Preparation of a Counter Electrode with <i>P</i>-Type NiO and Its Applications in Dye-Sensitized Solar Cell

Chou, Chuen-Shii; Hsiung, Chin-Min; Wang, Chun-Po; Yang, Ru-Yuan; Guo, Ming-Geng

doi:https://doi.org/10.1155/2010/902385

International Journal of Photoenergy

On this page

Abstract Introduction Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Special Issue

Thin-Film Photovoltaics

View this Special Issue

Research Article | Open Access

Volume 2010 | Article ID 902385 | https://doi.org/10.1155/2010/902385

Preparation of a Counter Electrode with P-Type NiO and Its Applications in Dye-Sensitized Solar Cell

Chuen-Shii Chou,^1,2Chin-Min Hsiung,^1,2Chun-Po Wang,²Ru-Yuan Yang,^1,3and Ming-Geng Guo²

Academic Editor: Stephen M. Goodnick

Received30 Nov 2009

Revised20 Mar 2010

Accepted10 May 2010

Published01 Jul 2010

Abstract

This study investigates the applicability of a counter electrode with a P-type semiconductor oxide (such as NiO) on a dye-sensitized solar cell (DSSC). The counter electrode is fabricated by depositing an NiO film on top of a Pt film, which has been deposited on a Fluorine-doped tin oxide (FTO) glass using an ion-sputtering coater (or E-beam evaporator), using a simple spin coating method. This study also examines the effect of the average thickness of film deposited on a working electrode upon the power conversion efficiency of a DSSC. This study shows that the power conversion efficiency of a DSSC with a Pt(E)/NiO counter electrode (4.28%) substantially exceeds that of a conventional DSSC with a Pt(E) counter electrode (3.16%) on which a Pt film was deposited using an E-beam evaporator. This result is attributed to the fact that the NiO film coated on the Pt(E) counter electrode improves the electrocatalytic activity of the counter electrode.

1. Introduction

Solar power is the most notable among renewable energy resources because of its low environmental impact and global availability. Among alternative forms of solar cells, dye-sensitized solar cells (DSSCs), as proposed by O’Regan and Grätzel [1], have attracted considerable interest since 1991 because of its properties, such as low production cost and low environmental impact during fabrication [2, 3].

In the past few years (2006–2009), several methods have been utilized in modifying the structure of a working electrode (TiO₂ electrode) to improve the performance of DSSCs [4–22]. Novel sensitizers were synthesized and applied in DSSCs to promote the absorption of the visible spectrum [3, 23–29]. Novel electrolytes were proposed to prevent leakage of the electrolyte or to increase the lifetime (or performance) of DSSCs [30–35]. Moreover, a quasisolid DSSC with straight ion paths based on an anodically oxidized Al₂O₃ film, which was full of nanopores from one side of the film to the other, was presented [36].

The counter electrode is an equally important component of the DSSC. The role of the counter electrode is to transfer electrons from an external circuit to the tri-iodide and iodine in the redox electrolyte. Currently, a layer of platinum (Pt) coated on a transparent conducting oxide (TCO) substrate is widely used as a counter electrode in DSSCs. Besides platinum (Pt), carbon materials (such as graphite powder and carbon black [37, 38], hard carbon spherule [39], single-walled carbon nanotubes [40], multiwalled carbon nanotubes [41], and nanosized carbon powder [42, 43]) have been used to prepare platinum-free counter electrodes.

Aside from the carbon materials, counter electrodes with metal oxide biphase materials (such as Pt/NiO [44, 45] and Pt/TiO₂ [45]) have been prepared using an RF magnetron cosputtering system. However, these highly efficient Pt/NiO (or Pt/TiO₂) bi-phase counter electrodes are obtained using an expensive vacuum technology which requires a sophisticated process control. Aside from this observation, Kay and Grätzel reported that a small amount of platinum might be dissolved in the electrolyte by oxidation and complex formation with iodide/tri-iodide (such as PtI₄ or H₂PtI₆) [37]. This may degrade the performance of counter electrodes after a certain period of exposure to light. Accordingly, decreasing the oxidation of Pt film in contact with the electrolyte is one of the most important factors in increasing the power conversion efficiency of DSSC; this is worthy of further study.

Therefore, in this study, a simple method (i.e., spin coating) was used to deposit a NiO film on top of a Pt film (Figure 1), which had been deposited on a FTO-glass (Fluorine-doped tin oxide, SnO₂:F) substrate using an E-beam evaporator (or ion-sputter coater) to protect the Pt film from oxidation and corrosion. The effect of P-type NiO on the electrocatalytic activity of the counter electrode and the power conversion efficiency of DSSC was investigated. A comparison of a DSSC with the proposed counter electrode with the conventional DSSC was also made in this study.

2. Experimental Details

The experiments involved (1) preparing the colloid of TiO₂ particles (P-25); (2) preparing the working electrode and measuring its properties; (3) preparing the colloid of P-type NiO; (4) preparing the counter electrode and measuring its properties; (4) assembling the DSSC by fitting the working electrode, the counter electrode, the electrolyte, and the copper conductive tape; (5) making J-V measurements of the DSSC.

2.1. Preparing and Measuring the Working Electrode

Fabricating a DSSC working electrode with a film of TiO₂ particles (Figure 1) followed these steps: (1) a colloid of TiO₂ particles (P-25) was prepared and homogenized; (2) using spin coating, the colloid of TiO₂ particles was deposited on top of a FTO-glass substrate, and it was then sintered at 500 C for 1 h in a high-temperature furnace (Thermolyne, 46100); (3) the FTO-glass substrate with the film of TiO₂ particles was immersed into a (3×10^-4 M) solution of N-719 dye (Ruthenium, RuL₂(NCS)₂) and ethyl alcohol (CH₃CH₂OH, 95%) at 70C for 6 h. The area of TiO₂ electrode of DSSC was 0.25 cm² in this study.

An α-step (Dekeak 6M) surface profiler was utilized to obtain the average thickness of the film on the FTO-glass substrate of the working electrode. In order to show the crystal structure of the TiO₂ powder, which was obtained by heating the solution of TiCl₄, its X-ray diffraction (XRD) patterns were measured using a powder X-ray diffractometer (Shimadzu, XRD-6000).

2.2. Preparing and Measuring the Counter Electrode

The procedure for fabricating a counter electrode of DSSC with a film of Pt sandwiched between a NiO film and a FTO-glass substrate (Figure 1) is as follows. (1) The P-type NiO was obtained by annealing the Ni powder in a high-temperature furnace at 500C; (2) the NiO colloid was prepared by mixing 1 g of NiO with solvents (20 ml of DI water, 1 ml of ethanol, 0.1 ml of acetylacetone, and 0.1 ml of Triton X-100) and then homogenized in an ultrasonic homogenizer for 30 min; (3) using spin coating, 2-3 ml of the NiO colloid was deposited on top of a Pt film, which had been deposited on the FTO-glass substrate using an E-beam evaporator (or ion-sputter coater); (4) this substrate was then sintered at 500C for 1 h in a high-temperature furnace.

In this study, in order to show the effect of the vacuum level on the performance of a DSSC, an E-beam evaporator (Kaoduen Tech. Corp.) with a vacuum level of Torr and an ion-sputter coater (Hitachi E-1010) with a vacuum level of Torr were used to deposit a Pt film on the FTO-glass substrate of the counter electrode. The area of a Pt film of counter electrode was 4.0 cm² in this study. Aside from this, the two-stage spin coating was used in this study: (1) in the first stage, the rotation speed of 1000 rpm and the duration of 5 s were used to remove the extra NiO colloid from the substrate; (2) in the second stage, the rotation speed of 1500 rpm and the duration of 15 s were used to homogenize the NiO film on the substrate.

The image and the micrograph of the counter electrode with a Pt film were obtained using a digital camera (Panasonic DMC-LZ2) and a scanning electron microscope (HITACHI S-4700), respectively. The reflectance and the cyclic voltammogram (CV) of the counter electrode were obtained using a UV-VIS-NIR spectrophotometer (Jasco V-600) and an electrochemical workstation (CH Instruments CHI-660C), respectively. Further, the surface roughness and the 3D micrograph of the counter electrode were obtained using a atomic force microscope (Digital Instrument NanoMan-NS4+D3100).

2.3. Assembling and Testing the DSSC

The working electrode, the counter electrode, and the copper conductive tape (Ted Pella) were fitted together, with the space between two electrodes adjusted to approximately 25 m for the liquid electrolyte. After sealing, the liquid electrolyte was injected into the cell through a prepared hole in the cell. The detailed preparation of the photoanode and the DSSC assembly were presented in [22].

A digital source meter (Keithley 2000) measured the open-circuit photovoltage and the short-circuit photocurrent of the DSSC, and a solar simulator (Science Tech. SS150) illuminated the DSSC. The power conversion efficiency of the DSSC is determined by where _oc, _sc, and _in represent the open-circuit photovoltage, the short-circuit photocurrent per unit area, and the incident light power (100 mW/cm²), respectively. Aside from this, fill factor (FF) is given by where and represent the voltage and the current per unit area at the maximum output power point, respectively.

3. Results and Discussion

3.1. Characteristics of TiCl₄ and NiO

Figure 2 shows the X-ray diffraction (XRD) patterns of dehydrated TiCl₄, as well as powders of Ni and NiO. The solid square, circle, and square in Figure 3 represent rutile, Ni, and NiO, respectively. From JCPDS 89-4920 (rutile), the XRD patterns of the dehydrated TiCl₄ show that three major peaks of rutile at , , and correspond to the diffraction from the 110, 101, and 211 planes, respectively. The purpose of immersing a FTO-glass substrate in the TiCl₄ solution before depositing the TiO₂ (P-25) colloid is to prevent the FTO-glass substrate from dye (or electrolyte) contamination, which might penetrate through the cavities of the TiO₂ (P-25) film. Ito et al. observed that TiCl₄ treatment induced improvements in the adhesion and mechanical strength of a nanocrystalline TiO₂ layer [22].

(a)

(b)

(a)

(b)

(c)

(d)

From JCPDS 89-5881 (nickel oxide), the XRD patterns of the NiO powder, obtained by annealing the Ni powder, show that three major peaks of NiO at , , and correspond to the diffraction from the 222, 400, and 440 planes, respectively. Instead of depositing and annealing Ni to form a NiO deposit on platinum, we have preferred to spin coat a previously formed NiO before sintering. This is because, compared with the Ni powder, NiO powder can be more easily dispersed in the solvent.

3.2. Characteristics of the Counter Electrode

This study used four kinds of counter electrode: (1) a counter electrode with a Pt film deposited on the FTO-glass substrate using an E-beam evaporator (called Pt(E)), (2) a counter electrode with a Pt film deposited on the FTO-glass substrate using an ion-sputter coater (called Pt(S)), (3) a counter electrode prepared by depositing a NiO film on top of Pt(E) (called Pt(E)/NiO), and (4) a counter electrode prepared by depositing a NiO film on top of Pt(S) (called Pt(S)/NiO).

Figure 3 shows the images and the SEM micrographs (20 kx) of the counter electrodes of Pt(E) and Pt(S). Figure 4 shows the variations in reflectance with light wavelength of the Pt(E), Pt(S),t(E)/NiO, and Pt(S)/NiO counter electrodes. For the counter electrodes used in this study, the reflectance increases with an increase in wavelength. For example, for the Pt(E) counter electrode, as the wavelength increases to 800 nm, its reflectance goes up to 50.4% (Figure 4). The light-reflecting character of the Pt film is desirable because it increases the light harvesting efficiency of the sensitizing dye [45, 46]. Aside from this, at a fixed wavelength, the reflectance of the Pt(E) counter electrode substantially exceeds that of the Pt(S) counter electrode. For example, at a fixed wavelength of 800 nm, the reflectance of the counter electrodes of Pt(E) and Pt(S) are 50.4% and 13.4%, respectively. This result is attributed to the fact that the vacuum level of the ion-sputter coater used in this study ( Torr) is not higher than that of the E-beam evaporator ( Torr), so the target (such as Pt) and the residual substance in the chamber are probably deposited on the substrate during sputtering. Therefore, unlike the Pt(E) counter electrode, the Pt(S) counter electrode is not able to mirror the digital camera, which was used to take images of the counter electrodes (Figure 3). At 800 nm wavelength, the reflectance of the Pt(E)/NiO counter electrode (26.6%) is close to that of the Pt(S)/NiO counter electrode (26.2%). Further, the sheet resistance of the Pt(S) counter electrode (9.73 ) also substantially exceeds that of the Pt(E) counter electrode (5.57 ).

Figure 5 shows the 3-D microstructures of the Pt(E), Pt(S), Pt(E)/NiO, and Pt(S)/NiO counter electrodes. The surface roughness average (Ra) of the Pt(E) counter electrode (14.213 nm) exceeds that of the Pt(S) counter electrode (12.894 nm), as shown in Figure 5. This is attributed to the fact that compared with evaporation, it is easier to maintain a stable deposition rate during sputtering, and it is also much easier to deposit a uniform film on a large area substrate [47]. Song and Lin observed that the hillock formation in a Pt/Ti film was obtained using UHV electron beam evaporation, but a rosette-type microstructure in the Pt/Ti film was obtained using DC-sputtering [48]. Aside from this, Zhou et al. indicated that the increased roughness improved the light scattering of the counter electrode [49].

(a)

(b)

(c)

(d)

Figure 6 shows the CVs of the Pt(E), Pt(S), Pt(E)/NiO, and Pt(S)/NiO counter electrodes. The oxidation and reduction peaks of I/I₃ on these counter electrodes are similar. For example, their oxidation potential ranges from 0.4 V to 0.9 V, and the reduction potential ranges from 0.0 V to 0.5 V (Figure 6). The presence of a NiO film enhances the current density during the redox process. For example, in the oxidation process, the highest current density of Pt(E)/NiO (7.2 mA/cm²) exceeds that of Pt(E) (6.1 mA/cm²). In the reduction process, the lowest current density of Pt(E)/NiO (5.2 mA/cm²) also exceeds that of Pt(E) (3.9 mA/cm²). This result is attributed to the fact that a larger active surface area due to a deposited NiO film corresponds to a more energetic electrocatalytic activity. A similar tendency was also observed by Kim et al. [45] and Yoon et al. [46].

(a)

(b)

3.3. Photoelectrochemical Behaviour

The - characteristics of DSSC in all tests are shown in Figure 7, and Table 1 presents the open-circuit photovoltage (), the short-circuit photocurrent per unit area (), the fill factor (FF), and the power conversion efficiency () of the DSSC in tests D1 to D8. In this study, the of the DSSC is kept at 0.65 V. The power conversion efficiency of DSSC with Pt(E) (or Pt(E)/NiO) exceeds 3%.

(a)

(b)

(c)

(d)

At a fixed counter electrode, as the average thickness of TiO₂ film increases, the power conversion efficiency increases. For example, for the Pt(E) counter electrode, the power conversion efficiency increases from 3.00% to 3.16% as the average thickness of the TiO₂ film increases from 12.0 m (in test D1) to 19.0 m (in test D2). The - curve of DSSC with a thicker TiO₂ film is above that of DSSC with a thinner TiO₂ film (Figure 7). This result is due to the following: (1) a TiO₂ film with a larger average thickness contains more TiO₂ (P-25) particles, which may absorb more ultraviolet light; (2) the working electrode with a thicker TiO₂ film corresponds to a higher adsorptive capability of the dye because more tiny cavities are created in this film on a FTO-glass substrate so that the larger number of electrons may be excited as the DSSC is exposed to the light.

Although the average thickness of the TiO₂ film in test D1 (12.0 m) is very close to that in test D3 (11.0 m), the power conversion efficiency of DSSC with a Pt(E) counter electrode in test D1 (3.00%) substantially exceeds that of DSSC with a Pt(S) counter electrode in test D3 (2.33%). This result may be due to the following:. (1) the Pt(S) counter electrode sheet resistance (9.73 ) significantly exceeds the Pt(E) counter electrode sheet resistance (5.57 ); (2) at a fixed wavelength, the Pt(E) counter electrode reflectance remarkably exceeds the Pt(S) counter electrode reflectance. Fang et al. showed that in order for a DSSC to have better power conversion efficiency, a counter electrode should have the following characteristics: (1) good conductivity for transferring electrons, (2) excellent catalytic activity for I/I₃ redox, and (3) light-reflecting ability to improve light-harvesting efficiency [50].

　　Most interestingly, the presence of a NiO film remarkably promotes the power conversion efficiency of DSSC. For example, the power conversion efficiencies of DSSC in tests D2 (with a Pt(E) counter electrode) and D6 (with a Pt(E)/NiO counter electrode) are 3.16% and 4.28%, respectively. Furthermore, the power conversion efficiencies of DSSC in tests D4 (with a Pt(S) counter electrode) and D8 (with a Pt(S)/NiO counter electrode) are 2.34% and 2.92%, respectively. These results are due to the following: (1) the NiO film deposited on top of Pt(E) (or Pt(S)) substantially enhances the surface roughness average (Ra) of the counter electrode (Table 1); (2) the increased roughness improves the light scattering as well as the electroactive area of a counter electrode. Kim et al. [45] showed that the overall conversion efficiency of DSSC increased to 3.62% and 4.21% through the use of Pt/NiO and Pt/TiO₂ bi-phase counter electrodes, respectively.

4. Conclusion

The effect of different kinds of counter electrodes on the power conversion efficiency of a DSSC was investigated. The power conversion efficiency of the DSSC with a Pt(E) counter electrode exceeds that of the DSSC with a Pt(S) counter electrode because the Pt(E) counter electrode has better reflectance. Furthermore, the power conversion efficiency of the DSSC with a Pt(E)/NiO counter electrode exceeds that of the DSSC with a Pt(E) counter electrode because the Pt(E)/NiO counter electrode has better electrocatalytic activity. Most importantly, this study supports the application of a NiO film deposited on the Pt-FTO substrate using a simple spin coating method to improve the performance of a DSSC. However, the optimal process for fabricating a DSSC with a NiO film on the counter electrode, which can promote the electrocatalytic activity of the counter electrode, must be implemented to yield a DSSC with a satisfactory power conversion efficiency.

Concerning the possible application of this nontransparent cathode that the NiO is deposited on top of the Pt film, it may decline the transparency of photovoltaic windows. However, besides photovoltaic windows, the other real applications of DSSC, such as DSSC lampshade, flower-shaped DSSC, and leaf-shaped DSSC, whose transparency may not be seriously considered, have received substantial attention, too. We believe that this counter electrode may facilitate the performance of aforementioned devices of DSSC.

Acknowledgments

The authors would like to thank the National Science Council, Taiwan for financially supporting this research under Contract nos. NSC 97-2221-E-020-035 and NSC 97-2918-I-020-001. The authors would also like to thank the National Pingtung University of Science and Technology, Taiwan for their financial support to establish the Research Center of Solar Photo-Electricity Applications.

References

B. O'Regan and M. Grätzel, “A low-cost, high-efficiency solar cell based on dye-sensitized colloidal ${TiO}_{2}$ films,” Nature, vol. 353, no. 6346, pp. 737–740, 1991.
View at: Google Scholar
N. S. Lewis, “Toward cost-effective solar energy use,” Science, vol. 315, no. 5813, pp. 798–801, 2007.
View at: Publisher Site | Google Scholar
S. Kim, D. Kim, H. Choi et al., “Enhanced photovoltaic performance and long-term stability of quasi-solid-state dye-sensitized solar cells via molecular engineering,” Chemical Communications, no. 40, pp. 4951–4953, 2008.
View at: Publisher Site | Google Scholar
M. Wei, Y. Konishi, H. Zhou, H. Sugihara, and H. Arakawa, “Utilization of titanate nanotubes as an electrode material in dye-sensitized solar cells,” Journal of the Electrochemical Society, vol. 153, no. 6, pp. A1232–A1236, 2006.
View at: Publisher Site | Google Scholar
G.-S. Kim, H.-K. Seo, V. P. Godble, Y.-S. Kim, O.-B. Yang, and H.-S. Shin, “Electrophoretic deposition of titanate nanotubes from commercial titania nanoparticles: application to dye-sensitized solar cells,” Electrochemistry Communications, vol. 8, no. 6, pp. 961–966, 2006.
View at: Publisher Site | Google Scholar
S.-J. Roh, R. S. Mane, S.-K. Min, W.-J. Lee, C. D. Lokhande, and S.-H. Han, “Achievement of 4.51% conversion efficiency using ZnO recombination barrier layer in ${TiO}_{2}$ based dye-sensitized solar cells,” Applied Physics Letters, vol. 89, no. 25, Article ID 253512, 2006.
View at: Publisher Site | Google Scholar
Y. H. Su, W. H. Lai, L. G. Teoh, M. H. Hon, and J. L. Huang, “Layer-by-layer Au nanoparticles as a Schottky barrier in a water-based dye-sensitized solar cell,” Applied Physics A, vol. 88, no. 1, pp. 173–178, 2007.
View at: Publisher Site | Google Scholar
J. Bandara and J. P. Yasomanee, “P-type oxide semiconductors as hole collectors in dye-sensitized solid-state solar cells,” Semiconductor Science and Technology, vol. 22, no. 2, pp. 20–24, 2007.
View at: Publisher Site | Google Scholar
S. Ito, T. N. Murakami, P. Comte et al., “Fabrication of thin film dye sensitized solar cells with solar to electric power conversion efficiency over 10%,” Thin Solid Films, vol. 516, no. 14, pp. 4613–4619, 2008.
View at: Publisher Site | Google Scholar
S. Sumikura, S. Mori, S. Shimizu, H. Usami, and E. Suzuki, “Syntheses of NiO nanoporous films using nonionic triblock co-polymer templates and their application to photo-cathodes of p-type dye-sensitized solar cells,” Journal of Photochemistry and Photobiology A, vol. 199, no. 1, pp. 1–7, 2008.
View at: Publisher Site | Google Scholar
S. Sumikura, S. Mori, S. Shimizu, H. Usami, and E. Suzuki, “Photoelectrochemical characteristics of cells with dyed and undyed nanoporous p-type semiconductor CuO electrodes,” Journal of Photochemistry and Photobiology A, vol. 194, no. 2-3, pp. 143–147, 2008.
View at: Publisher Site | Google Scholar
C.-S. Chou, R.-Y. Yang, M.-H. Weng, and C.-H. Yeh, “Study of the applicability of ${TiO}_{2}$ /dye composite particles for a dye-sensitized solar cell,” Advanced Powder Technology, vol. 19, no. 6, pp. 541–558, 2008.
View at: Publisher Site | Google Scholar
C.-S. Chou, R.-Y. Yang, M.-H. Weng, and C.-H. Yeh, “Preparation of ${TiO}_{2}$ /dye composite particles and their applications in dye-sensitized solar cell,” Powder Technology, vol. 187, no. 2, pp. 181–189, 2008.
View at: Publisher Site | Google Scholar
K.-M. Lee, C.-W. Hu, H.-W. Chen, and K.-C. Ho, “Incorporating carbon nanotube in a low-temperature fabrication process for dye-sensitized ${TiO}_{2}$ solar cells,” Solar Energy Materials and Solar Cells, vol. 92, no. 12, pp. 1628–1633, 2008.
View at: Publisher Site | Google Scholar
B. Yoo, K. Kim, S. H. Lee, W. M. Kim, and N.-G. Park, “ITO/ATO/ ${TiO}_{2}$ triple-layered transparent conducting substrates for dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 92, no. 8, pp. 873–877, 2008.
View at: Publisher Site | Google Scholar
B. N. Pawar, G. Cai, D. Ham et al., “Preparation of transparent and conducting boron-doped ZnO electrode for its application in dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 93, no. 4, pp. 524–527, 2009.
View at: Publisher Site | Google Scholar
K.-M. Lee, V. Suryanarayanan, and K.-C. Ho, “Influences of different ${TiO}_{2}$ morphologies and solvents on the photovoltaic performance of dye-sensitized solar cells,” Journal of Power Sources, vol. 188, no. 2, pp. 635–641, 2009.
View at: Publisher Site | Google Scholar
W. J. Lee, E. Ramasamy, and D. Y. Lee, “Effect of electrode geometry on the photovoltaic performance of dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 93, no. 8, pp. 1448–1451, 2009.
View at: Publisher Site | Google Scholar
U. O. Krašovec, M. Berginc, M. Hočevar, and M. Topič, “Unique ${TiO}_{2}$ paste for high efficiency dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 93, no. 3, pp. 379–381, 2009.
View at: Publisher Site | Google Scholar
T. Sawatsuk, A. Chindaduang, C. Sae-kung, S. Pratontep, and G. Tumcharern, “Dye-sensitized solar cells based on ${TiO}_{2}$ -MWCNTs composite electrodes: performance improvement and their mechanisms,” Diamond and Related Materials, vol. 18, no. 2-3, pp. 524–527, 2009.
View at: Publisher Site | Google Scholar
H. Wang, Y. Liu, H. Xu et al., “An investigation on the novel structure of dye-sensitized solar cell with integrated photoanode,” Renewable Energy, vol. 34, no. 6, pp. 1635–1638, 2009.
View at: Publisher Site | Google Scholar
C.-S. Chou, R.-Y. Yang, C.-K. Yeh, and Y.-J. Lin, “Preparation of ${TiO}_{2}$ /Nano-metal composite particles and their applications in dye-sensitized solar cells,” Powder Technology, vol. 194, no. 1-2, pp. 95–105, 2009.
View at: Publisher Site | Google Scholar
S. Hwang, J. H. Lee, C. Park et al., “A highly efficient organic sensitizer for dye-sensitized solar cells,” Chemical Communications, no. 46, pp. 4887–4889, 2007.
View at: Publisher Site | Google Scholar
J.-G. Chen, C.-Y. Chen, S.-J. Wu, J.-Y. Li, C.-G. Wu, and K.-C. Ho, “On the photophysical and electrochemical studies of dye-sensitized solar cells with the new dye CYC-B1,” Solar Energy Materials and Solar Cells, vol. 92, no. 12, pp. 1723–1727, 2008.
View at: Publisher Site | Google Scholar
S. Ito, H. Miura, S. Uchida et al., “High-conversion-efficiency organic dye-sensitized solar cells with a novel indoline dye,” Chemical Communications, no. 41, pp. 5194–5196, 2008.
View at: Publisher Site | Google Scholar
M. Xu, R. Li, N. Pootrakulchote et al., “Energy-level and molecular engineering of organic D-π-A sensitizers in dye-sensitized solar cells,” Journal of Physical Chemistry C, vol. 112, no. 49, pp. 19770–19776, 2008.
View at: Publisher Site | Google Scholar
C.-H. Yang, H.-L. Chen, Y.-Y. Chuang et al., “Characteristics of triphenylamine-based dyes with multiple acceptors in application of dye-sensitized solar cells,” Journal of Power Sources, vol. 188, no. 2, pp. 627–634, 2009.
View at: Publisher Site | Google Scholar
J. Pei, S. Peng, J. Shi et al., “Triphenylamine-based organic dye containing the diphenylvinyl and rhodanine-3-acetic acid moieties for efficient dye-sensitized solar cells,” Journal of Power Sources, vol. 187, no. 2, pp. 620–626, 2009.
View at: Publisher Site | Google Scholar
V. Kandavelu, H.-S. Huang, J.-L. Jian, T. C.-K. Yang, K.-L. Wang, and S.-T. Huang, “Novel iminocoumarin dyes as photosensitizers for dye-sensitized solar cell,” Solar Energy, vol. 83, no. 4, pp. 574–581, 2009.
View at: Publisher Site | Google Scholar
T. Kato, T. Kado, S. Tanaka, A. Okazaki, and S. Hayase, “Quasi-solid dye-sensitized solar cells containing nanoparticles modified with ionic liquid-type molecules,” Journal of the Electrochemical Society, vol. 153, no. 3, pp. A626–A630, 2006.
View at: Publisher Site | Google Scholar
T. C. Wei, C. C. Wan, and Y. Y. Wang, “Preparation and characterization of a micro-porous polymer electrolyte with cross-linking network structure for dye-sensitized solar cell,” Solar Energy Materials and Solar Cells, vol. 91, no. 20, pp. 1892–1897, 2007.
View at: Publisher Site | Google Scholar
S. Ganesan, B. Muthuraaman, V. Mathew, J. Madhavan, P. Maruthamuthu, and S. Austin Suthanthiraraj, “Performance of a new polymer electrolyte incorporated with diphenylamine in nanocrystalline dye-sensitized solar cell,” Solar Energy Materials and Solar Cells, vol. 92, no. 12, pp. 1718–1722, 2008.
View at: Publisher Site | Google Scholar
Y. Wang, Y. Sun, B. Song, and J. Xi, “Ionic liquid electrolytes based on 1-vinyl-3-alkylimidazolium iodides for dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 92, no. 6, pp. 660–666, 2008.
View at: Publisher Site | Google Scholar
D. Shi, N. Pootrakulchote, R. Li et al., “New efficiency records for stable dye-sensitized solar cells with low-volatility and ionic liquid electrolytes,” Journal of Physical Chemistry C, vol. 112, no. 44, pp. 17046–17050, 2008.
View at: Publisher Site | Google Scholar
K.-M. Lee, P.-Y. Chen, C.-P. Lee, and K.-C. Ho, “Binary room-temperature ionic liquids based electrolytes solidified with ${SiO}_{2}$ nanoparticles for dye-sensitized solar cells,” Journal of Power Sources, vol. 190, no. 2, pp. 573–577, 2009.
View at: Publisher Site | Google Scholar
T. Kato and S. Hayase, “Quasi-solid dye sensitized solar cell with straight ion paths. Proposal of hybrid electrolytes for ionic liquid-type electrolytes,” Journal of the Electrochemical Society, vol. 154, no. 1, pp. B117–B121, 2007.
View at: Publisher Site | Google Scholar
A. Kay and M. Grätzel, “Low cost photovoltaic modules based on dye sensitized nanocrystalline titanium dioxide and carbon powder,” Solar Energy Materials and Solar Cells, vol. 44, no. 1, pp. 99–117, 1996.
View at: Publisher Site | Google Scholar
T. N. Murakami, S. Ito, Q. Wang et al., “Highly efficient dye-sensitized solar cells based on carbon black counter electrodes,” Journal of the Electrochemical Society, vol. 153, no. 12, pp. A2255–A2261, 2006.
View at: Publisher Site | Google Scholar
Z. Huang, X. Liu, K. Li et al., “Application of carbon materials as counter electrodes of dye-sensitized solar cells,” Electrochemistry Communications, vol. 9, no. 4, pp. 596–598, 2007.
View at: Publisher Site | Google Scholar
C.-S. Chou, R.-Y. Yang, M.-H. Weng, and C.-I. Huang, “The applicability of SWCNT on the counter electrode for the dye-sensitized solar cell,” Advanced Powder Technology, vol. 20, no. 4, pp. 310–317, 2009.
View at: Publisher Site | Google Scholar
E. Ramasamy, W. J. Lee, D. Y. Lee, and J. S. Song, “Spray coated multi-wall carbon nanotube counter electrode for tri-iodide $(I_{3}^{-})$ reduction in dye-sensitized solar cells,” Electrochemistry Communications, vol. 10, no. 7, pp. 1087–1089, 2008.
View at: Publisher Site | Google Scholar
E. Ramasamy, W. J. Lee, D. Y. Lee, and J. S. Song, “Nanocarbon counterelectrode for dye sensitized solar cells,” Applied Physics Letters, vol. 90, no. 17, Article ID 173103, 2007.
View at: Publisher Site | Google Scholar
W. J. Lee, E. Ramasamy, D. Y. Lee, and J. S. Song, “Grid type dye-sensitized solar cell module with carbon counter electrode,” Journal of Photochemistry and Photobiology A, vol. 194, no. 1, pp. 27–30, 2008.
View at: Publisher Site | Google Scholar
S.-S. Kim, K.-W. Park, J.-H. Yum, and Y.-E. Sung, “Pt-NiO nanophase electrodes for dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 90, no. 3, pp. 283–290, 2006.
View at: Publisher Site | Google Scholar
S.-S. Kim, K.-W. Park, J.-H. Yum, and Y.-E. Sung, “Dye-sensitized solar cells with Pt-NiO and Pt- ${TiO}_{2}$ biphase counter electrodes,” Journal of Photochemistry and Photobiology A, vol. 189, no. 2-3, pp. 301–306, 2007.
View at: Publisher Site | Google Scholar
C. H. Yoon, R. Vittal, J. Lee, W.-S. Chae, and K.-J. Kim, “Enhanced performance of a dye-sensitized solar cell with an electrodeposited-platinum counter electrode,” Electrochimica Acta, vol. 53, no. 6, pp. 2890–2896, 2008.
View at: Publisher Site | Google Scholar
H. Fornander, J. Birch, P. Sandström, and J.-E. Sundgren, “Structure evolution of epitaxial Pd grown on MgO(001): a comparison between sputtering and electron-beam evaporation,” Thin Solid Films, vol. 349, no. 1, pp. 4–9, 1999.
View at: Publisher Site | Google Scholar
Z. Song and C. Lin, “Microstructure and electrical properties of ${PbZr}_{0.48} {Ti}_{0.52} O_{3}$ ferroelectric films on different Pt bottom electrodes,” Applied Surface Science, vol. 158, no. 1, pp. 21–27, 2000.
View at: Publisher Site | Google Scholar
K. Imoto, K. Takahashi, T. Yamaguchi, T. Komura, J.-I. Nakamura, and K. Murata, “High-performance carbon counter electrode for dye-sensitized solar cells,” Solar Energy Materials and Solar Cells, vol. 79, no. 4, pp. 459–469, 2003.
View at: Publisher Site | Google Scholar
X. Fang, T. Ma, G. Guan, M. Akiyama, T. Kida, and E. Abe, “Effect of the thickness of the Pt film coated on a counter electrode on the performance of a dye-sensitized solar cell,” Journal of Electroanalytical Chemistry, vol. 570, no. 2, pp. 257–263, 2004.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2010 Chuen-Shii Chou et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

4389

Downloads

2155

Citations

International Journal of Photoenergy

Thin-Film Photovoltaics

Preparation of a Counter Electrode with P-Type NiO and Its Applications in Dye-Sensitized Solar Cell

Abstract

1. Introduction

2. Experimental Details

2.1. Preparing and Measuring the Working Electrode

2.2. Preparing and Measuring the Counter Electrode

2.3. Assembling and Testing the DSSC

3. Results and Discussion

3.1. Characteristics of TiCl4 and NiO

3.2. Characteristics of the Counter Electrode

3.3. Photoelectrochemical Behaviour

4. Conclusion

Acknowledgments

References

Copyright

3.1. Characteristics of TiCl₄ and NiO