Table of Contents Author Guidelines Submit a Manuscript
International Journal of Polymer Science
Volume 2014, Article ID 201301, 7 pages
http://dx.doi.org/10.1155/2014/201301
Research Article

Copolymer SJ-1 as a Fluid Loss Additive for Drilling Fluid with High Content of Salt and Calcium

1School of Chemistry and Chemical Engineering, Southwest Petroleum University, Chengdu 610500, China
2Department of Education, Engineering Research Center of Oilfield Chemistry, Chengdu 610500, China

Received 4 May 2014; Revised 11 July 2014; Accepted 26 July 2014; Published 18 August 2014

Academic Editor: Saad Khan

Copyright © 2014 Hongping Quan et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. L. Ali and M. A. Barrufet, “Using centrifuge data to investigate the effects of polymer treatment on relative permeability,” Journal of Petroleum Science and Engineering, vol. 29, no. 1, pp. 1–16, 2001. View at Publisher · View at Google Scholar · View at Scopus
  2. T. Wan, J. Yao, S. Zishun, W. Li, and W. Juan, “Solution and drilling fluid properties of water soluble AM-AA-SSS copolymers by inverse microemulsion,” Journal of Petroleum Science and Engineering, vol. 78, no. 2, pp. 334–337, 2011. View at Publisher · View at Google Scholar · View at Scopus
  3. M. V. Kok, “Rheological and thermal analysis of bentonites for water base drilling fluids,” Energy Sources A: Recovery, Utilization, and Environmental Effects, vol. 26, no. 2, pp. 145–151, 2004. View at Google Scholar
  4. M. V. Kok, “A rheological characterization and parametric analysis of a bentonite sample,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 33, no. 4, pp. 344–348, 2011. View at Publisher · View at Google Scholar · View at Scopus
  5. Y. Zhuang, Z. Zhu, H. Chao, and B. Yang, “Effect of added salt on properties of aqueous SMP solution,” Journal of Applied Polymer Science, vol. 55, no. 7, pp. 1063–1067, 1995. View at Google Scholar
  6. M. V. Kok, “Thermal characterization of sepiolite samples,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 35, no. 2, pp. 173–183, 2013. View at Publisher · View at Google Scholar · View at Scopus
  7. M. V. Kok, “Statistical approach of two-three parameters rheological models for polymer type drilling fluid analysis,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 32, no. 4, pp. 336–345, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. M. V. Kok, “Thermal analysis and rheological study of ocma type bentonite used in drilling fluids,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 35, no. 2, pp. 122–133, 2013. View at Publisher · View at Google Scholar · View at Scopus
  9. C. Collette, F. Lafuma, R. Audebert, and R. Brouard, “Macromolecular systems in heat-resistant drilling fluids; advantages of gels on linear polymers,” Journal of Applied Polymer Science, vol. 53, no. 6, pp. 755–762, 1994. View at Publisher · View at Google Scholar · View at Scopus
  10. V. C. Kelessidis, C. Papanicolaou, and A. Foscolos, “Application of Greek lignite as an additive for controlling rheological and filtration properties of water-bentonite suspensions at high temperatures: a review,” International Journal of Coal Geology, vol. 77, no. 3-4, pp. 394–400, 2009. View at Publisher · View at Google Scholar · View at Scopus
  11. R. Caenn and G. V. Chillingar, “Drilling fluids: state of the art,” Journal of Petroleum Science and Engineering, vol. 14, no. 3-4, pp. 221–230, 1996. View at Publisher · View at Google Scholar · View at Scopus
  12. J. Plank, N. R. Lummer, and F. Dugonjić-Bilić, “Competitive adsorption between an AMPSV-based fluid loss polymer and Welan gum biopolymer in oil well cement,” Journal of Applied Polymer Science, vol. 116, no. 5, pp. 2913–2919, 2010. View at Publisher · View at Google Scholar · View at Scopus
  13. J. Y. Ma, H. L. Zheng, M. Z. Tan et al., “Synthesis, characterization, and flocculation performance of anionic polyacrylamide P (AM-AA-AMPS),” Journal of Applied Polymer Science, vol. 129, no. 4, pp. 1984–1991, 2013. View at Publisher · View at Google Scholar · View at Scopus
  14. C. Tiemeyer and J. Plank, “Synthesis, characterization, and working mechanism of a synthetic high temperature (200°C) fluid loss polymer for oil well cementing containing allyloxy-2-hydroxy propane sulfonic (AHPS) acid monomer,” Journal of Applied Polymer Science, vol. 128, no. 1, pp. 851–860, 2013. View at Publisher · View at Google Scholar · View at Scopus
  15. Y. Liu, W. P. Gates, A. Bouazza, and R. K. Rowe, “Fluid loss as a quick method to evaluate hydraulic conductivity of geosynthetic clay liners under acidic conditions,” Canadian Geotechnical Journal, vol. 51, no. 2, pp. 158–163, 2014. View at Publisher · View at Google Scholar
  16. Q. Xiao, W. F. Xiao, and X. X. Liu, “A novel cement fluid loss additive P1402,” Advanced Materials Research, vol. 941–944, pp. 1203–1207, 2014. View at Google Scholar
  17. S. Akimoto, S. Honda, and T. Yasukohchi, “Polyoxyalkylene alkenyl ether-maleic ester copolymer and use thereof,” US Patent 5142036, 1989. View at Google Scholar
  18. J. P. Plank, “Water-based muds using synthetic polymers developed for high temperature drilling,” Oil and Gas Journal, vol. 90, no. 9, pp. 40–45, 1992. View at Google Scholar · View at Scopus