aniline and 2-ethylaniline [11], aniline and o-anisidine [17, 19], aniline and o- and m-phenylenediamine [20, 21], aniline and N-butylaniline [22], aniline and o-alkoxysulfonated 23, aniline and pyrrole [23], and aniline and thiophene 25. These various copolymers are synthesized under different conditions, by chemical or electrochemical methods, in order to achieve the desired properties.

In 2002, the first studies of the copolymerization of OAP and PANI appeared with the objectives mainly being to improve the solubility of PANI and the electric conductivity of POAP. In recent years, many other works have been published in order to study the different properties of this copolymer [24–26]. Hua and Ruckenstein [27] synthesized a novel water-soluble copolymer of aniline and aminophenol (AP) grafted with oligo-(oxyethylene) (PEO) side chains (AP-g-PEO). The copolymerization and copolymer compositions were changed using various feed mole ratios AP-g-PEO/aniline and oligo-(oxyethylene) side-chain lengths. The copolymer of poly((AP-g-PEO-750-co-aniline) with a feed mole ratio of 3/1 was water-soluble and exhibited relatively high conductivity (0.12 S/cm). Several authors have observed that the monomer concentration ratio, acid concentration, and applied potential strongly affect the copolymerization rate and the properties of the copolymer [27–29]. Zhang et al. [28] concluded that optimal conditions for the copolymerization involve the scan potential range being controlled between −0.10 and 0.95 V (versus SCE), with a solution consisting of 0.34 M aniline, 0.012 M m-aminophenol, and 2.0 M H₂SO₄. A nanostructured network of poly(aniline-co-o-aminophenol) has been synthesized in the presence of ferrocenesulfonic acid, and fiber size in the nanostructures can be controlled by the number of cycles during copolymerization [30]. Also found in the literature are applications of these copolymers as sensors of uricase [31], arsenate [32], cathecol [33], hydrogen peroxide [34], and ascorbic acid [35]. However, the studies found in the literature involve the synthesis of PANI-POAP copolymer from sulfuric acid solution, whereas in this paper we propose synthesis from HCl + NaCl solution and the comparison of these films with their homopolymers.

2. Experimental

Grade aniline (Merck) was distilled and the resulting colorless liquid was kept in the dark at 5°C. OAP (Aldrich) was recrystallized in PA ethyl acetate, dried, and stored in a vacuum. Electrolyte solutions were prepared from PA reagents and double-distilled water. Electrochemical synthesis and cyclic voltammetric studies were performed by using Microquímica MQPG 01 with general-purpose electrochemical system software. A three-electrode cell was used with an Ag/AgCl electrode acting as reference electrode and a platinum wire serving as counter electrode. A platinum foil of area 1 cm² was used as working electrode.

For the electrochemical copolymerization studies, a mixture of ANI and OAP was used in 0.1 M HCl and 0.4 M NaCl. The monomer concentrations used for growth of the homo- and copolymers were 0.1 M ANI, 0.001 M OAP, and 0.1 M ANI-0.001 OAP, respectively.

Electropolymerization was achieved by sweeping the potentials in the range from −0.2 to 1.0 V for several cycles with a sweep rate of 50 mV s, and the cyclic voltammogramms (CVs) were recorded simultaneously with the synthesis. The polymer/copolymer film-coated electrode was then placed in a monomer-free background electrolyte (0.1 M HCl and 0.4 M NaCl), and CVs of the film-coated electrode were recorded after obtaining the stable cyclic voltammetric pattern.

A Shimadzu 2401 PC UV-Vis spectrophotometer was used to record the UV-Vis spectra of PANI, POAP, and PANI-POAP films deposited onto an indium-doped tin oxide (ITO) glass electrode. Polymerization was carried out in the conditions specified above. Before all measurements were taken, the deposited polymer films on the electrode (which were extracted from the solution in the reduced state) were washed with 0.1 M HCl and dried in a vacuum for 24 hrs. Surface morphology of these films were examined by a Philips XL-30 scanning electron microscope (SEM). The FTIR spectra of the PANI and PANI-POAP film samples were taken using a Nicolet Impact 410 FTIR spectrophotometer.

3. Results and Discussion

3.1. Electrochemical Polymerization of Aniline, O-Aminophenol, and Its Copolymer

Solutions consisting of 0.1 M aniline, 1 mM o-aminophenol, and 0.1 M aniline + 1 mM o-aminophenol in 0.1 M HCl/0.4 M NaCl solutions were used for polymerization of the homo- and copolymers, respectively. The polymerization and copolymerization of monomers were performed by using repeated potential cycling at a scan rate of 20 mV s. Figures 1(a)–1(c) show the typical cyclic voltammogramms recorded during electrochemical synthesis of the polymer in the presence of ANI, OAP, and ANI/OAP, respectively.

(a)

(b)

(c)

Typical CVs indicative of pure ANI polymerization are shown in Figure 1(a). During the anodic sweep, an anodic peak at 1.1 V appears in the first cycle, and then three anodic peaks (I_a, II_a, III_a) appear in subsequent cycles. In the cathodic sweep, the presence of three corresponding broad reduction peaks is labeled: I_b, II_b, and III_b. Their peak currents increase quickly with an increase in the number of potential cycles. This indicates that polyaniline film grows very quickly as the electrolysis proceeds, which is caused by autocatalytic polymerization [36, 37]. The peaks can be attributed to: regarding the first peak at 0.2 V (peak I_a), formation of radical cations (polaronic emeraldine); regarding the second, benzoquinone formation, occurring at 0.5 V (peak II_a); and regarding the third, formation of diradical dications, commencing at approximately 0.6 V and reaching a maximum at 0.75 V (peak III_a) [38]. After electrolysis, a green film was formed on the working electrode after 15 cycles.

Figure 1(b) shows the electro-oxidation of OAP when cycling the potential between −0.2 and 1.10 V at scan rate 50 mV s. Initially, two redox couples were observed. The anodic peaks were found at 0.31 V (peak II_a) and at 0.62 V (peak III_a), and the corresponding two cathodic peaks at 0.27 (peak II_c) and 0.59 (peak III_c). A redox pair at 0.12 V/0.04 V (I_a/I_c) began to appear after a few scans and the current increase during continuous cycles. According to Barbero et al. [7], peaks a₂ and a₃ were due to the oxidation of OAP to the radical cation (OAP^•+) and its further oxidation to the dication, respectively. By contrast, peak a₁ only resulted from the formation of radical cations (POAP^•+) from the polymer and/or oligomers. On further potential cycling, the oxidation current (peaks II_a and III_a) decreases rapidly owing to the low conductivity of POAP, which hinders the diffusion of OAP through the polymer matrix [7, 37]. The redox peaks I_a1/I_c nonetheless increased steadily with an increasing number of scans, showing the gradual yet continual formation of electroactive POAP films. In contrast to PANI deposition, POAP films formed very slowly, and only after 90 cycles was a thin film found on the working electrode. It changed color from dark brown in the oxidized state to light yellow in the reduced state.

Like the homopolymerization of OAP and ANI, electrolysis of mixed solutions containing both OAP and ANI was carried out by cycling the potential between −0.20 V and different upper potential limits. Cyclic voltammogramms recorded during potentiodynamic copolymerization on a Pt electrode of ANI with OAP for 0.1 M HCl + 0.4 M NaCl + 0.1 M ANI + 1 mM OAP are shown in Figure 1(c). A close comparison of these CVs reveals that voltammetric curves of copolymers are more distinct than homopolymers, indicating that the film deposited during oxidation of the ANI + OAP mixture is different from that of ANI or OAP oxidation. The PANI-POAP film deposited is brownish-blue which is different from the color of both homopolymers, and it can be observed after 20° cycles, which is a shorter time than that obtained for POAP alone.

In Figure 1(c), an anodic peak appears at 1.05 V for the first cycle. This peak is caused by the oxidation of amino groups from both monomers, since the ANI oxidation peak is at 1.1 V (Figure 1(a)) and oxidation of OAP occurs near 0.9 V (Figure 1(b)). In successive sweeps, there are three anodic peaks, with a shoulder at 0.2 V, and four cathodic peaks. The fact that there are four cathodic peaks on the reverse scan of the first cycle is a first indication that the deposition in this case is different from that of POAP and ANI.

After several cycles, four main redox pairs were observed and the current of redox peaks gradually increased with the number of cycles. The voltammetric behavior is different from that of PANI growth, with an additional redox pair (IV_a/IV_c) present at 0.28/0.26 V. This extra pair of redox peaks would be caused by redox of the copolymer itself. This observation strongly suggests that the growth of PANI-POAP film does not consist of the simple buildup of layers on the electrode surface as a result of ANI or OAP oxidation products in the monomer mixture, but that a new conductor polymer is formed. The same behavior was observed by different authors in sulfuric acid [27–30].

In Figure 1(c), it can also be observed that the redox peaks I_a/I_c are smaller than those observed in the same potential in Figure 1(a) (peaks I_a/I_c). The peaks II_a/II_c become more prominent in Figure 1(c) than in Figure 1(a). These results indicate an easier redox reaction of polyaniline side chains [38], which overlap the peak of benzoquinone formation. The broader anodic peak III_a is observed at 0.58 V, which is related to the overlap of peak III_a of Figure 1(a) and peak IIIa of Figure 1(c). The current density of peak III_a is larger than that of peak III_a of Figure 1(b), indicating that OAP is easily oxidized to the radical cation (OAP^.+).

3.2. Voltammetric Responses of PANI, POAP, and Its Copolymer

The voltammetric responses of PANI, POAP, and PANI-POAP films deposited on a Pt electrode were recorded in the supporting electrolyte (0.1 M HCl and 0.4 M NaCl), Figure 3. The CVs of the response and formation of polymer films are similar. In the case of POAP, the peak a₃ observed in Figure 1(b) disappears completely, indicating that formation of radical cations (polarons) and dications (bipolarons) was not achieved in the polymer due to the difficulty in charge and electron delocalization along POAP polymer chains, which are known to be partly cross-linked [7].

The PANI films showed a typical redox response with three redox couples, as reported in the literature [39, 40]. The first and third redox couples are due to the interconversion reactions of PANI upon varying the potential (leucoemeraldine/emeraldine and emeraldine/pernigraniline, respectively). The middle peaks have been assigned to redox reactions involving an overoxidized PANI structure, indicating polymer degradation.

For PANI-POAP films, the CVs of response and polymerization are similar and both present four redox couples as previously discussed. However, by comparing the three curves present in Figure 2, it is possible to observe different responses for the three films that are deposited. The redox processes attributed to the PANI film shift for cathodic and anodic values. This behavior again suggests that copolymer formation has taken place.

3.3. UV-Vis of PANI, POAP, and Its Copolymer Films

Figure 3 shows UV-Vis spectra of PANI, POAP, and PANI-POAP films on ITO electrodes recorded in HCl 0.1 M and NaCl 0.4 M. The films were deposited in the same conditions shown in Figure 1.

PANI film presents UV-Vis spectra characteristic of the emeraldine base. There are three absorption bands at 317, 457, and 647 nm, which is a broad band. Bands with peaks at 317 and 457 nm correspond to the transitions in the benzonoid rings, while the band at 647 nm is usually ascribed to an exciton, located in the quinoid ring [41].

The absorption spectrum of the oxidized form of POAP presents two absorption bands with peaks at 309 and 457 nm, which correspond to the transitions of the aromatic structure and the oxidized form of OAP [7], respectively. The band at 457 nm can also be attributed to the phenoxazine of the polymer [7].

The UV-Vis spectrum of the copolymer shows the same bands observed for the PANI and POAP films, indicating that the same transitions observed in homopolymers occur in the copolymer. The UV-Vis spectrum of the copolymer is similar to that obtained for POAP films since both present a brown color. On the other hand, the absorbance of the band at 457 nm, which corresponds to the formation of the intermediate state during the electrooxidation of the leucoemeraldine state, presents a higher intensity when compared with that observed for the homopolymers. The absorption band at about 317 nm for PANI shifts to about 303 nm for PANI-POAP films. This shift can be caused by the presence of the substituent−OH groups in the copolymer chain. The absorption results obtained from electrochemical polymerization of the mixture of ANI and OAP clearly show the incorporation of OAP into the polymer during polymerization.

3.4. FTIR of PANI and PANI-POAP

To investigate the copolymerization of ANI and OAP, FTIR and UV-Vis absorption spectra were also employed to characterize the structure of PANI-POAP. Figure 4 shows the FTIR spectrum of PANI-POAP (curve 1), and for comparison, the FTIR spectrum of PANI (curve 2).

As seen in Figure 4, the FTIR spectra of copolymers seem to present the same picture as that of PANI, indicating that aniline units dominate the composition of the copolymer. However, there are some differences between curves 1 and 2. This suggests that the copolymer chain is somewhat different from the polyaniline chain, since the former contains OAF. A peak at 1383 cm, which appears on curve 2 but not on curve 1, may be attributed to the C–O–H deformation vibrations, since a peak at 1400 cm appears in the IR spectrum of o-aminophenol [35] and the IR spectra of phenols have an absorption peak at 1390–1310 cm [36]. Thus, the peak at 1383 cm in Figure 4 can be considered as evidence of the presence of the OAP unit in the polymer film. We can also notice that the two split peaks at 1210 and 1230 cm are observed in the IR spectrum of o-aminophenol [35], which may be attributed to the C–O stretching vibrations. However, only a very small shoulder at 1214 cm appears in Figure 4. This is due to the fact that a broad band centered at 1288 cm may mask the C–O stretching vibrations.

The other peaks observed for both PANI and PANI-POAP films can be attributed as follows: the peaks at 1583 and 1483 cm are attributed to the C=C stretching vibrations of the benzene ring and quinone ring vibrations [37, 38, 42]. The peak at 1303 cm is due to the C–N stretching of the polymer. The strongest band observed near 1100 cm and the band at 1235 cm are due to C–C stretching and C–C twisting, respectively, of the alkyl chain [43]. The peak near 800 cm is due to the N–H out-of-plane bending absorption. The C–Cl stretching peak arises in the range of 590–700 cm [44]. This confirmed the Cl-doping of the electrochemically synthesized polyaniline films in HCl.

3.5. Morphology of the PANI, POAP, and Its Copolymer Films

The images of PANI, POAP, and copolymer films are shown in Figure 5. The deposits of polymers were obtained on ITO electrodes in the same conditions as the UV-Vis spectra.

(a)

(b)

(c)

PANI exhibits a fibrous structure in Figure 5(a) and the fibrous deposit is not entirely uniform over the electrode, indicating that the fibers are preferred sites for further polymer growth. As can be seen, POAP films present a highly compact structure (Figure 5(b)). The SEM image of the PANI-POAP film, in Figure 5(c), reveals uniform films, which completely recover the surface, and a dense fine granular deposit. The change in surface structure indicates the strong effect of ANI units on the copolymer morphology.

4. Conclusions

The CVs of OAP-ANI copolymerization, on a Pt electrode, were compared with CVs for ANI and OAP polymerization. For ANI-OAP polymerization, four main redox pairs were observed and the current of redox peaks gradually increased with the number of cycles, indicating the growth of conducting polymer film in each cycle. However, for ANI polymerization, three characteristic redox pairs were recorded, whereas for the CV of OAP polymerization, only two redox pairs were marked. The color of the oxidized polymers varies; PANI-POAP film is brownish-blue and PANI film is green, while POAP film is brown. Based on the fact that the cyclic voltammogram of the resulting polymer is not a simple superposition of each individual polymer, and the color of the resulting polymer is different from that of PANI and POAP, we can conclude that the resulting polymer obtained from electrolysis of the solution consisting of ANI and OAP is a copolymer, rather than a mixture of PANI and POAP.

Furthermore, differences in UV-Vis spectra can be noticed between the three films favoring the incorporation of OAP units in the copolymer. SEM analysis showed a change in morphology, from fibrous PANI films to dense fine granular PANI-POAP films, indicating the strong effect of ANI units on the copolymer morphology. The FTIR spectrum of PANI-POAP indicates that an electrochemical copolymerization of ANI and OAP took place in this study.

Copolymerization of ANI and OAP has been used as a good electrochemical sensor for different samples, and our preliminary results show that the material has electroluminescent properties, and it could, therefore, be used in polymer-based light-emitting diodes.

Acknowledgments

The authors are indebted to the Brazilian agencies CAPES, CNPq, and Araucária Foundation. The authors also wish to thank Mr. M. A. C. Berton and Mrs. Laiz Valgas de Castilhos of LACTEC for providing technical support in SEM experiments.

References

D. Gonçalves, R. C. Faria, M. Yonashiro, and L. O. S. Bulhões, “Electrochemical oxidation of o-aminophenol in aqueous acidic medium: formation of film and soluble products,” Journal of Electroanalytical Chemistry, vol. 487, no. 2, pp. 90–99, 2000.
View at: Publisher Site | Google Scholar
J. M. Ortega, “Conducting potential range for poly(o-aminophenol),” Thin Solid Films, vol. 371, no. 1-2, pp. 28–35, 2000.
View at: Google Scholar
T. Nogami, T. Hishida, M. Yamada, H. Mikawa, and Y. Shirota, “Formations and reactions of o-benzoquinone mono- and di-imines. I.,” Bulletin of the Chemical Society of Japan, vol. 48, no. 12, pp. 3709–3714, 1975.
View at: Google Scholar
V. Balogh, M. Fétizon, and M. Golfier, “Oxidations with silver carbonate/celite. V. Oxidations of phenols and related compounds,” Journal of Organic Chemistry, vol. 36, no. 10, pp. 1339–1341, 1971.
View at: Google Scholar
R. G. Srivastava, R. L. Pandeyo, and P. S. Venkataramani, “Highly soluble conducting poly(ethylene oxide) grafted at two sites of poly(o-aminobenzyl alcohol),” Indian Journal of Chemistry B, vol. 20B, p. 995, 1981.
View at: Google Scholar
S. Kunimura, T. Ohsaka, and N. Oyama, “Preparation of thin polymeric films on electrode surfaces by electropolymerization of o-aminophenol,” Macromolecules, vol. 21, no. 4, pp. 894–900, 1988.
View at: Google Scholar
C. Barbero, J. J. Silber, and L. Sereno, “Formation of a novel electroactive film by electropolymerization of ortho-aminophenol. Study of its chemical structure and formation mechanism. Electropolymerization of analogous compounds,” Journal of Electroanalytical Chemistry, vol. 263, no. 2, pp. 333–352, 1989.
View at: Google Scholar
A. Q. Zhang, C. Q. Cui, Y. Z. Chen, and J. Y. Lee, “Synthesis and electrochromic properties of poly-o-aminophenol,” Journal of Electroanalytical Chemistry, vol. 373, no. 1-2, pp. 115–121, 1994.
View at: Google Scholar
R. I. Tucceri, C. Barbero, J. J. Silber, L. Sereno, and D. Posadas, “Spectroelectrochemical study of poly-o-aminophenol,” Electrochimica Acta, vol. 42, no. 6, pp. 919–927, 1997.
View at: Google Scholar
R. M. Torresi, S. I. C. de Torresi, C. Gabrielli, M. Keddam, and H. Takenouti, “Quartz crystal microbalance characterization of electrochemical doping of polyaniline films,” Synthetic Metals, vol. 61, no. 3, pp. 291–296, 1993.
View at: Google Scholar
A. L. Schemid, L. M. Lira, and S. I. Córdoba de Torresi, “On the electrochemical and spectroscopic properties of a soluble polyaniline parent copolymer,” Electrochimica Acta, vol. 47, no. 12, pp. 2005–2011, 2002.
View at: Publisher Site | Google Scholar
H. Kaczmarek and W. Czerwiński, “The influence of polychromatic UV-irradiation on new thiophene copolymers,” Journal of Photochemistry and Photobiology A, vol. 146, no. 3, pp. 207–218, 2002.
View at: Google Scholar
Q. Yang, Y. Zhang, H. Li et al., “Electrochemical copolymerization study of o-toluidine and o-aminophenol by the simultaneous EQCM and in situ FTIR spectroelectrochemisty,” Talanta, vol. 81, no. 1-2, pp. 664–672, 2010.
View at: Publisher Site | Google Scholar
B. C. Roy, M. D. Gupta, L. Bhoumik, and J. K. Ray, “Spectroscopic investigation of water-soluble polyaniline copolymers,” Synthetic Metals, vol. 130, no. 1, pp. 27–33, 2002.
View at: Publisher Site | Google Scholar
R. G. Srivastava, R. L. Pandeyo, and P. S. Venkataramani, “Barium manganate oxidation in organic-synthesis. 1.oxidation of aromatic primary amines,” Indian Journal of Chemistry Section B, vol. 20, p. 995, 1981.
View at: Google Scholar
D. D. Borole, U. R. Kapadi, P. P. Kumbhar, and D. G. Hundiwale, “Influence of inorganic and organic supporting electrolytes on the electrochemical synthesis of polyaniline, poly(o-toluidine) and their copolymer thin films,” Materials Letters, vol. 56, no. 5, pp. 685–691, 2002.
View at: Publisher Site | Google Scholar
M. K. Ram, E. Maccioni, and C. Nicolini, “The electrochromic response of polyaniline and its copolymeric systems,” Thin Solid Films, vol. 303, no. 1-2, pp. 27–33, 1997.
View at: Google Scholar
C.-H. Yang, Journal of Electroanalytical Chemistry, vol. 71, p. 459, 1998.
M. K. Ram, N. Sarkar, H. Ding, and C. Nicolini, “Synthesis of controlled copolymerisation of aniline and ortho-anisidine: a physical insight in its Langmuir-Schaefer films,” Synthetic Metals, vol. 123, no. 2, pp. 197–206, 2001.
View at: Publisher Site | Google Scholar
R. Mazeikiene and A. Malinauskas, “Electrochemical copolymerization of aniline with m-phenylenediamine,” Synthetic Metals, vol. 92, no. 3, pp. 259–263, 1998.
View at: Google Scholar
A. Malinauskas, M. Bron, and R. Holze, “Electrochemical and Raman spectroscopic studies of electrosynthesized copolymers and bilayer structures of polyaniline and poly(o-phenylenediamine),” Synthetic Metals, vol. 92, no. 2, pp. 127–137, 1998.
View at: Google Scholar
S. Ye, N. T. Do, L. H. Dao, and A. K. Vijh, “Electrochemical preparation and characterization of conducting copolymers: poly (aniline-co-N-butylaniline),” Synthetic Metals, vol. 88, no. 1, pp. 65–72, 1997.
View at: Google Scholar
B. Sari and M. Talu, “Electrochemical copolymerization of pyrrole and aniline,” Synthetic Metals, vol. 94, no. 2, pp. 221–227, 1998.
View at: Google Scholar
Y. Zhang, S. Mu, and J. Zhai, “Nanostructured poly(aniline-co-2,4-diaminophenol) synthesized via chemical copolymerization and the properties of the resulting copolymer,” Synthetic Metals, vol. 159, no. 17-18, pp. 1844–1851, 2009.
View at: Publisher Site | Google Scholar
S. Mu, Y. Zhang, and J. Zhai, “The electrochemical copolymerization of aniline with 2,4-diaminophenol and the electric properties of the resulting copolymer,” Electrochimica Acta, vol. 54, no. 15, pp. 3923–3929, 2009.
View at: Publisher Site | Google Scholar
J. Zhang, D. Shan, and S. Mu, “Chemical synthesis and electric properties of the conducting copolymer of aniline and o-aminophenol,” Journal of Polymer Science, Part A, vol. 45, no. 23, pp. 5573–5582, 2007.
View at: Publisher Site | Google Scholar
F. Hua and E. Ruckenstein, “Copolymers of aniline and 3-aminophenol derivatives with oligo(oxyethylene) side chains as novel water-soluble conducting polymers,” Macromolecules, vol. 37, no. 16, pp. 6104–6112, 2004.
View at: Publisher Site | Google Scholar
J. Zhang, D. Shan, and S. Mu, “Electrochemical copolymerization of aniline with m-aminophenol and novel electrical properties of the copolymer in the wide pH range,” Electrochimica Acta, vol. 51, no. 20, pp. 4262–4270, 2006.
View at: Publisher Site | Google Scholar
S. Mu, “Electrochemical copolymerization of aniline and o-aminophenol,” Synthetic Metals, vol. 143, no. 3, pp. 259–268, 2004.
View at: Publisher Site | Google Scholar
S. Mu, “Poly(aniline-co-o-aminophenol) nanostructured network: electrochemical controllable synthesis and electrocatalysis,” Electrochimica Acta, vol. 51, no. 17, pp. 3434–3440, 2006.
View at: Publisher Site | Google Scholar
X. Pan, S. Zhou, C. Chen, and J. Kan, “Preparation and properties of an uricase biosensor based on copolymer of o-aminophenol-aniline,” Sensors and Actuators, B, vol. 113, no. 1, pp. 329–334, 2006.
View at: Publisher Site | Google Scholar
S. Mu, “Direct determination of arsenate based on its electrocatalytic reduction at the poly(aniline-co-o-aminophenol) electrode,” Electrochemistry Communications, vol. 11, no. 7, pp. 1519–1522, 2009.
View at: Publisher Site | Google Scholar
D. E. Stilwell and S. M. Park, “Electrochemistry of conductive polymers. II. Electrochemical studies on growth properties of polyaniline,” Journal of the Electrochemical Society, vol. 135, no. 9, pp. 2254–2262, 1988.
View at: Google Scholar
C. Chen, C. Sun, and Y. Gao, “Application of electrosynthesized poly(aniline-co-p-aminophenol) as a catechol sensor,” Electrochimica Acta, vol. 54, no. 9, pp. 2575–2580, 2009.
View at: Publisher Site | Google Scholar
C. Chen, C. Sun, and Y. Gao, “Amperometric sensor for hydrogen peroxide based on poly(aniline-co-p-aminophenol),” Electrochemistry Communications, vol. 11, no. 2, pp. 450–453, 2009.
View at: Publisher Site | Google Scholar
D. E. Stilwell and SU. M. Park, “Electrochemistry of conductive polymers. II. Electrochemical studies on growth properties of polyaniline,” Journal of the Electrochemical Society, vol. 135, no. 9, pp. 2254–2262, 1988.
View at: Google Scholar
C. H. Yang and T. C. Wen, “Polyaniline derivative with external and internal doping via electrochemical copolymerization of aniline and 2,5-diaminobenzenesulfonic acid on IrO-coated titanium electrode,” Journal of the Electrochemical Society, vol. 141, no. 10, pp. 2624–2632, 1994.
View at: Google Scholar
K. Naoi, K. I. Kawase, M. Mori, and M. Komiyama, “Electrochemistry of poly(2,2'-dithiodianiline): a new class of high energy conducting polymer interconnected with S-S bonds,” Journal of the Electrochemical Society, vol. 144, no. 6, pp. L173–L175, 1997.
View at: Google Scholar
W. S. Huang, B. D. Humphrey, and A. G. MacDiarmid, “Polyaniline, a novel conducting polymer. Morphology and chemistry of its oxidation and reduction in aqueous electrolytes,” Journal of the Chemical Society, Faraday Transactions 1, vol. 82, no. 8, pp. 2385–2400, 1986.
View at: Publisher Site | Google Scholar
W. W. Focke, G. E. Wnek, and Y. Wei, “Influence of oxidation state, pH, and counterion on the conductivity of polyaniline,” Journal of Physical Chemistry, vol. 91, no. 22, pp. 5813–5818, 1987.
View at: Google Scholar
A. Gruger, A. Novak, A. Régis, and Ph. Colomban, “Infrared and Raman study of polyaniline part II: influence of ortho substituents on hydrogen bonding and UV/Vis-near-IR electron charge transfer,” Journal of Molecular Structure, vol. 328, no. C, pp. 153–167, 1994.
View at: Google Scholar
A. U. H. A. Shah and R. Holze, “In situ UV-vis spectroelectrochemical studies of the copolymerization of o-aminophenol and aniline,” Synthetic Metals, vol. 156, no. 7-8, pp. 566–575, 2006.
View at: Publisher Site | Google Scholar
C. Chen, C. Sun, and Y. Gao, “Electrosynthesis of poly(aniline-co-p-aminophenol) having electrochemical properties in a wide pH range,” Electrochimica Acta, vol. 53, no. 7, pp. 3021–3028, 2008.
View at: Publisher Site | Google Scholar
L. Zhang and J. Lian, “Electrochemical synthesis of copolymer of aniline and o-aminophenol and its use to the electrocatalytic oxidation of ascorbic acid,” Journal of Electroanalytical Chemistry, vol. 611, no. 1-2, pp. 51–59, 2007.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2011 Lucia H. Mascaro et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3561

Downloads

2551

Citations