Potentiometric Multisensory Systems with Novel Ion-Exchange Polymer-Based Sensors for Analysis of Drugs

Bobreshova, Olga V.; Parshina, Anna V.; Polumestnaya, Ksenia A.

doi:https://doi.org/10.1155/2012/392735

International Journal of Electrochemistry

On this page

Abstract Introduction Experimental Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Special Issue

Ionic Liquids: Potential Electrolytes for Electrochemical Applications

View this Special Issue

Research Article | Open Access

Volume 2012 | Article ID 392735 | https://doi.org/10.1155/2012/392735

Potentiometric Multisensory Systems with Novel Ion-Exchange Polymer-Based Sensors for Analysis of Drugs

Olga V. Bobreshova,¹Anna V. Parshina,¹and Ksenia A. Polumestnaya¹

Academic Editor: Karl Scott Ryder

Received20 Jun 2011

Accepted07 Sept 2011

Published22 Nov 2011

Abstract

This paper examines potentiometric multisensory systems that consist of novel cross-sensitive PD-sensors (Potential Donnan-sensors). The analytical signal of PD-sensors is the Donnan potential at the ion-exchange polymer/electrolyte test solution interface. The use of novel sensors for the quantitative analysis of multicomponent aqueous solutions of amino acids, vitamins and medical substances is based on protolytic and ion-exchange reactions at the interfaces of ion-exchangers and test solutions. The potentiometric sensor arrays consist of PD-sensors and ion-selective electrodes. Such systems were developed for the multicomponent quantitative analysis of lysine monohydrochloride, thiamine chloride and novocaine hydrochloride solutions that contained salts of alkaline and alkaline-earth metals, as well as for mixed solutions of nicotinic acid and pyridoxine hydrochloride. Multivariate methods of analysis were used for sensor calibration and the analysis of the total response of sensor arrays. The errors of measurement of the electrolytes in aqueous solutions did not exceed 10%. The developed multisensory systems were used to determine the composition of a therapeutic “Mineral salt with low content of sodium chloride” and to determine concentrations of novocaine in sewage samples from a dental clinic.

1. Introduction

UV spectrophotometry [1], spectrofluorimetry [2], and HPLC [3] are commonly used methods for the quantitative analysis of amino acids, vitamins, and medical substances in aqueous solutions.

The advantages of potentiometric methods include the possibility of rapid, in situ analysis, the automation and separation of measurements, the simplicity of the technique, and the absence of any probe preparation [4–6]. The direct potentiometric determination of ions in aqueous solutions is based on either the measurement of membrane potential or oxidation-reduction potential of ion-selective electrodes (ISEs). Classical representations of ISEs are based on the theory of a glass electrode [7–10]. The Nicolsky-Eisenman equation can be applied to the description of a sensor response in multicomponent solutions. The influences of interfering ions are considered by means of selectivity constants, which are strictly reasonable only for binary systems. The use of ISEs in real systems is currently limited by their low selectivity and accuracy in multicomponent systems.

Modern investigations in the field of potentiometric sensors have taken the following approaches: the search for novel materials useful for the construction of ISEs [11–13], the miniaturisation of sensors [14, 15], the elimination of a transmembranous stream of defined ions from an ISE internal reference solution in test solutions [16, 17], the development of a theory describing ISEs without restrictions concerning equilibrium or steady state [6, 18] and research and development of multisensitive systems for the analysis of multicomponent liquid environments [19–25].

A multisensitive system includes an array of cross-sensitive sensors (i.e., sensors that are sensitive to several components in a given solution) and algorithms for processing the multidimensional data from a sensor array [19–26]. References [21–25] offer criteria for an estimation of cross-sensitivity, including the average inclination (i.e., sensitivity factor), the stability factor, and the nonselectivity factor. The sensitivity factor is the average value of lean angles from calibrations of all sensors in an array in individual solutions of defined components. The stability factor is the average value of a lean angle relative to the distribution of lean angles from calibrations of all sensors in individual solutions of defined components. The nonselectivity factor is the average inclination relative to a distribution of the average inclinations. The response of an array of cross-sensitive sensors is difficult because it contains information from various components that are present in the test solution, in addition to their interactions. Multivariate calibrations reduce the uncertainty of the analysis and reveal internal hidden interactions between variables as a result of increasing concentrations [27]. Established potentiometric multisensitive systems, such as the “electronic tongue,” only permit qualitative and semiquantitative analyses of foodstuffs and pharmaceutical products [19–26].

Recently, we described the development of a novel potentiometric sensor (PD sensor), which measures the Donnan potential at an ion-exchange polymer (IEP)/electrolyte test solution interface [28–33]. The Donnan potential is the Galvani potential between two points outside the external interfaces of double electrical layers (DELs) at the IEP/test solution interface [34–37]. Consequently, it is impossible to directly measure the Donnan potential; however, it is possible to estimate its value. An attempt to define the Donnan potential is known. For this purpose, the electromotive force (EMF) of the electrochemical circuit is measured, which includes two reference cells with reference electrodes, two reference solutions, and two salt bridges. One salt bridge is in contact with a test solution of the inorganic salt, and the second is in contact with a membrane surface. Additionally, the membrane is also in contact with a test solution [38]. One disadvantage of this method includes the short time of potential stability (1.5–2.0 min) due to transmembranous transport. Similarly, we determine the Donnan potential by measuring the EMF of the electrochemical circuit, but it is measured from the potential jump at the individual ion-exchanger/test solution interface [28–31]. The use of the membrane potential equilibrium constant as an analytical signal, which is the Donnan potential at the IEP/test solution interface, allows us to eliminate issues related to migration and diffusion in ionophore-based potentiometric sensors [16, 17]. This process ultimately increases the accuracy, stability and sensitivity of organic and inorganic ion measurements.

We have previously described the application of the PD sensor for the selective determination of lysine in the presence of neutral amino acids, ammonium ions [28, 32], and PD sensors, which are cross-sensitive in multicomponent solutions of some amino acids, vitamins, medicinal substances, and inorganic salts [29, 30, 33].

The aim of this paper was to develop potentiometric multisensory systems with novel polymer-based ion-exchange PD sensors for the determination of inorganic ions and various ionic forms of organic electrolytes in multicomponent aqueous solutions. Specifically, the analytes of interest were amino acids, vitamins, and medical substances.

2. Experimental

2.1. Reagents

All chemicals were of analytical reagent grade. All solutions were prepared using distilled water with a resistance of 0.35 MΩ·cm. The following analytes of interest were dissolved in aqueous solutions: lysine monohydrochloride (LysHCl), thiamine chloride (ThiaminCl), pyridoxine hydrochloride (PyridoxinHCl), nicotinic acid (Niacin), novocaine chloride (NovHCl), and inorganic electrolytes (NaCl, KCl, CaCl₂, and MgSO₄). Concentrations of the various solution components ranged from to 1.0 M. The pH values of LysHCl + KCl + NaCl + MgSO₄, ThiaminCl + KCl + NaCl, NovHCl + KCl + NaCl, and PyridoxinHCl + Niacin solutions were , (3.46–4.65) ± 0.04, .4, and (3.12–4.40) ± 0.05, respectively.

Systems containing sulphocation-exchange polymers with different structures (i.e., homogeneous perfluorinated sulphocation-exchange MF-4SK membranes and tubes, which are Russian analogues of Nafionc, and heterogeneous hydrocarbonic MC-40 membranes) and individual solutions of inorganic electrolytes (i.e., HCl, NaCl, and KCl) were previously researched for the selection of ion-exchange materials.

The structure of perfluorinated sulphocation-exchange polymers (PSPs) is formed from a system of nanopipes (10–17/5–10/3–5 nm) and pores (0.75–1.25 nm) with hydrophobic walls and hydrophilic sulphonate ionic groups within the channel volumes. The structural units of the hydrocarbonic polymers are represented by macroclusters of micropores with radii of 2-3 nm. The structural units of the hydrocarbonic polymers include ion-exchange groups and hydrophilic regions in a matrix that is divided by meso- and macropores with 5 ÷ 500 nm radii. The meso- and macropores are filled with test solution and include polymeric chains and an inert material [39].

PSPs are characterised by optimal selective properties as a result of fewer numbers of mesopores and the complete absence of macropores. Thus, the presence of hydrophobic (i.e., polytetrafluoroethylene chains) and hydrophilic (i.e., sulphonate ionic groups) regions in such polymers provides the matrix with labile structural components, which allows for the electrochemical properties of PSPs to be controlled by changing the ionic form of the polymers. Therefore, the hydrophobicity of the matrix from PSP and the absence of macropores together define a greater interface transition activation energy of hydrated ions compared to heterogeneous hydrocarbonic polymers. Hence, the use of PSPs in PD sensors provides increased signal, sensitivity, and accuracy in comparison with hydrocarbonic polymers. The comparison of the sensitivity of PSP-based PD sensors and MK-40 membranes for a number of inorganic ions is shown in Figure 1.

2.2. Apparatus

All solutions were analysed at °C using a liquid thermostat TJ-TS-01/12. All potentiometric measurements were performed using an Expert-001-3(0.1) fluid analyser. The reported relative error for this device for pH and EMF measurements is and , respectively. A potassium-selective electrode (K-SE, ELIS-121 K), calcium-selective electrode (Mg(Ca)-SE, ELIS-121Mg(Ca)) with a polyvinylchloride membrane, glass sodium-selective electrode (Na-SE, ELIS-112Na), silver chloride/silver reference electrode (EVS-1M3.1), and glass electrode (ELS-43-07) were all used for the pH control of test solutions. The sensors were rinsed with distilled water for 30 s between measurements.

2.3. Organisation Principles of Potentiometric Multisensory Systems with PD Sensors

A scheme of an electrochemical cell for analysing multicomponent aqueous solutions of organic and inorganic electrolytes [29–31] is presented in Figure 2.

The sensor array included PD sensors (), ISE (), and a silver chloride/silver reference electrode (C). The potentials of sensors and were measured with reference electrode C using a high-resistance electronic voltmeter V. Responses from electrode registered after 5–7 min, which was the time it took to reach a quasiequilibrium state [29–31].

The PD sensor [28] included two plastic encasements, designated 1 and 2, with volumes of 5 and 0.5 cm³, respectively. Encasements 1 and 2 were connected to a rubber stopper 3. Encasement 1 was filled with reference solution. Depending on the ionic form of the polymer, 1 mol/l solutions of HCl or KCl were used as reference solutions. Encasement 2 prevented the IEP from drying. The internal reference electrode 4, which was a silver wire covered with AgCl, was fixed in encasement 1 and immersed in a 1 M KCl solution. The free end of the 6–8 cm long PSP (both tube and membrane) 5 was fixed in stoppers 3 and 6 and was immersed in the test solution.

The electrochemical circuit (1) for the determination of the response of the PD sensor was constructed in the following configuration [29–31]: where and are the standard potentials of an intrinsic reference electrode of the PD sensor (A) and reference electrode (C), respectively; is the potential difference at the interface between the intrinsic reference solution of the PD sensor (A) and PSP; is the diffusion potential in the PSP phase; is the Donnan potential at the interface PSP/test solution; is the potential difference at the test solution/KCl saturated solution interface of the reference electrode (C).

The organisation of the PD sensor is as follows. The sum of all potential jumps in the EMF (1) was negligibly small compared to the Donnan potential at the PSP/test solution interface. The concentration of the reference solution was comparable to the concentration of fixed groups in PSP. The interfaces of the PSP/test solution and PSP/reference solution in the PD sensor were separated, which allowed us to neglect the influence of diffusion and migration processes on the analytical signal. Thus, the analytical signal of the PD sensor was the Donnan potential at the PSP/test solution interface. The quantitative consideration of the contributions of potential jumps at all interfaces to the total EMF for determination of the response of the PD sensor was presented previously [30].

2.4. Multivariate Calibration Methods

The stability, sensitivity, and selectivity of sensors were estimated in individual solutions of analytes. The determination of activity coefficients in the polyionic systems is a difficult scientific problem. Therefore, calibration of the sensors was performed in the coordinates. In this case, information about the relationship between activity and ion concentration in the phase of a solution and in the phase of the PSP was contained in the calibration coefficients.

Multivariate calibration methods were used to deduce the calibration equations for the calculation of analyte concentrations in mixed test solutions. The values of factors of concentrations were changed with a constant step. Initial factors were encrypted so that the sum of the values of any two factors from all experiments was equal to zero, which satisfied the requirements of nondegeneracy and orthogonality for the experimental plan. The absence of systematic errors and insignificant distinction of variances was a necessary requirement for the responses of sensors. Statistical models that did not take into account (3) and that did take into account (4), the interference of different components, were utilised to calculate concentrations of components and were as follows: where is the response of -sensor, mV; , and are coefficients of calibration equations, ; and are the negative decimal logarithm of concentrations of investigated -components.

The coefficients of multivariate calibration equations were determined by the method of least squares [27]. The values of the calibration coefficients were compared to the fitting errors to verify their statistical significance. To verify the adequacy of the calibration equations, the difference between the calculated and experimental response values of the sensors was compared to the distribution results from the duplicated experiments. A spreadsheet was used to calculate regression parameters for the sensor calibration curves.

3. Results and Discussion

The PD sensors were organised so that quasi-equilibria, which are formed at PSP/test solution and PSP/reference solution interfaces, are stable as a function of time and are independent from each other. The ionic properties and concentrations in the solution phase volumes and the ion-exchanger were slightly changed [34], permitting the use of PSP in the PD sensors, which were not transferred into the electrolyte test solution. Both inorganic ions of the initial form of an ion-exchanger and various ionic forms of organic electrolytes take part in the formation of the Donnan potential at the IEP/test multicomponent solution interface.

In systems with inorganic electrolytes, ion-exchange reactions are potentially defining. In such reactions, a hydrated shell of ions partially breaks up in solution phase and then reorganises in the PSP phase. Therefore, the sensitivity of the PD sensor to solution phase inorganic ion concentrations increases with decreasing charge, crystallographic radius, and increase in degree of hydration (Figure 1).

Various functional groups (–NH₂, –COOH) are present in the structure of amino acids, vitamins, and medical substances. These functional groups are capable of participating in ion-exchange and proteolytic reactions in the solution phase, PSP, and at the interface. The quasi-equilibria at the PSP/multicomponent test solution interface for K⁺- and H⁺-type PSPs are shown in Figures 3(a) and 3(b), respectively.

(a)

(b)

The potential defining reactions of PSP-based K⁺-type PD sensors are ion-exchange reactions. The PSP-based K⁺-type PD sensor was characterised by high sensitivity to all organic ( mV/pLysH, mV/pThiaminH, mV/pNovH, and mV/pPyridoxinH) and inorganic ( mV/pNa, mV/pK, and mV/pMg) ions (Figure 4). Thus, these ion-exchange reactions were the cause of cross-sensitivity of PD sensors in the multicomponent test solutions, in addition to solutions of ThiaminCl and NovHCl (i.e., the sorption of Thiamin⁺ and NovH⁺ ions was difficult because of their size). The PSP-based K⁺-type PD sensor was characterised by a higher sensitivity in solutions of the strong electrolytes LysHCl, ThiaminCl, PyridoxinHCl, NovHCl, KCl, NaCl, and MgSO₄ compared to the sensitivity of Niacin ( mV/pC), which is a weak electrolyte (Figure 4).

In PSP-based H⁺-type PD sensors, hydronium ions contributed to the Donnan potential. The hydronium ions competed with large organic cations during formation of the Donnan potential at the PSP/test solution interface because organic cations have hydrophilic and hydrophobic groups. Additionally, the singly charged organic cations LysH⁺, ThiaminH⁺, and NovH⁺ did not participate in ion-exchange reactions. These cations transformed into doubly-charged ions in the polymer phase as a result of a heterogeneous proteolytic reaction. Thus, adsorption at the interface of large doubly charged ions resulted in the decreased contribution of an organic component to the Donnan potential. As a result, the stability of the analytical signal of the PD sensor in such systems decreased. In some cases, the sensitivity to an organic component also decreased (e.g., by 1.2- and 1.5-times to LysH⁺ and NovH⁺, resp.). However, the sensitivity of PSP-based H⁺-type PD sensors to inorganic ions changed only slightly in comparison with PSP in salt forms (Figure 4). The sensitivity of the PSP-based H⁺-type PD sensors to nicotinic acid increased by 1.5-times compared to PSP-based K⁺-type PD sensors (Figure 4). In the PSP-based H⁺-type PD sensors, both cations (NiacinH⁺) and zwitterions (Niacin^±) of nicotinic acid contributed to the Donnan potential. Proteolytic reactions were the cause of Niacin^± ion contributions, which resulted in the transfer of cations to the PSP phase.

Thus, the use of PSPs in various ionic forms led to different PD sensor sensitivities toward the same organic component. However, the sensitivity of PD sensors toward inorganic ions changed insignificantly. The various influences of ionic forms of PSPs on the sensitivity to vitamins PyridoxinHCl and Niacin permitted the use of PD sensors for their joint determination in mixed aqueous solutions.

3.1. Multisensory Systems for Determination of Amino Acids, Vitamins, and Medical Substances

The potentiometric multisensory systems were developed for a multicomponent quantitative analysis of lysine monohydrochloride, thiamine chloride, and novocaine hydrochloride solutions that also contained chlorides of potassium and sodium. Additionally, solutions of nicotinic acid and pyridoxine hydrochloride were also analysed.

The sensor array for the analysis of solutions LysHCl + KCl + NaCl, ThiaminCl + KCl + NaCl, and NovHCl + KCl + NaCl included the PSP-based K⁺-type PD sensor (A₁), K-SE (B₁), Na-SE (B₂), and silver chloride/silver reference electrode (C). The electrochemical circuits for the determination of the responses of the sensor array are described by

The sensor array for the analysis of solutions LysHCl + KCl + NaCl + MgSO₄ included Mg(Ca)-SE (B₃) and sensors A₁, B₁, B₂, and C. The electrochemical circuits for the determination of the response of the sensor array are described by (5)–(8):

According to reference [24], a cross-sensitive sensor must be characterised by a sensitivity factor mV/pC, a stability factor , and a nonselectivity factor . Shown in Table 1 are the values of the factors , , and to ions LysH⁺, K⁺, Na⁺, Mg²⁺; Thiamin⁺, K⁺, and Na⁺, and NovH⁺, K⁺, and Na⁺ for sensors A₁ and B_k, respectively. The values of factors , , and were calculated on the basis of experimental data (Figure 4) that were obtained by sensor calibrations in test solutions ((mV/pC) = individual angle coefficient, (mV/pC)² = dispersion of individual angle coefficient, and (mV/pC)² = dispersion of average angle).

Large sensitivity and nonselectivity factors for the PSP-based K⁺-type PD sensor in the groups of ions (Table 1) predicted commensurable contributions of corresponding ions to the PD sensor response in LysHCl + KCl + NaCl, ThiaminCl + KCl + NaCl and NovHCl + KCl + NaCl solutions.

ISEs were not as highly selective in test solutions. For example, Mg(Ca)-SE had an average angle lower than 25 mV/pC (Table 1). The preferential sensitivity of ISEs to corresponding inorganic ions caused low nonselectivity factors. However, the main requirement for ISE selection is response stability (>2) toward defined components when cross-sensitive PD sensors are present in a sensor array.

The sensor array for the analysis of PyridoxinHCl + Niacin solutions included two PSP-based K⁺-(A₁) and H⁺-type (A₂) PD sensors and a reference electrode (C). The electrochemical circuit for the determination of PD sensor responses is described by (5) and (9)

Shown in Table 1 are the values of the cross-sensitivity criteria for PD sensors in individual solutions of PyridoxinHCl and Niacin. Significant values of factors , , and permitted the use of PSP-based K⁺- and H⁺-type PD sensors for the determination of PyridoxinHCl and Niacin in their mixed aqueous solutions. Thus, the various sensitivities of the sensors to defined components (Figure 4) predicted a significant distinction of their contributions to sensor responses in the mixed solutions.

The mixed test solutions LysHCl + KCl + NaCl, ThiaminCl + KCl + NaCl, NovHCl + KCl + NaCl, and PyridoxinHCl + Niacin were studied for the multivariate calibration of the sensor array. All possible combinations of factors pC were examined for each analyte in the range of 2–4 with a constant step of pC = 1. The coefficient estimates from the multivariate calibration equations without taking into account any interference of components to the responses of sensors and are presented in Table 2.

The coefficient estimates of the multivariate calibration equations, taking into account the interference of components on the responses of sensors and , are presented in Table 3.

The equations were adequate at a confidence level of 0.05. The statistical models that took into account the interactions of factors reduced the errors of PD sensors and the errors of Na-SE by 1.3–2.3-times and 1.4–3.2-times, respectively, compared to statistical models that did not take into account the interactions of factors. The errors for K-SE and Mg(Ca)-SE did not change. Therefore, to calculate analyte concentrations, we used (4) for the PD sensor and Na-SE and (3) for the K-SE and Mg(Ca)-SE.

Shown in Tables 4 and 5 are the actual and measured values of the analyte concentrations for some test solutions.

The number of replicate measurements was 6–8. The statistical data interpretation was made using a confidence coefficient of 0.95. The relative error of measurement was 2–10%.

3.2. Determination of Lysine Monohydrochlorides and Novocaine Hydrochlorides in Therapeutic Products and Sewage from a Dental Clinic

The potentiometric multisensory system used to analyse LysHCl + KCl + NaCl + MgSO₄ solutions was used for the analysis of therapeutic “mineral salt with low content of sodium chloride” samples. This product contained NaCl, KCl, MgSO₄, and LysHCl in the following mass rations (%): 0.35–0.58; 0.31–0.40; 0.05–0.10 and 0.02–0.10 [40]. The responses of sensors A₁, B₁, B₂, and B₃ were measured against a reference electrode C in aqueous solutions of 1 g/l of salt. The defined concentrations of LysH, K⁺, Na⁺, and Mg²⁺ were M ( LysHCl in dry sample), M ( KCl in dry sample), M ( NaCl in dry sample), and M ( MgSO₄ in dry sample), respectively. Thus, the measured composition of the therapeutic salt samples was in agreement with the stated product composition.

The potentiometric multisensory system used to analyse NovHCl + KCl + NaCl solutions was used to analyse sewage samples from a dental clinic. The responses of sensors A₁, B₁, and B₂ were measured against reference electrode C in sewage samples. These samples were taken from a sewer knee before and after a patient’s reception. The disparity of NovH⁺ concentrations in the dental clinic sewage before and after the patient’s reception was ()·10⁻⁵M. The concentrations of K⁺ and Na⁺ in the sewage were M and M, respectively, that is, in concordance with [41]. Regular drainage of novocaine hydrochloride into the sewage is a serious problem because the medications are toxic substances with narcotic activity.

4. Conclusion

Here, the development of potentiometric multisensory systems, in which novel potentiometric PD sensors were cross-sensitive was described. The analytical signal of PD sensors is the Donnan potential at the individual PSP/test electrolyte solution interface. The use of the membrane potential equilibrium component as an analytical signal, which is the Donnan potential at the IEP/test solution interface, resulted in the elimination of migration and diffusion problems inherent in potentiometric sensors. As a result, the accuracy and stability of the analysis subsequently increased. The use of novel sensors for the quantitative analysis of multicomponent aqueous solutions of amino acids, vitamins, and medical substances was based on proteolytic and ion-exchange reactions at the PSP/test solution interface. The potentiometric sensor arrays were developed for multicomponent quantitative analyses of lysine monohydrochloride, thiamine chloride, and novocaine hydrochloride solutions containing salts of alkaline and alkaline-earth metals as well as mixed solutions of nicotinic acid and pyridoxine hydrochloride. The sensor arrays consisted of cross-sensitive PD sensors and ISEs. The multivariate methods of the analysis were used for sensor calibrations in addition to the analysis of the total response of the sensor arrays. The relative errors of electrolyte measurements in aqueous solutions did not exceed 10%.

The developed multisensory systems were then used to determine the composition of therapeutic “mineral salt with low content of sodium chloride” and dental clinic sewage.

The PD sensor multisensory systems made it possible to perform quantitative analyses of multicomponent solutions of different electrolytes, which is in contrast to the majority of known potentiometric sensors arrays that only permit semiquantitative analyses.

Acknowledgments

The authors thank cand.ch.sc., the chief of the laboratory of Membrane Processes OSS “Plastpolymer” (St. Petersburg, Russia) Timofeev Sergey Vasilevich for giving samples of perfluorinated sulphonic cation-exchange membranes, tubes, and rods. This study was funded by the Russian Fund of Fundamental Research (09-03-97505 r_center_a).

References

D. Özdemir and E. Dinc, “Determination of thiamine HCl and pyridoxine HCl in pharmaceutical preparations using UV-Visible spectrophotometry and genetic algorithm based multivariate calibration methods,” Chemical and Pharmaceutical Bulletin, vol. 52, no. 7, pp. 810–817, 2004.
View at: Publisher Site | Google Scholar
F. Feng, K. Wang, Z. Chen, Q. Chen, J. Lin, and S. Huang, “Flow injection renewable drops spectrofluorimetry for sequential determinations of Vitamins B1, B2 and B6,” Analytica Chimica Acta, vol. 527, no. 2, pp. 187–193, 2004.
View at: Publisher Site | Google Scholar
Z. Chen, B. Chen, and S. Yao, “High-performance liquid chromatography/electrospray ionization-mass spectrometry for simultaneous determination of taurine and 10 water-soluble vitamins in multivitamin tablets,” Analytica Chimica Acta, vol. 569, no. 1-2, pp. 169–175, 2006.
View at: Publisher Site | Google Scholar
A. Scholz, Ed., Electrochemical Methods: Guide to Experiments and Applications, Springer, Berlin, Germany, 2010.
P. Gründler, Chemical Sensors: An Introduction for Scientists and Engineers, Springer, Berlin, Germany, 2006.
J. Bobacka, A. Ivaska, and A. Lewenstam, “Potentiometric ion sensors,” Chemical Reviews, vol. 108, no. 2, pp. 329–351, 2008.
View at: Publisher Site | Google Scholar
B. P. Nikolsky, M. M. Shultz, A. A. Belijustin, and A. A. Lev, Glass Electrodes for Hydrogen and Other Cations, E-Publishing, New York, NY, USA, 1967, Edited by G. Eisenman.
Z. Boksay and B. Lengyuel, “Vacancy type mechanism of the electrical relaxation processes in glass,” Journal of Non-Crystalline Solids, vol. 14, no. 1, pp. 79–87, 1974.
View at: Publisher Site | Google Scholar
G. Eisenman, D. O. Rudin, and J. U. Casby, “Glass electrode for measuring sodium ion,” Science, vol. 126, no. 3278, pp. 831–834, 1957.
View at: Google Scholar
A. A. Belyustin, “The centenary of glass electrode: from Max Cremer to F. G. K. Baucke,” Journal of Solid State Electrochemistry, vol. 15, no. 1, pp. 47–65, 2011.
View at: Publisher Site | Google Scholar
R. -Q. Yu, Z. -R. Zhang, and G. -L. Shen, “Potentiometric sensors: aspects of the recent development,” Sensors and Actuators B, vol. 65, no. 1, pp. 150–153, 2000.
View at: Publisher Site | Google Scholar
A. R. Pires, A. N. Araújo, M. C. B. S. M. Montenegro, P. Chocholous, and P. Solich, “New ionophores for vitamin B1 and vitamin B6 potentiometric sensors for multivitaminic control,” Journal of Pharmaceutical and Biomedical Analysis, vol. 46, no. 4, pp. 683–691, 2008.
View at: Publisher Site | Google Scholar
E. Bakker and M. E. Meyerhoff, “Ionophore-based membrane electrodes: new analytical concepts and non-classical response mechanisms,” Analytica Chimica Acta, vol. 416, no. 2, pp. 121–137, 2000.
View at: Publisher Site | Google Scholar
P. Ciosek, R. Mamińska, A. Dybko, and W. Wróblewski, “Potentiometric electronic tongue based on integrated array of microelectrodes,” Sensors and Actuators B, vol. 127, no. 1, pp. 8–14, 2007.
View at: Publisher Site | Google Scholar
E. Bakker and E. Pretsch, “Nanoscale potentiometry,” Trends in Analytical Chemistry, vol. 27, no. 7, pp. 612–618, 2008.
View at: Publisher Site | Google Scholar
E. Bakker, “Determination of unbiased selectivity coefficients of neutral carrier-based cation-selective electrodes,” Analytical Chemistry, vol. 69, no. 6, pp. 1061–1069, 1997.
View at: Google Scholar
A. Ceresa, A. Radu, S. Peper, E. Bakker, and E. Pretsch, “Rational design of potentiometric trace level ion sensors. A Ag+-selective electrode with a 100 ppt detection limit,” Analytical Chemistry, vol. 74, no. 16, pp. 4027–4036, 2002.
View at: Publisher Site | Google Scholar
J. Janata and M. Josowicz, “Nernstian and non-nernstian potentiometry,” Solid State Ionics, vol. 94, no. 1-4, pp. 209–215, 1997.
View at: Google Scholar
A. Mimendia, J. M. Gutiérrez, L. Leija et al., “A review of the use of the potentiometric electronic tongue in the monitoring of environmental systems,” Environmental Modelling and Software, vol. 25, no. 9, pp. 1023–1030, 2010.
View at: Publisher Site | Google Scholar
L. Escuder-Gilabert and M. Peris, “Review: highlights in recent applications of electronic tongues in food analysis,” Analytica Chimica Acta, vol. 665, no. 1, pp. 15–25, 2010.
View at: Publisher Site | Google Scholar
A. V. Legin, A. M. Rudnitskaya, Y. G. Vlasov, C. Di Natale, and A. D'Amico, “Features of the electronic tongue in comparison with the characteristics of the discrete ion-selective sensors,” Sensors and Actuators B, vol. 58, no. 1–3, pp. 464–468, 1999.
View at: Publisher Site | Google Scholar
A. V. Legin, E. A. Bychkov, and Y. G. Vlasov, “Analytical applications of chalcogenide glass chemical sensors in environmental monitoring and process control,” Sensors and Actuators B, vol. 24, no. 1–3, pp. 309–311, 1995.
View at: Google Scholar
A. V. Legin, E. A. Bychkov, and Y. G. Vlasov, “Analytical applications of chalcogenide glass chemical sensors in environmental monitoring and process control,” Sensors and Actuators B, vol. 24, no. 1–3, pp. 309–311, 1995.
View at: Google Scholar
A. Rudnitskaya, A. Ehlert, A. Legin, Y. Vlasov, and S. Büttgenbach, “Multisensor system on the basis of an array of non-specific chemical sensors and artificial neural networks for determination of inorganic pollutants in a model groundwater,” Talanta, vol. 55, no. 2, pp. 425–431, 2001.
View at: Publisher Site | Google Scholar
A. V. Legin, D. O. Kirsanov, V. A. Babain, A. V. Borovoy, and R. S. Herbst, “Cross-sensitive rare-earth metal sensors based on bidentate neutral organophosphorus compounds and chlorinated cobalt dicarbollide,” Analytica Chimica Acta, vol. 572, no. 2, pp. 243–247, 2006.
View at: Publisher Site | Google Scholar
N. Garsia-Villar, J. Saurina, and S. Hernandez-Cassou, “Potentiometric sensor array for the determination of lysine in feed samples using multivariate calibration methods,” Fresenius' Journal of Analytical Chemistry, vol. 371, pp. 1001–1008, 2001.
View at: Publisher Site | Google Scholar
B. K. Lavine and J. Workman, “Chemometrics,” Analytical Chemistry, vol. 74, no. 12, pp. 2763–2769, 2002.
View at: Publisher Site | Google Scholar
O. V. Bobreshova, M. V. Agupova, and A. V. Parshina, “Potentiometric determination of lysine in aqueous solutions using MF-4SK modified perfluorinated membranes,” Journal of Analytical Chemistry, vol. 64, no. 6, pp. 642–647, 2009.
View at: Publisher Site | Google Scholar
O. V. Bobreshova, A. V. Parshina, and E. A. Ryzhkova, “Determination of the ionic composition of perfluorinated sulfocationite membranes based on Donnan potential estimates,” Russian Journal of Electrochemistry, vol. 45, no. 11, pp. 1234–1239, 2009.
View at: Publisher Site | Google Scholar
O. V. Bobreshova, A. V. Parshina, M. V. Agupova, and K. A. Polumestnaya, “Determination of amino acids, vitamins, and drug substances in aqueous solutions using new potentiometric sensors with Donnan potential as analytical signal,” Russian Journal of Electrochemistry, vol. 46, no. 11, pp. 1252–1262, 2010.
View at: Publisher Site | Google Scholar
O. V. Bobreshova, A. V. Parshina, and K. A. Polumestnaya, “A new type of potentiometric sensors based on perfluorinated, sulfonated cation exchange membranes for quantitative analysis of multicomponent aqueous solutions,” Petroleum Chemistry, vol. 51, pp. 492–501, 2011.
View at: Google Scholar
O. V. Bobreshova, M. V. Agupova, A. V. Parshina, and S. V. Timofeev, RF patent no. 2376591, 2009, Byull. izobret., no. 35, 6 p, 2009.
O. V. Bobreshova, A. V. Parshina, S. V. Timofeev, and K. A. Polumestnaya, RF patent no. 87260, 2009, Byull. izobret., no. 27, 2 p, 2009.
F. G. Donnan, “Theory of membrane equilibria and membrane potentials in the presence of non-dialysing electrolytes. A contribution to physical-chemical physiology,” Journal of Membrane Science, vol. 100, no. 1, pp. 45–55, 1995.
View at: Publisher Site | Google Scholar
R. L. Gustafson, “Donnan Equilibria in Polystyrenesulfonate Gels,” The Journal of Physical Chemistry, vol. 70, pp. 957–961, 1966.
View at: Google Scholar
R. P. Back and P. Vanysek, “Interfacial potential differences at mixed conductor interfaces: Nernst, Nernst-Donnan, Nernst Distribution and generalization,” Journal of Electroanalytical Chemistry, vol. 292, pp. 73–91, 1990.
View at: Google Scholar
F. Helfferich, “Ionenaustauscher,” in Grundlagen Struktur-Herstellung-Theorie, vol. 1, Chemie, Weinheim, Germany, 1959.
View at: Google Scholar
M. Higa, A. Tanioka, and A. Kira, “A novel measurement method of Donnan potential at an interface between a charged membrane and mixed salt solution,” Journal of Membrane Science, vol. 140, no. 2, pp. 213–220, 1998.
View at: Publisher Site | Google Scholar
H. G. Haubold, T. Vad, H. Jungbluth, and P. Hiller, “Nano structure of NAFION: a SAXS study,” Electrochimica Acta, vol. 46, no. 10-11, pp. 1559–1563, 2001.
View at: Publisher Site | Google Scholar
O. V. Bobreshova, P. I. Kulintsov, L. A. Zagorodnykh, and V. I. Popov, RF patent no. 2286071, 2004, Byull. izobret., no. 30, 2 p., 2006.
E. Emmanuel, M. G. Pierre, and Y. Perrodin, “Groundwater contamination by microbiological and chemical substances released from hospital wastewater: health risk assessment for drinking water consumers,” Environment International, vol. 35, no. 4, pp. 718–726, 2009.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2012 Olga V. Bobreshova et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1451

Downloads

1123

Citations