International Journal of Manufacturing Engineering

Table of Contents

Table of Contents: 2014

  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 786354
  • - Research Article

Finite Element Analysis of Residual Stress in Ti-6Al-4V Alloy Plate Induced by Deep Rolling Process under Complex Roller Path

J. J. Liou | T. I. El-Wardany
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 804705
  • - Research Article

Studies on the Process Parameters of Rapid Prototyping Technique (Stereolithography) for the Betterment of Part Quality

Raju Bangalore Singe Gowda | Chandra Sekhar Udayagiri | Drakshayani Doulat Narendra
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 921081
  • - Research Article

Experimental Investigation and Multiobjective Optimization of Turning Duplex Stainless Steels

Rastee D. Koyee | Uwe Heisel | ... | Rocco Eisseler
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 439634
  • - Research Article

Cutting Forces in Milling of Carbon Fibre Reinforced Plastics

Luca Sorrentino | Sandro Turchetta
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 769012
  • - Research Article

Flexural Strength Analysis of Starch Based Biodegradable Composite Using Areca Frond Fibre Reinforcement

Srinivas Shenoy Heckadka | Manjeshwar Vijaya Kini | ... | Ullal Achutha Kini
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 598531
  • - Research Article

Characterization and Optimization of Mechanical Properties of ABS Parts Manufactured by the Fused Deposition Modelling Process

Godfrey C. Onwubolu | Farzad Rayegani
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 385065
  • - Research Article

Failure Prediction in Bulk Metal Forming Process

Ameen Topa | Qasim H. Shah
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 154784
  • - Research Article

Resistance Spot Welding Optimization Based on Artificial Neural Network

Thongchai Arunchai | Kawin Sonthipermpoon | ... | Kreangsak Tamee
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 747865
  • - Research Article

Comparison of Microstructure and Mechanical Properties of A356/SiC Metal Matrix Composites Produced by Two Different Melting Routes

Shashi Prakash Dwivedi | Satpal Sharma | Raghvendra Kumar Mishra
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 291564
  • - Research Article

Modeling of Tool Wear in Vibration Assisted Nano Impact-Machining by Loose Abrasives

Sagil James | Murali M. Sundaram
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 259129
  • - Research Article

Material Removal Rate, Electrode Wear Rate, and Surface Roughness Evaluation in Die Sinking EDM with Hollow Tool through Response Surface Methodology

Teepu Sultan | Anish Kumar | Rahul Dev Gupta
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 175743
  • - Research Article

Finite Element Analysis of PMMA Stretch Blow Molding

Afef Bougharriou | Mohieddine Jeridi | ... | Kacem Saï
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 101823
  • - Research Article

Design and Fabrication of Diffractive Light-Collecting Microoptical Device with 1D and 2D Lamellar Grating Structures

ChaBum Lee
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 596128
  • - Research Article

Enhancing Multistage Deep-Drawing and Ironing Manufacturing Processes of Axisymmetric Components: Analysis and Experimentation

F. Javier Ramírez | Rosario Domingo | ... | Miguel A. Sebastian
  • International Journal of Manufacturing Engineering -
  • Special Issue
  • Volume 2014
  • - Article ID 261349
  • - Research Article

Analyzing the Effectiveness of Microlubrication Using a Vegetable Oil-Based Metal Working Fluid during End Milling AISI 1018 Steel

Vasim Shaikh | Nourredine Boubekri | Thomas W. Scharf

We are committed to sharing findings related to COVID-19 as quickly as possible. We will be providing unlimited waivers of publication charges for accepted research articles as well as case reports and case series related to COVID-19. Review articles are excluded from this waiver policy. Sign up here as a reviewer to help fast-track new submissions.