Table of Contents
Indian Journal of Materials Science
Volume 2014, Article ID 353698, 6 pages
http://dx.doi.org/10.1155/2014/353698
Research Article

Microstructure Properties of Rapidly Solidified Al-Zn-Mg-Cu Alloys

1Solid State Physics Department, National Research Center, Dokki, Giza 12311, Egypt
2Physics Department, Faculty of Science, Taif University, P.O. Box 888, Taif 21974, Saudi Arabia

Received 12 December 2013; Accepted 18 January 2014; Published 2 March 2014

Academic Editors: U. De, A. K. Meikap, and K. Sahoo

Copyright © 2014 Emad M. Ahmed. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Z. B. Sun, J. Guo, X. P. Song, Y. l. Zhu, and Y. Li, “Effects of Zr addition on the liquid phase separation and the microstructures of Cu–Cr ribbons with 18–22 at.% Cr,” Journal of Alloys and Compounds, vol. 455, no. 1-2, pp. 243–248, 2008. View at Publisher · View at Google Scholar · View at Scopus
  2. L. J. Huang, G. Y. Liang, Z. B. Sun, and Y. F. Zhou, “Nanocrystallization and hydriding properties of amorphous melt-spun Mg65Cu25Nd10 alloy,” Journal of Alloys and Compounds, vol. 432, no. 1-2, pp. 172–176, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. S. Yang, X. P. Song, X. S. Liu et al., “Magnetic properties enhancement of Nd2 Fe14B/α—Fe nanocomposites with a combined addition of Cu and Ti,” Journal of Applied Physics, vol. 93, no. 2, pp. 1199–1202, 2003. View at Google Scholar
  4. Y. Totik and M. Gavgali, “The effect of homogenization treatment on the hot workability between the surface and the center of AA 2014 ingots,” Materials Characterization, vol. 49, no. 3, pp. 261–268, 2002. View at Publisher · View at Google Scholar · View at Scopus
  5. B. Sarkar, M. Marek, and E. A. Starke, “The effect of copper content and heat treatment on the stress corrosion characteristics of Ai6Zn-2Mg-X Cu alloys,” Metallurgical Transactions A, vol. 12, no. 11, pp. 1939–1943, 1981. View at Publisher · View at Google Scholar
  6. A. Deschamps, Y. Drechet, and F. Livet, “Influence of copper addition on precipitation kinetics and hardening in Al–Zn–Mg alloy,” Materials Science and Technology, vol. 15, no. 9, pp. 993–1000, 1999. View at Publisher · View at Google Scholar
  7. S. C. Wang, M. J. Starink, and N. Gao, “Precipitation hardening in Al–Cu–Mg alloys revisited,” Scripta Materialia, vol. 54, no. 2, pp. 287–291, 2006. View at Publisher · View at Google Scholar · View at Scopus
  8. F. Y. Xie, X. Y. Yan, L. Ding et al., “A study of microstructure and microsegregation of aluminum 7050 alloy,” Materials Science and Engineering A, vol. 335, no. 1-2, pp. 144–153, 2003. View at Publisher · View at Google Scholar
  9. L. L. Rokhlin, T. V. Dobatkin, N. R. Bochvar, and E. V. Lysov, “Investigation of phase equilibria in alloys of the Al–Zn–Mg–Cu–Zr–Sc system,” Journal of Alloys and Compounds, vol. 367, no. 1-2, pp. 10–16, 2004. View at Publisher · View at Google Scholar
  10. X. M. Li and M. J. Starink, “Effect of compositional variations on characteristics of coarse intermetallic particles in overaged 7000 aluminium alloys,” Materials Science and Technology, vol. 17, no. 11, pp. 1324–1328, 2001. View at Publisher · View at Google Scholar
  11. H. Bedboudi, A. Bourbia, M. Draissiaa, S. Boulkhessaim, and M. Y. Debili, “Analysis of the solid solution microstructure of (HF) Al–Zn alloys,” Defect and Diffusion Forum, vol. 303-304, pp. 39–53, 2010. View at Publisher · View at Google Scholar · View at Scopus
  12. E. Ahmed, “Physical properties of Zn- 22 wt.% Al- x wt.% Ce melt spun eutectoid alloy,” Crystal Research & Technology, vol. 47, no. 6, pp. 689–695, 2012. View at Publisher · View at Google Scholar
  13. M. S. Mohammadi, A. Simchi, and C. Gierl, “Phase formation and microstructural evolution during sintering of Al–Zn–Mg–Cu alloys,” Powder Metallurgy, vol. 53, no. 1, pp. 62–70, 2010. View at Publisher · View at Google Scholar · View at Scopus
  14. W. Gao, D. Gifford, and Z.-Y. Liu, “Corrosion behaviour of zincalume and galvanised coatings in a sulphur-containing atmosphere,” Transactions of the Institution of Professional Engineers New Zealand, vol. 24, no. 1, 1997. View at Google Scholar
  15. R. J. Hill and C. L. Howard, “Quantitative phase analysis from neutron powder diffraction data using the rietveld method,” Journal of Applied Crystallography, vol. 20, pp. 467–474, 1987. View at Publisher · View at Google Scholar
  16. H. M. Rietveld, “Line profiles of neutron powder-diffraction peaks for structure refinement,” Acta Crystallographica, vol. 22, pp. 151–152, 1967. View at Publisher · View at Google Scholar
  17. H. M. Rietveld, “A profile refinement method for nuclear and magnetic structures,” Journal of Applied Crystallography, vol. 2, pp. 65–71, 1969. View at Publisher · View at Google Scholar
  18. R. A. Young and D. B. Wiles, “Profile shape functions in rietveld refinements,” Journal of Applied Crystallography, vol. 15, pp. 430–438, 1982. View at Publisher · View at Google Scholar
  19. R. A. Young, The Rietveld Method, edited by R. A. Young, Oxford University Press/IUCr, 1996.
  20. M. Bauccio, ASM Metals Reference Book, ASM International, 6th edition, 2001.
  21. B. Zlaticanin, B. Radonjic, and Z. Marinkovic, “DSC investigation of high-copper AlCuMg alloys,” in Materials and Technology, vol. 37, 2003. View at Google Scholar