Preparation of Oligosaccharides by Degradation of Polysaccharides from Chinese Jujube and Its Biological Activity

Yan, Xu; Wang, Weiwei; Liu, Mengjun; Zhao, Zhihui

doi:https://doi.org/10.1155/2018/6464051

International Journal of Polymer Science

On this page

Abstract Introduction Materials and Methods Results Discussion Conclusions Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 6464051 | https://doi.org/10.1155/2018/6464051

Preparation of Oligosaccharides by Degradation of Polysaccharides from Chinese Jujube and Its Biological Activity

Xu Yan,^1,2Weiwei Wang,²Mengjun Liu,²and Zhihui Zhao^1,2

Academic Editor: Ramar Thangam

Received08 Dec 2017

Accepted13 Feb 2018

Published19 Apr 2018

Abstract

This study examined the degradation of polysaccharides to oligosaccharides in Chinese jujube fruits. Using a response surface model, the degradation conditions of polysaccharides under acid hydrolysis and enzymatic hydrolysis were optimized in laboratory conditions. A degradation rate of 66.9% was obtained under optimum acid hydrolysis conditions: 0.6 mol/L hydrochloric acid, 3% substrate concentration, and 1 h reaction time. A degradation rate of 41.4% was obtained under optimum enzyme hydrolysis conditions: 4.0 mL cellulose solution (10 mg/mL), 0.3 mL substrate solution (20 mg/mL), 0.7 mL citric acid buffer solution (pH 5), and 7.3 h reaction time. Using the stimulation effect for strain J-4 intestinal probiotic proliferation, the biological activity of oligosaccharides was determined. The results showed that the oligosaccharides from enzyme hydrolysis encouraged intestinal probiotic proliferation.

1. Introduction

Chinese jujube (Ziziphus jujuba Mill.) is a native plant of China that belongs to the genus Ziziphus in the Rhamnaceae family. It is a medicinal plant with a long history (>7000 years) in China, where it is widely distributed (total growing area >2,000,000 ha). The fruits and seeds are used in traditional Chinese medicine where they are believed to have blood nourishing, sedation, antitumor, and immune-modulability properties, among others. The fruits are considered a “natural, healthy food” [1].

Response surface methodology (RSM), first introduced by Box [2], is an effective statistical method which can optimize complex processes. There are several recent studies that have used RSM to identify optimized conditions for the extraction of bioactive compounds from different sources [3–6]. The main advantage of RSM is the reduced number of experimental trials needed to evaluate multiple parameters and their interactions, which makes it less labor-intensive and time-consuming than other approaches [7].

Chinese jujube fruit is well-known for its high sugar content (60–80% dried; 25–30% fresh). Our previous studies revealed that jujube fruit is rich in not only glucose, fructose, and sucrose, but polysaccharides [8–10].

As a nondigestible carbohydrate, oligosaccharides are a component of dietary fiber and are of particular interest for their metabolic properties [11]. Particularly, oligosaccharides are considered to have prebiotic properties including the ability to stimulate probiotic bacteria [12, 13].

Apart from soybean oligosaccharides and raffinose (produced by direct extraction) and lactulose (produced by an isomerization reaction), the commercial production of oligosaccharides uses enzymatic processes [14]. Plant polysaccharides have been identified as potential sources for oligosaccharide production [15–18].

There is a lack of knowledge on the preparation of oligosaccharides from the degradation of water-soluble polysaccharides in jujube fruits. The objectives of this study were to optimize the degradation conditions of polysaccharides to oligosaccharides using acid hydrolysis and enzymatic hydrolysis and study the biological activity of oligosaccharides.

We believe that the knowledge gained from this study will help to further exploit and improve the utilization value of jujube and provide a theoretical support for the development of health food.

2. Materials and Methods

2.1. Chemicals

Deionized water was purified by an EPED superpurification system (Eped, Nanjing, China). All other reagent solutions were of analytical grade (Sinopharm Chemical Reagent Co., Ltd., Shanghai, China). Dialysis tubes were from Spectrum Laboratories, Inc. (USA).

2.2. Fruit Material and Treatment

Samples of Chinese jujube “Jinsixiaozao” fruits were collected from Cang County, Cangzhou, China. The trees were managed according to integrated cultivation protocols, with all the fruits transported to the laboratory in isothermal boxes containing ice. The fruits were divided into pulp and shells with a knife. The pulp was cut into thin strips with a knife and dried at 55°C in a DGG-9203A constant temperature drying oven (Senxin Experiment Corporation, Shanghai, China). The dried jujube pulp was crushed using a universal high-speed smashing machine (Hongtaiyang Electromechanical Corporation, Yongkang, China), and the smashed dried pulp passed through a 70-mesh sieve. The powder was collected and stored in a desiccator at room temperature (15–20°C) until needed.

2.3. Preparation of Oligosaccharides by Polysaccharide Degradation

2.3.1. Preparation of Polysaccharides

In order to remove lipids in jujube, the jujube powder was refluxed with 80% ethanol three times for 1.5 h each time at 100°C. After filtration, the residue was dried at room temperature and then extracted with boiling water twice for 2 h each time. The water extract was combined, concentrated, and precipitated with three volumes of 95% ethanol at 4°C overnight. The precipitate was washed with ethanol absolute and deproteinized using the Sevage method [19] before being concentrated and freeze-dried to obtain the crude polysaccharide.

2.3.2. Selection and Optimization of Acid Hydrolysis Conditions of Polysaccharides

At 90°C, the appropriate range of relevant factors that affect the degradation rate of polysaccharides (concentration of hydrochloric acid, amount of different substrates, and time of acid hydrolysis) was determined from single factor experiments. The factor levels for each individual experiment were 0.1, 0.2, 0.5, 1.0, 1.5, and 2 mol/L hydrochloric acid; 0.2%, 0.5%, 1.0%, 2.0%, 3.0%, and 4.0% of different substrates; and 0.5 h, 1.0 h, 1.5 h, 2.0 h, 2.5 h, and 3.0 h for acid hydrolysis.

RSM was used to optimize the acid hydrolysis conditions of polysaccharides. A Box-Behnken design (BBD) with three independent variables—hydrochloric acid concentration , substrate , and acid hydrolysis time —was used. The input range of the selected variables was determined in preliminary RSM experiments. The three independent variables were coded at three levels (−1, 0, 1), which resulted in an experimental design with 15 experimental points, including three central points to evaluate the pure error. Design Expert V8.0.6 (Stat-Ease Inc., Minneapolis, USA) was used to design the experiments and analyze the data.

Experimental data were analyzed to fit a second-order polynomial model. The models were predicted through statistical analysis and regression analysis (ANOVA) using Design Expert V8.0.6. This software was also used to obtain the coefficients of the quadratic polynomial model. The quality of the fitted model was expressed by the coefficient of determination , and its statistical significance was checked with an -test.

2.3.3. Selection and Optimization of Enzymatic Hydrolysis Conditions of Polysaccharides

The reaction system (5 mL) included the polysaccharide solution (20 mg/mL), enzyme solution (10 mg/mL), and citric acid buffer solution (pH 5). Different volumes of enzyme solution, substrate, and citric acid buffer solution (pH 5) were reacted at 45°C in a water bath to degrade the polysaccharides. The single factor test was used to analyze the three factors (amount of enzyme, amount of substrate, and enzymatic hydrolysis time) to identify the appropriate range of each factor. The levels for each factor were 0.5 mL, 1 mL, 2 mL, 3 mL, and 4 mL of enzyme, 0.5 mL, 1 mL, 2 mL, 3 mL, and 4 mL of substrate, and 1 h, 2 h, and 3 h to 8 h for enzymatic hydrolysis.

Based on the single factor test, a Box-Behnken design (BBD) with three independent variables—amount of different enzymes , substrate , and enzymatic hydrolysis time —was used. The input range of the selected variables was determined in preliminary RSM experiments.

2.3.4. Calculation of Degradation Rate

After polysaccharide degradation, the unhydrolyzed polysaccharides and cellulase were precipitated by adding three volumes of 95% ethanol and removed by centrifugation. The solution was then dialyzed in a MD10 dialysis tube to remove any small molecules. The inside part was collected and lyophilized to extract the oligosaccharides. The sugar contents in the polysaccharide and oligosaccharide samples were determined using the Calorimetric Dubois Method [20]. The degradation rate (DR) was calculated from the ratio of the sugar content in the oligosaccharide and polysaccharide.

2.4. Activity of Oligosaccharides

Strain J-4 with antagonistic activity against E. coli was isolated from the cecum of healthy chickens and provided by the Department of Pharmaceutical Engineering, College of Life Sciences, Hebei Agricultural University.

The basal fermentation medium included 2% glucose, 2% peptone, 0.2% NaH₂PO₄•2H₂O, 0.4% Na₂HPO₄•2H₂O, 0.05% MgSO₄•5H₂O, and 0.02% CaCl₂ at pH 7.2–7.4. To determine the effect of the oligosaccharides prepared by polysaccharide degradation on the growth of strain J-4 intestinal probiotics in vitro, oligosaccharides at different concentrations (0.25%, 0.50%) were added to the basal medium in place of glucose to culture the intestinal probiotics. The growth of bacteria was measured at 600 nm wavelength (OD₆₀₀) at 12 h, 14 h, and 16 h into the culture period [21].

2.5. Statistical Analysis

All of the experiments were conducted in triplicate. values < 0.05 and < 0.01 were regarded as significant and highly significant, respectively. The direction and magnitude of the correlation between the variables were quantified by the square of the correlation coefficient, R.

3. Results

3.1. Optimization of Acid Hydrolysis from Jujube Polysaccharides

Acid hydrolysis was used to extract polysaccharides from Chinese jujube “Jinsixiaozao.” The operational parameters were optimized using the Box-Behnken design based on RSM. All experimental data obtained from the 15-run experiment are shown in Table 1.

Experimental values for the extraction efficiency of the degradation conditions of polysaccharide by acid hydrolysis (Table 1) were analyzed using multiple regressions to fit the second-order regression equation, and the regression model in terms of coded factors was predicted as follows:

Y denotes the response function (DR) and , , and are the encoded values of the three independent variables.

The coefficients in (1) were calculated using RSM, and statistical analysis of the experimental data was used to establish the best-fit model for the independent variables. The model had a satisfactory level of adequacy (Table 2). The response values were significantly affected by all three parameters, suggesting that they were directly related to the degradation rate.

The analysis of variance (ANOVA) of the model is shown in Table 2. The calculated model explained 96.59% of the polysaccharide degradation rate. Moreover, the adjusted correlation coefficient of determination (RAdj²) of the equation was 0.9044, which suggests an excellent correlation between any two independent variables. The corresponding variables would be more significant if the absolute -value increased and the value decreased. The statistical analysis produced a high -value (15.7242) and a very low value (), which implies that the model is significant. Lack of fit (, not significant) confirmed the validity of the model. The results indicate that the model worked well for the analysis and prediction of degradation conditions of polysaccharide using acid hydrolysis. Table 2 shows that , , and had no significant effect on the oligosaccharide conversion.

According to the regression equation of the model, fixing a factor in the encoding value “0” level, the effect of two factors was analyzed on the conversion rate of oligosaccharides in the process of acid degradation by Expert Design software (Figure 1). The 3D response surface plots showed that when the acid concentration was at 0.5 mol/L, substrate concentration and time affected the conversion rate (Figure 1); the substrate and acid concentration affected the degradation rate when the time was at 1.0 h; and when the substrate concentration was 3.0%, the other two factors affected the degradation rate. There was an extreme value in the selected range which was the highest point of response surface.

(a)

(b)

(c)

According to the results of 15 experiments, the predicted optimized conditions—0.6 mol/L hydrochloric acid, 3.1% substrate concentration, and 1.1 h of acid hydrolysis—produced a conversion rate of 67.2%. To confirm the accuracy of the model, three verification tests were carried out, and the conditions were slightly modified to make them more feasible—0.6 mol/L hydrochloric acid, 3% substrate concentration, and 1 h of acid hydrolysis—and produced a degradation rate of 66.9%, which was close to the predicted value. Therefore, we believe that this model is credible.

3.2. Optimization of Enzymatic Hydrolysis from Jujube Polysaccharide

All experimental data obtained from 15-run experiment are shown in Table 3. Experimental values for the extraction efficiency of degradation conditions of polysaccharide using enzymatic hydrolysis (Table 3) were analyzed using multiple regressions to fit the second-order regression equation, and the regression model in terms of coded factors was predicted as follows:

denotes the response function (DR) and , , and are the encoded values of the three independent variables.

The coefficients of (2) were calculated using RSM, and statistical analysis of the experimental data was used to establish the best-fit model for the independent variables. The model had satisfactory levels of adequacy (Table 4). The response values were significantly affected by all three parameters, suggesting that they were directly related to the degradation rate.

The ANOVA result of the model is shown in Table 4. The calculated model explained 97.7% of the degradation rate. Moreover, the adjusted correlation coefficient of determination (RAdj²) was 0.9351, which suggests an excellent correlation between any two independent variables. The statistical analysis produced a high -value (23.4) and a very low value (), implying that the model was significant. Lack of fit (, not significant) confirmed the validity of the model. The results indicate that the model could work well for the analysis and prediction of degradation conditions of polysaccharide by enzymatic hydrolysis. Table 4 shows that , , and do not have a significant effect on the oligosaccharide conversion rate, while the others were significant.

The 3D response surface plots show that, with 4 mL of enzyme, the substrate concentration and enzyme time affected the conversion rate (Figure 2); at 7.0 h, the substrate and enzyme amount affected the rate; and at 0.5 mL of substrate, the enzyme amount and time affected the rate. There was an extreme value in the selected range which was the highest point of the response surface.

(a)

(b)

(c)

To confirm the accuracy of the model, three verification tests were carried out, and the conditions were slightly modified to make them more feasible—4.0 mL of enzyme (10 mg/mL), 0.3 mL of substrate (20 mg/mL), 0.7 mL of citric acid buffer solution (pH 5), and 7.3 h of enzymatic hydrolysis—and produced a conversion rate of 41.4%, which was close to the predicted value. Therefore, we believe that this model is credible.

3.3. Biological Activity of Oligosaccharides

The effect of different concentrations and different sources of Chinese jujube oligosaccharides on the promotion of intestinal probiotics was determined in vitro. Glucose in basal culture medium was replaced by different concentrations of oligosaccharides that had been prepared by polysaccharide hydrolysis as a carbon source. Since the concentration of bacterial suspension was proportional to the turbidity, the OD₆₀₀ value of fermentation liquor was monitored every two hours after inoculation for bacterial growth.

The activities of two types of oligosaccharides, prepared using different methods, were determined with strain J-4 intestinal probiotics.

With the oligosaccharide from acid hydrolysis, strain J-4 intestinal probiotics had a significantly lower growth rate than that of the basal culture medium (Figure 3). It is suggested that oligosaccharide obtained by acid hydrolysis has low activity. The oligosaccharide obtained by enzyme hydrolysis had a significantly higher growth rate of J-4 intestinal probiotics than the basal medium (; Figure 4).

4. Discussion

According to our research (data not shown), Chinese jujube fruits have low levels of natural oligosaccharides. It is difficult to extract oligosaccharides from the fruit directly. However, the content of jujube polysaccharides in the fruit is somewhat higher [22, 23]. It is reported that the high degree of polymerization, large molecular space, and low bioavailability have greatly restricted the application of polysaccharides in the food, pharmaceutical, and chemical industries and other fields [24]. It can, however, be degraded to oligosaccharides. Oligosaccharides formed by hydrolysis have a variety of biological activities [25]. In this study, two methods were used to prepare the oligosaccharides—acid hydrolysis and enzyme hydrolysis—which produced degradation rates of 66.9% and 41.4%, respectively. Moreover, the degradation rates were higher than that of other plants [24, 26, 27].

The yield of oligosaccharides prepared by enzyme hydrolysis was lower than those prepared by acid hydrolysis. However the activity of enzyme hydrolysis oligosaccharides was higher than that from acid hydrolysis. Wang believes that the reaction conditions of acid hydrolysis are more severe—destroying the structure of sugar—than the milder enzyme hydrolysis [28]. This may explain why the enzyme hydrolysis oligosaccharides had better activity on strain J-4 intestinal probiotics.

In this study, we extracted oligosaccharides through polysaccharide degradation of Chinese jujube. The exact structural information and bioactivities of these oligosaccharides need further study.

This experiment has laid a foundation for further studies on the degradation of jujube polysaccharides and provided a reference for the development of new functional oligosaccharides and a new direction for the development and utilization of Chinese jujube.

5. Conclusions

By incorporating a response surface model, the degradation conditions of jujube polysaccharides using acid hydrolysis and enzyme hydrolysis were studied. The optimum acid hydrolysis conditions were 0.6 mol/L hydrochloric acid, 3% substrate concentration, and a 1 h reaction time. The optimum enzyme hydrolysis conditions were 4.0 mL of enzyme (10 mg/mL), 0.3 mL of substrate (20 mg/mL), 0.7 mL of citric acid buffer solution (pH 5), and 7.3 h of enzymatic hydrolysis. Under these conditions, the degradation rate of acid hydrolysis and enzyme hydrolysis was 66.9% and 41.4%, respectively. The oligosaccharides from enzyme hydrolysis encouraged intestinal probiotic proliferation.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This work was funded by Xinjiang Production & Construction Corps Key Laboratory of Protection and Utilization of Biological Resources in Tarim Basin (BRZD1302), Young Academic Leaders Project of Hebei Agricultural University, and Top-Notch Talent Support Project of Hebei Province.

References

M. Liu, “Chinese Jujube: Botany and Horticulture,” Horticultural Reviews, vol. 32, pp. 229–298, 2006.
View at: Publisher Site | Google Scholar
G. E. P. Box and N. R. Draper, “Introduction to response surface methodology,” Response Surfaces, Mixtures, and Ridge Analyses, pp. 1–16, 2006.
View at: Publisher Site | Google Scholar
N. Ilaiyaraja, K. R. Likhith, G. R. Sharath Babu, and F. Khanum, “Optimisation of extraction of bioactive compounds from Feronia limonia (wood apple) fruit using response surface methodology (RSM),” Food Chemistry, vol. 173, pp. 348–354, 2015.
View at: Publisher Site | Google Scholar
B. Guldiken, D. Boyacioglu, and E. Capanoglu, “Optimization of Extraction of Bioactive Compounds from Black Carrot Using Response Surface Methodology (RSM),” Food Analytical Methods, vol. 9, no. 7, pp. 1876–1886, 2016.
View at: Publisher Site | Google Scholar
V. Kumar and H. K. Sharma, “Process optimization for extraction of bioactive compounds from taro (Colocasia esculenta), using RSM and ANFIS modeling,” Journal of Food Measurement and Characterization, vol. 11, no. 2, pp. 704–718, 2017.
View at: Publisher Site | Google Scholar
V. Ganesan, V. Gurumani, S. Kunjiappan, T. Panneerselvam, and B. Somasundaram, “Optimization and analysis of microwave-assisted extraction of bioactive compounds from Mimosa pudica L. using RSM ANFIS modeling,” Journal of Food Measurement and Characterization, 2017.
View at: Google Scholar
K. Zhong and Q. Wang, “Optimization of ultrasonic extraction of polysaccharides from dried longan pulp using response surface methodology,” Carbohydrate Polymers, vol. 80, no. 1, pp. 19–25, 2010.
View at: Publisher Site | Google Scholar
Z. Zhao, J. Li, X. Wu et al., “Structure and immunological activity of a pectic polysaccharide from the fruits of Ziziphus jujuba Mill. cv. jinsixiaozao Hort,” Chemistry of Natural Compounds, vol. 43, pp. 374–376, 2007.
View at: Publisher Site | Google Scholar
Z. Zhao, M. Liu, and P. Tu, “Characterization of water soluble polysaccharides from organs of Chinese Jujube (Ziziphus jujuba Mill. cv. dongzao),” European Food Research and Technology, vol. 226, no. 5, pp. 985–989, 2008.
View at: Publisher Site | Google Scholar
Z. Zhao, J. Li, X. Wu et al., “Structures and immunological activities of two pectic polysaccharides from fruits of Ziziphus jujuba Mill. cv. Jinsixiaozao Hort,” Food Research International, vol. 39, no. 8, pp. 917–923, 2006.
View at: Publisher Site | Google Scholar
J. M. Laparra, E. Tako, R. P. Glahn, and D. D. Miller, “Supplemental inulin does not enhance iron bioavailability to Caco-2 cells from milk- or soy-based, probiotic-containing, yogurts but incubation at 37 °C does,” Food Chemistry, vol. 109, no. 1, pp. 122–128, 2008.
View at: Publisher Site | Google Scholar
M. B. Akin, M. S. Akin, and Z. Kirmaci, “Effects of inulin and sugar levels on the viability of yogurt and probiotic bacteria and the physical and sensory characteristics in probiotic ice-cream,” Food Chemistry, vol. 104, no. 1, pp. 93–99, 2007.
View at: Publisher Site | Google Scholar
F. C. A. Buriti, H. R. Cardarelli, T. M. C. C. Filisetti, and S. M. I. Saad, “Synbiotic potential of fresh cream cheese supplemented with inulin and Lactobacillus paracasei in co-culture with Streptococcus thermophilus,” Food Chemistry, vol. 104, no. 4, pp. 1605–1610, 2007.
View at: Publisher Site | Google Scholar
S. I. Mussatto and I. M. Mancilha, “Non-digestible oligosaccharides: A review,” Carbohydrate Polymers, vol. 68, no. 3, pp. 587–597, 2007.
View at: Publisher Site | Google Scholar
G. G. Dutton, K. L. Mackie, A. V. Savage, D. Rierger-Hug, and S. Stirm, “Preparation of oligosaccharides by bacteriophage degradation of polysaccharides from Klebsiella serotypes K21 and K32,” Carbohydrate Research, vol. 84, no. 1, pp. 161–170, 1980.
View at: Publisher Site | Google Scholar
M. Lahaye, M. Brunel, and E. Bonnin, “Fine chemical structure analysis of oligosaccharides produced by an ulvan-lyase degradation of the water-soluble cell-wall polysaccharides from Ulua sp. (Ulvales, Chlorophyta),” Carbohydrate Research, vol. 304, no. 3-4, pp. 325–333, 1997.
View at: Publisher Site | Google Scholar
Z.-Y. Zhu, J.-Y. Zhang, F. Liu, L. Chen, L.-J. Chen, and Y. Tang, “Characterization and lymphocyte proliferation activity of an oligosaccharide degraded from Astragalus polysaccharide,” MedChemComm, vol. 8, no. 7, pp. 1521–1530, 2017.
View at: Publisher Site | Google Scholar
N. Khodaei and S. Karboune, “Enzymatic generation of galactose-rich oligosaccharides/oligomers from potato rhamnogalacturonan i pectic polysaccharides,” Food Chemistry, vol. 197, pp. 406–414, 2016.
View at: Publisher Site | Google Scholar
L. Navarini, R. Gilli, V. Gombac, A. Abatangelo, M. Bosco, and R. Toffanin, “Polysaccharides from hot water extracts of roasted Coffea arabica beans: Isolation and characterization,” Carbohydrate Polymers, vol. 40, no. 1, pp. 71–81, 1999.
View at: Publisher Site | Google Scholar
M. Dubois, K. A. Gilles, J. K. Hamilton, P. A. Rebers, and F. Smith, “Colorimetric method for determination of sugars and related substances,” Analytical Chemistry, vol. 28, no. 3, pp. 350–356, 1956.
View at: Publisher Site | Google Scholar
V. D. Badwaik, L. M. Vangala, D. S. Pender et al., “Size-dependent antimicrobial properties of sugarencapsulated gold nanoparticles synthesized by a green method,” Nanoscale Research Letters, vol. 7, no. 1, p. 623, 2012.
View at: Publisher Site | Google Scholar
H. Rostami and S. M. T. Gharibzahedi, “Microwave-assisted extraction of jujube polysaccharide: optimization, purification and functional characterization,” Carbohydrate Polymers, vol. 143, pp. 100–107, 2016.
View at: Publisher Site | Google Scholar
B. Wang, “Chemical characterization and Ameliorating effect of polysaccharide from Chinese jujube on intestine oxidative injury by ischemia and reperfusion,” International Journal of Biological Macromolecules, vol. 48, no. 3, pp. 386–391, 2011.
View at: Publisher Site | Google Scholar
K. Hu, Q. Liu, S. Wang, and K. Ding, “New oligosaccharides prepared by acid hydrolysis of the polysaccharides from Nerium indicum Mill and their anti-angiogenesis activities,” Carbohydrate Research, vol. 344, no. 2, pp. 198–203, 2009.
View at: Publisher Site | Google Scholar
F. A. de Moura, F. T. Macagnan, and L. P. da Silva, “Oligosaccharide production by hydrolysis of polysaccharides: A review,” International Journal of Food Science & Technology, vol. 50, no. 2, pp. 275–281, 2015.
View at: Publisher Site | Google Scholar
S. Liu, X. Wan, and X. Du, “Enzymatic preparation of cello-oligosaccharides from Radix puerariae fiber,” Food Science, vol. 23, no. 4, pp. 66–70, 2012.
View at: Google Scholar
S. Huang, Z. Wang, and X. Liu, “Study on enzymatic degradation of tea polysaccharide,” China Feed, vol. no. 16, pp. 39–41, 2012.
View at: Google Scholar
F. Wang, G. Hu, J. Xiao, and Y. Liu, “Improvement in the productivity of xylooligosaccharides from rice straw by feed xylanase with ultrafiltration,” Archives of Biological Sciences, vol. 63, no. 1, pp. 161–166, 2011.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2018 Xu Yan et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2629

Downloads

1261

Citations