Table of Contents
Retracted

This paper has been retracted as it contains figures that are substantially similar to figures in the following published papers: (1) “Microstructure and Mechanical Properties of A356/SiC Composites Fabricated by Electromagnetic Stir Casting” by Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2) “Effects of roller burnishing process parameters on surface roughness of A356/5%SiC composite using response surface methodology” by Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra.

View the full Retraction here.

References

  1. S. P. Dwivedi, S. Sharma, and R. K. Mishra, “Comparison of microstructure and mechanical properties of A356/SiC metal matrix composites produced by two different melting routes,” International Journal of Manufacturing Engineering, vol. 2014, Article ID 747865, 13 pages, 2014.
International Journal of Manufacturing Engineering
Volume 2014, Article ID 747865, 13 pages
http://dx.doi.org/10.1155/2014/747865
Research Article

Comparison of Microstructure and Mechanical Properties of A356/SiC Metal Matrix Composites Produced by Two Different Melting Routes

1Noida Institute of Engineering and Technology, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh 201310, India
2School of Engineering, Gautam Buddha University, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh 201310, India

Received 14 June 2014; Revised 1 October 2014; Accepted 2 October 2014; Published 21 October 2014

Academic Editor: Shia-Chung Chen

Copyright © 2014 Shashi Prakash Dwivedi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. E. J. Zoqui, M. Paes, and E. Es-Sadiqi, “Macro- and microstructure analysis of SSM A356 produced by electromagnetic stirring,” Journal of Materials Processing Technology, vol. 120, no. 1–3, pp. 365–373, 2002. View at Publisher · View at Google Scholar · View at Scopus
  2. T. P. D. Rajan, R. M. Pillai, B. C. Pai, K. G. Satyanarayana, and P. K. Rohatgi, “Fabrication and characterisation of Al-7Si-0.35Mg/fly ash metal matrix composites processed by different stir casting routes,” Composites Science and Technology, vol. 67, no. 15-16, pp. 3369–3377, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. D. Lu, Y. Jiang, G. Guan, R. Zhou, and Z. Li, “Refinement of primary Si in hypereutectic Al-Si alloy by electromagnetic stirring,” Journal of Materials Processing Technology, vol. 189, no. 1–3, pp. 13–18, 2007. View at Publisher · View at Google Scholar · View at Scopus
  4. C. G. Kang, J. W. Bae, and B. M. Kim, “The grain size control of A356 aluminum alloy by horizontal electromagnetic stirring for rheology forging,” Journal of Materials Processing Technology, vol. 187-188, pp. 344–348, 2007. View at Publisher · View at Google Scholar · View at Scopus
  5. A. Çetin and A. Kalkanli, “Effect of solidification rate on spatial distribution of SiC particles in A356 alloy composites,” Journal of Materials Processing Technology, vol. 205, no. 1–3, pp. 1–8, 2008. View at Publisher · View at Google Scholar · View at Scopus
  6. N. Barman, P. Kumar, and P. Dutta, “Studies on transport phenomena during solidification of an aluminum alloy in the presence of linear electromagnetic stirring,” Journal of Materials Processing Technology, vol. 209, no. 18-19, pp. 5912–5923, 2009. View at Publisher · View at Google Scholar · View at Scopus
  7. S. P. Dwivedi, S. Kumar, and A. Kumar, “Effect of turning parameters on surface roughness of A356/5% SiC composite produced by electromagnetic stir casting,” Journal of Mechanical Science and Technology, vol. 26, no. 12, pp. 3973–3979, 2012. View at Publisher · View at Google Scholar · View at Scopus
  8. D. Cree and M. Pugh, “Dry wear and friction properties of an A356/SiC foam interpenetrating phase composite,” Wear, vol. 272, no. 1, pp. 88–96, 2011. View at Publisher · View at Google Scholar · View at Scopus
  9. S. Gopalakrishnan and N. Murugan, “Production and wear characterisation of AA 6061 matrix titanium carbide particulate reinforced composite by enhanced stir casting method,” Composites B: Engineering, vol. 43, no. 2, pp. 302–308, 2012. View at Publisher · View at Google Scholar · View at Scopus
  10. Y. L. Yuan and Z. G. Li, “Microstructure and dry sliding wear behavior of Fe-based (Cr, Fe) 7C3 composite coating fabricated by PTA welding process,” Journal of Materials Engineering and Performance, vol. 22, no. 11, pp. 3439–3449, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. C. Mapelli, A. Gruttadauria, and M. Peroni, “Application of electromagnetic stirring for the homogenization of aluminium billet cast in a semi-continuous machine,” Journal of Materials Processing Technology, vol. 210, no. 2, pp. 306–314, 2010. View at Publisher · View at Google Scholar · View at Scopus
  12. J. Wang, P. Li, G. Mi, and Y. Zhong, “Microstructural evolution caused by electromagnetic stirring in superheated AlSi7Mg alloys,” Journal of Materials Processing Technology, vol. 210, no. 12, pp. 1652–1659, 2010. View at Publisher · View at Google Scholar · View at Scopus
  13. S. P. Dwivedi, S. Satpal, and M. Raghvendra, “A356 aluminum alloy and applications- a review,” Advanced Materials Manufacturing & Characterization, vol. 4, pp. 81–86, 2014. View at Google Scholar
  14. S. P. Dwivedi, “Effect of process parameters on tensile strength of friction stir welding A356/C355 aluminium alloys joint,” Journal of Mechanical Science and Technology, vol. 28, no. 1, pp. 285–291, 2014. View at Publisher · View at Google Scholar · View at Scopus
  15. S. P. Dwivedi, S. Sharma, and R. K. Mishra, “Effects of roller burnishing process parameters on surface roughness of A356/5%SiC composite using response surface methodology,” Advances in Manufacturing, 2014. View at Publisher · View at Google Scholar
  16. S. P. Dwivedi, S. Sharma, and R. K. Mishra, “Microstructure and mechanical behavior of A356/SiC/Fly-ash hybrid composites produced by electromagnetic stir casting,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2014. View at Publisher · View at Google Scholar