Table of Contents
International Journal of Manufacturing Engineering
Volume 2014 (2014), Article ID 259129, 16 pages
http://dx.doi.org/10.1155/2014/259129
Research Article

Material Removal Rate, Electrode Wear Rate, and Surface Roughness Evaluation in Die Sinking EDM with Hollow Tool through Response Surface Methodology

Department of Mechanical Engineering, M. M. University, Mullana, Ambala, Haryana 133203, India

Received 15 May 2014; Accepted 25 August 2014; Published 23 September 2014

Academic Editor: Gilles Dessein

Copyright © 2014 Teepu Sultan et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. Rajesha, A. K. Sharma, and P. Kumar, “On electro discharge machining of inconel 718 with hollow tool,” Journal of Materials Engineering and Performance, vol. 21, no. 6, pp. 882–891, 2012. View at Publisher · View at Google Scholar · View at Scopus
  2. S. R. Nimbhorkar and B. D. Deshmukh, “Effect of case hardening treatment on the structure and properties of automobile gears,” International Journal of Pure and Applied Research in Engineering and Technology, vol. 1, no. 8, pp. 317–325, 2013. View at Google Scholar
  3. A. Bensely, S. Venkatesh, D. Mohan Lal, G. Nagarajan, A. Rajadurai, and J. Boland, “Determination of poisson's ratio of cryogenically treated case carburized steel (En 353) by using ultrasonic technique,” in Proceedings of the International Conference on Manufacturing Science and Technology, pp. 361–365, 2006.
  4. S. Murugesan and K. Balamurugan, “Optimization by Grey relational analysis of EDM parameters in machining Al-15% SiC MMC using multihole electrode,” Journal of Applied Sciences, vol. 12, no. 10, pp. 963–970, 2012. View at Publisher · View at Google Scholar · View at Scopus
  5. S. Singh and M. Verma, “A parametric optimization of electric discharge drill machine using taguchi approach,” Journal of Engineering, Computers & Applied Sciences, vol. 1, no. 3, pp. 39–48, 2012. View at Google Scholar
  6. F. L. Amorim and W. L. Weingaertner, “Die-sinking electrical discharge machining of a high-strength copper-based alloy for injection molds,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 26, no. 2, pp. 137–144, 2004. View at Google Scholar · View at Scopus
  7. O. Yilmaz, A. T. Bozdana, M. A. Okka, and I. H. Filiz, “A comparative investigation of the effects of single and multi-channel electrodes in EDM fast hole drilling of aerospace alloys,” in Proceedings of the 5th International Conference and Exhibition on Design and Production of Machines and Dies/Molds, Kusadasi, Turkey, June 2009.
  8. R. Manikandan and R. Venkatesan, “Optimizing the machining parameters of micro-EDM for Inconel 718,” Journal of Applied Sciences, vol. 12, no. 10, pp. 971–977, 2012. View at Publisher · View at Google Scholar · View at Scopus
  9. N. Sharma, R. Khanna, and R. D. Gupta, “Parametric optimization on WEDM for HSLA by integrated RSM and genetic algorithm,” in AEMDS, 2014.
  10. G. Kibria, B. R. Sarkar, B. B. Pradhan, and B. Bhattacharyya, “Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti-6Al-4V alloy,” International Journal of Advanced Manufacturing Technology, vol. 48, no. 5-8, pp. 557–570, 2010. View at Publisher · View at Google Scholar · View at Scopus
  11. M. S. Azad and A. B. Puri, “Simultaneous optimisation of multiple performance characteristics in micro-EDM drilling of titanium alloy,” International Journal of Advanced Manufacturing Technology, vol. 61, no. 9-12, pp. 1231–1239, 2012. View at Publisher · View at Google Scholar · View at Scopus
  12. A. D. Patel, M. C. Parekh, B. B. Patel, and B. B. Patel, “Multi-objective optimisation of die sinking electro discharge machining process using Taguchi,” International Journal of Engineering Research and Applications, vol. 2, no. 6, pp. 1367–1371, 2012. View at Google Scholar
  13. P. Janmanee and A. Muttamara, “Optimization of electrical discharge machining of composite 90WC-10Co base on taguchi approach,” European Journal of Scientific Research, vol. 64, no. 3, pp. 426–436, 2011. View at Google Scholar · View at Scopus
  14. M. Boujelbene, E. Bayraktar, W. Tebni, and S. Ben Salem, “Influence of machining parameters on the surface integrity in electrical discharge machining,” International Scientific Journal, vol. 37, no. 2, 2009. View at Google Scholar
  15. A. K. Khanra, S. Patra, and M. M. Godkhindi, “Electrical discharge machining studies on reactive sintered FeAl,” Bulletin of Materials Science, vol. 29, no. 3, pp. 277–280, 2006. View at Publisher · View at Google Scholar · View at Scopus
  16. H. K. Kansal, S. Singh, and P. Kumar, “Parametric optimization of powder mixed electrical discharge machining by response surface methodology,” Journal of Materials Processing Technology, vol. 169, no. 3, pp. 427–436, 2005. View at Publisher · View at Google Scholar · View at Scopus
  17. T. Y. Tai and S. J. Lu, “Improving the fatigue life of electro-discharge-machined SDK11 tool steel via the suppression of surface cracks,” International Journal of Fatigue, vol. 31, no. 3, pp. 433–438, 2009. View at Publisher · View at Google Scholar · View at Scopus
  18. A. Kumar, V. Kumar, and J. Kumar, “Investigation of machining parameters and surface integrity in wire electric discharge machining of pure titanium,” Proceedings of the Institution of Mechanical Engineers B: Journal of Engineering Manufacture, vol. 227, no. 7, pp. 972–992, 2013. View at Publisher · View at Google Scholar · View at Scopus
  19. A. T. Bozdana, O. Yilmaz, M. A. Okka, and İ. H. Filiz, “A comparative experimental study on fast hole EDM of Inconel 718 and Ti-6Al-4V,” in Proceedings of the 5th International Conference and Exhibition on Design and Production of MACHINES and DIES/MOLDS, 2009.
  20. U. Çaydaş and A. Hasçalik, “Modeling and analysis of electrode wear and white layer thickness in die-sinking EDM process through response surface methodology,” International Journal of Advanced Manufacturing Technology, vol. 38, no. 11-12, pp. 1148–1156, 2008. View at Publisher · View at Google Scholar · View at Scopus
  21. N. Sharma, R. Khanna, and R. Gupta, “Multi quality characteristics of WEDM process parameters with RSM,” Procedia Engineering, vol. 64, pp. 710–719, 2013. View at Publisher · View at Google Scholar
  22. N. Sharma, R. Khanna, R. D. Gupta, and R. Sharma, “Modeling and multiresponse optimization on WEDM for HSLA by RSM,” International Journal of Advanced Manufacturing Technology, vol. 67, no. 9-12, pp. 2269–2281, 2013. View at Publisher · View at Google Scholar · View at Scopus
  23. P. Gupta, R. Khanna, R. D. Gupta, and N. Sharma, “Effect of process parameters on kerf width in WEDM for HSLA using response surface methodology,” Journal of Engineering Technology, vol. 2, no. 1, pp. 1–5, 2012. View at Publisher · View at Google Scholar · View at Scopus
  24. A. Kumar, V. Kumar, and J. Kumar, “Multi-response optimization of process parameters based on response surface methodology for pure titanium using WEDM process,” International Journal of Advanced Manufacturing Technology, vol. 68, no. 9–12, pp. 2645–2668, 2013. View at Publisher · View at Google Scholar · View at Scopus
  25. D. C. Whittinghill, “A note on the robustness of Box-BEHnken designs to the unavailability of data,” Metrika, vol. 48, no. 1, pp. 49–52, 1998. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  26. K. Ojha, R. K. Garg, and K. K. Singh, “MRR improvement in sinking electrical discharge machining: a review,” Journal of Minerals & Materials Characterization & Engineering, vol. 9, no. 8, pp. 709–739, 2010. View at Google Scholar
  27. N. Kumar, L. Kumar, H. Tewatia, and R. Yadav, “Comparative study for MRR on die-sinking EDM using electrode of copper & graphite,” International Journal of Advanced Technology & Engineering Research, vol. 2, no. 2, pp. 170–174, 2012. View at Google Scholar
  28. A. Kumar, V. Kumar, and J. Kumar, “Investigation of microstructure and element migration for rough cut surface of pure titanium after WEDM,” International Journal of Microstructure and Materials Properties, vol. 8, no. 4-5, pp. 343–356, 2013. View at Publisher · View at Google Scholar · View at Scopus